Ni(II)-doped CuWO4 photoanodes with enhanced photoelectrocatalytic activity.

CuWO4 has emerged in the last years as a ternary metal oxide material for photoanodes application in photoelectrochemical cells, thanks to its relatively narrow band gap, high stability and selectivity toward the oxygen evolution reaction, though largely limited by its poor charge separation efficiency. Aiming at overcoming this limitation, we investigate here the effects that Cu(II) ion substitution has on the photoelectrocatalytic (PEC) performance of copper tungstate. Optically transparent CuWO4 thin-film photoanodes, prepared via spin coating and containing different amounts of Ni(II) ions, were fully characterized via UV-Vis spectroscopy, XRD and SEM analyses, and their PEC performance was tested via linear sweep voltammetry, incident photon to current efficiency and internal quantum efficiency analyses. From tests performed in the presence of a hole scavenger-containing electrolyte, the charge injection and separation efficiencies of the electrodes were also calculated. Pure-phase crystalline and/or heterojunction materials were obtained with higher PEC performance compared to pure CuWO4, mainly due to a significantly enhanced charge separation efficiency in the bulk of the material.

Tuning Polyamidoamine Design To Increase Uptake and Efficacy of Ruthenium Complexes for Photodynamic Therapy.

In this work, we report the synthesis of [Ru(phen)32+]-based complexes and their use as photosensitizers for photodynamic therapy (PDT), a treatment of pathological conditions based on the photoactivation of bioactive compounds, which are not harmful in the absence of light irradiation. Of these complexes, Ru-PhenISA and Ru-PhenAN are polymer conjugates containing less than 5%, (on a molar basis), photoactive units. Their performance is compared with that of a small [Ru(phen)32+] compound, [Ru(phen)2BAP](OTf)2 (BAP = 4-(4'-aminobutyl)-1,10-phenanthroline, OTf = triflate anion), used as a model of the photoactive units. The polymer ligands, PhenISA and PhenAN, are polyamidoamines with different acid-base properties. At physiological pH, the former is zwitterionic, the latter moderately cationic, and both intrinsically cytocompatible. The photophysical characterizations show that the complexation to macromolecules does not hamper the Ru(phen)32+ ability to generate toxic singlet oxygen upon irradiation, and phosphorescence lifetimes and quantum yields are similar in all cases. All three compounds are internalized by HeLa cells and can induce cell death upon visible light irradiation. However, their relative PDT efficiency is different: the zwitterionic PhenISA endowed with the Ru-complex lowers the PDT efficiency of the free complex, while conversely, the cationic PhenAN boosts it. Flow cytometry demonstrates that the uptake efficiency of the three agents reflects the observed differences in PDT efficacy. Additionally, intracellular localization studies show that while [Ru(phen)2BAP](OTf)2 remains confined in vesicular structures, Ru-PhenISA localization is hard to determine due to the very low uptake efficiency. Very interestingly, instead, the cationic Ru-PhenAN accumulates inside the nucleus in all treated cells. Overall, the results indicate that the complexation of [Ru(phen)2BAP](OTf)2 with a cationic polyamidoamine to give the Ru-PhenAN complex is an excellent strategy to increase the Ru-complex cell uptake and, additionally, to achieve accumulation at the nuclear level. These unique features together make this compound an excellent photosensitizer with very high PDT efficiency.

Photoinduced Charge-Transfer Dynamics in WO3/BiVO4 Photoanodes Probed through Midinfrared Transient Absorption Spectroscopy.

The dynamics of photopromoted electrons in BiVO4, WO3, and WO3/BiVO4 heterojunction electrodes has been directly probed by transient absorption (TA) midinfrared (mid-IR) spectroscopy in the picosecond to microsecond time range. By comparison of the dynamics recorded with the two individual oxides at 2050 cm-1 with that of the heterojunction system after excitation at different wavelengths, electron-transfer processes between selectively excited BiVO4 and WO3 have been directly tracked for the first time. These results support the charge carrier interactions which were previously hypothesized by probing the BiVO4 hole dynamics through TA spectroscopy in the visible range. Nanosecond mid-IR TA experiments confirmed that charge carrier separation occurs in WO3/BiVO4 electrodes under visible-light excitation, persisting up to the microsecond time scale.

A luminescent poly(amidoamine)-iridium complex as a new singlet-oxygen sensitizer for photodynamic therapy.

A polymer complex (1P) was synthesized by binding bis(cyclometalated) Ir(ppy)2(+) fragments (ppy = 2-phenylpyridyl) to phenanthroline (phen) pendants of a poly(amidoamine) copolymer (PhenISA, in which the phen pendants involved ∼6% of the repeating units). The corresponding molecular complex [Ir(ppy)2(bap)](+) (1M, bap = 4-(butyl-4-amino)-1,10-phenanthroline) was also prepared for comparison. In water solution 1P gives nanoaggregates with a hydrodynamic diameter of 30 nm in which the lipophilic metal centers are presumed to be segregated within polymer tasks to reduce their interaction with water. Such confinement, combined with the dilution of triplet emitters along the polymer chains, led to 1P having a photoluminescence quantum yield greater than that of 1M (0.061 vs 0.034, respectively, in an aerated water solution) with a longer lifetime of the (3)MLCT excited states and a blue-shifted emission (595 nm vs 604 nm, respectively). NMR data supported segregation of the metal centers. Photoreaction of O2 with 1,5-dihydroxynaphthalene showed that 1P is able to sensitize (1)O2 generation but with half the quantum yield of 1M. Cellular uptake experiments showed that both 1M and 1P are efficient cell staining agents endowed with two-photon excitation (TPE) imaging capability. TPE microscopy at 840 nm indicated that both complexes penetrate the cellular membrane of HeLa cells, localizing in the perinuclear region. Cellular photodynamic therapy tests showed that both 1M and 1P are able to induce cell apoptosis upon exposure to Xe lamp irradiation. The fraction of apoptotic cells for 1M was higher than that for 1P (74 and 38%, respectively) 6 h after being irradiated for 5 min, but cells incubated with 1P showed much lower levels of necrosis as well as lower toxicity in the absence of irradiation. More generally, the results indicate that cell damage induced by 1M was avoided by binding the iridium sensitizers to the poly(amidoamine).

Photocatalytic activity of NH4F-doped TiO2 modified by noble metal nanoparticle deposition.

The effect of noble metal (Pt and Au) nanoparticle photodeposition on a series of NH4F-doped TiO2 photocatalysts calcined at 700 °C was investigated both in a thermodynamically down-hill reaction, i.e. the degradation of formic acid in aqueous suspension, and in an up-hill reaction, i.e. hydrogen production from methanol-water vapour mixtures. All photocatalysts were characterized by BET, XRD, UV-vis absorption and HRTEM analysis. Intriguing synergistic effects of simultaneous bulk and surface TiO2 modification were evidenced in both photocatalytic reactions, which can be interpreted in relation to the structural features of the materials. On one hand NH4F doping guarantees that the most active TiO2 anatase phase is stabilised up to high calcination temperature, ensuring high crystallinity and good photoinduced charge carriers production, on the other hand noble metal nanoparticles contribute in increasing the separation of photoproduced charge carriers, resulting in enhanced photocatalytic performances of the surface- and bulk-modified photocatalyst systems.

Nature of Charge Carrier Recombination in CuWO4 Photoanodes for Photoelectrochemical Water Splitting.

CuWO4 is a ternary semiconductor oxide with excellent visible light harvesting properties up to 550 nm and stability at high pH values, which make it a suitable material to build photoanodes for solar light conversion to hydrogen via water splitting. In this work, we studied the photoelectrochemical (PEC) performance of transparent CuWO4 electrodes with tunable light absorption and thickness, aiming at identifying the intrinsic bottlenecks of photogenerated charge carriers in this semiconductor. We found that electrodes with optimal CuWO4 thickness exhibit visible light activity due to the absorption of long-wavelength photons and a balanced electron and hole extraction from the oxide. The PEC performance of CuWO4 is light-intensity-dependent, with charge recombination increasing with light intensity and most photogenerated charge carriers recombining in bulk sites, as demonstrated by PEC tests performed in the presence of sacrificial agents or cocatalysts. The best-performing 580 nm thick CuWO4 electrode delivers a photocurrent of 0.37 mA cm-2 at 1.23 VSHE, with a 7% absorbed photon to current efficiency over the CuWO4 absorption spectrum.

Improved Photoelectrochemical Performance of WO3/BiVO4 Heterojunction Photoanodes via WO3 Nanostructuring.

WO3/BiVO4 heterojunction photoanodes can be efficiently employed in photoelectrochemical (PEC) cells for the conversion of water into molecular oxygen, the kinetic bottleneck of water splitting. Composite WO3/BiVO4 photoelectrodes possessing a nanoflake-like morphology have been synthesized through a multistep process and their PEC performance was investigated in comparison to that of WO3/BiVO4 photoelectrodes displaying a planar surface morphology and similar absorption properties and thickness. PEC tests, also in the presence of a sacrificial hole scavenger, electrochemical impedance analysis under simulated solar irradiation, and incident photon to current efficiency measurements highlighted that charge transport and charge recombination issues affecting the performance of the planar composite can be successfully overcome by nanostructuring the WO3 underlayer in nanoflake-like WO3/BiVO4 heterojunction electrodes.

Enhanced Charge Carrier Separation in WO3/BiVO4 Photoanodes Achieved via Light Absorption in the BiVO4 Layer.

Photoelectrochemical (PEC) water splitting converts solar light and water into oxygen and energy-rich hydrogen. WO3/BiVO4 heterojunction photoanodes perform much better than the separate oxide components, though internal charge recombination undermines their PEC performance when both oxides absorb light. Here we exploit the BiVO4 layer to sensitize WO3 to visible light and shield it from direct photoexcitation to overcome this efficiency loss. PEC experiments and ultrafast transient absorption spectroscopy performed by frontside (through BiVO4) or backside (through WO3) irradiating photoanodes with different BiVO4 layer thickness demonstrate that irradiation through BiVO4 is beneficial for charge separation. Optimized electrodes irradiated through BiVO4 show 40% higher photocurrent density compared to backside irradiation.

Photocatalytic activity of S- and F-doped TiO(2) in formic acid mineralization.

Two series of doped titanium dioxide samples (S-TiO(2) and F-TiO(2)) were prepared by the sol-gel method in the presence of different amounts of dopant source (thiourea and NH(4)F, respectively), followed by calcination at 500, 600 or 700 °C, and characterised by BET, UV-vis absorption, XPS, HRTEM, XRD and EPR analyses. Reference undoped materials were prepared by the same synthetic procedure. Their photocatalytic activity under visible light was investigated employing the photocatalytic degradation of formic acid in aqueous suspension as test reaction. S-doped TiO(2) showed a photocatalytic activity quite similar to that of undoped materials. In this regard, the insertion of S, characterised by a relatively large ionic radius, into the TiO(2) crystalline structure appears rather difficult, as confirmed by XPS analysis. On the contrary, moderate F doping was beneficial in increasing the rate of formic acid photocatalytic degradation, especially for photocatalysts calcined at high temperature, consisting of highly crystalline pure anatase, in which the rate of detrimental charge carrier recombination was reduced. For both series of doped materials, high doping levels appear to limit the semiconductor photoactivity, probably due to the formation of a progressively increasing number of charge recombination centres. The EPR characterisation of the investigated doped TiO(2) samples evidenced the presence of nitrogen containing species (nitric oxide radical encapsulated in micro-void, with no photoactivity, and N(b)˙ species, active in visible light sensitisation) and of titanium reduced centres Ti(3+), due to charge imbalance consequent to dopant introduction in the TiO(2) lattice either in anionic (F(-)) or in cationic form (S(6+)).

Absorption and action spectra analysis of ammonium fluoride-doped titania photocatalysts.

The photocatalytic behaviour of a series of ammonium fluoride (NH(4)F)-doped titania (TiO(2)) photocatalysts was investigated in the decomposition of acetic acid in aqueous suspensions and in the gas phase mineralization of acetaldehyde. Very similar photocatalytic activity trends, usually increasing with increasing the calcination temperature for a given nominal dopant amount, were obtained for the two test reactions. Moderately doped TiO(2) calcined at 700 °C, consisting of pure anatase, was the best performing photocatalyst in both reactions. The photocatalytic oxidation of acetic acid was investigated systematically as a function of irradiation wavelength, by collecting so-called action spectra. By comparing the shapes of the action spectra with those of the absorption spectra of the investigated photocatalysts a model is proposed, based on spectral features deconvolution, which allows a clear distinction between inactive light absorption and effective photoactivity in acetic acid decomposition.

Ultrafast Charge Carrier Dynamics in CuWO4 Photoanodes.

CuWO4 is a ternary metal oxide semiconductor with promising properties for photoelectrochemical (PEC) water splitting and solar light conversion, due to its quite low band gap (2.3 eV) and high stability in an alkaline environment. Aiming at understanding the origin of the relatively low PEC efficiency attained with CuWO4 photoanodes, we here investigate transparent CuWO4 electrodes prepared by a simple solution-based method through the combination of femtosecond transient absorption spectroscopy with electrochemical, PEC, and photochromic characterizations. The very fast recombination dynamics of the charge carriers photogenerated in CuWO4, which is the reason for its low efficiency, is discussed in relation with its PEC performance and with the recently calculated band structure of this material, also in comparison with the behavior of other semiconductor oxides employed in PEC applications, in particular Fe2O3.

WO3/BiVO4 Photoanodes: Facets Matching at the Heterojunction and BiVO4 Layer Thickness Effects.

Photoelectrochemical solar energy conversion offers a way to directly store light into energy-rich chemicals. Photoanodes based on the WO3/BiVO4 heterojunction are most effective mainly thanks to the efficient separation of photogenerated charges. The WO3/BiVO4 interfacial space region in the heterojunction is investigated here with the increasing thickness of the BiVO4 layer over a WO3 scaffold. On the basis of X-ray diffraction analysis results, density functional theory simulations show a BiVO4 growth over the WO3 layer along the BiVO4 {010} face, driven by the formation of a stable interface with new covalent bonds, with a favorable band alignment and band bending between the two oxides. This crystal facet phase matching allows a smooth transition between the electronic states of the two oxides and may be a key factor ensuring the high efficiency attained with this heterojunction. The photoelectrochemical activity of the WO3/BiVO4 photoanodes depends on both the irradiation wavelength and the thickness of the visible-light-absorbing BiVO4 layer, a 75 nm thick BiVO4 layer on WO3 being best performing.

Photoinduced electron transfer in WO3/BiVO4 heterojunction photoanodes: effects of the WO3 layer thickness.

The PEC performance of WO3/BiVO4 heterojunction photoanodes with a fixed BiVO4 thick top layer and different WO3 layer thicknesses was investigated under backside irradiation, in comparison with the performance of the same electrodes without a top BiVO4 layer. While the performance of these latter increase with increasing WO3 thickness, the presence of a BiVO4 layer, besides leading to an effective sensitization up to 520 nm, leads to a decrease of incident photon to current efficiency in the short wavelength's range. After having excluded major WO3 filter effects, this has been attributed to charge carrier recombination effects occurring when both oxides get excited and becoming more relevant with increasing WO3 thickness and decreasing excitation wavelength.

Effective Visible Light Exploitation by Copper Molybdo-tungstate Photoanodes.

The need for stable oxide-based semiconductors with a narrow band gap, able to maximize the exploitation of the visible light portion of the solar spectrum, is a challenging issue for photoelectrocatalytic (PEC) applications. In the present work, CuW1-x Mo x O4 (E g = 2.0 eV for x = 0.5), which exhibits a significantly reduced optical band gap E g compared with isostructural CuWO4 (E g = 2.3 eV), was investigated as a photoactive material for the preparation of photoanodes. CuW0.5Mo0.5O4 electrodes with different thicknesses (80-530 nm), prepared by a simple solution-based process in the form of multilayer films, effectively exhibit visible light photoactivity up to 650 nm (i.e., extended compared with CuWO4 photoanodes prepared by the same way). Furthermore, the systematic investigation on the effects on photoactivity of the CuW0.5Mo0.5O4 layer thickness evidenced that long-wavelength photons can better be exploited by thicker electrodes. PEC measurements in the presence of NaNO2, acting as a suitable hole scavenger ensuring enhanced photocurrent generation compared with that of water oxidation while minimizing dark currents, allowed us to elucidate the role that molybdenum incorporation plays on the charge separation efficiency in the bulk and on the charge injection efficiency at the photoanode surface. The adopted Mo for W substitution increases the visible light photoactivity of copper tungstate toward improved exploitation and storage of visible light into chemical energy via photoelectrocatalysis.

Copper-Modified TiO2 and ZrTiO4: Cu Oxidation State Evolution during Photocatalytic Hydrogen Production.

In the present work, two H2 evolution photocatalysts were prepared by employing two different oxides, TiO2 and zirconium titanate (ZrTiO4), as the support of various copper phases. For both the supports the same Cu loading (0.5% w/w) was adopted, but two different impregnation procedures have been followed, leading to different forms of Cu in the final composite material that are: (i) Cu(II) species dispersed on the oxide surface and (ii) Cu2O particles dispersed on the oxide surface. The present paper based on the parallel use of photocatalytic test and spectroscopic analysis performed in catalytic conditions illustrates the evolution of photocatalytic systems occurring during the H2 evolution reaction tests, pointing out that the as-prepared materials represent a pre-catalyst and they are modified during irradiation leading to the real working systems different from the starting ones. The herein presented spectroscopic analysis aims to contribute to the living debate on the oxidation state of copper in mixed Cu/oxide materials and on its role in hydrogen evolution under photocatalytic conditions.

Unraveling the Multiple Effects Originating the Increased Oxidative Photoactivity of {001}-Facet Enriched Anatase TiO2.

Crystal shape control on a series of anatase photocatalysts was achieved by varying the amount of HF employed as a capping agent in their hydrothermal synthesis. A systematic comparison between their physicochemical properties, determined by several complementary surface and bulk techniques before and after thermal treatment at 500 °C, allowed one to discern the influence of the relative amount of exposed {001} crystal facets among a series of effects simultaneously affecting their oxidative photocatalytic activity. The results of both formic acid and terephthalic acid photo-oxidation test reactions point to the primary role played by calcination in making {001} facets effectively photoactive. Annealing not only removes most of the residual fluorine capping agent from the photocatalyst surface, thus favoring substrate adsorption, but also produces morphological modifications to a crystal packing that makes accessible a larger portion of surface {001} facets due to the unpiling of platelike crystals. The photocatalyst bearing the highest amount of exposed {001} facets (60%) shows the highest photoactivity in both the direct and the (•)OH-radical-mediated photocatalytic test reaction.

Cr(VI) photocatalytic reduction: effects of simultaneous organics oxidation and of gold nanoparticles photodeposition on TiO2.

Commercial TiO(2) samples with different phase composition and surface area were tested as photocatalysts in the photoinduced reduction of Cr(VI) in aqueous suspensions at pH 3.7 under UV-visible light irradiation. This reaction was also coupled with the simultaneous photocatalytic oxidation of the pollutant azo dye Acid Orange 8 (AO8) and of formic acid, acting as hole scavengers. The co-presence of oxidizable and reducible species ensured better separation of photogenerated charge carriers, resulting in a higher rate of both organics' oxidation and Cr(VI) reduction, especially in the case of high surface area anatase TiO(2), having the strongest affinity for Cr(VI) and AO8, as demonstrated by competitive adsorption tests. The effects on Cr(VI) photocatalytic reduction of gold nanoparticles photodeposited on TiO(2) and of the Au loading were also investigated, aiming at ascertaining if this noble metal plays a role in the electron transfer processes involved in Cr(VI) reduction.

Effects of gold nanoparticles deposition on the photocatalytic activity of titanium dioxide under visible light.

The effects of gold nanoparticles deposited on titanium dioxide on the photocatalytic oxidative degradation of two organic substrates, i.e. formic acid and the azo dye Acid Red 1, and on the parallel O(2) reduction yielding hydrogen peroxide have been investigated under visible light irradiation. The method employed to reduce Au(iii) to metallic gold in the preparation of Au/TiO(2) photocatalysts was found to affect their photoactivity, also by modifying the properties of TiO(2). The presence of gold on TiO(2) facilitates both the electron transfer to O(2) and the mineralization of formic acid, which mainly proceeds through direct interaction with photoproduced valence band holes. The so-formed highly reductant CO(2)*(-) intermediate species may contribute in maintaining gold in metallic form. The controversial results obtained in the photocatalytic degradation of the dye were rationalised by taking into account that with this substrate, which mainly undergoes oxidation through a hydroxyl radical mediated mechanism, the photogenerated holes may partly oxidise gold nanoparticles, which consequently act as recombination centres of photoproduced charge carriers.