SARS-CoV-2 in environmental perspective: Occurrence, persistence, surveillance, inactivation and challenges.

The unprecedented global spread of the severe acute respiratory syndrome (SARS) caused by SARS-CoV-2 is depicting the distressing pandemic consequence on human health, economy as well as ecosystem services. So far novel coronavirus (CoV) outbreaks were associated with SARS-CoV-2 (2019), middle east respiratory syndrome coronavirus (MERS-CoV, 2012), and SARS-CoV-1 (2003) events. CoV relates to the enveloped family of Betacoronavirus (ßCoV) with positive-sense single-stranded RNA (+ssRNA). Knowing well the persistence, transmission, and spread of SARS-CoV-2 through proximity, the faecal-oral route is now emerging as a major environmental concern to community transmission. The replication and persistence of CoV in the gastrointestinal (GI) tract and shedding through stools is indicating a potential transmission route to the environment settings. Despite of the evidence, based on fewer reports on SARS-CoV-2 occurrence and persistence in wastewater/sewage/water, the transmission of the infective virus to the community is yet to be established. In this realm, this communication attempted to review the possible influx route of the enteric enveloped viral transmission in the environmental settings with reference to its occurrence, persistence, detection, and inactivation based on the published literature so far. The possibilities of airborne transmission through enteric virus-laden aerosols, environmental factors that may influence the viral transmission, and disinfection methods (conventional and emerging) as well as the inactivation mechanism with reference to the enveloped virus were reviewed. The need for wastewater epidemiology (WBE) studies for surveillance as well as for early warning signal was elaborated. This communication will provide a basis to understand the SARS-CoV-2 as well as other viruses in the context of the environmental engineering perspective to design effective strategies to counter the enteric virus transmission and also serves as a working paper for researchers, policy makers and regulators.

Sustainable consideration for traditional textile handloom cluster/village in pollution abatement - A case study.

Decentralized handlooms are being traditionally practised throughout India. Siripuram village known for traditional Pochampally/Ikat work was considered as a case study for detailed investigation towards providing a sustainable solution. Nearly 65% of village population solely depend on weaving and dyeing works as primary occupation based on the household survey and generated wash water of 127 KLD on an average from the dyeing operations. Initially, a topographical survey (Aerial drone; PHANTOM 4 RTK UAV) was carried out to understand the drainage pattern, elevations, contours and interlinked with domestic and dyeing functions. The characteristics of combined wastewater and dye wash water were studied at lab scale using sequential batch (SBR) operation under aerobic (SBRAe) and aerobic-anoxic (SBRAex) microenvironments. SBRAex microenvironment showed effective organic and nutrients removal due to infused anoxic microenvironment. Treatment studies depicted 76.2% of organic fraction, 73.3% of phosphate, and 81.6% of nitrate removal. Based on the lab scale studies a closed-loop decentralized effluent treatment system was designed to ensure zero-liquid discharge (ZLD).

Duckweed biorefinery - Potential to remediate dairy wastewater in integration with microbial protein production.

The phytoremediation potential of Duckweed in treating dairy wastewater (DWW) was studied, focusing on its utilization as nutritional biomass. The process resulted in good treatment efficiency with removal of organic carbon of 74% (COD), nitrates of 66% and phosphates of 80%. The increase in duckweed fronds with time was observed (doubling time (DT) - 0.87) resulting in an overall dry weight of 3.73 g. The lentils showed 58% of protein, 29.5% of carbohydrate (with 20% of starch), 15.6% of lipid (FAME-29.3%-saturated, 40.7%-mono- and 30%-poly-unsaturated fatty acids) and good amino acid content (34.04% essential and 65.92% non-essential). The biomass hydrolysate (mild acid pretreated) served as a substrate for microbial protein (MP) production using Bacillus subtilis, resulting in 60% of protein (0.57 g protein/g COD consumed; 0.63 g protein/g N consumed) and 21% of carbohydrate. The duckweed biomass offers multiple benefits including nutritional supplement in food/feed for livestock and poultry industries along with concurrent wastewater treatment as well serves as potential feedstock for biorefinery.

Longitudinal and Long-Term Wastewater Surveillance for COVID-19: Infection Dynamics and Zoning of Urban Community.

Wastewater-based epidemiology (WBE) is emerging as a potential approach to study the infection dynamics of SARS-CoV-2 at a community level. Periodic sewage surveillance can act as an indicative tool to predict the early surge of pandemic within the community and understand the dynamics of infection and, thereby, facilitates for proper healthcare management. In this study, we performed a long-term epidemiological surveillance to assess the SARS-CoV-2 spread in domestic sewage over one year (July 2020 to August 2021) by adopting longitudinal sampling to represent a selected community (~2.5 lakhs population). Results indicated temporal dynamics in the viral load. A consistent amount of viral load was observed during the months from July 2020 to November 2020, suggesting a higher spread of the viral infection among the community, followed by a decrease in the subsequent two months (December 2020 and January 2021). A marginal increase was observed during February 2021, hinting at the onset of the second wave (from March 2021) that reached it speak in April 2021. Dynamics of the community infection rates were calculated based on the viral gene copies to assess the severity of COVID-19 spread. With the ability to predict the infection spread, longitudinal WBE studies also offer the prospect of zoning specific areas based on the infection rates. Zoning of the selected community based on the infection rates assists health management to plan and manage the infection in an effective way. WBE promotes clinical inspection with simultaneous disease detection and management, in addition to an advance warning signal to anticipate outbreaks, with respect to the slated community/zones, to tackle, prepare for and manage the pandemic.

Defining the methodological approach for wastewater-based epidemiological studies-Surveillance of SARS-CoV-2.

Since COVID-19 outbreak, wastewater-based epidemiology (WBE) studies as surveillance system is becoming an emerging interest due to its functional advantage as a tool for early warning signal and to catalyze effective disease management strategies based on the community diagnosis. An attempt was made in this study to define and establish a methodological approach for conducting WBE studies in the framework of identifying/selection of surveillance sites, standardizing sampling policy, designing sampling protocols to improve sensitivity, adopting safety protocol, and interpreting the data. Data from hourly sampling indicated a peak in the viral RNA during the morning hours (6-9 am) when the all the domestic activities are maximum. The daily sampling and processing revealed the dynamic nature of infection spread among the population. The two sampling methods viz. grab, and composite showed a good correlation. Overall, this study establishes a structured protocol for performing WBE studies that could provide useful insights on the spread of the pandemic at a given point of time. Moreover, this framework could be extrapolated to monitor several other clinically relevant diseases. Following these guidelines, it is possible to achieve measurable and reliable SARS-CoV-2 RNA concentrations in wastewater infrastructure and therefore, provides a methodological basis for the establishment of a national surveillance system.

Corrigendum to "Defining the methodological approach for wastewater-based epidemiological studies-Surveillance of SARS-CoV-2" [Environ. Technol. Innov. 23 (2021) 101696].

[This corrects the article DOI: 10.1016/j.eti.2021.101696.].

Surveillance of SARS-CoV-2 spread using wastewater-based epidemiology: Comprehensive study.

SARS-CoV-2 pandemic is having a devastating effect on human lives. Recent reports have shown that majority of the individuals recovered from COVID-19 have serious health complications, which is going to be a huge economic burden globally. Given the wide-spread transmission of SARS-CoV-2 it is almost impossible to test every individual in densely populated countries. Recent reports have shown that sewage-based surveillance can be used as holistic approach to understand the spread of the pandemic within a population or area. Here we have estimated the spread of SARS-CoV-2 in the city of Hyderabad, India, which is a home for nearly 10 million people. The sewage samples were collected from all the major sewage treatment plants (STPs) and were processed for detecting the viral genome using the standard Reverse Transcription Polymerase Chain Reaction (RT-PCR) method. Interestingly, inlet samples of STPs were positive for SARS-CoV-2, while the outlets were negative, which indicates that the standard sewage treatment methods are efficient in eliminating the SARS-CoV-2 viral particles. Based on the detected viral gene copies per litre and viral particle shedding per individual, the total number of individuals exposed to SARS-CoV-2 was estimated. Through this study we suggest that sewage-based surveillance is an effective approach to study the infection dynamics, which helps in efficient management of the SARS-CoV-2 spread.

Anodic metabolic activity regulates the desalination efficiency in microbial catalysed electrochemical system.

Anodic metabolic rate showed regulatory influence on the desalination performance of microbial desalination cell (MDC) under open (OC) and closed circuit (CC) operations. In this study, three MDCs were tested for desalination with three different organic substrate loads 1500 ± 55 mg/L in MDC-A; 3500 ± 10 g/L in MDC-B; 4500 ± 12 g/L in MDC-C. Higher desalination and substrate removal rates were observed in CC than OC. Average desalination was MDC-C (51.4%-CC) > MDC-B (47.3%-CC) > MDC-A (45.3%-CC) and COD removal efficiencies were MDC-C (68.4%-CC) > MDC-B (64.4%-CC) > MDC-A (51.9%-CC). Increase in organic load resulted in higher desalination efficiency which was due to higher electrochemical and ionic gradient apart from anodic metabolic activity. The voltage and current density were observed to be maximum in MDC-C (685 mV; 2.16 mA/m2) followed by MDC-B (598 mV; 1.98 mA/m2) and MDC-A (501 mV; 1.76 mA/m2). This study demonstrated that the MDCs performance can be regulated by varying organic load and circuitry modes.

Self-induced bioelectro-potential influence on sulfate removal and desalination in microbial fuel cell.

This study focused on treatment of sulfate-rich produced water (PW) using microbial fuel cell (MFC) with biotic anode (bAC) and abiotic cathode (aCC) separated by a cation exchange membrane (CEM). MFC was operated under varied circuitry modes - open circuit (OC-without resistance) and closed circuit (CC-applied resistance (1kΩ)) to evaluate and assess the removal of sulfates and salts with simultaneous carbon utilization. The OC and CC operations depicted sulfates removal efficiency of 38% and 56%, salinity removal of 12% and 21% and COD removal of 47% and 58%, respectively. Both OC and CC showed K+ decrement in bAC and increment in aCC with a comparatively higher efficiency of ionic mobility in CC operation. Maximum open circuit voltage (OCV) of 498 mV (OC) was observed with redox catalytic peak currents from cyclic voltammetry [Anode/cathode, 3.5/-4.9 mA (OC); 6.9/-7.9 mA (CC)]. Dominance of Proteobacteria and Actinobacteria with specific enrichment of sulfate reducing bacteria (SRB) and halophiles was observed in bAC at the end of operation.

Concomitant use of Azolla derived bioelectrode as anode and hydrolysate as substrate for microbial fuel cell and electro-fermentation applications.

The potential of deoiled Azolla pinnata biomass (DAB) as electrode and substrate was evaluated for microbial fuel cell (MFC) operation. The anode electrode was fabricated using biochar obtained by subjecting DAB to pyrolysis at 600 °C, while the reducing sugars after hydrolysis of DAB by acid pretreatment was used as substrate. The post pyrolyzed biochar (P-DAB) was characterized for structural and elemental functionalities using SEM, XRD and Raman spectroscopy, whereas the reducing sugar obtained from hydrolyzed DAB (H-DAB) was analyzed for its composition. Experimental results indicated that at a given 3 g COD/L resulted in a voltage of 382 mV with 65.6% of COD reduction in closed circuit (CC) mode of operation. Cyclic voltammetric analysis depicted maximum oxidative and reductive peak currents of 3.42 mA and -4.0 mA. Noticeable peaks were also identified in CC (-0.2 V to +0.2 V and -0.19 V to -0.3 V) and OC (+0.2 V to +0.4 V and -0.1 V to -0.3 V) corresponding to complex IV cytochrome c couples (cytochrome Cox (Cyt Cox)/cytochrome Crd (Cyt Crd)), signifying the participation of electron carriers during electron transfer. The microbiome diversity showed dominance of Proteobacteria, a phylum known for exo-electrogenic bacterial species. The DAB-derived products account to environmental sustainability and support circular bioeconomy in a biorefinery mode.

Algal biorefinery models with self-sustainable closed loop approach: Trends and prospective for blue-bioeconomy.

Microalgae due to its metabolic versatility have received a focal attention in the biorefinery and bioeconomy context. Microalgae products have broad and promising application potential in the domain of renewable fuels/energy, nutraceutical, pharmaceuticals and cosmetics. Biorefining of microalgal biomass in a circular loop with an aim to maximize resource recovery is being considered as one of the sustainable option that will have both economical and environmental viability. The expansive scope of microalgae cultivation with self-sustainability approach was discussed in this communication in the framework of blue-bioeconomy. Microalgae based primary products, cultivation strategies, valorization of microalgae biomass for secondary products and integrated biorefinery models for the production of multi-based products were discussed. The need and prospect of self-sustainable models in closed loop format was also elaborated.

Deoiled algal biomass derived renewable sugars for bioethanol and biopolymer production in biorefinery framework.

The present study is designed to evaluate the potential of deoiled algal biomass (DAB) residue as an alternative resource for the production of bioethanol and biopolymers in a biorefinery approach. Hybrid pretreatment method resulted in higher sugar solubilization (0.590 g/g DAB) than the corresponding individual physicochemical (0.481 g/g DAB) and enzymatic methods (0.484 g/g DAB). Subsequent utilization of sugars from hybrid pretreatment for bioethanol using Saccharomyces cerevisiaeresulted in maximum bioethanol production at pH 5.5 (0.145 ±â€¯0.008 g/g DAB) followed by pH 5.0 (0.122 ±â€¯0.004 g/g DAB) and pH 6.0 (0.102 ±â€¯0.002 g/g DAB). The experiments for biopolymer (PHB: polyhydroxybutyrate) production resulted in 0.43 ±â€¯0.20 g PHB/g DCW. Extracted polymer on NMR and FT-IR analysis showed the presence of PHB. Exploration of DAB as an alternative renewable resource for multiple biobased products supports sustainability and also enables entirety use of DAB by addressing the DAB-residue allied disposal issues.

Microalgae-biorefinery with cascading resource recovery design associated to dairy wastewater treatment.

The potential of microalgae for the treatment of dairy wastewater (DWW) was studied by integrating with bioethanol production. At the end of treatment, organic carbon removal was observed to be 90% with simultaneous removal of nutrients. Biomass concentration increased from 3rd day and reached to a maximum of 1.4 g L-1 by the end of cycle. The biomolecular composition of microalgae comprised of 38% carbohydrates, 15% proteins and 22% lipids. Reducing sugars extracted from deoiled microalgae showed highest percentage of glucose (54.12%) than other monomers. The reducing sugars obtained were utilized for the production of bioethanol via yeast fermentation using Saccharomyces cerevisiae. This resulted in the production of ethanol (3G) upto 116.2 mg g-1 with simultaneous decrease in reducing sugars upto 92 mg g-1. The results obtained indicate potential of microalgae to produce multiple biobased products in a biorefinery framework.

Microbial mediated desalination for ground water softening with simultaneous power generation.

A novel three-chambered microbial desalination cell (MDC) was designed for evaluating desalination of synthetic ground water with simultaneous energy generation and resource recovery. The specific design enabled efficient interelectrode communication by reducing the distance of separation and also maintained an appropriate surface area to volume ratio. MDC were evaluated in different circuitry modes (open and closed) to assess the desalination efficiency, bioelectricity generation, resource recovery, substrate utilization and bioelectrokinetics. The closed circuit operation has showed efficient desalination efficiency (51.5%) and substrate utilization (70%). Owing to the effective electron transfer kinetics, closed circuit mode of operation showed effective desalination of the synthetic ground water with simultaneous power production (0.35W/m2). Circuitry specific biocatalyst activity was observed with higher peak currents (10.1mA; -5.98mA) in closed circuit mode. MDC can function as sustainable and alternative solution for ground and surface water treatment with power productivity and resource recovery.

Integrated ecotechnology approach towards treatment of complex wastewater with simultaneous bioenergy production.

Sequential integration of three stage diverse biological processes was studied by exploiting the individual process advantage towards enhanced treatment of complex chemical based wastewater. A successful attempt to integrate sequence batch reactor (SBR) with bioelectrochemical treatment (BET) and finally with microalgae treatment was studied. The sequential integration has showed individual substrate degradation (COD) of 55% in SBR, 49% in BET and 56% in microalgae, accounting for a consolidated treatment efficiency of 90%. Nitrates removal efficiency of 25% was observed in SBR, 31% in BET and 44% in microalgae, with a total efficiency of 72%. The SBR treated effluents fed to BET with the electrode intervention showed TDS removal. BET exhibited relatively higher process performance than SBR. The integration approach significantly overcame the individual process limitations along with value addition as biomass (1.75g/L), carbohydrates (640mg/g), lipids (15%) and bioelectricity. The study resulted in providing a strategy of combining SBR as pretreatment step to BET process and finally polishing with microalgae cultivation achieving the benefits of enhanced wastewater treatment along with value addition.

Regulatory effect of Fe-EDTA on mixotrophic cultivation of Chlorella sp. towards biomass growth and metabolite production.

The study examined the effect of varying concentrations of iron in the form of ethylene diamine tetra-acetic acid ferric sodium salt (Fe-EDTA) for cultivation of Chlorella sp. under mixotrophic condition to evaluate biomass growth and metabolites production. The experimental data depicted enhanced biomass production along with lipids, carbohydrates and proteins at an optimal iron concentration (8mg/L). Relatively higher biomass production (5.4g/L; 96h) with simultaneous total chlorophyll (5mg/mL (Chl a/b: 3.7/1.3mg/mL)), carbohydrates (105mg/g) and proteins (593mg/g) was observed with 8 mg/L Fe-EDTA. Total and neutral lipid content of 38% and 15.6% was observed under nutrient deprived conditions. The presence of iron showed distinct influence on the saturated fraction of FAME and increment in oleic acid (omega fatty acids; edible oil). Higher concentrations of Fe-EDTA (10/12mg/L) depicted incremental fraction of oleic acid.

Microalgae cultivation as tertiary unit operation for treatment of pharmaceutical wastewater associated with lipid production.

Microalgae based treatment was studied to polish sequential batch reactor (SBR) treated pharmaceutical wastewater under mixotrophic mode of operation with simultaneous biomass/lipid production. At the end of biomass growth phase (BGP), carbon removal efficiency was observed to be 73% along with good removal of nitrates (62%). Since microalgae assimilate nutrients from wastewater for growth, an increment in total biomass productivity (2.8g/l) was observed. Subjecting to nutrient stress phase (NSP), total lipid content of 17.2% with neutral lipids of 6.2% was observed under light condition. Contrarily, dark condition depicted total lipid content of 15.8% with neutral lipids constituting 6.5%. The nutrient stress in combination with light showed marked influence on the profile of saturated and unsaturated fatty acids. Integration of microalgae cultivation improves environmental sustainability and enables greener routes of biofuels and value added products synthesis in a biorefinery approach.