PdMo bimetallene for oxygen reduction catalysis.

The efficient interconversion of chemicals and electricity through electrocatalytic processes is central to many renewable-energy initiatives. The sluggish kinetics of the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER)1-4 has long posed one of the biggest challenges in this field, and electrocatalysts based on expensive platinum-group metals are often required to improve the activity and durability of these reactions. The use of alloying5-7, surface strain8-11 and optimized coordination environments12 has resulted in platinum-based nanocrystals that enable very high ORR activities in acidic media; however, improving the activity of this reaction in alkaline environments remains challenging because of the difficulty in achieving optimized oxygen binding strength on platinum-group metals in the presence of hydroxide. Here we show that PdMo bimetallene-a palladium-molybdenum alloy in the form of a highly curved and sub-nanometre-thick metal nanosheet-is an efficient and stable electrocatalyst for the ORR and the OER in alkaline electrolytes, and shows promising performance as a cathode in Zn-air and Li-air batteries. The thin-sheet structure of PdMo bimetallene enables a large electrochemically active surface area (138.7 square metres per gram of palladium) as well as high atomic utilization, resulting in a mass activity towards the ORR of 16.37 amperes per milligram of palladium at 0.9 volts versus the reversible hydrogen electrode in alkaline electrolytes. This mass activity is 78 times and 327 times higher than those of commercial Pt/C and Pd/C catalysts, respectively, and shows little decay after 30,000 potential cycles. Density functional theory calculations reveal that the alloying effect, the strain effect due to the curved geometry, and the quantum size effect due to the thinness of the sheets tune the electronic structure of the system for optimized oxygen binding. Given the properties and the structure-activity relationships of PdMo metallene, we suggest that other metallene materials could show great promise in energy electrocatalysis.

Composition-dependent ordering transformations in Pt-Fe nanoalloys.

SignificanceDynamically understanding the microscopic processes governing ordering transformations has rarely been attained. The situation becomes even more challenging for nanoscale alloys, where the significantly increased surface-area-to-volume ratio not only opens up a variety of additional freedoms to initiate an ordering transformation but also allows for kinetic interplay between the surface and bulk due to their close proximity. We provide direct evidence of the microscopic processes controlling the ordering transformation through the surface-bulk interplay in Pt-Fe nanoalloys and new features rendered by variations in alloy composition and chemical stimuli. These results provide a mechanistic detail of ordering transformation phenomena which are widely relevant to nanoalloys as chemical ordering occurs in most multicomponent materials under suitable environmental bias.

Solvent-Mediated, Reversible Ternary Graphite Intercalation Compounds for Extreme-Condition Li-Ion Batteries.

Traditional Li-ion intercalation chemistry into graphite anodes exclusively utilizes the cointercalation-free or cointercalation mechanism. The latter mechanism is based on ternary graphite intercalation compounds (t-GICs), where glyme solvents were explored and proved to deliver unsatisfactory cyclability in LIBs. Herein, we report a novel intercalation mechanism, that is, in situ synthesis of t-GIC in the tetrahydrofuran (THF) electrolyte via a spontaneous, controllable reaction between binary-GIC (b-GIC) and free THF molecules during initial graphite lithiation. The spontaneous transformation from b-GIC to t-GIC, which is different from conventional cointercalation chemistry, is characterized and quantified via operando synchrotron X-ray and electrochemical analyses. The resulting t-GIC chemistry obviates the necessity for complete Li-ion desolvation, facilitating rapid kinetics and synchronous charge/discharge of graphite particles, even under high current densities. Consequently, the graphite anode demonstrates unprecedented fast charging (1 min), dendrite-free low-temperature performance, and ultralong lifetimes exceeding 10 000 cycles. Full cells coupled with a layered cathode display remarkable cycling stability upon a 15 min charging and excellent rate capability even at -40 °C. Furthermore, our chemical strategies are shown to extend beyond Li-ion batteries to encompass Na-ion and K-ion batteries, underscoring their broad applicability. Our work contributes to the advancement of graphite intercalation chemistry and presents a low-cost, adaptable approach for achieving fast-charging and low-temperature batteries.

Design and Development of Stable Nanocrystalline High-Entropy Alloy: Coupling Self-Stabilization and Solute Grain Boundary Segregation Effects.

Grain growth is prevalent in nanocrystalline (NC) materials at low homologous temperatures. Solute element addition is used to offset excess energy that drives coarsening at grain boundaries (GBs), albeit mostly for simple binary alloys. This thermodynamic approach is considered complicated in multi-component alloy systems due to complex pairwise interactions among alloying elements. Guided by empirical and GB-segregation enthalpy considerations for binary-alloy systems, a novel alloy design strategy, the "pseudo-binary thermodynamic" approach, for stabilizing NC-high entropy alloys (HEAs) and other multi-component-alloy variants is proposed. Using Al25Co25Cr25Fe25 as a model-HEA to validate this approach, Zr, Sc, and Hf, are identified as the preferred solutes that would segregate to HEA-GBs to stabilize it against growth. Using Zr, NC-Al25Co25Cr25Fe25 HEAs with minor additions of Zr are synthesized, followed by annealing up to 1123 K. Using advanced characterization techniques- in situ X-ray diffraction (XRD), scanning/transmission electron microscopy (S/TEM), and atom probe tomography, nanograin stability due to coupling self-stabilization and solute-GB segregation effects is reported in HEAs up to substantially high temperatures. The self-stabilization effect originates from the preferential GB-segregation of constituent HEA-elements that stabilizes NC-Al25Co25Cr25Fe25 up to 0.5Tm (Tm-melting temperature). Meanwhile, solute-GB segregation originates from Zr segregation to NC-Al25Co25Cr25Fe25 GBs; this results in further stabilization of the phase and grain-size (≈14 nm) up to ≈0.58 and ≈0.64Tm, respectively.

Hypoxia-induced ELF3 promotes tumor angiogenesis through IGF1/IGF1R.

Epithelial ovarian cancer (EOC) is one of the most lethal gynecological cancers despite a relatively low incidence. Angiogenesis, one of the hallmarks of cancer, is essential for the pathogenesis of EOC, which is related to the induction of angiogenic factors. We found that ELF3 was highly expressed in EOCs under hypoxia and functioned as a transcription factor for IGF1. The ELF3-mediated increase in the secretion of IGF1 and VEGF promoted endothelial cell proliferation, migration, and EOC angiogenesis. Although this situation was much exaggerated under hypoxia, ELF3 silencing under hypoxia significantly attenuated angiogenic activity in endothelial cells by reducing the expression and secretion of IGF1 and VEGF. ELF3 silencing attenuated angiogenesis and tumorigenesis in ex vivo and xenograft mouse models. Consequently, ELF3 plays an important role in the induction of angiogenesis and tumorigenesis in EOC as a transcription factor of IGF1. A detailed understanding of the biological mechanism of ELF3 may both improve current antiangiogenic therapies and have anticancer effects for EOC.

Converting Carbon Dioxide into Carbon Nanotubes by Reacting with Ethane.

The urgency to mitigate environmental impacts from anthropogenic CO2 emissions has propelled extensive research efforts on CO2 reduction. The current work reports a novel approach involving transforming CO2 and ethane into carbon nanotubes (CNTs) using earth-abundant metals (Fe, Co, Ni) at 750 °C. This route facilitates long-term carbon storage via generating high-value CNTs and produces valuable syngas with adjustable H2/CO ratios as byproducts. Without CO2, direct pyrolysis of ethane undergoes rapid deactivation. The participation of CO2 not only enhances the durability of the catalyst, but also contributes about 30 % of the CNTs production, presenting a viable solution to CO2 challenges. The CNT morphology depends on the catalyst used. Co- and Ni-based catalysts produce CNT with a 20 nm diameter and micrometer length, whereas Fe-based catalysts yield bamboo-like structures. This work represents a pioneering effort in utilizing CO2 and ethane for CNT production with potential environmental and economic benefits.

Identification and Catalysis of the Potential-Limiting Step in Lithium-Sulfur Batteries.

The Li-S chemistry is thermodynamically promising for high-density energy storage but kinetically challenging. Over the past few years, many catalyst materials have been developed to improve the performance of Li-S batteries and their catalytic role has been increasingly accepted. However, the classic catalytic behavior, i.e., reduction of reaction barrier, has not been clearly observed. Crucial mechanistic questions, including what specific step is limiting the reaction rate, whether/how it can be catalyzed, and how the catalysis is sustained after the catalyst surface is covered by solid products, remain unanswered. Herein, we report the first identification of the potential-limiting step of Li-S batteries operating under lean electrolyte conditions and its catalysis that conforms to classic catalysis principles, where the catalyst lowers the kinetic barrier of the potential-limiting step and accelerates the reaction without affecting the product composition. After carefully examining the electrochemistry under lean electrolyte conditions, we update the pathway of the Li-S battery reaction: S8 solid is first reduced to Li2S8 and Li2S4 molecular species sequentially; the following reduction of Li2S4 to a Li2S2-Li2S solid with an almost constant ratio of 1:4 is the potential-limiting step; the previously believed Li2S2-to-Li2S solid-solid conversion does not occur; and the recharging reaction is relatively fast. We further demonstrate that supported cobalt phthalocyanine molecules can effectively catalyze the potential-limiting step. After Li2S2/Li2S buries the active sites, it can self-catalyze the reaction and continue driving the discharging process.

Atomistic Origins of Reversible Noncatalytic Gas-Solid Interfacial Reactions.

Noncatalytic gas-solid reactions are a large group of heterogeneous reactions that are usually assumed to occur irreversibly because of the strong driving force to favor the forward direction toward the product formation. Using the example of Ni oxidation into NiO with CO2, herein, we demonstrate the existence of the reverse element that results in the NiO reduction from the countering effect of the gaseous product of CO. Using in situ electron microscopy observations and atomistic modeling, we show that the oxidation process occurs via preferential CO2 adsorption along step edges that results in step-flow growth of NiO layers, and the presence of Ni atoms on the flat NiO surface promotes the nucleation of NiO layers. Simultaneously, the NiO reduction happens via preferential step-edge adsorption of CO that leads to the receding motion of atomic steps, and the presence of Ni vacancies in the NiO surface facilitates the CO-adsorption-induced surface pitting. Temperature and CO2 pressure effect maps are constructed to illustrate the spatiotemporal dynamics of the competing NiO redox reactions. These results demonstrate the rich gas-solid surface reaction dynamics induced by the coexisting forward and reverse reaction elements and have practical applicability in manipulating gas-solid reactions via controlling the gas environment or atomic structure of the solid surface to steer the reaction toward the desired direction.

Reversible Switch in Charge Storage Enabled by Selective Ion Transport in Solid Electrolyte Interphase.

Solid-electrolyte interphases (SEIs) in advanced rechargeable batteries ensure reversible electrode reactions at extreme potentials beyond the thermodynamic stability limits of electrolytes by insulating electrons while allowing the transport of working ions. Such selective ion transport occurs naturally in biological cell membranes as a ubiquitous prerequisite of many life processes and a foundation of biodiversity. In addition, cell membranes can selectively open and close the ion channels in response to external stimuli (e.g., electrical, chemical, mechanical, and thermal), giving rise to "gating" mechanisms that help manage intracellular reactions. We wondered whether the chemistry and structure of SEIs can mimic those of cell membranes, such that ion gating can be replicated. That is, can SEIs realize a reversible switching between two electrochemical behaviors, i.e., the ion intercalation chemistry of batteries and the ion adsorption of capacitors? Herein, we report such SEIs that result in thermally activated selective ion transport. The function of open/close gate switches is governed by the chemical and structural dynamics of SEIs under different thermal conditions, with precise behaviors as conducting and insulating interphases that enable battery and capacitive processes within a finite temperature window. Such an ion gating function is synergistically contributed by Arrhenius-activated ion transport and SEI dissolution/regrowth. Following the understanding of this new mechanism, we then develop an electrochemical method to heal the SEI layer in situ. The knowledge acquired in this work reveals the possibility of hitherto unknown biomimetic properties of SEIs, which will guide us to leverage such complexities to design better SEIs for future battery chemistries.

Regulating Catalytic Properties and Thermal Stability of Pt and PtCo Intermetallic Fuel-Cell Catalysts via Strong Coupling Effects between Single-Metal Site-Rich Carbon and Pt.

Developing low platinum-group-metal (PGM) catalysts for the oxygen reduction reaction (ORR) in proton-exchange membrane fuel cells (PEMFCs) for heavy-duty vehicles (HDVs) remains a great challenge due to the highly demanded power density and long-term durability. This work explores the possible synergistic effect between single Mn site-rich carbon (MnSA-NC) and Pt nanoparticles, aiming to improve intrinsic activity and stability of PGM catalysts. Density functional theory (DFT) calculations predicted a strong coupling effect between Pt and MnN4 sites in the carbon support, strengthening their interactions to immobilize Pt nanoparticles during the ORR. The adjacent MnN4 sites weaken oxygen adsorption at Pt to enhance intrinsic activity. Well-dispersed Pt (2.1 nm) and ordered L12-Pt3Co nanoparticles (3.3 nm) were retained on the MnSA-NC support after indispensable high-temperature annealing up to 800 °C, suggesting enhanced thermal stability. Both PGM catalysts were thoroughly studied in membrane electrode assemblies (MEAs), showing compelling performance and durability. The Pt@MnSA-NC catalyst achieved a mass activity (MA) of 0.63 A mgPt-1 at 0.9 ViR-free and maintained 78% of its initial performance after a 30,000-cycle accelerated stress test (AST). The L12-Pt3Co@MnSA-NC catalyst accomplished a much higher MA of 0.91 A mgPt-1 and a current density of 1.63 A cm-2 at 0.7 V under traditional light-duty vehicle (LDV) H2-air conditions (150 kPaabs and 0.10 mgPt cm-2). Furthermore, the same catalyst in an HDV MEA (250 kPaabs and 0.20 mgPt cm-2) delivered 1.75 A cm-2 at 0.7 V, only losing 18% performance after 90,000 cycles of the AST, demonstrating great potential to meet the DOE targets.

Enhancing Crystallization in Hybrid Perovskite Solar Cells Using Thermally Conductive 2D Boron Nitride Nanosheet Additive.

Controlling crystallization and grain growth is crucial for realizing highly efficient hybrid perovskite solar cells (PSCs). In this work, enhanced PSC photovoltaic performance and stability by accelerating perovskite crystallization and grain growth via 2D hexagonal boron nitride (hBN) nanosheet additives incorporated into the active perovskite layer are demonstrated. In situ X-ray scattering and infrared thermal imaging during the perovskite annealing process revealed the highly thermally conductive hBN nanosheets promoted the phase conversion and grain growth in the perovskite layer by facilitating a more rapid and spatially uniform temperature rise within the perovskite film. Complementary structural, physicochemical, and electrical characterizations further showed that the hBN nanosheets formed a physical barrier at the perovskite grain boundaries and the interfaces with charge transport layers, passivating defects, and retarding ion migration. As a result, the power conversion efficiency of the PSC is improved from 17.4% to 19.8%, along with enhanced device stability, retaining ≈90% of the initial efficiency even after 500 h ambient air storage. The results not only highlight 2D hBN as an effective additive for PSCs but also suggest enhanced thermal transport as one of the pathways for improved PSC performance by 2D material additives in general.

Stabilization of Dinuclear Rhodium and Iridium Clusters on Layered Titanate and Niobate Supports.

Atomically dispersed organometallic clusters can provide well-defined nuclearity of active sites for both fundamental studies as well as new regimes of activity and selectivity in chemical transformations. More recently, dinuclear clusters adsorbed onto solid surfaces have shown novel catalytic properties resulting from the synergistic effect of two metal centers to anchor different reactant species. Difficulty in synthesizing, stabilizing, and characterizing isolated atoms and clusters without agglomeration challenges allocating catalytic performance to atomic structure. Here, we explore the stability of dinuclear rhodium and iridium clusters adsorbed onto layered titanate and niobate supports using molecular precursors. Both systems maintain their nuclearity when characterized using aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). Statistical analysis of HAADF-STEM images revealed that rhodium and iridium dimers had mean cluster-to-cluster distances very similar to what is expected from a random distribution of atoms over a large area, indicating that they are dispersed without aggregation. The stability of dinuclear rhodium clusters supported on titanate nanosheets was also investigated by X-ray absorption fine structure (EXAFS), DRIFTS, and first-principles calculations. Both X-ray absorption spectroscopy and HAADF-STEM simulations, guided by density functional theory (DFT)-optimized structure models, suggested that rhodium dimers adsorb onto the nanosheets in an end-on binding mode that is stable up to 100 °C under reducing conditions. This study highlights that crystalline nanosheets derived from layered metal oxides can be used as model supports to selectively stabilize dinuclear clusters, which could have implications for heterogeneous catalysis.

Mitigating challenges in aberration-corrected electron-beam lithography on electron-opaque substrates.

Aberration-corrected electron-beam lithography (AC-EBL) using ultra-thin electron transparent membranes has achieved single-digit nanometer resolution in two widely used electron-beam resists: poly (methyl methacrylate) (PMMA) and hydrogen silsesquioxane. On the other hand, AC-EBL implementation on thick, electron-opaque substrates is appealing for conventional top-down fabrication of quantum devices with nanometer-scale features. To investigate the performance of AC-EBL on thick substrates, we measured the lithographic point spread function of a 200 keV aberration-corrected scanning transmission electron microscope by defining both positive and negative patterns in PMMA thin films, spin-cast on thick SiO2/Si substrates. We present the problems encountered during pre-exposure beam focusing and discuss methods to overcome them. In addition, applying some of these methods using commercial 50 nm thick SiNXmembranes with thick Si support frames, we printed arrays of holes in PMMA with pitches around 26 nm on SiNX/Si substrates with increasing Si thickness. Our results show that proximity effects from even 50 nm thick SiNXmembranes limit hole arrays to 20 nm pitch; however, down to this limit, the effect of the substrate thickness on the pattern quality is minimal. These results highlight the need for novel resists less susceptible to proximity effects, or resists which can be used directly, after development, as the dielectric material in periodic gates in 2D quantum devices.

Di-indenopyridines as topoisomerase II-selective anticancer agents: Design, synthesis, and structure-activity relationships.

Topoisomerases are key molecular enzymes responsible for altering DNA topology, thus they have long been considered as attractive targets for novel chemotherapeutic agents. Topoisomerase type II (Topo II) catalytic inhibitors embrace a fresh perspective meant to get beyond drawbacks caused by topo II poisons, such as cardiotoxicity and secondary malignancies. Based on previously reported 5H-indeno[1,2-b]pyridines, here we presented new twenty-three hybrid di-indenopyridines along with their topo I/IIα inhibitory and antiproliferative activity. Most of the prepared 11-phenyl-diindenopyridines showed negligible topo I inhibitory activity, showing selectivity over topo II. Among the series, we finally selected compound 17, which displayed 100 % topo IIα inhibition at 20 µM concentration and comparable antiproliferative activity against the tested cell lines. Through competitive EtBr displacement assay, cleavable complex assay, and comet assay, compound 17 was finally determined as a non-intercalative catalytic topo IIα inhibitor. The findings in this study highlight the significance of phenolic, halophenyl, thienyl, and furyl groups at the 4-position of the indane ring in the design and synthesis of di-indenopyridines as potent catalytic topo IIα inhibitors with remarkable anticancer effects.

Design, synthesis, and biological evaluation of novel HSP27 inhibitors to sensitize lung cancer cells to clinically available anticancer agents.

Expression of heat shock protein (HSP) correlates with the oncogenic status of malignant cells and plays an important role in tumorigenesis. HSP27 is constitutively expressed at specific stages of cancer development, and several clinical trials have reported correlations between HSP27 expression and tumor progression, metastasis, and chemoresistance in various types of cancer cells. These findings indicate that HSP27 is a major drug target, particularly in chemo-resistant cancers. As part of our ongoing efforts to improve the previously identified J2, a HSP27 cross-linker, we, in this study, report the identification of NK16 as a novel inducer of abnormal HSP27 dimers that did not affect the expression of HSP90 in an NCI-H460 lung cancer cell model. When NCI-H460 cells were treated with NK16 in combination with the anticancer drug cisplatin or paclitaxel, cleavage of PARP and caspase-3 was increased compared to administration of cisplatin or paclitaxel alone. Similar results were obtained in an NCI-H460-xenografted mouse model, in which tumor growth was suppressed more by co-administration of NK16 and paclitaxel than by paclitaxel alone. We propose NK16 as a meaningful strategy to improve the anticancer efficacy of cisplatin and paclitaxel.

Porosity Development at Li-Rich Layered Cathodes in All-Solid-State Battery during In Situ Delithiation.

Structural evolutions are crucial for determining the performance of high-voltage lithium, manganese-rich layered cathodes. Moreover, interface between electrode and electrolyte plays a critical role in governing ionic transfer in all-solid-state batteries. Here, we unveil two different types of porous structure in Li1.2Ni0.2Mn0.6O2 cathode with LiPON solid-state electrolyte. Nanopores are found near the cathode/electrolyte interface at pristine state, where cation mixing, phase transformation, oxygen loss, and Mn reduction are also found. In situ Li+ extraction induces the evolution of nanovoids, initially formed near the interface then propagated into the bulk. Despite the development of nanovoids, layered structure is conserved, suggesting the nature of nanopores and nanovoids are different and their impact would be divergent. This work demonstrates the intrinsic interfacial layer, as well as the dynamic scenario of nanovoid formation inside high-capacity layered cathode, which helps to understand the performance fading in cathodes and offers insight into the all-solid-state battery design.

Rapid Atomic Ordering Transformation toward Intermetallic Nanoparticles.

Chemically ordered intermetallic nanoparticles are promising candidates for energy-related applications such as electrocatalysis. However, the synthesis of intermetallics generally requires long annealing (several hours) to achieve the ordered structure, which causes nanoparticles agglomeration and diminished performance, particularly for catalysis. Herein, we demonstrate a new rapid Joule heating approach that can synthesize highly ordered and well-dispersed intermetallic nanoparticles. As a proof-of-concept, we synthesized fully ordered Pd3Pb intermetallic nanoparticles that feature small size distribution (∼6 nm). Computational analysis of the L12 Pd3Pb material suggests that this rapid atomic ordering transformation can be attributed to a vacancy-mediated diffusion mechanism. Moreover, the nanoparticles demonstrate excellent electrocatalytic activity and exceptional stability for the oxygen reduction reaction (ORR), retaining >95% of the current density over 10 h of chronoamperometry test with negligible structural and compositional changes. This study demonstrates a new strategy of providing a new direction for intermetallic synthesis and catalyst discovery.

Metal-Coordinated Phthalocyanines as Platform Molecules for Understanding Isolated Metal Sites in the Electrochemical Reduction of CO2.

Single-atom catalysts (SACs) of non-precious transition metals (TMs) often show unique electrochemical performance, including the electrochemical carbon dioxide reduction reaction (CO2RR). However, the inhomogeneity in their structures makes it difficult to directly compare SACs of different TM for their CO2RR activity, selectivity, and reaction mechanisms. In this study, the comparison of isolated TMs (Fe, Co, Ni, Cu, and Zn) is systematically investigated using a series of crystalline molecular catalysts, namely TM-coordinated phthalocyanines (TM-Pcs), to directly compare the intrinsic role of the TMs with identical local coordination environments on the CO2RR performance. The combined experimental measurements, in situ characterization, and density functional theory calculations of TM-Pc catalysts reveal a TM-dependent CO2RR activity and selectivity, with the free energy difference of ΔG(*HOCO) - ΔG(*CO) being identified as a descriptor for predicting the CO2RR performance.

Topoisomerase IIα inhibitory and antiproliferative activity of dihydroxylated 2,6-diphenyl-4-fluorophenylpyridines: Design, synthesis, and structure-activity relationships.

A new series of fifty-four 2-phenol-4-aryl-6-hydroxyphenylpyridines containing fluorophenyl, trifluoromethylphenyl, and trifluoromethoxy phenyl groups were synthesized and tested for topoisomerase IIα inhibitory and antiproliferative activity against different cancer cell lines in an attempt to look into topoisomerase IIα-targeted prospective anticancer agents to counter the limitations of available treatment options. When compared to positive controls, several compounds 11-12, 37, 50, and 51 showed high antiproliferative activity, while several 4-fluorophenyl substituted compounds 13-14 and 18 showed strong topoisomerase IIα inhibition. Surprisingly, most of the compounds had a significant antiproliferative effect on the HCT15 colorectal adenocarcinoma and T47D breast cancer cell lines. Moreover, compound 12 with para-fluorophenyl at the 4-position and meta-phenolic groups at the 2- and 6-positions inhibited proliferating HeLa cervix adenocarcinoma cells with an IC50 value of 1.28 µM. Based on biological results, the structure-activity relationships of the synthesized derivatives emphasized the significance of 4-trifluoromethoxyphenyl groups for strong antiproliferative activity and 4-fluorophenyl groups for strong topo IIα inhibition. Furthermore, meta- and para-phenolic groups at the 2- and 4-positions are favorable for strong topo IIα inhibitory and antiproliferative activity. The research findings provide insight into the effect of different fluorine functionalities in the discovery of novel topoisomerase IIα-targeted anticancer agents.

Atomically Dispersed Dual-Metal Site Catalysts for Enhanced CO2 Reduction: Mechanistic Insight into Active Site Structures.

Carbon-supported nitrogen-coordinated single-metal site catalysts (i.e., M-N-C, M: Fe, Co, or Ni) are active for the electrochemical CO2 reduction reaction (CO2 RR) to CO. Further improving their intrinsic activity and selectivity by tuning their N-M bond structures and coordination is limited. Herein, we expand the coordination environments of M-N-C catalysts by designing dual-metal active sites. The Ni-Fe catalyst exhibited the most efficient CO2RR activity and promising stability compared to other combinations. Advanced structural characterization and theoretical prediction suggest that the most active N-coordinated dual-metal site configurations are 2N-bridged (Fe-Ni)N6 , in which FeN4 and NiN4 moieties are shared with two N atoms. Two metals (i.e., Fe and Ni) in the dual-metal site likely generate a synergy to enable more optimal *COOH adsorption and *CO desorption than single-metal sites (FeN4 or NiN4 ) with improved intrinsic catalytic activity and selectivity.