Effect of resin composite shade on digital fiber-optic transillumination imaging in vitro.

Digital imaging fiber-optic transillumination (DIFOTI) devices have been used to detect caries, a technique without using X-rays. However, the effects of resin composites (RCs) shades on the images acquired with DIFOTI devices have not been investigated. Thus, this study aimed to elucidate the influence of RC shade on the images obtained with DIFOTI technique. Three shades (A1, A3, and Opaque) for each of four flowable RCs were filled on a cavity prepared in a left mandibular first premolar obtained from a donated body. Then, transmission images with a DIFOTI device (DIAGNOcam; KaVo, Biberach, Germany) were acquired, and the average lightness values of the images in the RC and enamel were used to calculate differences between those areas. To clarify the influence of the optical translucency and color on DIFOTI images, the color parameters (L*, a* and b*) of each RC were obtained with black and white backgrounds. The color differences between the backgrounds were calculated as transparency parameter (TP) values. The number of repetitions was set to 10. Differences in the lightness value of the shades varied in each RC. The difference in lightness was significantly associated with the TP value and color parameters of L* (p < 0.01), with negative (R = - 0.81) and positive (R = 0.84) correlations, respectively. In conclusion, DIFOTI images of RCs with high optical translucency resembled those of the natural tooth structure.

Efficacy of bisphosphonates in detection of early enamel caries using NIR fluorescence imaging and inhibition of caries progression.

NIR fluorescence imaging using bisphosphonate-Indocyanine green has been indicated for early interproximal caries detection. This study assessed diagnostic accuracy of caries detection by NIR fluorescence imaging with OsteoSense 750® (OS750) in vitro and ex vivo, and to analyze the therapeutic efficacy of a bisphosphonate (Etidronate) in inhibiting enamel caries progression in vitro. Methods: Four experiments were conducted using extracted human teeth; 1) to calculate the infiltration rate of OS750 into interproximal white spot lesions using fluorescence microscope, 2) to assess diagnostic accuracy of interproximal natural white spot lesions using desktop NIR fluorescence imaging device in vitro setting, 3) to assess diagnostic accuracy of artificially created deeper enamel carious lesion (0.5 mm~1.0 mm) using NIR fluorescence image through the head-mount display in ex vivo setting, 4) to compare the progression on the enamel caries lesions treated by Etidronate, NaF and distilled-water. Diagnostic accuracy was analyzed using sensitivity, specificity and receiver operating curves (ROC). The caries progression was calculated with micro-CT and was statistically analyzed using a two-way ANOVA and the Tukey HDS post-hoc test. Results: 1) The infiltration rate of OS750 was 101.83% ± 8.66 (Min: 90.10%, Max: 133.94%). 2) The average of sensitivity and specificity in vitro setting experiments were 86.7% ± 4.4% and 70% ± 11%, respectively. The average of area under the ROC curves (AUC) was 0.883 ± 0.059 indicating excellent performance. 3) The mean sensitivity and specificity in ex vivo setting was 82.97% ± 15% and 76.78% ± 13.27% respectively. 4) The carious lesion volume treated by Etidronate was significantly smaller at post treatment-1 (p<0.05) and treatment-2 (p<0.01) than the control. There was no significant difference in lesion volume in the Etidronate and NaF group at the time point of post treatment-1. Conclusion: This study suggests that bisphosphonates contribute to both early diagnosis of enamel caries and inhibition of caries progression.

Evaluation of the Influenza Risk Reduction from Antimicrobial Spray Application on Porous Surfaces.

Antimicrobial spray products are used by millions of people around the world for cleaning and disinfection of commonly touched surfaces. Influenza A is a pathogen of major concern, leading to up to 49,000 deaths and 114,000 hospitalizations per year in the United States alone. One of the recognized routes of transmission for influenza A is by transfer of viruses from surfaces to hands and subsequently to mucous membranes. Therefore, routine cleaning and disinfection of surfaces is an important part of the environmental management of influenza A. While the emphasis is generally on spraying hard surfaces and laundering cloth and linens with high temperature machine drying, not all surfaces can be treated in this manner. The quantitative microbial risk assessment (QMRA) approach was used to develop a stochastic risk model for estimating the risk of infection from indirect contact with porous fomite with and without surface treatment with an antimicrobial spray. The data collected from laboratory analysis combined with the risk model show that influenza A infection risk can be lowered by four logs after using an antimicrobial spray on a porous surface. Median risk associated with a single touch to a contaminated fabric was estimated to be 1.25 × 10-4 for the untreated surface, and 3.6 × 10-8 for the treated surface as a base case assumption. This single touch scenario was used to develop a generalizable model for estimating risks and comparing scenarios with and without treatment to more realistic multiple touch scenarios over time periods and with contact rates previously reported in the literature. The results of this study and understanding of product efficacy on risk reduction inform and broaden the range of risk management strategies for influenza A by demonstrating effective risk reduction associated with treating nonporous fomites that cannot be laundered at high temperatures.

Development of a rapid and reliable method to simultaneously detect seven food allergens in processed foods using LC-MS/MS.

Rapid analysis of multiple food allergens is required to confirm the appropriateness of food allergen labelling in processed foods. This study aimed to develop a rapid and reliable method to simultaneously detect trace amounts of seven food allergenic proteins (wheat, buckwheat, milk, egg, crustacean, peanut, and walnut) in processed foods using LC-MS/MS. Suspension-trapping (S-Trap) columns and on-line automated solid-phase extraction were used to improve the complex and time-consuming pretreatment process previously required for allergen analysis using LC-MS/MS. The developed method enabled the simultaneous detection of selected marker peptides for specific proteins derived from seven food ingredients in five types of incurred samples amended with trace amounts of allergenic proteins. The limit of detection values of the method for each protein were estimated to be <1 mg/kg. The developed analytical approach is considered an effective screening method for confirming food allergen labelling on a wide range of processed foods.

Influence of toothbrush abrasion on the surface characteristics of CAD/CAM composite resin blocks with shade gradations.

Crown restorations in anterior region are recommended highly color-reproductivity because of aesthetic reason. Composite resin block with several shade gradations is especially produced for anterior restorations. To clarify the durability of an aesthetic, the effect of toothbrush abrasion on surface properties was performed. Composite-resin blocks without shade gradation and a ceramic block were used as controls. All specimens were prepared using #2000 SiC paper and polished using an aluminum oxide polishing paste. Toothbrush abrasion tests were carried out for 20,000 cycles at a frequency of 2 Hz with 2.0 N load. Gloss and surface roughness were measured before and after toothbrush abrasion. The number of repetitions was set to five. It was clarified that tooth brushing caused to decrease in the gloss and to increase in the surface roughness with significant negative correlations between these results not only in composite-resin blocks without shade gradation but also in those with gradation.

The Effects of Different Molding Orientations, Highly Accelerated Aging, and Water Absorption on the Flexural Strength of Polyether Ether Ketone (PEEK) Fabricated by Fused Deposition Modeling.

Rising prices are currently a problem in the world. In particular, the abnormal increases in the price of metals, which are often used in dental prosthetics, have increased the burden of dental costs on the public. There is therefore an urgent need to develop prosthetic devices made from materials that are not affected by the global situation and that have excellent biocompatibility and mechanical properties comparable to those of metals. Polyether ether ketone (PEEK) is a promising alternative to metal in dentistry. This study compared the effects of different molding orientations, highly accelerated aging, and water absorption on the flexural strength of PEEK fabricated by fused deposition modeling (FDM) and examined its potential for dental applications. The flexural strength of PEEK stacked at 0° to the molding stage (0° PF), with and without highly accelerated aging, was significantly greater than for the other molding orientations. As with PD, the maximum test load for 0° PF was measured without fracture. PEEK stacked at 45° (45° PF) and 90° (90° PF) to the molding stage easily fractured, as the applied load pulled the stacked layers. No statistically significant difference was found between the flexural strength of 45° PF and 90° PF. The flexural strength decreased under all conditions due to defects in the crystal structure of PEEK caused by highly accelerated aging.

Mechanical and surface properties of additive manufactured zirconia under the different building directions.

PURPOSE: This study investigates the mechanical and surface properties of zirconia manufactured using additive manufacturing (AM) technology and the effect of the building direction on the mechanical and surface properties. METHODS: Specimens were prepared using ZrO2 paste (3DMix ZrO2; 3DCeram) and a three-dimensional printing system (CeraMaker 900; 3DCeram) based on the principles of stereolithography (SLA). The mechanical properties (flexural strength, Vickers hardness, fracture toughness, elastic modulus, and Poisson's ratio) and surface properties (chemical composition and surface observation) were evaluated for three building directions (parallel, diagonal, and perpendicular) to investigate the relationship between the building directions and the anisotropy of the mechanical and surface properties of SLA-manufactured zirconia. Statistical analysis was performed using a one-way analysis of variance and Tukey's honestly significant difference test. RESULTS: The highest flexural strength was obtained for a perpendicular building direction. The flexural strength was significantly higher in the perpendicular direction than in the parallel and diagonal directions; it was also significantly higher in the diagonal direction than in the parallel direction (P<0.05). The Vickers hardness, fracture toughness, elastic modulus, Poisson's ratio, and chemical composition did not differ significantly. Microstructural observations revealed that the layers, large crystals, and pores were more prominent in the parallel direction. CONCLUSIONS: The flexural strength and surface structure of the tested SLA-manufactured zirconia were influenced by the building direction; however, other mechanical properties remained unaffected. The layer boundaries affected the anisotropic behavior of the builds to a certain extent, owing to the layer-by-layer production method.

Physiological importance and role of Mg2+ in improving bacterial resistance to cesium.

Cesium (Cs) is an alkali metal with radioactive isotopes such as 137Cs and 134Cs. 137Cs, a product of uranium fission, has garnered attention as a radioactive contaminant. Radioactive contamination remediation using microorganisms has been the focus of numerous studies. We investigated the mechanism underlying Cs+ resistance in Microbacterium sp. TS-1 and other representative microorganisms, including Bacillus subtilis. The addition of Mg2+ effectively improved the Cs+ resistance of these microorganisms. When exposed to high concentrations of Cs+, the ribosomes of Cs+-sensitive mutants of TS-1 collapsed. Growth inhibition of B. subtilis in a high-concentration Cs+ environment was because of a drastic decrease in the intracellular potassium ion concentration and not the destabilization of the ribosomal complex. This is the first study demonstrating that the toxic effect of Cs+ on bacterial cells differs based on the presence of a Cs+ efflux mechanism. These results will aid in utilizing high-concentration Cs+-resistant microorganisms for radioactive contamination remediation in the future.

A magnesium transporter is involved in the cesium ion resistance of the high-concentration cesium ion-resistant bacterium Microbacterium sp. TS-1.

Cesium ion (Cs+) resistance has been reported in bacteria but is poorly understood as reports on Cs+-resistant bacteria have been limited. We previously reported a novel Cs+/H+ antiporter CshA implicated in Cs+-resistance in Microbacterium sp. TS-1. The present study used the same screening method to isolate novel Cs+-sensitive mutants and their revertants from TS-1. A comparative mutation site analysis using whole-genome sequencing revealed that MTS1_03028 encodes the Mg2+ transporter MgtE and is a candidate Cs+ resistance-related gene. We performed a bioinformatic analysis of MTS1_03028 and complementation experiments on Cs+ resistance in the TS-1 MTS1_03028 mutants Mut5 and Mut7 as well as Escherichia coli expressing MTS1_03028 in the presence of Mg2+. We established the role of MgtE in Cs+ resistance through a functional analysis of TS-1. Enhancing Mg2+ transport by expression of MTS_03028 conferred increased Cs+ resistance. When this strain was exposed to Cs+ concentrations exceeding 200 mM, CshA consistently lowered the intracellular Cs+ concentration. To our knowledge, the present study is the first to clarify the mechanism of Cs+ resistance in certain bacteria. The study findings offer important insights into the mechanism of bacterial resistance to excess Cs+ in the environment, suggesting the potential for bioremediation in high Cs-contaminated areas.

The effect of low-temperature degradation and building directions on the mechanical properties of additive-manufactured zirconia.

This study aimed to investigate the effect of low-temperature degradation (LTD) on the mechanical properties of additive-manufactured zirconia. In addition, the mechanical properties of additive-manufactured were compared with those before aging under similar experimental conditions. This study prepared stereolithography apparatus fabricated zirconia specimens with flexural strength, modulus of elasticity, Vickers hardness, and fracture toughness. The specimen position data were set as parallel (0°), diagonal (45°), and perpendicular (90°) to the direction of the building. The LTD condition was 5 h under 134ºC and 0.2 MPa in an autoclave. It was found that the 0° direction differed significantly from all other conditions before and after aging, and the highest flexural strength was obtained when the additive specimen was manufactured perpendicular to the building direction. However, the results indicate that there is a negligible effect of aging on the mechanical properties of additive-manufactured zirconia.

Impact of antibacterial detergent on used-towel microbiomes at species-level and its effect on malodor control.

The impact of antibacterial detergent on microbial exchanges and its subsequent effect on malodor in used towels were examined. Homogenization of microbiome among postwashed and indoor dried towels that was dominated by known malodor-producing bacteria. The microbial exchange was attenuated, and the abundance of malodor-producing bacteria was reduced in towels laundered with antibacterial detergent. Reduction of malodorous volatile organic compounds produced from towels laundered with antibacterial detergent.

Incidence of antiresorptive agent-related osteonecrosis of the jaw: A multicenter retrospective epidemiological study in Hyogo Prefecture, Japan.

Background/purpose: The incidence of medication-related osteonecrosis of the jaw is increasing worldwide, mostly due to the use of antiresorptive agents (ARAs) such as bisphosphonate (BP) and denosumab (Dmab). However, the proportion of BP-related osteonecrosis of the jaw (BRONJ) and Dmab-related osteonecrosis of the jaw (DRONJ) among all ARA-related osteonecrosis of the jaw (ARONJ) cases is not clear; this hinders appropriate treatment, recurrence-prevention planning, and avoidance of unnecessary Dmab withdrawal. Moreover, the causative drug administered at each disease stage remains unknown. Therefore, we conducted a retrospective study of patients with ARONJ who visited oral and maxillofacial surgery departments at hospitals in Hyogo Prefecture, Japan, over 3 years to classify and compare patient characteristics with those having BRONJ and DRONJ. We sought to identify the proportion of DRONJ in ARONJ. Materials and methods: After excluding stage 0 patients, 1021 patients were included (471 high-dose; 560 low-dose). ARA treatment for bone metastases of malignant tumors and multiple myeloma was considered high dose, while that for cancer treatment-induced bone loss and osteoporosis was low dose. Results: Low doses of BP and Dmab accounted for >50% patients; the results differed from those in other countries. DRONJ accounted for 58% and 35% of high-dose and low-dose cases, respectively. Stage 3 ARONJ cases comprised 92 (19.5%) low-dose BRONJ, 39 (20.1%) high-dose BRONJ, 24 (30%) low-dose DRONJ, and 68 (24.5%) high-dose DRONJ. Eighty-nine patients who received switch therapy were divided into BRONJ or DRONJ, but there was no difference in the ratio of each stage compared to the non-switch therapy. Conclusion: To the best of our knowledge, this is the first study to clarify the proportion of BRONJ and DRONJ cases, causative drug, and its doses by disease stages. DRONJ accounted for approximately 30% of the ARONJ, approximately 60% of which was due to high doses.

Application of fused deposition modeling technology for fabrication jigs of three-point bending test for dental composite resins.

This study aimed to clarify the application possibility of the fused deposition modeling (FDM) technology on the fabrication of jigs for a flexural test of dental composite resins (CRs). Three types of jigs were prepared to carry out three-point bending tests; 3D printed jig including support rollers, 3D printed jig with stainless-steel support rollers, and stainless-steel jig and stainless-steel support rollers. An FDM 3D printer with polylactic acid filament was used to produce 3D printed jigs. For evaluation of flexural strength, two types, packable and flowable, of composite resins were selected to prepare specimens. Three-point bending tests were performed using a universal testing machine. Then flexural strength and flexural elastic modulus were calculated. Specimen preparation and three-point bending test were conducted according to the ISO 4049:2019. All experiments were repeated 20 times. Flexural strength and flexural elastic modulus of packable CR were significantly larger than those of flowable. However, there were no significant differences among the jigs in both results. Consequently, FDM technology could be applied to fabricate jigs for the flexural test of CRs, and the mechanical properties could be evaluated as accurately as a stainless-steel jig.

Corrigendum: Novel Cesium Resistance Mechanism of Alkaliphilic Bacterium Isolated From Jumping Spider Ground Extract.

[This corrects the article DOI: 10.3389/fmicb.2022.841821.].

Novel Cesium Resistance Mechanism of Alkaliphilic Bacterium Isolated From Jumping Spider Ground Extract.

The radionuclide isotopes (134Cs and 137Cs) of Cesium (Cs), an alkali metal, are attracting attention as major causes of radioactive contamination. Although Cs+ is harmful to the growth of plants and bacteria, alkaliphilic bacterium Microbacterium sp. TS-1, isolated from a jumping spider, showed growth even in the presence of 1.2 M CsCl. The maximum concentration of Cs+ that microorganisms can withstand has been reported to be 700 mM till date, suggesting that the strain TS-1 is resistant to a high concentration of Cs ions. Multiple reports of cesium ion-resistant bacteria have been reported, but the detailed mechanism has not yet been elucidated. We obtained Cs ion-sensitive mutants and their revertant mutants from strain TS-1 and identified a Cs ion resistance-related gene, MTS1_00475, by performing SNP analysis of the whole-genome sequence data. When exposed to more than 200 mM Cs+ concentration, the intracellular Cs+ concentration was constantly lowered by MTS1_00475, which encodes the novel low-affinity Cs+/H+ antiporter. This study is the first to clarify the mechanism of cesium resistance in unexplained cesium-resistant microorganisms. By clarifying the new cesium resistance mechanism, it can be expected to be used as a bioremediation tool for treating radioactive Cs+ contaminated water.

Current Implementation of Digital Dentistry for Removable Prosthodontics in US Dental Schools.

Objectives: Although digital technology has been widely integrated into dental education, there is limited literature investigating the extent of the integration of computer-aided design and computer-aided manufacturing (CAD-CAM) for removable systems in the dental curriculum. The purpose of this study was to assess the current implementation of CAD-CAM complete and partial dentures in predoctoral (PP) and advanced graduate prosthodontic (AGP) education in US dental schools. The study also aimed to identify potential barriers to its implementation in the dental curriculum. Methods: An online survey with 15 questions was created using online survey software. The survey was distributed to the directors of predoctoral prosthodontics in 56 schools and advanced graduate programs of prosthodontics in 52 schools listed in the 2018-19 American Dental Education Association (ADEA) Directory. Results: The percentage of programs (PP and AGP) implementing CAD-CAM complete dentures (CAD-CAM CDs) and CAD-CAM removable partial dentures (CAD-CAM RPDs) in their didactic, preclinical, and clinical curricula was recorded. CAD-CAM CDs are taught in didactic courses in 54.2% of PP and 65.2% of AGP. However, CAD-CAM RPDs are only taught in 37.5% of PP and 47.8% of AGP. Programs are largely limited by a lack of funds, resources, time, and faculty members. Conclusion: While digital technologies have indeed become more prevalent in dental education, many institutions face barriers to implementation. More research must be conducted in order to support the continued incorporation of digital technologies into dental education.

Importance of bitewing radiographs for the early detection of interproximal carious lesions and the impact on healthcare expenditure in Japan.

BACKGROUND: Globally, the direct cost of dental caries is approximately $298B yearly, consuming 5-10% of national healthcare budgets. Bitewing radiographs (BWR) are the standard method of diagnosing interproximal dental caries. In Japan, bitewing radiographs are rarely used. This retrospective observational study was conducted to measure the potential economic impact of carious lesions left undiagnosed and untreated due to this omission of bitewing radiographs. METHODS: The total number of existing carious lesions, the number of undiagnosed lesions, and costs of treating these lesions were calculated from the national database of Ministry of Health, Labor and Wellness in Japan between June 2013 and 2017. The number of affected teeth was estimated using prevalence data and undiagnosed lesions were estimated. The expense associated with treating progressed lesions was calculated using the standard Japanese fee structure. BWR trends were assessed, and analyses were performed to understand the differences between states and populations over time. RESULTS: The average number of BWR taken monthly per office was 48.3±1.1 (average ± SD). It was calculated that an average of 6,429,155 lesions went undiagnosed per month, 93.5 teeth per practice, and 1.6 teeth per patient. The cost of treating lesions that went undiagnosed and then progressed into more invasive restorations was estimated to be between $57M-$218M more (difference between NaF varnish and class II restorations), and $150M-$443M more (difference between Class II restoration and crown or crown with RCT). CONCLUSIONS: BWRs are crucial in diagnosing a significant number of carious lesions. There is considerable impact on health and cost to the national health system due to undiagnosed lesions. Practitioners need to be educated on reading and understanding BWR, and policy should be changed to cover BWR.

Diagnosis of Tooth Prognosis Using Artificial Intelligence.

The accurate diagnosis of individual tooth prognosis has to be determined comprehensively in consideration of the broader treatment plan. The objective of this study was to establish an effective artificial intelligence (AI)-based module for an accurate tooth prognosis decision based on the Harvard School of Dental Medicine (HSDM) comprehensive treatment planning curriculum (CTPC). The tooth prognosis of 2359 teeth from 94 cases was evaluated with 1 to 5 levels (1-Hopeless, 5-Good condition for long term) by two groups (Model-A with 16, and Model-B with 13 examiners) based on 17 clinical determining factors selected from the HSDM-CTPC. Three AI machine-learning methods including gradient boosting classifier, decision tree classifier, and random forest classifier were used to create an algorithm. These three methods were evaluated against the gold standard data determined by consensus of three experienced prosthodontists, and their accuracy was analyzed. The decision tree classifier indicated the highest accuracy at 0.8413 (Model-A) and 0.7523 (Model-B). Accuracy with the gradient boosting classifier and the random forest classifier was 0.6896, 0.6687, and 0.8413, 0.7523, respectively. Overall, the decision tree classifier had the best accuracy among the three methods. The study contributes to the implementation of AI in the decision-making process of tooth prognosis in consideration of the treatment plan.

Accuracy of a Method to Monitor Root Position Using a 3D Digital Crown/Root Model during Orthodontic Treatments.

This study aimed to assess the accuracy of a method of predicting post-movement root position during orthodontic treatment using a 3D digital crown/root model (3DCRM) created with pre-movement records of both cone-beam computed tomography (CBCT) and dental arch digital scans. Pre- and post-movement CBCT scans and dental arch digital scans of five patients who had completed orthodontic treatments were used in this study. The 3DCRM was superimposed onto the post-movement scanned dental arch to identify the post-movement root position (test method). Post-movement CBCT (referenced as the current method) served as the control to identify the actual post-movement root position. 3D-coordinate analysis revealed no significant differences between the test and current methods along the X and Y axes. However, the discrepancy on the Z axis (especially in cases of intrusion) was greater than that in all other directions for all three tooth types examined (p < 0.05). A strong positive correlation between the degree of discrepancy and the distance of tooth movement was observed on the Z axis (r = 0.71). The 3DCRM method showed promising potential to accurately predict root position during orthodontic treatments without the need for a second CBCT. However, root resorption, which affected the Z axis prediction, needs to be closely monitored using periapical radiographs to complement this method.

Retroperitoneoscopic treatment of ureteral invagination caused by a long fibroepithelial polyp protruding into the bladder: report of a case.

We describe how we performed retroperitoneoscopic surgery for a 15.5-cm fibroepithelial polyp, which originated in the lowest portion of the right upper ureter, protruded intermittently into the bladder, and caused ureteral invagination. To our knowledge, this is the first report of the retroperitoneoscopic management of ureteral invagination caused by a long fibroepithelial polyp.