RESUMO
Benefits emerging from applying high-entropy ceramics in Li-ion technology are already well-documented in a growing number of papers. However, an intriguing question may be formulated: how can the multicomponent solid solution-type material ensure stable electrochemical performance? Utilizing an example of nonequimolar Sn-based Sn0.8(Co0.2Mg0.2Mn0.2Ni0.2Zn0.2)2.2O4 high-entropy spinel oxide, we provide a comprehensive model explaining the observed very good cyclability. The material exhibits a high specific capacity above 600 mAh g-1 under a specific current of 50 mA g-1 and excellent capacity retention near 100% after 500 cycles under 200 mA g-1. The stability originates from the conversion-alloying reversible reactivity of the amorphous matrix, which forms during the first lithiation from the initial high-entropy structure, and preserves the high level of cation disorder at the atomic scale. In the altered Li-storage mechanism in relation to the simple oxides, the unwanted aggregated metallic grains are not exsolved from the anode and therefore do not form highly lithiated phases characterized by large volumetric changes. Also, the electrochemical activity of Mg from the oxide matrix can be clearly observed. Because the studied compound was prepared by a conventional solid-state route, implementation of the presented approach is facile and appears usable for any oxide anode material containing a high-entropy mixture of elements.
RESUMO
Given the extensive efforts focused on protecting the environment, eco-friendly cathode materials are a prerequisite for the development of Na-ion battery technology. Such materials should contain abundant and inexpensive elements. In the paper, we present NASICON-Na3Fe2-yMny(PO4)3 (y = 0, 0.1, 0.2, 0.3, and 0.4) cathode materials, which meet these requirements. Na3Fe2-yMny(PO4)3 compounds were prepared via a solid-state reaction at 600 °C, which allowed to obtain powders with submicron particles. The presence of manganese in the iron sub-lattice inhibits phase transitions, which occurs at â¼95 and â¼145 °C in Na3Fe2(PO4)3, changing the monoclinic structure to rhombohedral and affecting the structural and transport properties. The chemical stability of Na3Fe2-yMny(PO4)3 was thus higher than that of Na3Fe2(PO4)3, and it also exhibited enhanced structural, transport, and electrochemical properties. The observed correlation between the chemical composition and electrochemical properties proved the ability to precisely tune the crystal structure of NASICONs, allowing cathode materials with more desirable properties to be designed.
RESUMO
LiFePO4 is considered to be one of the most promising cathode materials for lithium ion batteries for electric vehicle (EV) application. However, there are still a number of unsolved issues regarding the influence of Li and Fe-site substitution on the physicochemical properties of LiFePO4. This is a review-type article, presenting results of our group, related to the possibility of the chemical modification of phosphoolivine by introduction of cation dopants in Li and Fe sublattices. Along with a synthetic review of previous papers, a large number of new results are included. The possibility of substitution of Li⺠by Al3+, Zr4+, W6+ and its influence on the physicochemical properties of LiFePO4 was investigated by means of XRD, SEM/EDS, electrical conductivity and Seebeck coefficient measurements. The range of solid solution formation in Li1-3xAlxFePO4, Li1-4xZrxFePO4 and Li1-6xWxFePO4 materials was found to be very narrow. Transport properties of the synthesized materials were found to be rather weakly dependent on the chemical composition. The battery performance of selected olivines was tested by cyclic voltammetry (CV). In the case of LiFe1-yMyPO4 (M = Mn, Co and Ni), solid solution formation was observed over a large range of y (0 < y ≤ 1). An increase of electrical conductivity for the substitution level y = 0.25 was observed. Electrons of 3d metals other than iron do not contribute to the electrical properties of LiFe1-yMyPO4, and substitution level y > 0.25 leads to considerably lower values of σ. The activated character of electrical conductivity with a rather weak temperature dependence of the Seebeck coefficient suggests a small polaron-type conduction mechanism. The electrochemical properties of LiFe1-yMyPO4 strongly depend on the Fe substitution level.