Corneal riboflavin gradients and UV-absorption characteristics after topical application of riboflavin in concentrations ranging from 0.1 to 0.5.

Avoiding damage of the endothelial cells, especially in thin corneas, remains a challenge in corneal collagen crosslinking (CXL). Knowledge of the riboflavin gradients and the UV absorption characteristics after topical application of riboflavin in concentrations ranging from 0.1% to 0.5% could optimize the treatment. In this study, we present a model to calculate the UV-intensity depending on the corneal thickness. Ten groups of de-epithelialized porcine corneas were divided into 2 subgroups. Five groups received an imbibition of 10 min and the other five groups for 30 min. The applied riboflavin concentrations were 0.1%, 0.2%, 0.3%, 0.4% and 0.5% diluted in a 15% dextran solution for each subgroup. After the imbibition process, two-photon fluorescence microscopy was used to determine fluorescence intensity, which was compared to samples after saturation, yielding the absolute riboflavin concentration gradient of the cornea. The extinction coefficient of riboflavin solutions was measured using a spectrophotometer. Combining the obtained riboflavin concentrations and the extinction coefficients, a depth-dependent UV-intensity profile was calculated for each group. With increasing corneal depth, the riboflavin concentration decreased for all imbibition solutions and application times. The diffusion coefficients of 10 min imbibition time were higher than for 30 min. A higher RF concentration and a longer imbibition time resulted in higher UV-absorption and a lower UV-intensity in the depth of the cornea. Calculated UV-transmission was 6 percentage points lower compared to the measured transmission. By increasing the riboflavin concentration of the imbibition solution, a substantially higher UV-absorption inside the cornea is achieved. This offers a simple treatment option to control the depth of crosslinking e.g. in thin corneas, resulting in a lower risk of endothelial damage.

Chemistry matters: A side-by-side comparison of two chemically distinct methacryloylated dECM bioresins for vat photopolymerization.

Decellularized extracellular matrix (dECM) is an excellent natural source for 3D bioprinting materials due to its inherent cell compatibility. In vat photopolymerization, the use of dECM-based bioresins is just emerging, and extensive research is needed to fully exploit their potential. In this study, two distinct methacryloyl-functionalized, photocrosslinkable dECM-based bioresins were prepared from digested porcine liver dECM through functionalization with glycidyl methacrylate (GMA) or conventional methacrylic anhydride (MA) under mild conditions for systematic comparison. Although the chemical modifications did not significantly affect the structural integrity of the dECM proteins, mammalian cells encapsulated in the respective hydrogels performed differently in long-term culture. In either case, photocrosslinking during 3D (bio)printing resulted in transparent, highly swollen, and soft hydrogels with good shape fidelity, excellent biomimetic properties and tunable mechanical properties (~ 0.2-2.5 kPa). Interestingly, at a similar degree of functionalization (DOF ~ 81.5-83.5 %), the dECM-GMA resin showed faster photocrosslinking kinetics in photorheology resulting in lower final stiffness and faster enzymatic biodegradation compared to the dECM-MA gels, yet comparable network homogeneity as assessed via Brillouin imaging. While human hepatic HepaRG cells exhibited comparable cell viability directly after 3D bioprinting within both materials, cell proliferation and spreading were clearly enhanced in the softer dECM-GMA hydrogels at a comparable degree of crosslinking. These differences were attributed to the additional hydrophilicity introduced to dECM via methacryloylation through GMA compared to MA. Due to its excellent printability and cytocompatibility, the functional porcine liver dECM-GMA biomaterial enables the advanced biofabrication of soft 3D tissue analogs using vat photopolymerization-based bioprinting.