Tuning Structural Defects on a Nominal Single-Layered Graphene Oxide Membrane for Selective Separation of Biomolecules.

Two-dimensional (2D) materials provide a great opportunity for fabricating ideal membranes with ultrathin thickness for high-throughput separation. Graphene oxide (GO), owing to its hydrophilicity and functionality, has been extensively studied for membrane applications. However, fabrication of single-layered GO-based membranes utilizing structural defects for molecular permeation is still a great challenge. Optimization of the deposition methodology of GO flakes could offer a potential solution for fabricating desired nominal single-layered (NSL) membranes that can offer a dominant and controllable flow through structural defects of GO. In this study, a sequential coating methodology was adopted for depositing a NSL GO membrane, which is expected to have no or minimum stacking of GO flakes and thus ensure GO's structural defects as the major transport pathway. We have demonstrated effective rejection of different model proteins (bovine serum albumin (BSA), lysozyme, and immunoglobulin G (IgG)) by tuning the structural defect size via oxygen plasma etching. By generating appropriate structural defects, similar-sized proteins (myoglobin and lysozyme; molecular weight ratio (MWR): ∼1.14) were effectively separated with a separation factor of ∼6 and purity of 92%. These findings may provide new opportunities of using GO flakes for fabricating NSL membranes with tunable pores for applications in the biotechnology industry.

The Influence of Thermal Treatments on Anchor Effect in NMT Products.

The anchor effect in nanomolding technology (NMT) refers to the effect that polymer nanorods in nanopores on metal surfaces act as anchors to firmly bond the outside polymer components onto the metal surface. In this work, the influences of thermal treatments on the anchor effect are studied at microscopic level from the perspective of interfacial interaction by a model system (poly(n-butyl methacrylate) (PBMA) and alumina nanopore composite). The differential scanning calorimeter and fluorescence results indicate that the formation of a dense polymer layer in close contact with the pore walls after proper thermal treatments is the key for a strong interfacial interaction. Such polymer layers were formed in NMT products composed of PBMA and aluminum after slow cooling or annealing, with an up to eighteen-fold improvement of the interfacial bonding strength. The polymer chains near the nanopore walls eliminate the thermal stress induced by the mismatch of thermal expansion coefficients through relaxation over time and remain in close proximity with the pore walls during the cooling process of nanomolding. The above dynamic behaviors of the polymer chains ensure the formation of stable interfacial interaction, and then lead to the formation of the anchor effect.

The design of Mn2+&Co2+ co-doped CdTe quantum dot sensitized solar cells with much higher efficiency.

High quality Mn2+-doped CdTe quantum dots (QDs), Co2+-doped CdTe QDs and Mn2+&Co2+ co-doped CdTe QDs were successfully synthesized via an aqueous phase method with mercaptopropanoic acid (MPA) ligands. The doped QDs maintain the same zinc blende structure of CdTe by X-ray diffraction (XRD). The Mn2+-doped CdTe QDs and Co2+-doped CdTe QDs both show a red-shift on absorption and photoluminescence (PL) spectra compared to pure CdTe QDs. In addition, Mn2+-doped CdTe QDs show a significant increase in the PL lifetime due to an orbitally forbidden d-d transition, which is of benefit to the reduction of electron recombination loss. Co2+ doping has a more matched doping energy level. In view of this, Mn2+&Co2+ co-doped CdTe QDs were applied as sensitizers for quantum dot sensitized solar cells, resulting in a significantly enhanced efficiency.

Silver ion-doped CdTe quantum dots as fluorescent probe for Hg2+ detection.

Mercury(ii), which is a well-known toxic species, exists in the industrial waste water in many cases. In the present work, CdTe quantum dots (QDs) are studied as a fluorescence probe for Hg2+ detection. Ag ions are induced to QDs to enlarge their detection concentration range. l-cysteine is employed in the QD-based fluorescence probe to connect QDs with Hg2+. X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy results indicate the formation of zinc blende CdTe QDs with sizes of ∼5 nm and the existence of Ag+ in crystalline CdTe. Photoluminescence (PL) spectra and PL decay spectra were acquired to investigate the emission mechanism of Ag-doped CdTe QDs, revealing multi-emission in QD samples with higher concentrations of Ag+ doping. The highest PL quantum yield of the QD samples was 59.4%. Furthermore, the relationship between the fluorescence intensity and the concentration of Hg2+ has been established. Two linear relationships were obtained for the plot of F/F0 against Hg2+ concentration, enlarging the detection concentration range of Hg2+.

Na+-gated water-conducting nanochannels for boosting CO2 conversion to liquid fuels.

Robust, gas-impeding water-conduction nanochannels that can sieve water from small gas molecules such as hydrogen (H2), particularly at high temperature and pressure, are desirable for boosting many important reactions severely restricted by water (the major by-product) both thermodynamically and kinetically. Identifying and constructing such nanochannels into large-area separation membranes without introducing extra defects is challenging. We found that sodium ion (Na+)-gated water-conduction nanochannels could be created by assembling NaA zeolite crystals into a continuous, defect-free separation membrane through a rationally designed method. Highly efficient in situ water removal through water-conduction nanochannels led to a substantial increase in carbon dioxide (CO2) conversion and methanol yield in CO2 hydrogenation for methanol production.