Heterogeneous-Structured Molybdenum Diboride as a Novel and Promising Anode for Lithium-Ion Batteries.

With the development of electric vehicles, exploiting anode materials with high capacity and fast charging capability is an urgent requirement for lithium-ion batteries (LIBs). Borophene, with the merits of high capacity, high electronic conductivity and fast diffusion kinetics, holds great potential as anode for LIBs. However, it is difficult to fabricate for the intrinsic electron-deficiency of boron atom. Herein, heterogeneous-structured MoB2 (h-MoB2 ) with amorphous shell and crystalline core, is prepared by solid phase molten salt method. As demonstrated, crystalline core can encapsulate the honeycomb borophene within two adjacent Mo atoms, and amorphous shell can accommodate more lithium ions to strengthen the lithium storage capacity and diffusion kinetics. According to theoretical calculations, the lithium adsorption energy in MoB2 is about -2.7 eV, and the lithium diffusion energy barrier in MoB2 is calculated to be 0.199 eV, guaranteeing the enhanced adsorption capability and fast diffusion kinetic behavior of Li+ ions. As a result, h-MoB2 anode presents high capacity of 798 mAh g-1 at 0.1 A g-1 , excellent rate performance of 183 mAh g-1 at 5 A g-1 and long-term cyclic stability for 1200 cycles. This work may inspire ideas for the fabrication of borophene analogs and two-dimensional metal borides.

Application of ultrasonic-enhanced active seed crystals in the removal of sodium oxalate from alumina refinery waste liquor.

When organic matter, especially sodium oxalate (Na2C2O4), accumulates to a certain extent, it will seriously affect the alumina production process in the refinery and therefore urgently needs to be removed. This work attempts to illuminate the benefits of ultrasonic intensification of the crystallization process of Na2C2O4, taking the alumina refinery waste liquor, i.e., flat plate washing liquor, as a case study. The effects of different operating parameters (seed crystal addition amount, caustic soda concentration, reaction time, ultrasonic power) on the crystallization behavior and yield are discussed, and it is found that ultrasonic can increase the Na2C2O4 removal rate to 70.4%. The addition of ultrasonic promotes the morphological evolution of Na2C2O4 and is of great significance to the optimization of the components of the precipitated Na2C2O4. Specifically, the proportion of Na2C2O4 in the crystallized product reaches 64% with conventional conditions, while it reaches 77% with ultrasonic conditions. Therefore, ultrasonic can greatly reduce the alkali loss caused by the crystallization process of Na2C2O4 in flat plate washing liquor, which has great economic benefits.

Microstructure Evolution and Mechanical Properties of 0.4C-Si-Mn-Cr Steel during High Temperature Deformation.

Herein, the effects of height-diameter ratios (H/D) on the microstructure evolution and mechanical properties of 0.4C-Si-Mn-Cr steel during high temperature deformation are reported. The compression experiments were performed on steel samples using Gleeble to obtain a reasonable deformation temperature, and the degree of deformation was assessed in the range of 1.5 to 2.0 H/D via forging. The forged specimens were quenched using the same heat treatment process. The hardness and impact toughness of the steel samples were tested before and after heat treatment. Grain sizes gradually increased with an increase in the compression temperature from 950 °C to 1150 °C, and the grain sizes decreased with an increase in H/D. The microstructure of the steel samples contained pearlite, bainite, martensite, and retained austenite phase. The microstructure after forging was more uniform and finer as compared to that of as-cast steel samples. The hardness and impact toughness of the steel samples were evaluated after forging; hardness first increased and then decreased with an increase in H/D, while the impact toughness continuously increased with an increase in H/D. Hence, the microstructure and properties of steel could be improved via high temperature deformation, and this was primarily related to grain refinement.

The Particle Shape of WC Governing the Fracture Mechanism of Particle Reinforced Iron Matrix Composites.

In this work, tungsten carbide particles (WCp, spherical and irregular particles)-reinforced iron matrix composites were manufactured utilizing a liquid sintering technique. The mechanical properties and the fracture mechanism of WCp/iron matrix composites were investigated theoretically and experimentally. The crack schematic diagram and fracture simulation diagram of WCp/iron matrix composites were summarized, indicating that the micro-crack was initiated both from the interface for spherical and irregular WCp/iron matrix composites. However, irregular WCp had a tendency to form spherical WCp. The micro-cracks then expanded to a wide macro-crack at the interface, leading to a final failure of the composites. In comparison with the spherical WCp, the irregular WCp were prone to break due to the stress concentration resulting in being prone to generating brittle cracking. The study on the fracture mechanisms of WCp/iron matrix composites might provide a theoretical guidance for the design and engineering application of particle reinforced composites.