Sponge Spray-Reaching New Dimensions of Direct Sampling and Analysis by MS.

Sample preparation for the analysis of clinical samples with the mass spectrometer (MS) can be extensive and expensive. Simplifying and speeding up the process would be very beneficial. This paper reports sponge spray-a novel sampling and direct MS analysis approach-attempting exactly that. It enables direct analysis without any sample preparation from dried blood, plasma, and urine. The tip of a volumetric absorptive microsampling device is used to collect an exact amount of sample and from that same tip an electrospray can be directed into a mass spectrometer. We demonstrate here that, although with significant matrix effects, quantitation of penicillin G, a common antimicrobial, is possible in plasma and in urine, with essentially no sample preparation.

Synthesis and enhanced room-temperature thermoelectric properties of CuO-MWCNT hybrid nanostructured composites.

This work presents the synthesis of novel copper oxide-multiwalled carbon nanotube (CuO-MWCNT) hybrid nanostructured composites and a systematic study of their thermoelectric performance at near-room temperatures as a function of MWCNT wt% in the composite. The CuO-MWCNT hybrid nanostructured composites were synthesized by thermal oxidation of a thin metallic Cu layer pre-deposited on the MWCNT network. This resulted in the complete incorporation of MWCNTs in the nanostructured CuO matrix. The thermoelectric properties of the fabricated CuO-MWCNT composites were compared with the properties of CuO-MWCNT networks prepared by mechanical mixing and with the properties of previously reported thermoelectric [CuO]99.9[SWCNT]0.1 composites. CuO-MWCNT hybrid composites containing MWCNTs below 5 wt% showed an increase in the room-temperature thermoelectric power factor (PF) by ∼2 times compared with a bare CuO nanostructured reference thin film, by 5-50 times compared to mixed CuO-MWCNT networks, and by ∼10 times the PF of [CuO]99.9[SWCNT]0.1. The improvement of the PF was attributed to the changes in charge carrier concentration and mobility due to the processes occurring at the large-area CuO-MWCNT interfaces. The Seebeck coefficient and PF reached by the CuO-MWCNT hybrid nanostructured composites were 688 µV K-1 and ∼4 µW m-1 K-2, which exceeded the recently reported values for similar composites based on MWCNTs and the best near-room temperature inorganic thermoelectric materials such as bismuth and antimony chalcogenides and highlighted the potential of CuO-MWCNT hybrid nanostructured composites for applications related to low-grade waste heat harvesting and conversion to useable electricity.

Fiber-Reinforced Plywood: Increased Performance with Less Raw Material.

Fiber-reinforced plywood is a composite material that combines the natural strength and rigidity of plywood with the added durability and resilience provided by reinforcing fibers. This type of plywood is designed to offer improved characteristics over standard plywood, including enhanced strength, stiffness, resistance to impact and moisture, and environmental degradation. By integrating reinforcing fibers, such as glass, carbon, or natural fibers (like flax, bamboo, or hemp) into or onto plywood, manufacturers can create a material that is better suited for applications where traditional plywood might fall short or when a decrease in product weight or savings in wood raw material are necessary. This report reviews the current progress in fiber-reinforced plywood in the context of plywood as a construction material to better understand the potential gains in plywood applications, mechanical parameters, and material savings. It is found that a simple and cost-effective procedure of fiber reinforcement allows for substantial improvements in plywood's mechanical properties, typically to the extent of 10-40%. It is suggested that the wider adoption of fiber-reinforced plywood, especially in load- and impact-bearing applications, would greatly contribute to enhanced durability and longevity of the material while also allowing for more sustainable use of raw wood material.

Laser-based analytical techniques in cultural heritage science - Tutorial review.

This tutorial review combines the fundamentals of the design and operation of lasers with their usage in applications related to conservation and cultural heritage (CH) science - as components of analytical devices for the study of the chemical composition of materials. The development of laser instruments and their fundamental physical background, including a short explanation of their properties and parameters, are briefly summarised, and an overview of different laser-based analytical techniques is given. The analytical techniques covered in this tutorial are divided into three groups based on their technical aspects and properties: (1) vibrational spectroscopy, (2) elemental analysis, and (3) different molecular mass spectrometric techniques.

The Effect of Prestressing and Temperature on Tensile Strength of Basalt Fiber-Reinforced Plywood.

The reinforcement of plywood is demonstrated by laminating pretensioned basalt fibers between veneer sheets, to fabricate so-called prestressed plywood. Belt type basalt fibers bearing a specific adhesion promoting silane sizing were aligned between veneer sheets with 20 mm spacing and were pretensioned at 150 N. Three-layer plywood samples were prepared and tested for tensile strength at room temperature and at 150 °C. The room temperature tensile tests revealed a 35% increase in tensile strength for prestressed plywood compared to that of the conventional specimen. The reinforcement effect deteriorated at 150 °C but was restored upon cooling to room temperature. The deterioration is attributed to the weakening of bonding between the basalt fibers and phenolic resin matrix at elevated temperatures due to the softening of the resin.

Simultaneous measurement of static and kinetic friction of ZnO nanowires in situ with a scanning electron microscope.

A novel method for in situ measurement of the static and kinetic friction is developed and demonstrated for zinc oxide nanowires (NWs) on oxidised silicon wafers. The experiments are performed inside a scanning electron microscope (SEM) equipped with a nanomanipulator with an atomic force microscope tip as a probe. NWs are pushed by the tip from one end until complete displacement is achieved, while NW bending is monitored by the SEM. The elastic bending profile of a NW during the manipulation process is used to calculate the static and kinetic friction forces.