RESUMO
Surface-enhanced Raman spectroscopy (SERS) technology is an attractive method for the prompt and accurate on-site screening of illicit drugs. As portable Raman systems are available for on-site screening, the readiness of SERS technology for sensing applications is predominantly dependent on the accuracy, stability and cost-effectiveness of the SERS strip. An atmospheric-pressure plasma-assisted chemical deposition process that can deposit an even distribution of nanogold particles in a one-step process has been developed. The process was used to print a nanogold film on a paper-based substrate using a HAuCl4 solution precursor. X-ray photoelectron spectroscopy (XPS) analysis demonstrates that the gold has been fully reduced and that subsequent plasma post-treatment decreases the carbon content of the film. Results for cocaine detection using this substrate were compared with two commercial SERS substrates, one based on nanogold on paper and the currently available best commercial SERS substrate based on an Ag pillar structure. A larger number of bands associated with cocaine was detected using the plasma-printed substrate than the commercial substrates across a range of cocaine concentrations from 1 to 5000 ng/mL. A detection limit as low as 1 ng/mL cocaine with high spatial uniformity was demonstrated with the plasma-printed substrate. It is shown that the plasma-printed substrate can be produced at a much lower cost than the price of the commercial substrate.
RESUMO
This study aimed to clarify the effect of wire structure and alkaline elements in wire composition on metal transfer behavior in metal-cored arc welding (MCAW). A comparison of metal transfer in pure argon gas was carried out using a solid wire (wire 1), a metal-cored wire without an alkaline element (wire 2), and another metal-cored wire with 0.084 mass% of sodium (wire 3). The experiments were conducted under 280 and 320 A welding currents, observed by high-speed imaging techniques equipped with laser assistance and bandpass filters. At 280 A, wire 1 showed a streaming transfer mode, while the others showed a projected one. When the current was 320 A, the metal transfer of wire 2 changed to streaming, while wire 3 remained projected. As sodium has a lower ionization energy than iron, the mixing of sodium vapor into the iron plasma increases its electrical conductivity, raising the proportion of current flowing through metal vapor plasma. As a result, the current flows to the upper region of the molten metal on the wire tip, with the resulting electromagnetic force causing droplet detachment. Consequently, the metal transfer mode in wire 3 remained projected. Furthermore, weld bead formation is the best for wire 3.
RESUMO
This study aims to reduce the diffusible hydrogen content in deposited metal during gas metal arc welding (GMAW) and flux-cored arc welding (FCAW) which induces cold cracking. To achieve this, a novel welding torch with a dual gas nozzle has been developed. This special welding torch decreases the hydrogen source gas evaporated from a welding wire by the suction from the inner gas nozzle. In order to improve the suction efficiency of this evaporated gas, precise control of the suction gas flow is indispensable. In this paper, a simplified numerical simulation model of this process has been described. This model can take account of the evaporation of the hydrogen source gas from the wire while simulating the behavior of the shielding gas and the arc. Using this model, the effect of suction nozzle structure and torch operating conditions on suction gas flow pattern and suction efficiency was also investigated to understand the process mechanism. Furthermore, the diffusible hydrogen content in deposited metal was measured by chromatography as a validation step. Results show that some of the shielding gas introduced from a shielding nozzle was drawn inward and also branched into an upward flow that was sucked into the suction nozzle and a downward flow to a base metal. This branching height was defined as the suction limit height, which decisively governed the suction efficiency. As a result, in order to reduce the diffusible hydrogen, it was suggested that the suction limit height should be controlled towards below the wire position, where the evaporation rate of the hydrogen source gas peaks through optimization of the suction nozzle design and the torch operating conditions.
RESUMO
The generation of heat by clusters and arrays of gold nanoparticles under illumination is investigated theoretically. The nanoparticles are embedded in a homogeneous dielectric medium, and the finite thermal resistance at the interface between the nanoparticle and the medium is taken into account. An analytic solution is derived for the case of a single nanoparticle. The T-matrix method is used to calculate the energy absorption efficiency of groups of nanoparticles, taking into account their optical interactions. Heat transfer equations are developed that take into account thermal interactions between nanoparticles. The equations are solved numerically using the finite element software COMSOL. Periodic boundary conditions are applied to treat the thermal interactions between the nanoparticles for arrays of nanoparticles. Results are presented for illumination by a standard xenon flash lamp. The thermal resistance at the nanoparticle-medium interface is found to strongly influence the nanoparticle temperature, but to have negligible influence on the temperature of the dielectric medium after a few tens of nanoseconds of exposure to the flash lamp pulse. Optical interactions are found to be important if particle centres are separated by about twice the particle diameter or less. Thermal interactions between nanoparticles via the medium are found to be the dominant factor in determining the temperature increase in the dielectric medium. The maximum temperature increase is proportional to the volume fraction of the nanoparticles in the medium.
Assuntos
Ouro/química , Temperatura Alta , Iluminação , Nanopartículas Metálicas/química , Modelos TeóricosRESUMO
: The characteristics of the welding heat source for tandem narrow-gap gas metal arc welding are examined for different ternary shielding gas (Ar-CO2-He) compositions. Results of previous calculations of arc properties for bead-on-plate geometry are adapted to the narrow-gap geometry to predict these characteristics. The heat source concentration factor decreases and the maximum heat flux density increases as the helium content increases, which leads to an increased welding heat efficiency. Addition of CO2 up to around 10% also increases the heat efficiency. When the CO2 content exceeds 10%, the heat source concentration factor increases significantly and the heat efficiency decreases. The shielding gas composition also affects the heat source distribution. The heat source characteristics are applied to a computational fluid dynamic model of the weld pool to predict the weld shape, and the predictions are verified by experiment. The results indicate that the appropriate addition of helium to the shielding gas can increase the heat transferred to the peripheral regions of the arc and increase the sidewall penetration.
RESUMO
Cold atmospheric-pressure plasma (CAP) is a relatively new method used for bacterial inactivation. CAP is ionized gas that can be generated by applying an electric current to air or a feeding gas. It contains reactive species and emits UV radiation, which have antibacterial activity. Previous data suggests that CAP is effective in microbial inactivation and can decontaminate and sterilize surfaces, but its exact mode of action is still under debate. This study demonstrates the effect of CAP on the whole proteome of Pseudomonas aeruginosa PAO1 biofilms, which is a dominant pathogen in cystic fibrosis and medical device-related infections. Liquid chromatography-mass spectrometry (LC-MS) was used to identify differentially regulated proteins of whole cell P. aeruginosa extracts. A total of 16 proteins were identified to be affected by plasma treatment compared to the control. Eight of the identified proteins have functions in transcription and translation and their expression changes are likely to be part of a general physiological response instead of a CAP-specific adaptation. However, CAP also affected bacterioferritin (Bfr), Isocitrate dehydrogenase (Idh), Trigger factor (Tig) and a chemotaxis protein, which may be involved in P. aeruginosa's specific response to CAP. We confirm that bacterioferritin B plays a role in the bacterial response to CAP because ΔbfrB mutants of both PAO1 and PA14 are more susceptible to plasma-induced cell-death than their corresponding wild-type strains. To our knowledge, this is the first study showing the effect of plasma on the whole proteome of a pathogenic microorganism. It will help our understanding of the mode of action of CAP-mediated bacterial inactivation and thus support a safe and effective routine use of CAP in clinical and industrial settings.
Assuntos
Antibacterianos/farmacologia , Proteínas de Bactérias/efeitos dos fármacos , Grupo dos Citocromos b/efeitos dos fármacos , Ferritinas/efeitos dos fármacos , Plasma/metabolismo , Proteoma/efeitos dos fármacos , Pseudomonas aeruginosa/efeitos dos fármacos , Pressão Atmosférica , Biofilmes/efeitos dos fármacos , Morte Celular/efeitos dos fármacos , Fibrose Cística/tratamento farmacológico , Fibrose Cística/microbiologia , Viabilidade Microbiana/efeitos dos fármacos , Biossíntese de Proteínas/efeitos dos fármacos , Transcrição Gênica/efeitos dos fármacosRESUMO
Adverse environmental conditions at planting, such as cold temperature or water limitation, can lead to a reduced level of seed germination and plant establishment for cotton. Cold atmospheric-pressure plasma (CAP) treatment of cotton seeds prior to planting may help alleviate this problem. CAP is ionised gas that has a range of biological activities due to the formation of a mix of reactive oxygen and nitrogen species (RONS), excited molecules, charged particles and UV photons. Our results show that a 27 minutes CAP treatment using air can significantly increase water absorption of the seed, and improve warm germination, metabolic chill test germination and chilling tolerance in cotton. We also observe that the beneficial effect of CAP treatment is long-lasting and stable as improved germination activity is still seen when treatment occurs 4 months before germination testing, suggesting that future large-scale industrial seed plasma treatments may still be effectively applied well (months) before the seed planting. We conclude that CAP treatment is a promising new tool for use in the cotton industry that has the potential to significantly improve plant establishment in a wider range of environmental conditions.
Assuntos
Germinação , Gossypium/crescimento & desenvolvimento , Gases em Plasma/metabolismo , Sementes/crescimento & desenvolvimento , Agricultura/métodos , Temperatura Baixa , Gossypium/metabolismo , Sementes/metabolismo , Água/metabolismoRESUMO
Cold atmospheric plasma has recently emerged as a simple, low-cost and efficient physical method for inducing significant biological responses in seeds and plants without the use of traditional, potentially environmentally-hazardous chemicals, fungicides or hormones. While the beneficial effects of plasma treatment on seed germination, disease resistance and agricultural output have been reported, the mechanisms that underpin the observed biological responses are yet to be fully described. This study employs Fourier Transform Infrared (FTIR) spectroscopy and emission spectroscopy to capture chemical interactions between plasmas and seed surfaces with the aim to provide a more comprehensive account of plasma-seed interactions. FTIR spectroscopy of the seed surface confirms plasma-induced chemical etching of the surface. The etching facilitates permeation of water into the seed, which is confirmed by water uptake measurements. FTIR of exhaust and emission spectra of discharges show oxygen-containing species known for their ability to stimulate biochemical processes and deactivate pathogenic microorganisms. In addition, water gas, CO2, CO and molecules containing -C(CH3)3- moieties observed in FTIR spectra of the exhaust gas during plasma treatment may be partly responsible for the plasma chemical etching of seed surface through oxidizing the organic components of the seed coat.
Assuntos
Impedância Elétrica , Germinação , Gossypium/crescimento & desenvolvimento , Gases em Plasma/farmacologia , Sementes/crescimento & desenvolvimento , Gossypium/efeitos dos fármacos , Oxigênio/metabolismo , Sementes/efeitos dos fármacos , Espectroscopia de Infravermelho com Transformada de Fourier , Água/químicaRESUMO
Thermal chemical vapour deposition techniques for graphene fabrication, while promising, are thus far limited by resource-consuming and energy-intensive principles. In particular, purified gases and extensive vacuum processing are necessary for creating a highly controlled environment, isolated from ambient air, to enable the growth of graphene films. Here we exploit the ambient-air environment to enable the growth of graphene films, without the need for compressed gases. A renewable natural precursor, soybean oil, is transformed into continuous graphene films, composed of single-to-few layers, in a single step. The enabling parameters for controlled synthesis and tailored properties of the graphene film are discussed, and a mechanism for the ambient-air growth is proposed. Furthermore, the functionality of the graphene is demonstrated through direct utilization as an electrode to realize an effective electrochemical genosensor. Our method is applicable to other types of renewable precursors and may open a new avenue for low-cost synthesis of graphene films.
Assuntos
Técnicas Biossensoriais/instrumentação , Grafite/síntese química , Química Verde/métodos , Nanotecnologia/métodos , Ar , Técnicas Biossensoriais/métodos , Técnicas Eletroquímicas/métodos , Eletrodos , Gases/química , Teste de Materiais , Nanoestruturas/química , Óleo de Soja/química , Propriedades de SuperfícieRESUMO
Cold atmospheric-pressure plasma (CAP) is a relatively new method being investigated for antimicrobial activity. However, the exact mode of action is still being explored. Here we report that CAP efficacy is directly correlated to bacterial cell wall thickness in several species. Biofilms of Gram positive Bacillus subtilis, possessing a 55.4 nm cell wall, showed the highest resistance to CAP, with less than one log10 reduction after 10 min treatment. In contrast, biofilms of Gram negative Pseudomonas aeruginosa, possessing only a 2.4 nm cell wall, were almost completely eradicated using the same treatment conditions. Planktonic cultures of Gram negative Pseudomonas libanensis also had a higher log10 reduction than Gram positive Staphylococcus epidermidis. Mixed species biofilms of P. aeruginosa and S. epidermidis showed a similar trend of Gram positive bacteria being more resistant to CAP treatment. However, when grown in co-culture, Gram negative P. aeruginosa was more resistant to CAP overall than as a mono-species biofilm. Emission spectra indicated OH and O, capable of structural cell wall bond breakage, were present in the plasma. This study indicates that cell wall thickness correlates with CAP inactivation times of bacteria, but cell membranes and biofilm matrix are also likely to play a role.
Assuntos
Antibacterianos/farmacologia , Bactérias Gram-Negativas/efeitos dos fármacos , Bactérias Gram-Positivas/efeitos dos fármacos , Gases em Plasma/farmacologia , Antibacterianos/química , Argônio/química , Biofilmes/efeitos dos fármacos , Parede Celular , Testes de Sensibilidade Microbiana , Gases em Plasma/química , Análise EspectralRESUMO
Pseudomonas aeruginosa ATCC 9027 (DSM1128) is often used as a quality-control strain for sterility and microbial contamination testing and is an important biosurfactant producer. Here, we present the 6.4-Mb draft genome sequence and highlight some genomic differences to its closest relative, P. aeruginosa strain PA7.
RESUMO
Pseudomonas aeruginosa is an important opportunistic pathogen displaying high antibiotic resistance. Its resistance is in part due to its outstanding ability to form biofilms on a range of biotic and abiotic surfaces leading to difficult-to-treat, often long-term infections. Cold atmospheric plasma (CAP) is a new, promising antibacterial treatment to combat antibiotic-resistant bacteria. Plasma is ionized gas that has antibacterial properties through the generation of a mix of reactive oxygen and nitrogen species (RONS), excited molecules, charged particles and UV photons. Our results show the efficient removal of P. aeruginosa biofilms using a plasma jet (kINPen med), with no viable cells detected after 5 min treatment and no attached biofilm cells visible with confocal microscopy after 10 min plasma treatment. Because of its multi-factorial action, it is widely presumed that the development of bacterial resistance to plasma is unlikely. However, our results indicate that a short plasma treatment (3 min) may lead to the emergence of a small number of surviving cells exhibiting enhanced resistance to subsequent plasma exposure. Interestingly, these cells also exhibited a higher degree of resistance to hydrogen peroxide. Whole genome comparison between surviving cells and control cells revealed 10 distinct polymorphic regions, including four belonging to the redox active, antibiotic pigment phenazine. Subsequently, the interaction between phenazine production and CAP resistance was demonstrated in biofilms of transposon mutants disrupted in different phenazine pathway genes which exhibited significantly altered sensitivity to CAP.
Assuntos
Biofilmes/efeitos dos fármacos , Fenazinas/farmacologia , Gases em Plasma/farmacologia , Pseudomonas aeruginosa/fisiologia , Genoma Bacteriano/efeitos dos fármacos , Peróxido de Hidrogênio/farmacologia , Viabilidade Microbiana/efeitos dos fármacos , OxirreduçãoRESUMO
Microwave energy at 2.45 GHz was applied to a mixture of exhaust gases from a petrol engine at atmospheric pressure. It was found that by pulsing the microwave energy with a 50% duty cycle, the average power required to sustain a microwave-induced plasma discharge was decreased by about 40%. The ratio of absorbed to incident power was unaffected. These findings were confirmed for pulse frequencies from 10 to 300 Hz.
Assuntos
Poluentes Atmosféricos/química , Poluição do Ar/prevenção & controle , Gases/química , Gasolina , Temperatura Alta , Micro-Ondas , Emissões de Veículos/prevenção & controle , Transferência de EnergiaRESUMO
The combined diffusion coefficient method is widely used to treat the mixing and demixing of different plasma gases and vapours in thermal plasmas, such as welding arcs and plasma jets. It greatly simplifies the treatment of diffusion for many gas mixtures without sacrificing accuracy. Here, three subjects that are important in the implementation of the combined diffusion coefficient method are considered. First, it is shown that different expressions for the combined diffusion coefficients, arising from different definitions for the stoichiometric coefficients that assign the electrons to the two gases, are equivalent. Second, an approach is presented for calculating certain partial differential terms in the combined temperature and pressure diffusion coefficients that can cause difficulties. Finally, a method for applying the combined diffusion coefficients in computational models, which typically require diffusion to be expressed in terms of mass fraction gradients, is given.
RESUMO
Cold atmospheric pressure plasma (APP) is a recent, cutting-edge antimicrobial treatment. It has the potential to be used as an alternative to traditional treatments such as antibiotics and as a promoter of wound healing, making it a promising tool in a range of biomedical applications with particular importance for combating infections. A number of studies show very promising results for APP-mediated killing of bacteria, including removal of biofilms of pathogenic bacteria such as Pseudomonas aeruginosa. However, the mode of action of APP and the resulting bacterial response are not fully understood. Use of a variety of different plasma-generating devices, different types of plasma gases and different treatment modes makes it challenging to show reproducibility and transferability of results. This review considers some important studies in which APP was used as an antibacterial agent, and specifically those that elucidate its mode of action, with the aim of identifying common bacterial responses to APP exposure. The review has a particular emphasis on mechanisms of interactions of bacterial biofilms with APP.
Assuntos
Antibacterianos/farmacologia , Pressão Atmosférica , Bactérias/efeitos dos fármacos , Controle de Infecções/métodos , Gases em Plasma/farmacologia , HumanosRESUMO
Atmospheric gas plasmas (AGPs) are able to selectively induce apoptosis in cancer cells, offering a promising alternative to conventional therapies that have unwanted side effects such as drug resistance and toxicity. However, the mechanism of AGP-induced cancer cell death is unknown. In this study, AGP is shown to up-regulate intracellular reactive oxygen species (ROS) levels and induce apoptosis in melanoma but not normal melanocyte cells. By screening genes involved in apoptosis, we identify tumor necrosis factor (TNF)-family members as the most differentially expressed cellular genes upon AGP treatment of melanoma cells. TNF receptor 1 (TNFR1) antagonist-neutralizing antibody specifically inhibits AGP-induced apoptosis signal, regulating apoptosis signal-regulating kinase 1 (ASK1) activity and subsequent ASK1-dependent apoptosis. Treatment of cells with intracellular ROS scavenger N-acetyl-l-cysteine also inhibits AGP-induced activation of ASK1, as well as apoptosis. Moreover, depletion of intracellular ASK1 reduces the level of AGP-induced oxidative stress and apoptosis. The evidence for TNF-signaling dependence of ASK1-mediated apoptosis suggests possible mechanisms for AGP activation and regulation of apoptosis-signaling pathways in tumor cells.
Assuntos
Apoptose , MAP Quinase Quinase Quinase 5/metabolismo , Gases em Plasma/farmacologia , Espécies Reativas de Oxigênio/metabolismo , Fator de Necrose Tumoral alfa/metabolismo , Atmosfera , Caspase 3/metabolismo , Caspase 7/metabolismo , Linhagem Celular Tumoral , Sobrevivência Celular , Humanos , Melanoma , Estresse Oxidativo , Transdução de SinaisRESUMO
A method is developed for determining the optical properties of an optically rough coating on an opaque substrate from reflectance measurements. A modified Kubelka-Munk two- flux model is used to calculate the reflectance of the coating as a function of the refractive index, absorption coefficient, scattering coefficient, and thickness. The calculated reflectance is then fitted to measurements using a spectral projected gradient algorithm, allowing the optical properties to be obtained. The technique is applied to titanium dioxide coatings on a titanium substrate. Realistic values of refractive index and absorption coefficients are generally obtained. Quantities that are useful for solar water-splitting applications are calculated, including the depth profile of absorption and the proportion of the incident photon flux absorbed in the coating under solar illumination.