RESUMO
Photoresponsive molecular memory films were fabricated by a layer-by-layer (LbL) assembling of two dinuclear Ru complexes with tetrapodal phosphonate anchors, containing either 2,3,5,6-tetra(2-pyridyl)pyrazine or 1,2,4,5-tetra(2-pyridyl)benzene as a bridging ligand (Ru-NP and Ru-CP, respectively), using zirconium phosphonate to link the layers. Various types of multilayer homo- and heterostructures were constructed. In the multilayer heterofilms such as ITO||(Ru-NP)m |(Ru-CP)n , the difference in redox potentials between Ru-NP and Ru-CP layers was approximately 0.7 V, which induced a potential gradient determined by the sequence of the layers. In the ITO||(Ru-NP)m |(Ru-CP)n multilayer heterofilms, the direct electron transfer (ET) from the outer Ru-CP layers to the ITO were observed to be blocked for m>2, and charge trapping in the outer Ru-CP layers became evident from the appearance of an intervalence charge transfer (IVCT) band at 1140 nm from the formation of the mixed-valent state of Ru-CP units, resulting from the reductive ET mediation of the inner Ru-NP layers. Therefore, the charging/discharging ("1"and "0") states in the outer Ru-CP layers could be addressed and interconverted by applying potential pulses between -0.5 and +0.7 V. The two states could be read out by the direction of the photocurrent (anodic or cathodic). The molecular heterolayer films thus represent a typical example of a photoresponsive memory device; that is, the writing process may be achieved by the applied potential (-0.5 or +0.7 V), while the readout process is achieved by measuring the direction of the photocurrent (anodic or cathodic). Sequence-sensitive multilayer heterofilms, using redox-active complexes as building blocks, thus demonstrate great potential for the design of molecular functional devices.
RESUMO
The ancillary ligands 4'-(4-pyridyl)-2,2':6',2''-terpyridine and 4'-(2,3-dihydrobenzo[b]thiophene)-2,2'-6',2"-terpyridine were used to synthesize two series of mono- and dinuclear ruthenium complexes differing in their lengths and anchoring groups. The electrochemical and single-molecular conductance properties of these two series of ruthenium complexes were studied experimentally by means of cyclic voltammetry and the scanning tunneling microscopy-break junction technique (STM-BJ) and theoretically by means of density functional theory (DFT). Cyclic voltammetry data showed clear redox peaks corresponding to both the metal- and ligand-related redox reactions. Single-molecular conductance demonstrated an exponential decay of the molecular conductance with the increase in molecular length for both the series of ruthenium complexes, with decay constants of ßPY =2.07±0.1â nm(-1) and ßBT =2.16±0.1â nm(-1) , respectively. The contact resistance of complexes with 2,3-dihydrobenzo[b]thiophene (BT) anchoring groups is found to be smaller than the contact resistance of ruthenium complexes with pyridine (PY) anchors. DFT calculations support the experimental results and provided additional information on the electronic structure and charge transport properties in those metal|ruthenium complex|metal junctions.
RESUMO
Molecular multilayers were fabricated using a Ru complex containing Fe cations on an indium tin oxide surface to control the properties of the Ru-complex multilayers such as the multilayer orientation and the electron transport. The Ru-complex multilayer films containing Fe cations were thicker than those containing Zr cations, which have been used previously. The electron transport properties of the multilayers containing Fe cations were evaluated. Solid-state sandwich cell measurements showed that the Ru-complex multilayer films containing Fe cations exhibited increased electron transport with a lower transport coefficient ß of 0.01 Å(-1), whereas those that contain Zr cations have ß â¼ 0.07 Å(-1). Thus, Fe cations are effective in obtaining thicker Ru-complex layers with increased electron transport abilities.