Noninvasive and Multiplex Self-Test of Kidney Disease Biomarkers with Graphene-Based Lab-on-a-Chip (G-LOC): Toward Digital Diagnostics in the Hands of Patients.

Chronic kidney disease is one of the major health issues worldwide. However, diagnosis is now highly centralized in large laboratories, resulting in low access to patient monitoring and poor personalized treatments. This work reports the development of a graphene-based lab-on-a-chip (G-LOC) for the digital testing of renal function biomarkers in serum and saliva samples. G-LOC integrates multiple bioelectronic sensors with a microfluidic system that enables multiplex self-testing of urea, potassium, sodium, and chloride. The linearity, limit of detection (LOD), accuracy, and coefficient of variability (CV) were studied. Accuracy values higher than 95.5% and CV lower than 9% were obtained for all of the biomarkers. The analytical performance was compared against three reference lab benchtop analyzers by measuring healthy- and renal-failure-level samples of serum. From receiver operating characteristic (ROC) plots, sensitivities (%) of 99.7, 97.6, 99.1, and 89.0 were obtained for urea, potassium, sodium, and chloride, respectively. Then, the test was evaluated in noninvasive saliva samples and compared against reference methods. Correlation and Bland-Altman plots showed good correlation and agreement of the G-LOC with the reference methods. It is noteworthy that the precision of G-LOC was similar to better than benchtop lab analyzers, with the advantage of being highly portable. Finally, a user testing study was conducted. The analytical performance obtained with untrained volunteers was similar to that obtained with trained chemists. Additionally, based on a user experience survey, G-LOC was found to have very simple usability and would be suitable for at-home diagnostics.

Field-effect transistors engineered via solution-based layer-by-layer nanoarchitectonics.

The layer-by-layer (LbL) technique has been proven to be one of the most versatile approaches in order to fabricate functional nanofilms. The use of simple and inexpensive procedures as well as the possibility to incorporate a very wide range of materials through different interactions have driven its application in a wide range of fields. On the other hand, field-effect transistors (FETs) are certainly among the most important elements in electronics. The ability to modulate the flowing current between a source and a drain electrode via the voltage applied to the gate electrode endow these devices to switch or amplify electronic signals, being vital in all of our everyday electronic devices. In this topical review, we highlight different research efforts to engineer field-effect transistors using the LbL assembly approach. We firstly discuss on the engineering of the channel material of transistors via the LbL technique. Next, the deposition of dielectric materials through this approach is reviewed, allowing the development of high-performance electronic components. Finally, the application of the LbL approach to fabricate FETs-based biosensing devices is also discussed, as well as the improvement of the transistor's interfacial sensitivity by the engineering of the semiconductor with polyelectrolyte multilayers.

The Effect of Amino-Phosphate Interactions on the Biosensing Performance of Enzymatic Graphene Field-Effect Transistors.

The interaction between polyamines and phosphate species is found in a wide range of biological and abiotic systems, yielding crucial consequences that range from the formation of supramolecular colloids to structure determination. In this work, the occurrence of phosphate-amino interactions is evidenced from changes in the electronic response of graphene field effect transistors (gFETs). First, the surface of the transistors is modified with poly(allylamine), and the effect of phosphate binding on the transfer characteristics is interpreted in terms of its impact on the surface charge density. The electronic response of the polyamine-functionalized gFETs is shown to be sensitive to the presence of different phosphate anions, such as orthophosphate, adenosine triphosphate, and tripolyphosphate, and a simple binding model is developed to explain the dependence of the shift of the Dirac point potential on the phosphate species concentration. Afterward, the impact of phosphate-amino interactions on the immobilization of enzymes to polyamine-modified graphene surfaces is investigated, and a decrease in the amount of anchored enzyme as the phosphate concentration increases is found. Finally, multilayer polyamine-urease biosensors are fabricated while increasing the phosphate concentration in the enzyme solution, and the sensing properties of the gFETs toward urea are evaluated. It is found that the presence of simple phosphate anions alters the nanoarchitecture of the polyelectrolyte-urease assemblies, with direct implications on urea sensing.

Reversible Switching of the Dirac Point in Graphene Field-Effect Transistors Functionalized with Responsive Polymer Brushes.

The reversible control of the graphene Dirac point using external chemical stimuli is of major interest in the development of advanced electronic devices such as sensors and smart logic gates. Here, we report the coupling of chemoresponsive polymer brushes to reduced graphene oxide (rGO)-based field-effect transistors to modulate the graphene Dirac point in the presence of specific divalent cations. Poly[2-(methacryloyloxy)ethyl] phosphate (PMEP) brushes were grown on the transistor channel by atom transfer radical polymerization initiated from amine-pyrene linkers noncovalently attached to rGO surfaces. Our results show an increase in the Dirac point voltage due to electrostatic gating effects upon the specific binding of Ca2+ and Mg2+ to the PMEP brushes. We demonstrate that the electrostatic gating is reversibly controlled by the charge density of the polymer brushes, which depends on the divalent cation concentration. Moreover, a theoretical formalism based on the Grahame equation and a Langmuir-type binding isotherm is presented to obtain the PMEP-cation association constant from the experimental data.

The effect of ionic strength and phosphate ions on the construction of redox polyelectrolyte-enzyme self-assemblies.

Layer by layer assembly of polyelectrolytes with proteins is a convenient tool for the development of functional biomaterials. Most of the studies presented in the literature are based on the electrostatic interaction between components of opposite charges, limiting the assembly possibilities. However, this process can be tuned by modifying the environment where the main constituents are dissolved. In this work, the electron transfer behavior between an electroactive polyelectrolyte (polyallylamine derivatized with an osmium complex) and a redox enzyme (glucose oxidase) is studied by assembling them in the presence of phosphate ions at different ionic strengths. Our results show that the environment from which the assembly is constructed has a significant effect on the electrochemical response. Notably, the polyelectrolyte dissolved in the presence of phosphate at high ionic strength presents a globular structure which is preserved after adsorption with substantial effects on the buildup of the multilayer system, improving the electron transfer process through the film.

Surfactants as mesogenic agents in layer-by-layer assembled polyelectrolyte/surfactant multilayers: nanoarchitectured "soft" thin films displaying a tailored mesostructure.

Interfacial supramolecular architectures displaying mesoscale organized components are of fundamental importance for developing materials with novel or optimized properties. Nevertheless, engineering the multilayer assembly of different building blocks onto a surface and exerting control over the internal mesostructure of the resulting film is still a challenging task in materials science. In the present work we demonstrate that the integration of surfactants (as mesogenic agents) into layer-by-layer (LbL) assembled polyelectrolyte multilayers offers a straightforward approach to control the internal film organization at the mesoscale level. The mesostructure of films constituted of hexadecyltrimethylammonium bromide, CTAB, and polyacrylic acid, PAA (of different molecular weights), was characterized as a function of the number of assembled layers. Structural characterization of the multilayered films by grazing-incidence small-angle X-ray scattering (GISAXS), showed the formation of mesostructured composite polyelectrolyte assemblies. Interestingly, the (PAA/CTA)n assemblies prepared with low PAA molecular weight presented different mesostructural regimes which were dependent on the number of assembled layers: a lamellar mesophase for the first bilayers, and a hexagonal circular mesophase for n ≥ 7. This interesting observation was explained in terms of the strong interaction between the substrate and the first layers leading to a particular mesophase. As the film increases its thickness, the prevalence of this strong interaction decreases and the supramolecular architecture exhibits a "bulk" mesophase. Finally, we demonstrated that the molecular weight of the polyelectrolyte has a considerable impact on the meso-organization for the (PAA/CTA)n assemblies. We consider that these studies open a path to new rational methodologies to construct "nanoarchitectured" polyelectrolyte multilayers.

Transduction of Amine-Phosphate Supramolecular Interactions and Biosensing of Acetylcholine through PEDOT-Polyamine Organic Electrochemical Transistors.

Organic electrochemical transistors (OECTs) are important devices for the development of flexible and wearable sensors due to their flexibility, low power consumption, sensitivity, selectivity, ease of fabrication, and compatibility with other flexible materials. These features enable the creation of comfortable, versatile, and efficient portable devices that can monitor and detect a wide range of parameters for various applications. Herein, we present OECTs based on PEDOT-polyamine thin films for the selective monitoring of phosphate-containing compounds. Our findings reveal that supramolecular single phosphate-amino interaction induces higher changes in the OECT response compared to ATP-amino interactions, even at submillimolar concentrations. The steric character of binding anions plays a crucial role in OECT sensing, resulting in a smaller shift in maximum transconductance voltage and threshold voltage for bulkier binding species. The OECT response reflects not only the polymer/solution interface but also events within the conducting polymer film, where ion transport and concentration are affected by the ion size. Additionally, the investigation of enzyme immobilization reveals the influence of phosphate species on the assembly behavior of acetylcholinesterase (AchE) on PEDOT-PAH OECTs, with increasing phosphate concentrations leading to reduced enzyme anchoring. These findings contribute to the understanding of the mechanisms of OECT sensing and highlight the importance of careful design and optimization of the biosensor interface construction for diverse sensing applications.

Biofunctionalization of Graphene-Based FET Sensors through Heterobifunctional Nanoscaffolds: Technology Validation toward Rapid COVID-19 Diagnostics and Monitoring.

The biofunctionalization of graphene field-effect transistors (GFETs) through vinylsulfonated-polyethyleneimine nanoscaffold is presented for enhanced biosensing of severe acute respiratory-related coronavirus 2 (SARS-CoV-2) spike protein and human ferritin, two targets of great importance for the rapid diagnostic and monitoring of individuals with COVID-19. The heterobifunctional nanoscaffold enables covalent immobilization of binding proteins and antifouling polymers while the whole architecture is attached to graphene by multivalent π-π interactions. First, to optimize the sensing platform, concanavalin A is employed for glycoprotein detection. Then, monoclonal antibodies specific against SARS-CoV-2 spike protein and human ferritin are anchored, yielding biosensors with limit of detections of 0.74 and 0.23 nm, and apparent affinity constants ( K D G F E T ) of 6.7 and 8.8 nm, respectively. Both biosensing platforms show good specificity, fast time response, and wide dynamic range (0.1-100 nm). Moreover, SARS-CoV-2 spike protein is also detected in spiked nasopharyngeal swab samples. To rigorously validate this biosensing technology, the GFET response is matched with surface plasmon resonance measurements, exhibiting linear correlations (from 2 to 100 ng cm-2) and good agreement in terms of K D values. Finally, the performance of the biosensors fabricated through the nanoscaffold strategy is compared with those obtained through the widely employed monopyrene approach, showing enhanced sensitivity.

Mass and charge transport in highly mesostructured polyelectrolyte/electroactive-surfactant multilayer films.

HYPOTHESIS: Dimensionally stable electroactive films displaying spatially addressed redox sites is still a challenging goal due to gel-like structure. Polyelectrolyte and surfactants can yield highly mesostructured films using simple buildup strategies as layer-by-layer. The use of redox modified surfactants is expected to introduce order and an electroactive response in thin films. EXPERIMENTS: The assembly of polyacrylic acid and different combinations of redox-modified and unmodified hexadecyltrimethylammonium bromide yields highly structured and electroactive thin films. The growth, viscoelastic properties, mass, and electron transport of these films were studied by combining electrochemical and quartz crystal balance with dissipation experiments. FINDINGS: Our results show that the films are highly rigid and poorly hydrated. The mass and charge transport reveal that the ingress (egress) of the counter ions during the electrochemical oxidation (reduction) is accompanied with a small amount of water, which is close to their hydration sphere. Thus, the generated mesostructured films present an efficient charge transport with negligible changes in their structures during the electron transfer process. The control over the meso-organization and its stability represents a promising tool in the construction of devices where the vectorial transfer of electrons, or ions, is required.

Mesoporous thin films on graphene FETs: nanofiltered, amplified and extended field-effect sensing.

The ionic screening and the response of non-specific molecules are great challenges of biosensors based on field-effect transistors (FETs). In this work, we report the construction of graphene based transistors modified with mesoporous silica thin films (MTF-GFETs) and the unique (bio)sensing properties that arise from their synergy. The developed method allows the preparation of mesoporous thin films free of fissures, with an easily tunable thickness, and prepared on graphene-surfaces, preserving their electronic properties. The MTF-GFETs show good sensing capacity to small probes that diffuse inside the mesopores and reach the graphene semiconductor channel such as H+, OH-, dopamine and H2O2. Interestingly, MTF-GFETs display a greater electrostatic gating response in terms of amplitude and sensing range compared to bare-GFETs for charged macromolecules that infiltrate the pores. For example, for polyelectrolytes and proteins of low MW, the amplitude increases almost 100% and the sensing range extends more than one order of magnitude. Moreover, these devices show a size-excluded electrostatic gating response given by the pore size. These features are even displayed at physiological ionic strength. Finally, a developed thermodynamic model evidences that the amplification and extended field-effect properties arise from the decrease of free ions inside the MTFs due to the entropy loss of confining ions in the mesopores. Our results demonstrate that the synergistic coupling of mesoporous films with FETs leads to nanofiltered, amplified and extended field-effect sensing (NAExFES).

Surface Engineering of Graphene through Heterobifunctional Supramolecular-Covalent Scaffolds for Rapid COVID-19 Biomarker Detection.

Graphene is a two-dimensional semiconducting material whose application for diagnostics has been a real game-changer in terms of sensitivity and response time, variables of paramount importance to stop the COVID-19 spreading. Nevertheless, strategies for the modification of docking recognition and antifouling elements to obtain covalent-like stability without the disruption of the graphene band structure are still needed. In this work, we conducted surface engineering of graphene through heterofunctional supramolecular-covalent scaffolds based on vinylsulfonated-polyamines (PA-VS). In these scaffolds, one side binds graphene through multivalent π-π interactions with pyrene groups, and the other side presents vinylsulfonated pending groups that can be used for covalent binding. The construction of PA-VS scaffolds was demonstrated by spectroscopic ellipsometry, Raman spectroscopy, and contact angle measurements. The covalent binding of -SH, -NH2, or -OH groups was confirmed, and it evidenced great chemical versatility. After field-effect studies, we found that the PA-VS-based scaffolds do not disrupt the semiconducting properties of graphene. Moreover, the scaffolds were covalently modified with poly(ethylene glycol) (PEG), which improved the resistance to nonspecific proteins by almost 7-fold compared to the widely used PEG-monopyrene approach. The attachment of recognition elements to PA-VS was optimized for concanavalin A (ConA), a model lectin with a high affinity to glycans. Lastly, the platform was implemented for the rapid, sensitive, and regenerable recognition of SARS-CoV-2 spike protein and human ferritin in lab-made samples. Those two are the target molecules of major importance for the rapid detection and monitoring of COVID-19-positive patients. For that purpose, monoclonal antibodies (mAbs) were bound to the scaffolds, resulting in a surface coverage of 436 ± 30 ng/cm2. KD affinity constants of 48.4 and 2.54 nM were obtained by surface plasmon resonance (SPR) spectroscopy for SARS-CoV-2 spike protein and human ferritin binding on these supramolecular scaffolds, respectively.

Mesostructured Electroactive Thin Films Through Layer-by-Layer Assembly of Redox Surfactants and Polyelectrolytes.

Electroactive thin films are an important element in the devices devoted to energy conversion, actuators, and molecular electronics, among others. Their build-up by the layer-by-layer technique is an attractive choice since a fine control over the thickness and composition can be achieved. However, most of the assemblies described in the literature show a lack of internal order, and their thicknesses change upon oxidation-state alterations. In this work, we describe the formation of layer-by-layer assemblies of redox surfactants and polyelectrolytes that leads to the construction of mesoscale organized electroactive films. In contrast to thin films prepared with traditional redox polymers, here, the redox surfactant does not only allow the control of the film meso-organization (from 2D hexagonal to circular hexagonal phases) but it also allows the control of the number and position of the redox centers. Finally, these films show high stability and a negligible structural deformation under redox-state changes.

PEDOT-polyamine composite films for bioelectrochemical platforms - flexible and easy to derivatize.

We report a straightforward route for the preparation of flexible, electrochemically stable and easily functionalizable poly(3,4-ethylenedioxythiophene) (PEDOT) composite films deposited on PET foils as biosensing platforms. For this purpose, poly(allylamine) hydrochloride (PAH) was blended with PEDOT to provide amine-bearing sites for further biofunctionalization as well as to improve the mechanical properties of the films. The conducting PEDOT-PAH composite films were characterized by cyclic voltammetry, UV-vis and Raman spectroscopies. An exhaustive stability study was carried out from the mechanical, morphological and electrochemical viewpoint. Subsequent sugar functionalization of the available amine groups from PAH allowed for the specific recognition of lectins and the subsequent self-assembly of glycoenzymes (glucose oxidase and horseradish peroxidase) concomitant with the prevention of non-specific protein fouling. The platforms presented good bioelectrochemical performance (glucose oxidation and hydrogen peroxide reduction) in the presence of redox mediators. The developed composite films constitute a promising option for the construction of all-polymer biosensing platforms with great potential owing to their flexibility, high transmittance, electrochemical stability and the possibility of glycosylation, which provides a simple route for specific biofunctionalization as well as an effective antifouling strategy.

Lectin-Recognizable MOF Glyconanoparticles: Supramolecular Glycosylation of ZIF-8 Nanocrystals by Sugar-Based Surfactants.

A strategy toward the integration of highly functional microporous materials, such as metal-organic frameworks (MOFs), in composites via biochemical recognition interactions is presented. Postsynthetic modification of zeolitic-imidazolate framework-8 MOF nanocrystals with a maltose-exposing biocompatible surfactant (the so-called "Glyco-MOFs") was performed to confer affinity toward lectin protein concanavalin A. The addition of small amounts of concanavalin A to the colloidal Glyco-MOF dispersion triggers the aggregation of these units into self-limited size supramolecular architectures directed by specific sugar-lectin binding interactions.

Enzyme Multilayers on Graphene-Based FETs for Biosensing Applications.

Electrochemical sensors represent a powerful tool for real-time measurement of a variety of analytes of much significance to different areas, ranging from clinical diagnostics to food technology. Point-of-care devices which can be used at patient bedside or for online monitoring of critical parameters are of great importance in clinical daily routine. In this work, portable, low-cost electrochemical sensors for a fast and reliable detection of the clinically relevant analyte urea have been developed. The intrinsic pH sensitivity of reduced graphene oxide (rGO)-based field-effect transistors (FETs) was exploited to monitor the enzymatic hydrolysis of urea. The functionalization of the sensor platform using the layer-by-layer technique is especially advantageous for the immobilization of the biorecognition element provided that this approach preserves the enzyme integrity as well as the rGO surface. The great selectivity of the enzyme (urease) combined with the high sensitivity of rGO-based FETs result in the construction of urea biosensors with a limit of detection (LOD) of 1µM and a linear range up to 1mM. Quantification of Cu2+ with a LOD down to 10nM was performed by taking advantage of the specific inhibition of urease in the presence of heavy metals. These versatile biosensors offer great possibilities for further development of highly sensitive enzyme-based FETs for real-time, label-free detection of a wide variety of clinically relevant analytes.

Cascading reaction of arginase and urease on a graphene-based FET for ultrasensitive, real-time detection of arginine.

Herein, a biosensor based on a reduced graphene oxide field effect transistor (rGO-FET) functionalized with the cascading enzymes arginase and urease was developed for the detection of L-arginine. Arginase and urease were immobilized on the rGO-FET sensing surface via electrostatic layer-by-layer assembly using polyethylenimine (PEI) as cationic building block. The signal transduction mechanism is based on the ability of the cascading enzymes to selectively perform chemical transformations and prompt local pH changes, that are sensitively detected by the rGO-FET. In the presence of L-arginine, the transistors modified with (PEI/urease(arginase)) multilayers showed a shift in the Dirac point due to the change in the local pH close to the graphene surface, produced by the catalyzed urea hydrolysis. The transistors were able to monitor L-arginine in the 10-1000 µM linear range with a LOD of 10 µM, displaying a fast response and a good long-term stability. The sensor showed stereospecificity and high selectivity in the presence of non-target amino acids. Taking into account the label-free, real-time measurement capabilities and the easily quantifiable, electronic output signal, this biosensor offers advantages over state-of-the-art L-arginine detection methods.

Enzyme-polyelectrolyte multilayer assemblies on reduced graphene oxide field-effect transistors for biosensing applications.

We present the construction of layer-by-layer (LbL) assemblies of polyethylenimine and urease onto reduced-graphene-oxide based field-effect transistors (rGO FETs) for the detection of urea. This versatile biosensor platform simultaneously exploits the pH dependency of liquid-gated graphene-based transistors and the change in the local pH produced by the catalyzed hydrolysis of urea. The use of an interdigitated microchannel resulted in transistors displaying low noise, high pH sensitivity (20.3µA/pH) and transconductance values up to 800 µS. The modification of rGO FETs with a weak polyelectrolyte improved the pH response because of its transducing properties by electrostatic gating effects. In the presence of urea, the urease-modified rGO FETs showed a shift in the Dirac point due to the change in the local pH close to the graphene surface. Markedly, these devices operated at very low voltages (less than 500mV) and were able to monitor urea in the range of 1-1000µm, with a limit of detection (LOD) down to 1µm, fast response and good long-term stability. The urea-response of the transistors was enhanced by increasing the number of bilayers due to the increment of the enzyme surface coverage onto the channel. Moreover, quantification of the heavy metal Cu2+(with a LOD down to 10nM) was performed in aqueous solution by taking advantage of the urease specific inhibition.

Recognition-driven assembly of self-limiting supramolecular protein nanoparticles displaying enzymatic activity.

We report the recognition-driven assembly of self-limiting protein nanoparticles displaying enzymatic activity. Solution self-assembly of concanavalin A lectin and glycoenzyme glucose oxidase leads to the spontaneous formation of biocolloids with well-defined dimensions, narrow size distribution and remarkable stability. These biocolloids successfully recognize a glycosylated modified electrode retaining the enzyme activity.