Study on the UV FEL single-shot damage threshold of an Au thin film.

The damage threshold of an Au-coated flat mirror, one of the reflective optics installed on the FEL-2 beamline of the Dalian Coherent Light Source, China, upon far-UV free-electron laser irradiation is evaluated. The surface of the coating is characterized by profilometer and optical microscope. A theoretical approach of the phenomenon is also presented, by application of conventional single-pulse damage threshold calculations, a one-dimensional thermal diffusion model, as well as finite-element analysis with ANSYS.

Structural and optical performance of NiV/Ti multilayer mirrors for Z-pinch plasma diagnostic at the wavelength region of 350-450†eV.

This Letter reports on investigations of novel, to the best of our knowledge, NiV(Ni93V7)/Ti multilayer mirrors for the operation in the wavelength region of 350-450 eV. Such mirrors are promising optical components for the Z-pinch plasma diagnostic. The NiV/Ti multilayers show superior structural and optical performance compared to conventional Ni/Ti multilayers. Replacing Ni with NiV in multilayers decreases interface widths and enhances the contrast of the refractive index between the absorber and spacer layers. The improvement of interface quality contributes to the enhancement in reflectance. Under the grazing incidence of 13°, a peak reflectivity of 25.1% at 429 eV is achieved for NiV/Ti multilayers, while 17.7% at 427 eV for Ni/Ti.

Selective corticofugal modulation on sound processing in auditory thalamus of awake marmosets.

Cortical feedback has long been considered crucial for the modulation of sensory perception and recognition. However, previous studies have shown varying modulatory effects of the primary auditory cortex (A1) on the auditory response of subcortical neurons, which complicate interpretations regarding the function of A1 in sound perception and recognition. This has been further complicated by studies conducted under different brain states. In the current study, we used cryo-inactivation in A1 to examine the role of corticothalamic feedback on medial geniculate body (MGB) neurons in awake marmosets. The primary effects of A1 inactivation were a frequency-specific decrease in the auditory response of most MGB neurons coupled with an increased spontaneous firing rate, which together resulted in a decrease in the signal-to-noise ratio. In addition, we report for the first time that A1 robustly modulated the long-lasting sustained response of MGB neurons, which changed the frequency tuning after A1 inactivation, e.g. some neurons are sharper with corticofugal feedback and some get broader. Taken together, our results demonstrate that corticothalamic modulation in awake marmosets serves to enhance sensory processing in a manner similar to center-surround models proposed in visual and somatosensory systems, a finding which supports common principles of corticothalamic processing across sensory systems.

Corticofugal modulation of temporal and rate representations in the inferior colliculus of the awake marmoset.

Temporal processing is crucial for auditory perception and cognition, especially for communication sounds. Previous studies have shown that the auditory cortex and the thalamus use temporal and rate representations to encode slowly and rapidly changing time-varying sounds. However, how the primate inferior colliculus (IC) encodes time-varying sounds at the millisecond scale remains unclear. In this study, we investigated the temporal processing by IC neurons in awake marmosets to Gaussian click trains with varying interclick intervals (2-100 ms). Strikingly, we found that 28% of IC neurons exhibited rate representation with nonsynchronized responses, which is in sharp contrast to the current view that the IC only uses a temporal representation to encode time-varying signals. Moreover, IC neurons with rate representation exhibited response properties distinct from those with temporal representation. We further demonstrated that reversible inactivation of the primary auditory cortex modulated 17% of the stimulus-synchronized responses and 21% of the nonsynchronized responses of IC neurons, revealing that cortico-colliculus projections play a role, but not a crucial one, in temporal processing in the IC. This study has significantly advanced our understanding of temporal processing in the IC of awake animals and provides new insights into temporal processing from the midbrain to the cortex.

Comparison of thermal stability of Mo/Si multilayers with different crystallinities of Mo layers.

To investigate the thermal stability of Mo/Si multilayers with different initial crystallinities of Mo layers, two kinds of Mo/Si multilayers were deposited by DC magnetron sputtering and annealed at 300°C and 400°C. The period thickness compactions of multilayers with crystalized and quasi-amorphous Mo layers were 0.15 nm and 0.30 nm at 300°C, respectively, and the stronger the crystallinity, the lower the extreme ultraviolet reflectivity loss. At 400°C, the period thickness compactions of multilayers with crystalized and quasi-amorphous Mo layers were 1.25 nm and 1.04 nm, respectively. It was shown that multilayers with a crystalized Mo layer had better thermal stability at 300°C but were less stable at 400°C than multilayers with a quasi-amorphous Mo layer. These changes in stability at 300°C and 400°C were due to the significant transition of the crystalline structure. The transition of the crystal structure leads to increased surface roughness, more interdiffusion, and compound formation.

Cr/C lamellar multilayer grating in conical diffraction mounting for beam splitter used in X-ray free-electron lasers.

A lamellar multilayer grating in a conical diffraction mounting was proposed as a beam splitter for X-ray free-electron lasers. Theoretical calculations demonstrated that the distribution of diffraction efficiency can be adjusted by optimizing the groove depth or d-spacing. A Cr/C multilayer lamellar grating with a line density of approximately 2500 L/mm was fabricated. The performance of the element was measured in the Optics Beamline PM-1 (BESSY-II) at an energy of 1500 eV. A five-order diffraction pattern was recognized, and the diffraction efficiencies of the -/+first-order were approximately 12.6 and 4.4%, respectively. The asymmetric distribution of diffraction efficiency can be caused by the different sidewall angles of the grating groove.

Cr/C multilayer growth on a heavy metal layer for upgrading of high efficiency tender x-ray gratings.

To increase efficiency of single layer gratings used in the tender x-ray range, a high reflectance multilayer can be directly grown on single layer gratings. Multilayer growth quality was studied by depositing the Cr/C multilayer on a Pt single layer using flat substrates. Their structure quality and adhesion were characterized by atomic force microscopy (AFM), grazing incidence x-ray reflectivity (GIXRR), x-ray scattering (XRS), x-ray diffraction (XRD), and layer adhesion measurement. AFM results showed that the surface roughness was 0.218 nm for the multilayer without the Pt layer and 0.272 nm for the multilayer with the Pt layer. As GIXRR results showed, the average interface widths were 0.39 nm for the multilayer without the Pt layer and 0.42 nm for the multilayer with the Pt layer. XRS results indicated that the existence of a Pt layer enlarged slightly the roughness of the multilayer. Simulation results exhibited that these slight changes caused by the Pt layer had an insignificant effect on reflectivity. As XRD results displayed, the crystallization of the Pt layer had negligible effects on the crystallization of Cr in films. The layer adhesion measurement revealed that the critical loads to peel off the layer from the substrate were 84.64 mN for the multilayer without the Pt layer and 33.99 mN for the multilayer with the Pt layer. After 6 months, the latter layer structure is undamaged, demonstrating that the coating is not easily peeled off. This study proves the feasibility to upgrade a low efficiency single Pt layer grating to a highly efficient multilayer grating.

Mo/Si lamellar multilayer gratings with high efficiency and enhanced resolution for the x-ray region of 1000-1700eV.

The d-spacing of the multilayer lamellar grating was theoretically optimized to improve the energy resolution and maintain a high efficiency. Based on the study of the growth behavior of Mo/Si multilayer on the lamellar grating under different sputtering pressures, Ar gas pressure of 1 mTorr was selected, which can fabricate the multilayer with lower roughness and a good replication of the groove shape. An absolute diffraction efficiency of 25.6% and a Cff factor of 1.79 were achieved for the -1st order of the Mo/Si lamellar multilayer grating at an energy of 1700 eV.

Simulation and measurement of systematic errors of stitching interferometry for high precision X-ray mirrors with large radius of curvature.

To accurately measure the surface figure of curved mirrors with large radius of curvature (RoC) using stitching interferometry methods, three types of measurement errors are systematically studied, including retrace error, defocusing error within a single subaperture, and stitching angle error among different subapertures. It was found that part of the retrace error caused by the mismatch between the reference wavefront and reflected wavefront has little effect, while the overall retrace error, including the influence of the imperfect optical elements, will cause an error of 1-2 nm RMS within a single subaperture. Defocusing error will enlarge the error due to amplification of optical path error caused by the deviation of the position of the CCD. Because the error is mainly in the edge area, a slope threshold, which controls the maximum surface slope of each subaperture, can be optimized to reduce the effect of the defocus on stitching measurement error. Constant angle error among neighboring subapertures has the biggest accumulation effect on the final stitched figure. For the spherical mirror with RoC of 100 m of 80mm×40mm, the error of the one-dimensional residual profile is 4.67 nm PV, assuming a constant angle error of 2×10-7rad. For the elliptical mirror with RoC of 60-140 m, it is more than 15 nm peak-to-valley (PV). It is because the profile difference caused by constant angle error is closer to a circle, which can be mostly removed after subtraction of a best-fit sphere. Based on the above error analysis, the developed algorithm-based stitching method was used to measure an elliptical cylindrical mirror of 74mm×40mm with RoC of 60-140 m, and the result was compared with a slope measurement instrument from the Beijing Synchrotron Radiation Facility. After removing the best fitting ellipse profile, the one-dimensional difference between the two results is only 0.77 nm RMS, which demonstrated good measurement accuracy.

Thermal and temporal stability of the nitridated Ru/B4C multilayer for high-flux monochromator application.

A nitridated Ru/B4C multilayer with period of 3.0 nm and 80 bilayers were fabricated to study thermal and temporal stability. The multilayer was annealed from room temperature to 490°C, and the in situ X-ray measurements showed that the reflectivity remains mostly unchanged up to 300°C. An essential drop of the reflectivity occurred at 490°C with significantly increased interface roughness. A new layered structure with larger thickness than the original multilayer started to appear at 400°C. The nitridated Ru/B4C multilayer remains intact after two years of storage in air, which demonstrated a very good temporal stability.

Stability of Cr/C multilayer during synchrotron radiation exposure and thermal annealing.

The stability of Cr/C multilayer during irradiation or thermal annealing was investigated using grazing incidence X-ray reflectivity measurement, X-ray photoelectron spectroscopy, X-ray diffraction analysis, small-angle X-ray scattering analysis, and soft X-ray reflectivity measurement. One sample was irradiated with a white beam of synchrotron radiation and five other samples were annealed at various temperatures. The 18-h irradiation treatment caused local surface contaminants but did not affect the buried stacks. The annealing treatment resulted in increased reflectivity at approximately 1.2 keV, and the multilayer remained stable for temperature up to 700 °C. Thus, the Cr/C multilayers exhibited excellent stability during irradiation and thermal treatments and can be used for the mirrors and multilayer gratings of third-generation synchrotron radiation systems.

Optimized highly efficient multilayer-coated blazed gratings for the tender X-ray region.

The optimized design of multilayer-coated blazed gratings (MLBG) for high-flux tender X-ray monochromators was systematically studied by numerical simulations. The resulting correlation between the multilayer d-spacing and grating blaze angle significantly deviated from the one predicted by conventional equations. Three high line density gratings with different blaze angles were fabricated and coated by the same Cr/C multilayer. The MLBG with an optimal blaze angle of 1.0° showed a record efficiency reaching 60% at 3.1 keV and 4.1 keV. The measured efficiencies of all three gratings were consistent with calculated results proving the validity of the numerical simulation and indicating a more rigorous way to design the optimal MLBG structure.

Stress and Microstructure Study of W/Si X-ray Multilayers with Different Structural Parameters.

X-ray Timing and Polarimetry (XTP) telescope is proposed by using nested focusing optics with a large effective area for studies in the field of high energy physics (energy region of 1-30 keV). Highreflectance and low-stress W/Si multilayers are required for this telescope to improve the spectral response and maintain the figure quality of the mirrors simultaneously. In this paper, we focused on the study of stress and layer structure of W/Si periodic multilayers at different d-spacings (thickness of period), thickness ratios, and bilayer numbers. The results show that the stress of the multilayer increased from -73.3 to -465.5 MPa with increase in the d-spacing from 2.7 to 5.5 nm, while the change in the average interface width was negligible, from 0.31 to 0.36 nm. For the multilayers prepared with different thickness ratios of W, from 0.3 to 0.67 (d = 3.7 nm), the lowest stress appeared at the ratio of ~0.46, and the average interface width was unchanged. The number of bilayers (N = 80-160) had negligible effects on both the layer structure and the stress, and the multilayers exhibited a very smooth surface morphology with a root-mean-square roughness of 0.19 nm. To further study the microstructural changes of the multilayer, X-ray diffraction measurements of the samples with different d-spacings and thickness ratios were performed. An increased crystallization along with phase changes were observed in the samples prepared with thicker W layers, which can increase the compressive stress of the multilayer.

Nitridated Ru/B4C multilayer mirrors with improved interface structure, zero stress, and enhanced hard X-ray reflectance.

Ru/B4C multilayer mirrors are used for hard X-ray monochromators with moderate spectral resolution and high integral flux. To overcome the problem of large compressive stress inherent in Ru/B4C multilayers, a reactive sputtering technique using a mixture working gas of argon and nitrogen with different partial pressures was tested, and the fabricated multilayers had a period of 3 nm. The intrinsic stress was essentially reduced after nitridation and relaxed to zero value at approximately 15% partial pressure of nitrogen in the working gas. Interface roughness was slightly increased which can be caused by the polycrystalline structure inside the nitridated samples. More importantly, the nitridated multilayers showed an enhanced reflectance (67% at 8.04 keV photon energy) as compared with the one fabricated with pure Ar (54%). The structure analysis with transmission electron microscopy and X-ray photoelectron spectroscopy demonstrated that nitrogen incorporated into a multilayer structure was mostly located in the B4C layers forming BN compounds, which suppressed the diffusion of boron, stabilized the interfaces and enhanced the reflectance.

Nitridated Pd/B4C multilayer mirrors for soft X-ray region: internal structure and aging effects.

Reactive sputtering with a mixture of argon and nitrogen (N2 partial pressure of 4%, 8%, and 15%) as the working gas is used to develop the high reflectance Pd/B4C multilayers for soft X-ray region application. Compared to the pure Ar fabricated sample, the interface roughness of the nitridated multilayer is slightly increased while the compressive stress is essentially relaxed from -623 MPa (pure Ar) to -85 MPa (15% N2). A maximum reflectance of 32% is measured at the wavelength of 9.5 nm for the multilayer fabricated with 15% N2. After storing the multilayers in an air environment for 6-17 months, a distinct aging effect is observed on the nitridated samples. The transmission electron microscopy results indicate that a large part of the top layers of the nitridated samples is deteriorated with severe interdiffusion, essential decrease in d-spacing, and compacted multilayer structure. The deterioration is less pronounced for the multilayers fabricated with a higher ratio of N2. Energy dispersive X-ray spectroscopy reveals that the concentration of nitrogen and boron in the degraded area is much reduced compared to the intact layers. A primitive model of upward diffusion of nitrogen and boron is proposed to explain the aging effects of the nitridated structure.

Structure and stress studies of low temperature annealed W/Si multilayers for the X-ray telescope.

Low stress W/Si multilayer mirrors are demanded in the hard X-ray telescopes to achieve the high angular resolution. To reduce the stress of the as-deposited multilayer and maintain a high reflectivity, two groups of low-temperature annealing experiments were performed on the periodic multilayers with a d-spacing of ~3.8 nm. The temperature-dependent experiments show that the 150 °C annealing can slightly increase the reflectivity while the stress reduced only by 24%. Higher temperature annealing induced a larger reduction of the stress and the multilayer reached an almost zero stress state at 250 °C. The stress relaxation was accompanied by a small drop of reflectivity of ≤5% and a period compaction of <0.02 nm. The time-dependent experiments indicate that most of the stress changes occurred within the first 10 minutes while a prolonged annealing is not useful. The X-ray scattering and transmission electron microscopy were further used to study the microstructure changes of the multilayers. It is found that the W/Si multilayer exhibits an amorphous structure before and after annealing, while an enhanced diffusion and intermixing is the main reason for the stress relaxation and structure changes.

Enhancement of the reflectivity of Al/Zr multilayers by a novel structure.

The reflectivity of Al/Zr multilayers is enhanced by the use of a novel structure. The Al layers are divided by insertion of Si layers. In addition, Si barrier layers are inserted at the Al/Zr interfaces (Zr-on-Al and Al-on-Zr). As a result, crystallization of the Al layer is inhibited and that of Zr is enhanced. In grazing incidence x-ray reflectometry, x-ray diffraction, and extreme ultraviolet measurements, the novel multilayers exhibit lower interfacial roughness compared with traditional multilayer structures, and their reflectivity is increased from 48.2% to 50.0% at a 5° angle of incidence. These novel multilayers also have potential applications in other multilayer systems and the semiconductor industry.

Comparative Study on Microstructure of Mo/Si Multilayers Deposited on Large Curved Mirror with and without the Shadow Mask.

The Mo/Si multilayer mirror has been widely used in EUV astronomy, lithography, microscopy and other fields because of its high reflectivity at the wavelength around 13.5 nm. During the fabrication of Mo/Si multilayers on large, curved mirrors, shadow mask was a common method to precisely control the period thickness distribution. To investigate the effect of shadow mask on the microstructure of Mo/Si multilayers, we deposited a set of Mo/Si multilayers with and without the shadow mask on a curved substrate with aperture of 200 mm by direct current (DC) magnetron sputtering in this work. Grazing incidence X-ray reflectivity (GIXR), diffuse scattering, atomic force microscope (AFM) and X-ray diffraction (XRD) were used to characterize the multilayer structure and the EUV reflectivity were measured at the National Synchrotron Radiation Laboratory (NSRL) in China. By comparing the results, we found that the layer microstructure including interface width, surface roughness, layer crystallization and the reflectivity were barely affected by the mask and a high accuracy of the layer thickness gradient can be achieved.

Hand-Rearing Method for Infant Marmosets.

The common marmoset (Callithrix jacchus) is a small and highly social New World monkey with high reproduction rates, which has been proven to be a compelling non-human primate model for biomedical and neuroscience research. Some females give birth to triplets; however, the parents cannot raise all of them. To save these infants, we have developed a hand-rearing method for raising newborn marmosets. In this protocol, we describe the formula of the food, the time for feeding, the configuration of the temperature and humidity, as well as the adaptation of the hand-reared infants to the colony environment. This hand-rearing method significantly increases the survival rate of marmoset infants (without hand-rearing: 45%; with hand-rearing: 86%) and provides the opportunity to study the development of marmoset infants with similar genetic backgrounds raised in different postnatal environments. As the method is practical and easy to use, we anticipate that it could also be applied to other labs working with common marmosets.

Effect of a High Estrogen Level in Early Pregnancy on the Development and Behavior of Marmoset Offspring.

The use of assisted reproductive technology (ART) has risen steadily worldwide over the past 3 decades and helps many infertile families. However, ART treatments lead to an abnormal internal environment in the uterus, which may increase the risks of health problems for the offspring. Higher maternal estradiol (E2) is a notable feature in women who use ART treatments, and this has been suggested as a key factor for the risk of diseases in the offspring. In the current study, we have established a marmoset model with a high E2 level in early pregnancy to examine its potential risk to the development and behavior of the offspring. In comparison with the normal group, babies of the high E2 group exhibited lower average survival rates and birth weights. However, those who survived in the high E2 group demonstrated normal vocal production with rich call repertoires, normal speed during locomotion, and normal behaviors in the home cage. In contrast to the normal group, surviving babies of the high E2 group spent more time sleeping during development without signs of sleep disorders. In summary, our study revealed that high estrogen in early pregnancy may cause low survival rates and birth weights of the offspring, though the surviving infants did not show obvious behavioral deficiencies during development. The current study is a valuable and highly important non-human primate study for evaluating the safety of ART treatments. However, it is worth noting that some results did not reach the significant level, which may be due to the small sample size caused by animal shortage stemming from the COVID-19 epidemic.