RESUMO
The utilization of municipal sludge as a seed sludge for initiating the autotrophic nitrogen removal (ANR) process presents a challenge due to the negligible abundance of anaerobic ammonia-oxidizing bacteria (AnAOB). Here, a computational fluid dynamics model was used to simulate sludge volume fraction and sludge particle velocity. A high-height-to-diameter-ratio airlift inner-circulation partition bioreactor (HHAIPBR) was operated for 175 d to enrich AnAOB from municipal sludge, and the performance of the ANR process was investigated. The start-up period of HHAIPBR inoculated with municipal sludge required approximately 69 d. A high nitrogen removal performance, with a mean total nitrogen removal efficiency of 82.1%, was obtained for 1 month. The simulation results validated the presence of sludge circulation and revealed the distribution characteristics of dissolved oxygen inside the reactor, further supporting the promotion of sludge granulation via the high height-to-diameter ratio. Nitrosomonas (3.31%) of Proteobacteria and Candidatus Brocadia (6.56%) of Planctomycetota were dominant in the HHAIPBR. This study presents a viable approach for the industrial cultivation of anammox sludge and the rapid start-up of the partial nitritation-anammox system.
Assuntos
Reatores Biológicos , Esgotos , Esgotos/microbiologia , Reatores Biológicos/microbiologia , Nitrogênio , OxirreduçãoRESUMO
OBJECTIVES: To investigate the incidence rate, clinical characteristics, and prognosis of neonatal stroke in Shenzhen, China. METHODS: Led by Shenzhen Children's Hospital, the Shenzhen Neonatal Data Collaboration Network organized 21 institutions to collect 36 cases of neonatal stroke from January 2020 to December 2022. The incidence, clinical characteristics, treatment, and prognosis of neonatal stroke in Shenzhen were analyzed. RESULTS: The incidence rate of neonatal stroke in 21 hospitals from 2020 to 2022 was 1/15 137, 1/6 060, and 1/7 704, respectively. Ischemic stroke accounted for 75% (27/36); boys accounted for 64% (23/36). Among the 36 neonates, 31 (86%) had disease onset within 3 days after birth, and 19 (53%) had convulsion as the initial presentation. Cerebral MRI showed that 22 neonates (61%) had left cerebral infarction and 13 (36%) had basal ganglia infarction. Magnetic resonance angiography was performed for 12 neonates, among whom 9 (75%) had involvement of the middle cerebral artery. Electroencephalography was performed for 29 neonates, with sharp waves in 21 neonates (72%) and seizures in 10 neonates (34%). Symptomatic/supportive treatment varied across different hospitals. Neonatal Behavioral Neurological Assessment was performed for 12 neonates (33%, 12/36), with a mean score of (32±4) points. The prognosis of 27 neonates was followed up to around 12 months of age, with 44% (12/27) of the neonates having a good prognosis. CONCLUSIONS: Ischemic stroke is the main type of neonatal stroke, often with convulsions as the initial presentation, involvement of the middle cerebral artery, sharp waves on electroencephalography, and a relatively low neurodevelopment score. Symptomatic/supportive treatment is the main treatment method, and some neonates tend to have a poor prognosis.
Assuntos
Acidente Vascular Cerebral , Humanos , Masculino , Recém-Nascido , Feminino , China/epidemiologia , Acidente Vascular Cerebral/epidemiologia , Prognóstico , Eletroencefalografia , Incidência , Imageamento por Ressonância MagnéticaRESUMO
Microplastics (MPs) have recently attracted much attention due to their widespread distribution in the aquatic environment. Microplastics can act as a vector of heavy metals in the aquatic environment, causing a potential threat to aquatic organisms and human health. This review mainly summarized the occurrence of microplastics in the aquatic environment and their interaction with heavy metals. Then, we considered the adsorption mechanisms of MPs and heavy metals, and further critically discussed the effects of microplastics properties and environmental factors (e.g., pH, DOM, and salinity) on the adsorption of heavy metals. Finally, the potential risks of combined exposure of MPs and heavy metals to aquatic biota were briefly evaluated. This work aims to provide a theoretical summary of the interaction between MPs and heavy metals, and is expected to serve as a reference for the accurate assessment of their potential risks in future studies.
Assuntos
Metais Pesados , Poluentes Químicos da Água , Adsorção , Humanos , Metais Pesados/toxicidade , Microplásticos , Plásticos , Poluentes Químicos da Água/análise , Poluentes Químicos da Água/toxicidadeRESUMO
OBJECTIVE: A modified method was used for cell entrapped beads (CEBs) preparation and two aeration intensities (low and high aeration intensity) was supplied as factors to investigate the change of quorum quenching performance for membrane biofouling in membrane bioreactor (MBR). RESULTS: Dehydrogenase activity and growth trend of activated sludge were improved at high aeration intensity. Compared with C-MBR (with vacant beads), QQ-MBR (with CEBs) had more stable quorum quenching activity and longer application time at high aeration intensity, in which the proteins and polysaccharides were reduced by 15 and 20%, respectively. The difference of EPS concentration in mixed liquor was attributed to the protein concentration controlled by quorum quenching bacteria, meanwhile sufficient organics was necessary to maintain the process. CONCLUSIONS: The better settleability, greater stability and relatively lower hydrophobicity of activated sludge properties was achieved with quorum quenching. The scouring effect of CEBs was promoted at high aeration intensity, further controlling the membrane biofouling.
Assuntos
Incrustação Biológica/prevenção & controle , Reatores Biológicos/microbiologia , Membranas/microbiologia , Percepção de Quorum , Esgotos/microbiologia , Polissacarídeos/análise , Proteínas/análiseRESUMO
A modified method was proposed which integrates the spatial patterns of toxic metals simulated by sequential indicator simulation, different exposure models and local current land uses extracted by remote-sensing software into a dose-response model for human health risk assessment of toxic metals. A total of 156 soil samples with a various land uses containing farm land (F1-F25), forest land (W1-W12) and residential land (U1-U15) were collected in a grid pattern throughout Xiandao District (XDD), Hunan Province, China. The total Cr and Pb in topsoil were analyzed. Compared with Hunan soil background values, the elevated concentrations of Cr were mainly located in the east of XDD, and the elevated concentrations of Pb were scattered in the areas around F1, F6, F8, F13, F14, U5, U14, W2 and W11. For non-carcinogenic effects, the hazard index (HI) of Cr and Pb overall the XDD did not exceed the accepted level to adults. While to children, Cr and Pb exhibited HI higher than the accepted level around some areas. The assessment results indicated Cr and Pb should be regarded as the priority pollutants of concern in XDD. The first priority areas of concern were identified in region A with a high probability (>0.95) of risk in excess of the accepted level for Cr and Pb. The areas with probability of risk between 0.85 and 0.95 in region A were identified to be the secondary priority areas for Cr and Pb. The modified method was proved useful due to its improvement on previous studies and calculating a more realistic human health risk, thus reducing the probability of excessive environmental management.
Assuntos
Exposição Ambiental/análise , Poluentes do Solo/análise , Solo/química , Adulto , Criança , China , Cromo/análise , Cromo/toxicidade , Relação Dose-Resposta a Droga , Humanos , Chumbo/análise , Chumbo/toxicidade , Modelos Teóricos , Medição de Risco , Poluentes do Solo/toxicidadeRESUMO
Micellar-enhanced ultrafiltration (MEUF) was applied to the separation of phenolic compounds p-nitrophenol (PNP), p-chlorophenol (PCP), p-cresol (PC) and phenol (P) from effluents using a hydrophilic polyethersulfone ultrafiltration membrane. Cationic cetylpyridinium chloride (CPC), nonionic TX-100 and anionic sodium dodecyl benzene sulfonate (SDBS) were chosen as the surfactants. Several important parameters, i.e. the separation efficiency, the distribution coefficient of phenolic compounds and the removal ratio of surfactants, were investigated. It was shown that the separation efficiency and the distribution coefficient of phenolic compounds ascended with the increasing surfactant concentration and could be arranged as the following order: PNP>PCP>PC>P. Moreover, in the case of phenolic compound separation, CPC achieved the highest treatment efficiency, and the separation efficiency of SDBS was a little lower than that of TX-100. The removal ratios of the same surfactant when treating different phenolic effluents were nearly similar. However, when treating the same phenolic compound, the sequence of the surfactant rejection was in the following order: TX-100>CPC>SDBS. These results indicate that CPC has a distinct superiority in the treatment of phenolic effluents via the MEUF process, and PNP easily solubilizes in the surface of the micelles.
Assuntos
Micelas , Fenóis/química , Tensoativos/química , Ultrafiltração/métodos , Eliminação de Resíduos Líquidos/métodos , Poluentes Químicos da Água/químicaRESUMO
Microplastics (MPs) accumulation in sediments has posed a huge threat to freshwater ecosystems. However, it is still unclear the effect of MPs on riparian sediment structures and contaminant adsorption under different hydrological processes. In this study, three concentrations of polyamide (PA) MPs-treated sediments (0.1%, 1%, and 10%, w/w) were subjected to natural (NA) exposure, dry-wet (DW) cycles, and freeze-thaw (FT) cycles. The results indicated that PA MPs-added sediment increased the micro-aggregates by 10.1%-18.6% after FT cycles, leading to a decrease in aggregate stability. The pH, OM, and DOC of sediments were significantly increased in DW and FT treatments. In addition, the increasing concentration of PA MPs showed an obvious decrease in aromaticity, humification, and molecular weight of sediment DOM in FT treatments. Also, high level of MPs was more likely to inhibit the formation of humic-like substances and tryptophan-like proteins. For DW and FT cycles, 0.1% and 1% PA MPs-treated sediments slightly increased the adsorption capacity of Cd(II), which may be ascribed to the aging of MPs. Further correlation analysis found that DW and FT altered the link between DOM indicators, and aggregate stability was directly related to the changes in sediment organic carbon. Our findings revealed the ecological risk of MPs accumulating in riparian sediments under typical hydrological processes.
RESUMO
In this study, the impact of surfactants on the adsorption behavior of Pb(II) onto microplastics-sediment (MPs-S) complexes was investigated. Firstly, virgin polyamide (VPA) and polyethylene (VPE) were placed in Xiangjiang River sediment for six months to conduct in-situ aging. The results indicated that the biofilm-developed polyamide (BPA) and polyethylene (BPE) formed new oxygen-containing functional groups and different biofilm species. Furthermore, the adsorption capacity of Pb(II) in sediment (S) and MPs-S complexes was in the following order: S > BPA-S > VPE-S > VPA-S > BPE-S. The addition of sodium dodecyl benzenesulfonate (SDBS) promoted the adsorption of Pb(II), and the adsorption amount of Pb(II) increased with the higher concentration of SDBS, while adding cetyltrimethylammonium bromide (CTAB) showed the opposite result. The adsorption process of MPs-S complexes to Pb(II) was dominated by chemical adsorption, and the interaction between MPs-S complexes and Pb(II) was multilayer adsorption involving physical and chemical adsorption when the surfactants were added. Besides, the pH exerts a significant effect on Pb(II) adsorption in different MPs-S complexes, and the highest adsorption amount occurred at pH 6. Noteworthy, CTAB promoted the adsorption ability of Pb(II) when the exogenous FA was added. The binding characteristic of sediment endogenous DOM components and Pb(II) was influenced by the addition of MPs and surfactants. Finally, it confirmed that adsorption mechanisms mainly involve electrostatic and hydrophobic interaction. This study provides a new perspective to explore the environmental behaviors of Pb(II) by MPs and sediments with the addition of surfactants, which was conducive to evaluating the ecological risks of MPs and heavy metals in aquatic environments.
RESUMO
Significant progress has been made in mitigating membrane biofouling by microbial quorum quenching (QQ). More efficient and survivable QQ strains need to be discovered. A new strain named Bacillus thuringiensis LZX01 was isolated in this study using a low carbon source concentration "starving" method from a membrane bioreactor (MBR). LZX01 secreted intracellular lactonase to enable QQ behavior and was capable of degrading 90 % of C8-HSL (200 ng/mL) within 30 min, which effectively delayed biofouling by inhibiting the growth of bacteria associated with biofouling and improving the hydrophilicity of bound extracellular polymeric substances. As a result, the membrane biofouling rate of MBR adding LZX01 was four times slower than that of the control MBR. Importantly, LZX01 maintains its QQ activity even in environments contaminated with typical toxic pollutants. Therefore, with high efficiency, toxicity resistance, and easy culture, LZX01 holds great potential and significant promise for biofouling control applications.
Assuntos
Bacillus thuringiensis , Incrustação Biológica , Incrustação Biológica/prevenção & controle , Percepção de Quorum , Reatores Biológicos/microbiologia , Matriz Extracelular de Substâncias Poliméricas , Membranas ArtificiaisRESUMO
The coexistence of microplastics (MPs) and heavy metals in sediments has caused a potential threat to sediment biota. However, differences in the effects of MPs and heavy metals on microbes and plants in sediments under different sediment conditions remain unclear. Hence, we investigated the influence of polyethylene (PE) and polylactic acid (PLA) MPs on microbial community structure, Pb bioavailability, and wheatgrass traits under sequential incubation of sediments (i.e., flood, drainage, and planting stages). Results showed that the sediment enzyme activities presented a dose-dependent effect of MPs. Besides, 10 % PLA MPs significantly increased the F1 fractions in three stages by 11.13 %, 30.10 %, and 17.26 %, respectively, thus resulting in higher Pb mobility and biotoxicity. MPs altered sediment bacterial composition and structures, and bacterial community differences were evident in different incubation stages. Moreover, the co-exposure of PLA MPs and Pb significantly decreased the shoot length and total biomass of wheatgrass and correspondingly activated the antioxidant enzyme activity. Further correlation analysis demonstrated that community structure induced by MPs was mainly driven by sediment enzyme activity. This study contributes to elucidating the combined effects of MPs and heavy metals on sediment ecosystems under different sediment conditions.
Assuntos
Sedimentos Geológicos , Chumbo , Microplásticos , Poluentes Químicos da Água , Sedimentos Geológicos/microbiologia , Chumbo/toxicidade , Microplásticos/toxicidade , Poluentes Químicos da Água/toxicidade , Microbiota/efeitos dos fármacos , Poliésteres , Polietileno/toxicidade , Inundações , Bactérias/efeitos dos fármacosRESUMO
Non-point source pollution from rainwater runoff presents a serious challenge for urban water management in many cities undergoing urbanization and experiencing climate change. To alleviate water resource conflicts in Changsha, China, this study comprehensively evaluated the pollution characteristics and first flush effect (FFE) of runoff from asphalt roads and colored steel plate roofs under seven rainfall events in April-May 2022. The runoff was collected and purified using bioretention ponds. The results showed that the peak runoff pollutant concentrations occurred within the first 20 min of runoff generation and then decreased to relatively stable levels, with maximum total suspended solids (TSS) concentration and chemical oxygen demand (CODCr) reaching 873.5 and 207.32 mg/L, respectively, for road runoff and 162 and 73.31 mg/L for roof runoff, respectively. The main pollutants were TSS and CODCr, followed by ammonia nitrogen (NH4+-N), nitrate nitrogen (NO3--N), total phosphorus (TP), and nitrite nitrogen (NO2--N). Concentrations of pollutants and FFE for roof runoff were lower than those for road runoff. Road runoff had a more obvious FFE for TP and NH4+-N, whereas the roof runoff showed the presence of TP and NO3--N. An important implication is that treating the first 30% of surface runoff from rainfall events with long antecedent dry days or high rainfall amounts is necessary to improve water quality before discharge or utilization. The study also found that road and roof runoff, after treatment with bioretention ponds, exhibit good water quality, thus, allowing their use as reclaimed water or for miscellaneous purposes in urban areas. Overall, this study provides useful information for designing management measures to mitigate runoff pollution and reuse in Changsha.
Assuntos
Poluentes Ambientais , Poluentes Químicos da Água , Monitoramento Ambiental/métodos , Poluentes Químicos da Água/análise , Movimentos da Água , Chuva , China , Qualidade da Água , Cidades , Fósforo/análise , Nitrogênio/análiseRESUMO
Current research focuses on efficient single-stage nitrogen removal from organic matter wastewater using the partial nitritation-anammox (PNA) process. In this study, we constructed a single-stage partial nitritation-anammox and denitrification (SPNAD) system using a dissolved oxygen-differentiated airlift internal circulation reactor. The system was operated continuously for 364 days at 250 mg/L NH4+-N. During the operation, the COD/NH4+-N ratio (C/N) was increased from 0.5 to 4 (0.5, 1, 2, 3, and 4), and the aeration rate (AR) gradually increased. The results showed that the SPNAD system maintained efficient and stable operation at C/N = 1-2 and AR = 1.4-1.6 L/min, with an average total nitrogen removal efficiency of 87.2%. The removal pathways of pollutants in the system and the interactions between microbes were revealed by analyzing the changes in sludge characteristics and microbial community structure at different phases. As the influent C/N increased, the relative abundance of Nitrosomonas and Candidatus Brocadia decreased, and that of denitrifying bacteria, such as Denitratisoma, increased to 44%. The nitrogen removal pathway of the system gradually changed from autotrophic nitrogen removal to nitrification-denitrification. At the optimum C/N, the SPNAD system synergistically removed nitrogen through PNA and nitrification-denitrification. Overall, the unique reactor configuration facilitated the formation of dissolved oxygen compartments, providing a suitable environment for different microbes. An appropriate organic matter concentration maintained the dynamic stability of microbial growth and interactions. These enhance microbial synergy and enable efficient single-stage nitrogen removal.
Assuntos
Desnitrificação , Nitrogênio , Nitrogênio/metabolismo , Oxirredução , Reatores Biológicos/microbiologia , Esgotos/microbiologia , Nitrificação , Interações MicrobianasRESUMO
To address the existing economic and environmental issues associated with swine wastewater (SW) treatment, a process combining up-flow anaerobic sludge blanket (UASB) and anaerobic membrane bioreactor (AnMBR) was developed and continuously operated for 137 d. Bioreactor conversion and microbial community dynamics in reactors were analyzed. The UASB-AnMBR process yielded excellent pollutants removal efficiencies of 96% and 63% for chemical oxygen demand (COD) and total phosphorous (TP), respectively. More than 60% of Firmicutes (Terrisporobacter, Turicibacter, and Clostridium sensu stricto 1), which were dominated by Methanosaeta and Methanobacterium with relative abundances of 58.6% and 36.8% in the UASB and 22.5% and 40.3% in the AnMBR, respectively, converted complex compounds into organic acids for methanogenesis. This research presented an analysis of pollutants removal and microbial dynamics of UASB-AnMBR, which significantly affected the large-scale application of UASB-AnMBR process.
Assuntos
Poluentes Ambientais , Microbiota , Purificação da Água , Animais , Suínos , Esgotos/microbiologia , Águas Residuárias , Eliminação de Resíduos Líquidos , Anaerobiose , Reatores Biológicos , MetanoRESUMO
In this study, the adsorption behavior of Pb(II) on natural-aged and virgin microplastics in different electrolyte solutions was investigated. The results demonstrated that natural-aged microplastics exhibited higher adsorption capacity for Pb(II) compared to virgin ones, and the addition of CaCl2 strongly inhibited the adsorption amount of Pb(II). The adsorption kinetics of Pb(II) adsorption were better fitted by the pseudo-second order model and Elovich equation, and were slowed down greatly at higher ionic strength. The rate-limiting steps of adsorption process were dominated by intra-particle diffusion. The adsorption isotherm of Pb(II) onto microplastics affected by salt ions can be well described by Freundlich model, the greater adsorption efficiency of natural-aged microplastics proved that adsorption process was multilayer and heterogeneous. In addition, pH significantly influenced the adsorption of Pb(II) due to the changes electrostatic interactions. The effect of fulvic acid in the electrolyte solutions was also revealed and attributed to the complexation with Na+ and Ca2+. Furthermore, the higher pH and ionic strength in different environmental water dramatically decreased adsorption capacity onto microplastics. Finally, it's confirmed that the adsorption mechanisms affected by salt ions mainly involve electrostatic interaction, surface complexation, and ionic exchange. These findings indicate that salt ions exert an important influence on the adsorption of heavy metals for MPs, which should be further concerned.
Assuntos
Microplásticos , Plásticos , Adsorção , Íons , ChumboRESUMO
Concentration polarization is an important issue in micellar enhanced ultrafiltration (MEUF) of wastewater containing heavy metal ions at low surfactant concentrations. In this paper, we studied removal of Cd(â ¡) by cross flow MEUF at low sodium dodecyl sulfate (SDS) concentration levels, and the role of concentration polarization in flux decline and Cd(â ¡) rejection was emphasized. Concentration polarization resistance and SDS concentration near membrane were calculated to characterize concentration polarization. The results showed that SDS concentration near membrane was 13â¯mM when feed concentration was merely 0.8â¯mM. By combining phase diagram of SDS, structures of SDS micelles in concentration polarization layer were deduced and thin layer structure transformed to porous structure formed by accumulated globular micelles when SDS concentration increased. Although micelles formed in concentration polarization layer was responsible for flux decline, they also provided adsorption sites for Cd(â ¡).
Assuntos
Cádmio/isolamento & purificação , Ultrafiltração/métodos , Águas Residuárias/química , Adsorção , Membranas Artificiais , Metais Pesados , Micelas , Dodecilsulfato de Sódio/química , Tensoativos/química , Ultrafiltração/instrumentaçãoRESUMO
Photocatalytic membranes (PMs), coupling of membrane filtration and photocatalysis, have exhibited the potential for application in the wastewater treatment. In this study, we firstly adopted the supramolecular aggregates of melamine (M), cyanuric acid (C), and urea (U) in specific dimethyl sulfoxide (DMSO) as precursors to prepare carbon nitride MCU-C3N4 with high photocatalytic performance, and a kind of novel-designed photocatalytic membrane was prepared via filtrating the mixture of graphene oxide (GO) nanosheets and MCU-C3N4 on PVDF membrane supports, and then crosslinked using glutaraldehyde (GA) to construct a steady coating on the GO/MCU-C3N4/PVDF membrane. GO/MCU-C3N4/PVDF composite membrane exhibited higher permeation flux than that of GO/PVDF membrane and exhibited excellent separation performance for oil-in-water emulsion. A visible light-driven self-cleaning four-stage filtration by a self-built dead-end filtration system was carried out to evaluate membrane antifouling property, and GO/MCU-C3N4/PVDF membrane (M2) possessed higher flux recovery ratio (FRR) (â¼92.36%) and lower irreversible fouling resistance (Rir) ratio (â¼8%) under 30min visible-light irradiation, maintaining relatively higher FRR (>72%) during 4 cycling of four-stage filtrating experiments. GO/MCU-C3N4/PVDF PMs are equipped with high permeation flux, separation performance, anti-fouling property and stability, indicating potential application in water treatment.
Assuntos
Filtração/instrumentação , Filtração/métodos , Glutaral/química , Grafite/química , Membranas Artificiais , Nitrilas/química , Polivinil/química , Purificação da Água/métodos , Catálise , Luz , Triazinas/químicaRESUMO
Quorum sensing (QS) is a process widely exist in bacteria, which refers to the cell-cell communication through secretion and sensing the specific chemical signal molecules named autoinducers. This review demonstrated recent research progresses on the specific impacts of signal molecules in the granular sludge reactors, such corresponding exogenous strategies contained the addition of QS signal molecules, QS-related enzymes and bacteria associated with QS process. Accordingly, the correlation between QS signaling molecule content and sludge granulation (including the formation and stability) was assumed, the comprehensive conclusion elucidated that some QS signals (acyl-homoserine lactone and Autoinducer 2) can accelerate the growth of particle diameter, the production of extracellular polymeric substance (EPS), microbial adhesion and change the microbiome structure. But diffusable signal factor (DSF) acted as a significant disincentive to the formation and stability of GS. As a result, it deserved serious attention on the value and role of QS signals in the GS. This review attempts to illuminate the potential method for addressing the main bottleneck: to accelerate the formation of granules and keep the high stability of GS for a long-term reactor. Therefore, review discussed the possible trends of GS: QS and intercellular/intracellular signaling which can lay a theoretical foundation for mechanism of GS formation and stability, would be of practical significance for further application in the future.
Assuntos
Percepção de Quorum/genética , Esgotos/químicaRESUMO
Surfactants widely exist in various kinds of wastewaters which could be treated by pressure-driven membrane separation (PDMS) techniques. Due to the special characteristics of surfactants, they may affect the performance of membrane filtration. Over the last two decades, there are a number of studies on treating wastewaters containing surfactants by PDMS. The current paper gives a review of the roles of surfactants in PDMS processes. The effects of surfactants on membrane performance were discussed via two aspects: influence of surfactants on membrane fouling and enhanced removal of pollutants by surfactants. The characteristics of surfactants in solution and at solid-liquid interface were summarized. Surfactants in membrane filtration processes cause membrane fouling mainly through adsorption, concentration polarization, pore blocking, and cake formation, and fouling degree may be influenced by various factors (feed water composition, membrane properties, and operation conditions). Furthermore, surfactants may also have a positive effect on membrane performance. Enhanced removal of various kinds of pollutants by PDMS in the presence of surfactants has been summarized, and the removal mechanism has been revealed. Based on the current reports, further studies on membrane fouling caused by surfactants and enhanced removal of pollutants by surfactant-aided membrane filtration were also proposed.
Assuntos
Filtração/métodos , Membranas Artificiais , Tensoativos/química , Eliminação de Resíduos Líquidos/instrumentação , Eliminação de Resíduos Líquidos/métodos , Adsorção , Incrustação Biológica , Filtração/instrumentação , Águas Residuárias/química , Poluentes Químicos da Água/química , Purificação da Água/métodosRESUMO
Recently, the application of membranes faces a big challenge due to membrane fouling, to alleviate this situation, the hybridization of photocatalysis and membrane filtration has aroused significant attention. In this study, we firstly introduced melamine, cyanuric acid and urea in dimethyl sulfoxide (DMSO) as precursors to fabricated the MCU(DMSO)-C3N4 material with excellent photocatalytic performance, and immobilized it on PVDF membranes by vacuum filtration, subsequently adding polyethylene glycol and glutaraldehyde as crosslinkers from MCU-C3N4/PVDF membrane. The results demonstrate that with the MCU-C3N4 ratio increasing, the membrane flux was gradually decreased. Besides, the photocatalytic efficiencies of MCU-C3N4/PVDF for rhodamine B (RhB) and tetracycline hydrochloride (TC) degradation are 84.24% and 71.26% respectively, which are about 8 times higher than that of the original membrane. To evaluate antifouling performance of photocatalytic membranes, we conducted a four-stage filtration system, and the flux recovery ratio (FRR) of MCU-C3N4/PVDF membranes reached over 80% (optimum 91%) under visible light irradiating (λâ¯>â¯420â¯nm) for 30â¯min. Meanwhile, under visible light irradiation reversible fouling (Rr) gradually became the dominant fouling factor instead of the irreversible fouling (Rir), indicating the excellent antifouling performance of MCU-C3N4/PVDF membranes. This novel method to modify membranes with MCU-C3N4 gives insight to photocatalytic and self-cleaning properties of photocatalytic composite membranes, providing theoretical basis for their broad application.
RESUMO
Quorum quenching (QQ) has been proved to be an efficient method to mitigate biofouling in membrane bioreactors (MBRs). In this paper, in order to enhance practicability of QQ microcapsules, we prepared three types microcapsules with same alginate cores (SAs). The microcapsules with polyacrylonitrile (PAN) layer showed excellent performance in preventing cell leakage from the microcapsules, increasing service life and improving mechanical strength. And confocal laser scanning microscopy images demonstrated that there were very little dead bacteria in the microcapsules with both chitosan and PAN layer than microcapsules with only PAN layer because chitosan layer can protect bacteria entrapped in cores from the hurt caused by poisonous PAN solution. At the same time, the microcapsules with PAN layer presented more efficient anti-biofouling ability in the physical washing test. At last, the bacterial microcapsules coated with both chitosan and PAN layer showed an obvious biofouling mitigation during the MBRs operation.