The influence of number of line pairs in digital intra-oral radiography on the detection accuracy of horizontal root fractures.

AIM: Line pairs are the unit for measurement of resolution and are related to the spatial quality of the system. Thus, the objective of this study was to evaluate the influence of number of line pairs in digital intra-oral radiography on the detection accuracy of horizontal root fractures. MATERIALS AND METHODS: Sixty-four extracted single-root human teeth were used. Thirty-two had horizontal root fractures created and were mounted in dry human mandibles. The teeth were radiographed with two digital receptors: the Digora Optime (14.3 lp mm-1) and the Digora Toto (26.3 lp mm-1). Images were viewed under standardized conditions by 3 calibrated examiners using the respective dedicated software (Digora for Windows 2.6(®) and Scanora(®) ). Digora Toto(®) images were also evaluated through the Digora for Windows 2.6(®) software. The results were statistically analyzed based on the area under the ROC curve for each examiner. RESULTS: Pairing Digora Toto(®) with Scanora(®) allowed for greater accuracy in horizontal root fractures diagnosis, while images acquired with that same system seem to lose accuracy when visualized with Digora for Windows 2.6(®) . Pairing Digora Optime(®) with Digora for Windows 2.6(®) resulted in the lowest accuracy for horizontal root fractures diagnosis. CONCLUSIONS: The higher number of line pairs and the consequent higher image resolution provided by the Digora Toto(®) system and its dedicated software seem to enhance the accuracy of horizontal root fractures diagnostic imaging.

Open apex type III dens invaginatus: a rare case report of an endodontic retreatment with an anatomical redesign.

Dens invaginatus is a critical condition for endodontic treatment. It frequently presents a complex internal anatomy and might be associated with incomplete root and apical development. This article presents one of the few reported cases of endodontic retreatment of Type III dens invaginatus. First, the internal anatomy was modified using burs under an operating microscope. Next, conventional chemical and mechanical preparation with hand files and 2.5% sodium hypochlorite was performed. Finally, an intracanal dressing with calcium hydroxide was used for nine months, at which point the anatomical features in the root canal system could be accessed. Adequate periradicular healing was observed and regression of the lesion was noted at the two-year follow-up. This case reinforces the idea that knowledge about the biologic aspects of endodontics, combined with adherence to technical standards, is helpful in resolving complex cases.

Does sodium thiosulphate avoid the formation of the brown-coloured precipitate as an intermediate irrigant between NaOCl and chlorhexidine?

This study evaluated the efficacy of sodium thiosulphate (ST) as an intermediate irrigant between sodium hypochlorite (NaOCl) and chlorhexidine (CHX) to avoid the formation of the brown-coloured precipitate. The in vitro experiment used microtubes to test the mixture of 2.5% NaOCl, 2% CHX and 5% ST solutions, varying their order and time of addition. In the ex vivo experiment, 10 bovine teeth were divided into two groups according to the intermediate irrigant used: distilled water (control) and 5% ST (experimental). Colour change occurred in all microtubes after interaction between solutions. While the precipitate was not observed in the experimental group, it was seen in all specimens of the control group. The 5% ST was able to prevent the formation of the brown-coloured precipitate in the ex vivo experiment, whereas it only prevented its in vitro formation when the waiting time for adding CHX was 10, 15 and 20 min.

Noncontact 3D evaluation of surface topography of reciprocating instruments after retreatment procedures.

This study evaluated the Reciproc R25 and Pro-R 25 instruments in unused condition, after one and a second use in endodontic retreatment employing a noncontact 3D light interferometer profiler, scanning electron microscopy (SEM) and cyclic fatigue tests. Twenty single-root teeth were instrumented with Reciproc R25 and filled with gutta-percha and sealer. A 3D profiler with a 20x objective using the Mx™ software was used to evaluate the cutting blade surfaces of Reciproc R25 and Pro-R 25 (n=5 per group) in unused condition, after the first and second uses in retreatment procedures. After retreatment, SEM was used to evaluate the topographic features of the used instruments. Cyclic fatigue tests were performed to compare new to used instruments. One-way ANOVA followed by Tukey test was used to compare the tested instruments before and after the first and second uses. Student t-test was used to compare the different instruments and for cyclic fatigue evaluation. No significant differences were observed in the cutting blade surfaces of Reciproc and Pro-R before and after one and two uses (p>0.05). Reciproc without use showed higher Sa and Sq when compared to Pro-R without use (p<0.05). No differences were observed between Reciproc and Pro-R after one and two uses (p>0.05). New and unused Reciproc showed longer time to fracture than Pro-R instruments (p<0.05), and only Pro-R showed differences between new and used instruments (p<0.05). Retreatment procedures with Reciproc and Pro-R did not change the surface topography of instruments. Reciproc had greater resistance to cyclic fatigue compared with Pro-R.

Cytotoxicity, and antimicrobial and physicochemical properties of sealers incorporated with Uncaria tomentosa.

This study evaluated the cytotoxicity, the antimicrobial and physicochemical properties of root canal sealers incorporated with phytotherapic Uncaria tomentosa (UT). Unmodified AH Plus (Dentsply, DeTrey, Germany) and MTA Fillapex (Angelus, Londrina, Brazil) were used as controls. UT was incorporated into AH Plus and MTA Fillapex, at concentrations of 2% and 5% of the total weight of these sealers (w/w). Flowability, setting time, and solubility were evaluated following ISO requirements. The pH values were measured at periods of 12, 24, 48 hours, and 7 days. The antimicrobial activity of the sealers against Enterococcus faecalis was analyzed by both direct contact tests in freshly prepared sealers, and after 7 days. The cytotoxicity of the samples was evaluated by the MTT assay, to check Balb/c 3T3 cell viability. The statistical analysis was performed by one-way ANOVA and Tukey's test (p < 0.05). The incorporation of UT was associated with a decrease in flow, for both sealers, an increase in AH Plus setting time, increase in MTA Fillapex pH values, and solubility (after 14 days), for both sealers (p < 0.05). Regarding the antibacterial evaluation, bacterial reduction was reported after incorporation of UT into both AH Plus and MTA Fillapex, up to 7 days after handling of the material (P<0.05). UT incorporation decreased the cytotoxic effects of both AH Plus and MTA Fillapex sealers in a way directly proportional to their respective concentrations (p < 0.05). In conclusion, UT can be added to both sealers to reduce their cytotoxicity, and improve their antibacterial effects, without compromising their original physicochemical properties.

Effects of clinical use of NiTi reciprocating instruments on cyclic and torsional resistance, and on roughness.

The aim of the present study was to evaluate the cyclic fatigue, torsional resistance and surface roughness of Reciproc R25 instruments in four different situations, namely as new instruments and as instruments tested after clinical preparation of one, two or three maxillary molars with four root canals. The total time required to perform each root canal preparation was recorded. Cyclic fatigue resistance was determined by the time to fracture using a customized testing device (n = 10 per group). The torsional test evaluated the torque and angle of rotation to failure according to ISO 3630-1 (n = 10 per group). The roughness of the working parts of new and used instruments was evaluated with a profilometer (n = 5 per group). Statistical analysis was performed using one-way ANOVA and Tukey's test. The level of significance was set at 5%. No fractures or deformations were observed after clinical use. Higher preparation time was needed during the third use of the instruments for all root canals (p < 0.05). There were no significant differences among the groups in regard to either cyclic fatigue or torsional resistance (p > 0.05). Regarding the roughness measurements, groove depth was higher on new and one- versus two- or three-maxillary-molar-prepared instruments (p < 0.05). It can be concluded that the clinical use of Reciproc instruments increased preparation time and decreased surface roughness. However, clinical use did not affect the cyclic fatigue or torsional resistance of the Reciproc instruments.

Postoperative pain after root canal filling with different endodontic sealers: a randomized clinical trial.

The aim of this randomized clinical trial was to compare the occurrence and intensity of postoperative pain and analgesic intake after root canal treatment, using different root canal sealers. Sixty single-rooted teeth diagnosed with asymptomatic necrosis and apical periodontitis were randomly assigned to 3 experimental groups (n=20), according to the root canal sealer: AH Plus, Endofill or MTA Fillapex. Endodontic treatment was performed in two sessions, and calcium hydroxide was used as the intracanal dressing. Patients were instructed to record pain intensity as none, slight, moderate and severe. Scores from 1 to 4 were attributed to each level of pain after 24 h, 48 h and 7 days. The need for analgesic intake was also recorded. Differences in the incidence of postoperative pain and the need for an analgesic were analyzed using the chi-square test. Differences in pain intensity after treatment were analyzed using the ordinal (linear) chi-square test. No significant differences were detected among the groups in terms of either incidence or intensity of postoperative pain, or need for analgesic intake, at any timepoint (p>0.05). No pain was reported after 7 days. AH Plus, Endofill and MTA Fillapex used for filling root canals resulted in the same rate of postoperative pain and need for analgesic medication.

Influence of chlorhexidine and zinc oxide in calcium hydroxide pastes on pH changes in external root surface.

The objective of this study was to assess the influence of chlorhexidine (liquid and gel) and zinc oxide in calcium hydroxide (CH) pastes on root pH in simulated external resorption. One hundred human anterior teeth with a single root canal were selected. After decoronation and root canal instrumentation, the specimens were divided into 4 experimental groups and 1 control group (without intracanal paste): CH + saline (CH+S), CH + 2% chlorhexidine liquid (CH+ CHX), CH + 2% chlorhexidine gel (CH+ CHXg), and CH + 2% chlorhexidine gel + zinc oxide (CH+ CHXg+ZnO). pH was measured using a microelectrode at 3 and 24 h, and 1, 2, 3, and 4 weeks after inserting intracanal pastes. Data were analyzed statistically using an ANOVA and Tukey's test (p < 0.05). The CH+CHXg+ZnO group had the highest pH values throughout (p<0.05). The CH+S and CH+ CHX groups had the highest pH values after 1 week and the CH+ CHXg group after 2 weeks. CH+ CHXg maintained the highest pH until the fourth week compared with CH+ CHX (p < 0.05). The control group remained at a neutral pH at all evaluated times. It can be concluded that chlorhexidine solution or gel maintained the alkaline pH of CH, and chlorhexidine gel allowed a slower decrease in pH over time. CH+ CHXg+ZnO showed the highest pH values and was an effective intracanal medication for maintaining alkaline root pH in the area of resorption.

Longevity of defective direct restorations treated by minimally invasive techniques or complete replacement in permanent teeth: A systematic review.

OBJECTIVES: This systematic review aimed to verify if there is difference in the longevity of minimally invasive techniques compared to the complete replacement for the treatment of defective direct restorations in permanent teeth. DATA: The data included randomized controlled clinical trials comparing the clinical performance of defective dental restorations treated by a complete replacement technique or minimally invasive techniques on permanent teeth. Evaluation of the risk of bias was performed using the Cochrane Collaboration common scheme for bias and the evidence was qualified using the GRADE tool. SOURCE: A comprehensive search was performed in the electronic databases: PubMed, Scopus, ISI Web of Science, The Cochrane Library, LILACS, BBO, SIGLE, followed by manual search in the reference lists of the included studies, without any restrictions. STUDY SELECTION: From 5554 retrieved studies, 10 met the eligibility criteria and were submitted to data extraction and quality assessment. The repair technique presented similar results to replacement and superior results when compared to sealing. In addition, refurbishment demonstrated to be a useful treatment for localized anatomical form defects. All the studies presented low risk of bias and high quality evidence for repair and refurbishment and moderate for the sealing technique. CONCLUSIONS: The direct restorations treated by the repair, seal and refurbishment techniques did not present a significant difference in clinical longevity in comparison to the replacement technique in permanent teeth with overall moderate quality of evidence. CLINICAL SIGNIFICANCE: The present findings demonstrated that the best treatment for defective restorations is conservative management. The evidence demonstrated here helps and encourages clinicians during the decision-making process. Moreover, it suggests not replacing imperfect restorations, but to managing them in a minimally invasive way, allowing the structure to be preserved.

Effect of Intermediate Flush Using Different Devices to Prevent Chemical Smear Layer Formation.

This study compared the effect of intermediate flush with distilled water delivered by conventional irrigation, EndoVac microcannula or Self-Adjusting File (SAF) system in the prevention of chemical smear layer (CSL) formation. Thirty human premolars were used. Canals were prepared with Reciproc system and 5.25% NaOCl. After chemomechanical preparation, samples were divided in 3 groups (n=10) according to the intermediate irrigation protocol with distilled water using: conventional irrigation, EndoVac microcannula or SAF. A final flush with 2% chlorhexidine solution was used and scanning electron microscopy was performed to assess protocol effectiveness. Two calibrated evaluators attributed scores according the presence or absence of CSL on the surface of the root canal walls at the coronal, middle and apical thirds, as follows: (1) no CSL; (2) small amounts of CSL; (3) moderate CSL; and (4) heavy CSL. Differences between protocols were analyzed with Kruskal-Wallis and Mann-Whitney U tests. Friedman and Wilcoxon signed rank tests were used for comparison between each root canal third. SAF resulted in less formation of CSL when compared with the conventional irrigation and EndoVac microcannula (p<0.05). When root canal thirds were analyzed, conventional irrigation and EndoVac groups showed less CSL formation at coronal and middle thirds in comparison to the apical third (p<0.05). In SAF group, there was no difference among the thirds (p>0.05). It may be concluded that an intermediate flush of distilled water, delivered by the SAF system resulted in a better reduction of CSL formation during chemomechanical preparation.

Micro-computed Tomography Assessment of Dentinal Micro-cracks after Root Canal Preparation with TRUShape and Self-adjusting File Systems.

INTRODUCTION: The aim of the present study was to evaluate the percentage frequency of dentinal micro-cracks observed after root canal preparation with TRUShape and Self-Adjusting File (SAF) systems by means of micro-computed tomography imaging analysis. A conventional full-sequence rotary system (BioRace) and a single-file reciprocation system (Reciproc) were used as reference techniques for comparison because of their known assertive cutting efficiency. METHODS: Forty anatomically matched mandibular incisors were selected, scanned at a resolution of 14.25 µm, and assigned to 4 experimental groups (n = 10), according to the preparation protocol: TRUShape, SAF, BioRace, and Reciproc systems. After the experimental procedures, the specimens were scanned again, and the registered preoperative and postoperative cross-section images of the roots (n = 70,030) were screened to identify the presence of dentinal micro-cracks. RESULTS: Overall, dentinal defects were observed in 28,790 cross-section images (41.11%). In the TRUShape, SAF, BioRace, and Reciproc groups, dentinal micro-cracks were visualized in 56.47% (n = 9842), 42.38% (n = 7450), 32.90% (n = 5826), and 32.77% (n = 5672) of the slices, respectively. All dentinal defects observed in the postoperative data sets were already present in the corresponding preoperative images. CONCLUSIONS: None of the preparation systems induced the formation of new dentinal micro-cracks.

Relationship between Initial Attendance after Dental Trauma and Development of External Inflammatory Root Resorption.

This clinical study aimed to evaluate the relationship of the delay between dental trauma and the initial attendance to the development of external inflammatory root resorption in permanent teeth affected by severe luxation. Sixty-seven patients, aged between 11 and 56 years, presenting 133 injured teeth with closed apex (56 extrusive luxation, 69 lateral luxation and 8 intrusive luxation) were followed up for a minimum of 24 months. The time elapsed between dental trauma and the initial attendance was recorded. The presence of necrotic pulp and external inflammatory resorption for each type of trauma was verified. Fisher's exact test was used to verify the influence of the initial attendance date at the Dental Trauma Center and the development of inflammatory resorption (p<0.05). The odds ratio was used to check the risk of developing external inflammatory resorption due to delay in seeking treatment. Pulp necrosis was observed in 105 teeth (78.9%) and external inflammatory resorption was detected in 17.8% cases of extrusive luxation (10 teeth), 15.9% of lateral luxation (11 teeth) and 25% of intrusive luxation (2 teeth). For lateral luxation, extended delay between the date of injury and initial attendance influenced the occurrence of external inflammatory resorption (p=0.0174). Patients who began treatment 45 days after the injury were 3.4 times more likely to develop external inflammatory resorption than patients who sought treatment after the trauma. Treatment late after the occurrence of dental trauma can impair the prognosis and result in the development of external inflammatory resorption in luxated teeth.

Noncontact 3D evaluation of surface topography of reciprocating instruments after retreatment procedures

Abstract This study evaluated the Reciproc R25 and Pro-R 25 instruments in unused condition, after one and a second use in endodontic retreatment employing a noncontact 3D light interferometer profiler, scanning electron microscopy (SEM) and cyclic fatigue tests. Twenty single-root teeth were instrumented with Reciproc R25 and filled with gutta-percha and sealer. A 3D profiler with a 20x objective using the Mx™ software was used to evaluate the cutting blade surfaces of Reciproc R25 and Pro-R 25 (n=5 per group) in unused condition, after the first and second uses in retreatment procedures. After retreatment, SEM was used to evaluate the topographic features of the used instruments. Cyclic fatigue tests were performed to compare new to used instruments. One-way ANOVA followed by Tukey test was used to compare the tested instruments before and after the first and second uses. Student t-test was used to compare the different instruments and for cyclic fatigue evaluation. No significant differences were observed in the cutting blade surfaces of Reciproc and Pro-R before and after one and two uses (p>0.05). Reciproc without use showed higher Sa and Sq when compared to Pro-R without use (p<0.05). No differences were observed between Reciproc and Pro-R after one and two uses (p>0.05). New and unused Reciproc showed longer time to fracture than Pro-R instruments (p<0.05), and only Pro-R showed differences between new and used instruments (p<0.05). Retreatment procedures with Reciproc and Pro-R did not change the surface topography of instruments. Reciproc had greater resistance to cyclic fatigue compared with Pro-R.

Resumo Este estudo avaliou os instrumentos Reciproc R25 e Pro-R 25 sem uso, após um primeiro e um segundo uso em retratamento endodôntico com perfilômetro 3D por interferometria de luz sem contato, microscópio eletrônico de varredura (MEV) e testes de fadiga cíclica. Vinte dentes unirradiculares foram instrumentados com Reciproc R25 e obturados com guta-percha e cimento endodôntico. Um perfilômetro 3D com uma objetiva 20x usando o software Mx ™ foi usado para avaliar as superfícies da lâmina de corte do Reciproc e Pro-R (n = 5 por grupo) na condição sem uso, após o primeiro e após um segundo uso em procedimentos de retratamento. Após retratamento, o MEV foi usado para avaliar as características topográficas dos instrumentos utilizados. Testes de fadiga cíclica foram realizados para comparar instrumentos novos com instrumentos usados. O teste One-way ANOVA seguido pelo teste de Tukey foi usado para comparar os instrumentos testados nos diferentes estágios. Para comparar os diferentes instrumentos e para avaliação de fadiga cílcica, foi utilizado o Student t-test. Não foram observadas diferenças estatisticamente significantes nas superfícies das lâminas de corte dos instrumentos Reciproc e Pro-R antes e após um e dois usos (p> 0,05). O Reciproc na condição sem uso apresentou maior Sa e Sq quando comparado ao Pro-R (p <0,05). Não foram observadas diferenças entre Reciproc e Pro-R após um e dois usos (p> 0,05). O Reciproc sem uso apresentou maior tempo de fratura do que os instrumentos Pro-R (p<0,05), e apenas o Pro-R apresentou diferenças entre instrumentos novos e usados (p<0,05). Os procedimentos de retratamento com Reciproc e Pro-R não alteraram a topografia da superfície dos instrumentos. Reciproc apresentou maior resistência à fadiga cíclica em comparação com o Pro-R.

Long-Term Cytotoxicity, pH and Dissolution Rate of AH Plus and MTA Fillapex.

The aim of the present study was to verify the long-term cytotoxic effects of the MTA Fillapex and to compare them with AH Plus. Dissolution rate and pH were also evaluated. Human osteoblast cells were incubated with elutes of fresh specimens from AH Plus and MTA Fillapex, and with elutes of the same specimens for 4 successive weeks. Elute's pH was evaluated at each time point. A multiparametric cell viability assay was performed. For dissolution rate, ISO methodology was used. The results were analyzed by one-way analysis of variance, complemented with the Tukey post-test (p<0.05). No significant difference was found among the materials when fresh mixed (p>0.05). After 1 week, AH Plus became non-cytotoxic on all three evaluated parameters. Conversely, MTA Fillapex remained severely and mildly cytotoxic over the entire experimental period (p<0.05). The dissolution rate of AH Plus was significantly lower than MTA Fillapex at all time points (p>0.05). The pH of AH Plus was significantly lower than MTA Fillapex at the second and third week (p<0.05). In the other tested time points no statistical difference was observed. In conclusion, MTA Fillapex remained cytotoxic after 4 weeks and its cytotoxicity may be related to the high dissolution rate of this material.

Cytotoxicity, and antimicrobial and physicochemical properties of sealers incorporated with Uncaria tomentosa

Abstract This study evaluated the cytotoxicity, the antimicrobial and physicochemical properties of root canal sealers incorporated with phytotherapic Uncaria tomentosa (UT). Unmodified AH Plus (Dentsply, DeTrey, Germany) and MTA Fillapex (Angelus, Londrina, Brazil) were used as controls. UT was incorporated into AH Plus and MTA Fillapex, at concentrations of 2% and 5% of the total weight of these sealers (w/w). Flowability, setting time, and solubility were evaluated following ISO requirements. The pH values were measured at periods of 12, 24, 48 hours, and 7 days. The antimicrobial activity of the sealers against Enterococcus faecalis was analyzed by both direct contact tests in freshly prepared sealers, and after 7 days. The cytotoxicity of the samples was evaluated by the MTT assay, to check Balb/c 3T3 cell viability. The statistical analysis was performed by one-way ANOVA and Tukey's test (p < 0.05). The incorporation of UT was associated with a decrease in flow, for both sealers, an increase in AH Plus setting time, increase in MTA Fillapex pH values, and solubility (after 14 days), for both sealers (p < 0.05). Regarding the antibacterial evaluation, bacterial reduction was reported after incorporation of UT into both AH Plus and MTA Fillapex, up to 7 days after handling of the material (P<0.05). UT incorporation decreased the cytotoxic effects of both AH Plus and MTA Fillapex sealers in a way directly proportional to their respective concentrations (p < 0.05). In conclusion, UT can be added to both sealers to reduce their cytotoxicity, and improve their antibacterial effects, without compromising their original physicochemical properties.

Effects of clinical use of NiTi reciprocating instruments on cyclic and torsional resistance, and on roughness

Abstrac The aim of the present study was to evaluate the cyclic fatigue, torsional resistance and surface roughness of Reciproc R25 instruments in four different situations, namely as new instruments and as instruments tested after clinical preparation of one, two or three maxillary molars with four root canals. The total time required to perform each root canal preparation was recorded. Cyclic fatigue resistance was determined by the time to fracture using a customized testing device (n = 10 per group). The torsional test evaluated the torque and angle of rotation to failure according to ISO 3630-1 (n = 10 per group). The roughness of the working parts of new and used instruments was evaluated with a profilometer (n = 5 per group). Statistical analysis was performed using one-way ANOVA and Tukey's test. The level of significance was set at 5%. No fractures or deformations were observed after clinical use. Higher preparation time was needed during the third use of the instruments for all root canals (p < 0.05). There were no significant differences among the groups in regard to either cyclic fatigue or torsional resistance (p > 0.05). Regarding the roughness measurements, groove depth was higher on new and one- versus two- or three-maxillary-molar-prepared instruments (p < 0.05). It can be concluded that the clinical use of Reciproc instruments increased preparation time and decreased surface roughness. However, clinical use did not affect the cyclic fatigue or torsional resistance of the Reciproc instruments.

Avaliação da citotoxicidade in vitro de diferentes pastas endodônticas utilizadas em odontopediatria / In vitro cytotoxic effects of different endodontic pastes used in pediatric dentistry

Objetivo: O presente estudo teve como objetivo avaliar o potencial citotóxico de três diferentes pastas endodônticas em cultura celular de osteoblastos humanos. Material e Métodos: As pastas endodônticas Calen PMCC (SSWhite Artigos Dentários LTDA, Rio de Janeiro, Brasil), Feapex (Fórmula e Ação, São Paulo, Brasil) e CTZ (Lenzafarm, Belo Horizonte, Brasil) foram preparadas e eluídas em meio de cultura celular durante 24 horas em estufa a 37°C e 5% de CO2. Foram realizadas quatro diluições distintas desses meios nas concentrações 1: 1, 1: 2, 1: 4 e 1: 8. Culturas de células de Osteoblastos Humanos da linhagem Saos-2 foram expostas a estas diluições durante 24 horas. O controle negativo foi realizado expondo as células ao meio de cultura sem contato com nenhuma pasta endodôntica. A citotoxicidade desses meios foi avaliada utilizando o ensaio MTT e os resultados foram transformados em porcentagens de células viáveis em relação ao grupo controle negativo. A análise estatística foi realizada com nível de significância de 5%, utilizando ANOVA seguido do teste de Tukey. Resultados: A viabilidade celular foi significativamente alterada de acordo com o material testado (p <0,05) e sua concentração (p <0,05). Em todas as concentrações testadas, a pasta Feapex apresentou maior viabilidade celular comparada aos demais materiais (p <0,05). Embora não tenha sido observada diferença estatisticamente significante entre a pasta Calen PMCC e a pasta CTZ nas concentrações de 1: 1 e 1: 2 (p> 0,05), a pasta CTZ apresentou maior citotoxicidade nas concentrações de 1: 4 e 1: 8 (p <0,05 ). De forma geral, a citotoxicidade diminuiu com o aumento da diluição do material. Conclusão: De acordo com os resultados do presente estudo, a pasta endodôntica Feapex parece ser a melhor opção para utilização entre as pastas analisadas, pois apresentou menor citotoxicidade que as pastas Calen PMCC e CTZ

Objective: The aim of the present study was to evaluate the cytotoxic potential of three different endodontic filling materials on human osteoblast cell cultures. Material and Methods: The endodontic pastes Calen PMCC (SSWhite Dental Articles LTDA, Rio de Janeiro, Brazil), Feapex (Formula and Action, São Paulo, Brazil) and CTZ (Lenzafarm, Belo Horizonte, Brazil) were eluted in cell culture medium during 24 hours in an oven at 37°C and 5% CO2. Four distinct dilutions of these media were performed at the concentrations 1:1, 1:2, 1:4 and 1:8. Cell cultures of Saos-2 Human Osteoblast-like were exposed to these dilutions for 24 hours. The negative control group was performed by exposing the cells to culture medium without contact with any endodontic paste. The cytotoxic potential of these media was evaluated using the MTT assay and the results were transformed into viable cell percentages in relation to the negative control group. Statistical analysis was submitted with a significance level of 5%, using univariate Analysis of Variance (ANOVA) followed by Tukey's test. Results: Cell viability was significantly altered according to the material tested (p<0.05) and its concentration (p<0.05). Feapex samples presented higher cell viability than the other materials in all concentrations tested (p<0.05). Although no statistically significant difference was observed between Calen PMCC paste and CTZ paste at concentrations of 1: 1 and 1: 2 (p>0.05), CTZ paste showed a higher cytotoxicity at concentrations of 1: 4 and 1: 8 (p<0.05). In general, cytotoxicity decreases with increasing material dilution. Conclusion: According to the results of the present study, Feapex endodontic paste seems to be the better option for use among the analyzed pastes, since it presented lower cytotoxicity than Calen PMCC and CTZ pastes

Comparison of the effects of TripleGates and Gates-Glidden burs on cervical dentin thickness and root canal area by using cone beam computed tomography.

UNLABELLED: The search for new instruments to promote an appropriate cervical preparation has led to the development of new rotary instruments such as TripleGates. However, to the best of the authors' knowledge, there is no study evaluating TripleGates effect on the "risk zone" of mandibular molars. OBJECTIVES: The aim of this study was to evaluate the effects of a crown-down sequence of Gates-Glidden and TripleGates burs on the remaining cervical dentin thickness and the total amount of dentin removed from the root canals during the instrumentation by using cone beam computed tomography. The number of separated instruments was also evaluated. MATERIAL AND METHODS: Mesial roots of 40 mandibular first molars were divided into 2 equal groups: crown-down sequence of Gates-Glidden (#3, #2, #1) and TripleGates burs. Cervical dentin thickness and canal area were measured before and after instrumentation by using cone beam computed tomography and image analysis software. Student's t-test was used to determine significant differences at p < 0.05. RESULTS: No significant differences (p > 0.05) were observed between the instruments, regarding the root canal area and dentin wall thickness. CONCLUSION: Both tested instruments used for cervical preparation were safe to be used in the mesial root canal of mandibular molars.

Efeito do consumo de álcool no desenvolvimento de lesão periapical induzida em ratos: uma análise microtomográfica / The Effect of Alcohol Consumption on the Development of Periapical Lesion Induced in Rats: a Micro-CT Analysis

Objetivo: O objetivo deste estudo foi avaliar a influência do consumo crônico de álcool no aumento da destruição óssea periapical em ratos. Material e métodos: Foram selecionados 12 ratos machos da linhagem Wistar, aleatoriamente divididos nos grupos controle e álcool (n=6). Os ratos do grupo álcool foram submetidos à auto-administração de solução alcoólica contendo 25% de álcool puro. O grupo controle recebeu apenas água filtrada durante o estudo. Após as 5 semanas de adaptação do grupo álcool, todos os ratos foram anestesiados e a polpa dos seus primeiros molares inferiores esquerdos foi exposta à cavidade oral para indução da lesão periapical. Após 28 dias de exposição pulpar, os ratos foram sacrificados por sobredose de anestesia, e suas mandíbulas foram removidas e seccionadas para avaliação microtomográfica. As hemimandíbulas esquerdas foram fixadas e escaneadas no microtomógrafo SkyScan 1173 (Bruker, Kontich, Belgium). O tamanho da lesão periradicular foi medido a partir das imagens de microtomografia computadorizada (micro-CT), onde foram calculados a área de superfície e o volume da lesão. Também foram avaliadas a taxa percentual de ganho de peso e a ingestão de sólidos/líquidos dos grupos. Os dados foram estatisticamente analisados utilizando o teste t de Student (p<0,05). Resultados: Os animais do grupo controle tiveram uma maior taxa percentual de ganho de peso corporal e de ingestão tanto de sólidos como de líquidos (p<0,05). As lesões periapicais apresentaram maior volume e maior área nos animais do grupo álcool, em comparação ao grupo controle (p<0,05). Conclusão: O consumo crônico de álcool contribuiu para o aumento da destruição óssea periapical em casos de periodontite apical.

Objective: the aim of this study was to evaluate the influence of alcohol consumption on the increase of periapical bone destruction in rats. Material and Methods: the sample included 12 Wistar male rats, randomly assigned into a control group and an alcohol group (n=6). Rats in the alcohol group were submitted to self-administration of a 25% pure alcoholic solution. The control group received only filtered water throughout the study. After 5 weeks of adaptation to the alcohol dose, all animals were anesthetized and the pulps of their mandibular left first molar were exposed to the oral cavity to induce periapical lesion. Twenty-eight days after the pulp exposure, those rats were euthanized due to overdose of anesthesia and their mandibles were removed and sectioned to obtain a micro-computed tomographic (micro-CT) scan. The rats' left hemimandibles were fixed and scanned on the SkyScan 1173 (Bruker, Konitch, Belgium) microtomograph. The size of the periradicular lesions was measured from the images obtained on the micro-CT and the surface area and volume were calculated. It was also evaluated the weight gain rate and the ingestion of solid/liquid of both groups. Data were analyzed by the Student's t-test (p<0.05). Results: the control group showed higher rates of weight gain and ingested more solid and liquid than the alcohol group (p<0.05). Periapical lesions found in the alcohol group had higher volume and surface area than the ones of the control group (p<0.05). Conclusion: the chronic consumption of alcohol contributed to the increase of periapical bone destruction in cases of apical periodontitis

Resistência de união à dentina de um material fotopolimerizável à base de silicato de cálcio e modificado por resina / Dentin bond strength of resin-modified light-curable calcium-silicate-based material

Objetivo: este estudo teve como objetivo comparar a resistência de união à dentina de um material à base de silicato de cálcio fotopolimerizável modificado por resina (TheraCal LC®; Bisco, Schaumburg, IL, EUA) com MTA branco (WMTA®; Angelus, Londrina, PR, Brasil). Materiais e Métodos: dezesseis incisivos superiores e caninos humanos foram selecionados e três discos de 1 mm foram obtidos a partir do terço médio de cada raiz. Na superfície coronal de cada disco, dois furos de 1,2 mm de largura foram perfurados na dentina. Em seguida, os buracos artificiais foram preenchidos com um dos materiais testados: WMTA® e TheraCal LC®. As fatias dentárias preenchidas foram armazenadas em uma solução salina tamponada com fosfato (PBS) (pH 7,2) por 7 dias a 37°C. Depois disso, a avaliação do push-out foi realizada com uma ponta do êmbolo de 1,0 mm. A carga foi aplicada a uma velocidade de 0,5 mm / min até o deslocamento do selador. Os resultados foram expressos em MPa. O teste U de Mann-Whitney foi aplicado para classificar os materiais quanto à resistência adesiva à dentina. O nível de significância foi estabelecido em = 5%. Resultados: todas as amostras apresentaram resultados de resistência de união à dentina mensuráveis e não ocorreram falhas prematuras. O TheraCal LC® demonstrou valores superiores de resistência de união à dentina quando comparado ao WMTA® (P<0,0001). Conclusões: existe uma vantagem do TheraCal LC® sobre o WMTA® no que diz respeito à resistência da união ao empurrar e, portanto, pode ser considerado um material reparador promissor e inovador

Objective: this study aimed to compare the dentin bond strength of a resin-modified light-curable calcium-silicate-based material (TheraCal LC®; Bisco, Schaumburg, IL, USA) with White MTA (WMTA®; Angelus, Londrina, PR, Brazil). Materials and Methods: sixteen human maxillary incisors and canines were selected and three 1-mm-discs were obtained from the middle third of each root. On the coronal surface of each disc, two 1.2-mm-wide-holes were drilled through the dentin. Then, artificial holes were filled with one of the tested materials: WMTA® and TheraCal LC®. The filled dental slices were stored in a phosphate-buffered saline (PBS) solution (pH 7.2) for 7 days at 37°C. After that, push-out assessment was performed with a 1.0-mm-plunger-tip. Load was applied at a crosshead speed of 0.5 mm/min until sealer displacement. The results were expressed in MPa. Mann-Whitney U test was applied to rank materials regarding dentin push-out bond strength. Significance level was set at a = 5%. Results: All specimens showed measurable results and no premature failure occurred. TheraCal LC® demonstrated superior push-out bond strength values to dentin when compared to WMTA® (P<0.0001). Conclusions: there is advantage of TheraCal LC® over WMTA® as regards to the push-out bond strength and, therefore it may be taken as a promising and innovative reparative material