Catholyte-Free Electrocatalytic CO2 Reduction to Formate.

Electrochemical reduction of carbon dioxide (CO2 ) into value-added chemicals is a promising strategy to reduce CO2 emission and mitigate climate change. One of the most serious problems in electrocatalytic CO2 reduction (CO2 R) is the low solubility of CO2 in an aqueous electrolyte, which significantly limits the cathodic reaction rate. This paper proposes a facile method of catholyte-free electrocatalytic CO2 reduction to avoid the solubility limitation using commercial tin nanoparticles as a cathode catalyst. Interestingly, as the reaction temperature rises from 303 K to 363 K, the partial current density (PCD) of formate improves more than two times with 52.9 mA cm-2 , despite the decrease in CO2 solubility. Furthermore, a significantly high formate concentration of 41.5 g L-1 is obtained as a one-path product at 343 K with high PCD (51.7 mA cm-2 ) and high Faradaic efficiency (93.3 %) via continuous operation in a full flow cell at a low cell voltage of 2.2 V.

Catalytic cracking of C5 raffinate to light olefins over phosphorous-modified microporous and mesoporous ZSM-5.

Phosphorous-modified microporous and mesoporous ZSM-5 catalysts (XP/C-ZSM5) were prepared with a variation of phosphorous content (X = 0.17, 0.3, 0.7, 1.4, and 2.7 wt%), and they were applied to the production of light olefins (ethylene and propylene) through catalytic cracking of C5 raffinate. The effect of phosphorous content on the physicochemical properties and catalytic activities of XP/C-ZSM5 catalysts was investigated. It was revealed that physicochemical properties of XP/C-ZSM5 catalysts were strongly influenced by phosphorous content. Strong acidity of XP/C-ZSM5 catalysts decreased with increasing phosphorous content. In the catalytic cracking of C5 raffinate, both conversion of C5 raffinate and yield for light olefins (ethylene and propylene) showed volcano-shaped curves with respect to strong acidity. This result indicates that strong acidity of XP/C-ZSM5 catalysts played an important role in determining the catalytic performance in the catalytic cracking of C5 raffinate. Among the catalysts tested, 0.3P/C-ZSM5 catalyst with moderate strong acidity showed the best catalytic performance.

In-Bi Electrocatalyst for the Reduction of CO2 to Formate in a Wide Potential Window.

The CO2 atmospheric concentration level hit the record at more than 400 ppm and is predicted to keep increasing as the dependence on fossil fuels is inevitable. The CO2 electrocatalytic conversion becomes an alternative due to its environmental and energy-friendly properties and benign operation condition. Lately, bimetallic materials have drawn significant interest as electrocatalysts due to their distinct properties, which the parents' metal cannot mimic. Herein, the indium-bismuth nanosphere (In16Bi84 NS) was fabricated via the facile liquid-polyol technique. The In16Bi84 NS exhibits exceptional performance for CO2 reduction to formate, with the faradaic efficiency (FE) approaching ∼100% and a corresponding partial current density of 14.1 mA cm-2 at -0.94 V [vs the reversible hydrogen electrode (RHE)]. Furthermore, the FE could be maintained above 90% in a wide potential window (-0.84 to -1.54 V vs the RHE). This superior performance is attributed to the tuned electronic properties induced by the synergistic interaction between In and Bi, enabling the intermediates to be stably adsorbed on the catalyst surface to generate more formate ions.

Investigation on Electroreduction of CO2 to Formic Acid Using Cu3(BTC)2 Metal-Organic Framework (Cu-MOF) and Graphene Oxide.

A recent class of porous materials, viz., metal-organic frameworks (MOFs), finds applications in several areas. In this work, Cu-based MOFs (Cu-benzene-1,3,5-tricarboxylic acid) along with graphene oxide, viz., Cu-MOF/GO, are synthesized and used further for reducing CO2 electrochemically. The reduction was accomplished in various supporting electrolytes, viz., KHCO3/H2O, tetrabutylammonium bromide (TBAB)/dimethylformamide (DMF), KBr/CH3OH, CH3COOK/CH3OH, TBAB/CH3OH, and tetrabutylammonium perchlorate (TBAP)/CH3OH to know their effect on product formation. The electrode fabricated with the synthesized material was used for testing the electroreduction of CO2 at various polarization potentials. The electrochemical reduction of CO2 is carried out via the polarization technique within the experimented potential regime vs saturated calomel electrode (SCE). Ion chromatography was employed for the analysis of the produced products in the electrolyte, and the results showed that HCOOH was the main product formed through reduction. The highest concentrations of HCOOH formed for different electrolytes are 0.1404 mM (-0.1 V), 66.57 mM (-0.6 V), 0.2690 mM (-0.5 V), 0.2390 mM (-0.5 V), 0.7784 mM (-0.4 V), and 0.3050 mM (-0.45 V) in various supporting electrolyte systems, viz., KHCO3/H2O, TBAB/DMF, KBr/CH3OH, CH3COOK/CH3OH, TBAB/CH3OH, and TBAP/CH3OH, respectively. The developed catalyst accomplished a significant efficiency in the conversion and reduction of CO2. A high faradic efficiency of 58% was obtained with 0.1 M TBAB/DMF electrolyte, whereas for Cu-MOF alone, the efficiency was 38%. Thus, the work is carried out using a cost-effective catalyst for the conversion of CO2 to formic acid than using the commercial electrodes. The synergistic effect of GO sheets at 3 wt % concentration and Cu+OH- interaction leads to the formation of formic acid in various electrolytes.

Mono- and dinuclear CuII complexes of the benzyldipicolylamine (BDPA) ligand: crystal structure, synthesis and characterization.

The crystal structures of mono- and dinuclear CuII trifluoromethanesulfonate (triflate) complexes with benzyldipicolylamine (BDPA) are described. From equimolar amounts of Cu(triflate)2 and BDPA, a water-bound CuII mononuclear complex, aqua(benzyldipicolylamine-κ3N,N',N'')bis(trifluoromethanesulfonato-κO)copper(II) tetrahydrofuran monosolvate, [Cu(CF3SO3)2(C19H19N3)(H2O)]·C4H8O, (I), and a triflate-bridged CuII dinuclear complex, bis(µ-trifluoromethanesulfonato-κ2O:O')bis[(benzyldipicolylamine-κ3N,N',N'')(trifluoromethanesulfonato-κO)copper(II)], [Cu2(CF3SO3)4(C19H19N3)2], were synthesized. The presence of residual moisture in the reaction medium afforded water-bound complex (I), whereas dinuclear complex (II) was synthesized from an anhydrous reaction medium. Single-crystal X-ray structure analysis reveals that the CuII centres adopt slightly distorted octahedral geometries in both complexes. The metal-bound water molecule in (I) is involved in intermolecular O-H...O hydrogen bonds with triflate ligands and tetrahydrofuran solvent molecules. In (II), weak intermolecular C-H...F(triflate) and C-H...O(triflate) hydrogen bonds stabilize the crystal lattice. Complexes (I) and (II) were also characterized fully using FT-IR and UV-Vis spectroscopy, cyclic voltammetry and elemental analysis.

Carbon Dioxide Sequestration by Using a Model Carbonic Anhydrase Complex in Tertiary Amine Medium.

Globally, the elevation of carbon dioxide (CO2 ) levels due to the anthropogenic effect poses a serious threat to the ecosystem. Hence, it is important to control and/or mitigate the level of CO2 in the atmosphere, which necessitates novel tools. Herein, it is proposed to improve CO2 sequestration by using model complexes based on the enzyme carbonic anhydrase (CA) in aqueous tertiary amine medium. The effect of substituents on the model CA model complexes on CO2 absorption and desorption was determined by using a stopped-flow spectrophotometer to follow pH changes through coupling to pH indicator and a continuous stirred-tank reactor (CSTR). The CO2 hydration rate constants were determined under basic conditions and compound 6, which contained a hydrophilic group, showed the highest absorption or hydration levels of CO2 (2.860×10(3) L mol(-1) s(-1) ). In addition, CSTR results for the absorption and desorption of CO2 suggest that simple model CA complexes could be used in post-combustion processing.

Microporous and mesoporous ZSM-5 catalyst for catalytic cracking of C5 raffinate to light olefins.

ZSM5 catalysts (PAM(X)-ZSM5) with micropores and mesopores were prepared using polyacrylamide (PAM) as a soft template at different PAM content (X = 0, 0.12, 0.25, 0.53, 0.64, and 0.78 wt%), and they were applied to the production of light olefins (ethylene and propylene) through catalytic cracking of C5 raffinate. The effect of PAM content of PAM(X)-ZSM5 catalysts on the physicochemical properties and catalytic activities was investigated. N2 adsorption-desorption isotherms of PAM(X)-ZSM5 catalysts exhibited a broad hysteresis loop at high relative pressure, indicating the existence of mesopores in the catalysts. It was found that the catalytic performance of PAM(X)-ZSM5 catalysts was closely related to the mesoporosity of the catalysts. Conversion of C5 raffinate and yield for light olefins showed volcano-shaped trends with respect to mesopore/micropore volume ratio of the catalysts. Thus, an optimal PAM content was required to achieve maximum production of light olefins through catalytic cracking of C5 raffinate over microporous and mesoporous PAM(X)-ZSM5 catalysts.