Analysis Method of Bending Effect on Transmission Characteristics of Ultra-Low-Profile Rectangular Microstrip Antenna.

With the advent of wearable communication devices, microstrip antennas have developed multiple applications due to their ultra-low-profile properties. Therefore, it is essential to analyze the problem of frequency shift and impedance mismatch when the antenna is bent. For the case of a rectangular patch antenna E-plane bent on the cylindrical surface, (1) this paper introduces the effective dielectric constant into the cavity model, which can accurately predict the resonance frequency of the antenna, and (2) according to the equivalent circuit model of the antenna resonance mode, the lumped element parameters are calculated based on the above effective dielectric constant, so that impedance characteristics and the S-parameter matching the port can be quickly constructed. From the perspective of circuit frequency characteristics, it explains the change in the transmission performance of the curved antenna. The experimental results show that the maximum difference between the experimental and theoretical calculation frequencies is less than 1%. These results verify the validity and applicability of the theory in the analysis of ultra-low-profile patch antennas and wearable electronic communication devices. It provides a theoretical basis for the fast impedance matching of patch antennas under different working conditions.

Efficient Sensor Placement Optimization for Shape Deformation Sensing of Antenna Structures with Fiber Bragg Grating Strain Sensors.

This paper investigates the problem of an optimal sensor placement for better shape deformation sensing of a new antenna structure with embedded or attached Fiber Bragg grating (FBG) strain sensors. In this paper, the deformation shape of the antenna structure is reconstructed using a strain⁻displacement transformation, according to the measured discrete strain data from limited FBG strain sensors. Moreover, a two-stage sensor placement method is proposed using a derived relative reconstruction error equation. In this method, the initial sensor locations are determined using the principal component analysis based on orthogonal trigonometric (i.e., QR) decomposition, and then a new location is sequentially added into the initial sensor locations one by one by minimizing the relative reconstruction error considering information redundancy. The numerical simulations are conducted, and the comparisons show that the proposed method is advantageous in terms of the sensor distribution and computational cost. Experimental validation is performed using an antenna experimental platform equipped with an optimal FBG strain sensor configuration, and the reconstruction results show good agreements with those measured directly from displacement sensors. The proposed method has a large potential for the strain sensor placement of complex structures, and the proposed antenna structure with FBG strain sensors can be applied to the future wing-skin antenna or flexible space-based antenna.

Analysis of Vibration Characteristics of Spatial Non-Uniform Tensioned Thin-Film Structures Based on the Absolute Nodal Coordinate Formulation.

Due to their lightweight characteristics, spatial thin-film structures can generate vibrations far exceeding their film thickness when subjected to external loads, which has become a key factor limiting their performance. This study examines the vibration characteristics of tensioned membrane structures with non-uniform elements subjected to impacts in air, leveraging the Absolute Nodal Coordinate Formulation (ANCF). This model takes into account the wrinkling deformation of thin films under pre-tension and incorporates it into the dynamic equation derived using the absolute node coordinate method. A detailed discussion was conducted on the influence of non-uniform elements, situated at different locations and side lengths, on the vibration characteristics of the thin film. The analytical results obtained from the vibration model were compared with the experimental results, validating the effectiveness of the vibration model. This provides a theoretical foundation for the subsequent vibration control of thin films.

Additive Manufacturing for Terahertz Metamaterials on the Dielectric Surface based on Optimized Electrohydrodynamic Drop-on-demand Printing Technology.

The conventional techniques used to fabricate terahertz metamaterials, such as photolithography and etching, face hindrances in the form of high costs, lengthy processing cycles, and environmental pollution. In contrast, electrohydrodynamic (EHD) drop-on-demand (DOD) printing technology holds promise as an additive manufacturing method capable of producing micrometer- and nanometer-scale patterns rapidly and cost-effectively. However, achieving stable large-area printing proves challenging due to issues related to charge accumulation in insulated substrates and inconsistent meniscus vibration. In this paper, a smooth bipolar waveform driving method is proposed aimed at solving the problems of charge accumulation on insulated substrates and poor print consistency. The method involves utilizing driving waveforms with opposite polarities for neighboring droplets, allowing the charges carried by the printed droplets to neutralize each other. Moreover, extending the duration of the high voltage rise and fall times enhances the consistency of meniscus motion, thereby improving the stability of printing. Through optimization of the printing parameters, droplets with a diameter of 1.37 µm and straight lines with a width of 3 µm were printed. Furthermore, this approach was employed to print terahertz metamaterial surface devices, and the performance of the metamaterial is in good agreement with the simulation results. These findings demonstrate that the method greatly improves the stability of EHD DOD printing, thereby advancing the application of the technology in additive processing at the micro- and nanoscale.

Waveform Design Method for Piezoelectric Print-Head Based on Iterative Learning and Equivalent Circuit Model.

Piezoelectric print-heads (PPHs) are used with a variety of fluid materials with specific functions. Thus, the volume flow rate of the fluid at the nozzle determines the formation process of droplets, which is used to design the drive waveform of the PPH, control the volume flow rate at the nozzle, and effectively improve droplet deposition quality. In this study, based on the iterative learning and the equivalent circuit model of the PPHs, we proposed a waveform design method to control the volume flow rate at the nozzle. Experimental results show that the proposed method can accurately control the volume flow of the fluid at the nozzle. To verify the practical application value of the proposed method, we designed two drive waveforms to suppress residual vibration and produce smaller droplets. The results are exceptional, indicating that the proposed method has good practical application value.

Design and Experiment Investigation on Soft Grippers with Modular Variable Stiffness Structure.

Soft grippers have good adaptability and flexibility for grasping irregular or fragile objects, and to further enhance their stiffness, soft grippers with variable stiffness have been developed. However, existing soft grippers with variable stiffness have the disadvantages of complex structure and poor interchangeability. Here, a soft gripper with modular variable stiffness is proposed that has flexible Velcro embedded in the bottom layer of the soft actuator and one side of the variable stiffness cavity respectively, and both the general and variable stiffness grasping modes are achieved by separation or combination. First of all, according to the neo-Hookean model and the assumption of constant curvature, a free bending model of the soft actuator is established and optimal structural parameters of the soft actuator are obtained by the Genetic Algorithm. Then, influence of the driving pressure on the soft actuator stiffness is investigated, and a mathematical model of the variable stiffness is established. Finally, correctness of the statics model and the stiffness model were verified by experiments. Experimental results indicate that the proposed soft gripper with modular variable stiffness structure has excellent adaptability and stability to different objects, outstanding load bearing capacity, and stiffness adjustment capability.

Metal Coating Synthesized by Inkjet Printing and Intense Pulsed-Light Sintering.

The inkjet printing of nanoparticle inks to produce metal coatings is low in manufacturing cost and high in efficiency compared to conventional methods such as electroplating and etching. However, inkjet-printed metal coatings require sintering to provide better metal conductivity and adhesion. Traditional sintering methods require high processing temperatures that can easily damage the coating substrate. In this study, an enhanced overall conductivity is achieved by sintering a nanoparticle metal coating with intense pulsed light. Metal coatings sintered using different parameters were characterized by a profilometer and a four-probe tester, which showed that the surface topographies differed with different sintering degrees. The adhesion of the metal coating was proportional to the pre-sintering temperature within the allowable range of the substrate. Finally, the optimization of the sintering process according to the experimental results improved both the electrical conductivity and adhesion of the metal coating. The optimized parameters were used to fabricate a microstrip antenna and perform the return loss test and microwave darkroom test. The results matched the simulation results well.