Pixelated transmission-mode diamond X-ray detector.

Fabrication and testing of a prototype transmission-mode pixelated diamond X-ray detector (pitch size 60-100 µm), designed to simultaneously measure the flux, position and morphology of an X-ray beam in real time, are described. The pixel density is achieved by lithographically patterning vertical stripes on the front and horizontal stripes on the back of an electronic-grade chemical vapor deposition single-crystal diamond. The bias is rotated through the back horizontal stripes and the current is read out on the front vertical stripes at a rate of ∼ 1 kHz, which leads to an image sampling rate of ∼ 30 Hz. This novel signal readout scheme was tested at beamline X28C at the National Synchrotron Light Source (white beam, 5-15 keV) and at beamline G3 at the Cornell High Energy Synchrotron Source (monochromatic beam, 11.3 keV) with incident beam flux ranges from 1.8 × 10(-2) to 90 W mm(-2). Test results show that the novel detector provides precise beam position (positional noise within 1%) and morphology information (error within 2%), with an additional software-controlled single channel mode providing accurate flux measurement (fluctuation within 1%).

Damage investigation on tungsten and diamond diffractive optics at a hard x-ray free-electron laser.

Focusing hard x-ray free-electron laser radiation with extremely high fluence sets stringent demands on the x-ray optics. Any material placed in an intense x-ray beam is at risk of being damaged. Therefore, it is crucial to find the damage thresholds for focusing optics. In this paper we report experimental results of exposing tungsten and diamond diffractive optics to a prefocused 8.2 keV free-electron laser beam in order to find damage threshold fluence levels. Tungsten nanostructures were damaged at fluence levels above 500 mJ/cm(2). The damage was of mechanical character, caused by thermal stress variations. Diamond nanostructures were affected at a fluence of 59 000 mJ/cm(2). For fluence levels above this, a significant graphitization process was initiated. Scanning Electron Microscopy (SEM) and µ-Raman analysis were used to analyze exposed nanostructures.

Fabrication of nitrogen vacancy color centers by femtosecond pulse laser illumination.

We report on a novel method to fabricate single, multiple and large-area high-density ensembles of nitrogen vacancy (NV) color centers in synthetic type Ib bulk diamond by femtosecond laser illumination. Electron beams generated in propagation of intense infrared laser pulses in air sputtered on a diamond sample under high temperature aroused by the laser illumination, creating NV color centers. Typical photoluminescence (PL) spectra of NV centers could be observed on the illuminated spots. Photon streams from individual photoluminescent points exhibited anti-bunching effect by the second-order correlation measurement, evidencing single and multiple photon-emitters around the laser illuminated spots.

Development of an amorphous selenium-based photodetector driven by a diamond cold cathode.

Amorphous-selenium (a-Se) based photodetectors are promising candidates for imaging devices, due to their high spatial resolution and response speed, as well as extremely high sensitivity enhanced by an internal carrier multiplication. In addition, a-Se is reported to show sensitivity against wide variety of wavelengths, including visible, UV and X-ray, where a-Se based flat-panel X-ray detector was proposed. In order to develop an ultra high-sensitivity photodetector with a wide detectable wavelength range, a photodetector was fabricated using a-Se photoconductor and a nitrogen-doped diamond cold cathode. In the study, a prototype photodetector has been developed, and its response to visible and ultraviolet light are characterized.

Complex refractive index variation in proton-damaged diamond.

An accurate control of the optical properties of single crystal diamond during microfabrication processes such as ion implantation plays a crucial role in the engineering of integrated photonic devices. In this work we present a systematic study of the variation of both real and imaginary parts of the refractive index of single crystal diamond, when damaged with 2 and 3 MeV protons at low-medium fluences (range: 10(15) - 10(17) cm(-2)). After implanting in 125 × 125 µm(2) areas with a scanning ion microbeam, the variation of optical pathlength of the implanted regions was measured with laser interferometric microscopy, while their optical transmission was studied using a spectrometric set-up with micrometric spatial resolution. On the basis of a model taking into account the strongly non-uniform damage profile in the bulk sample, the variation of the complex refractive index as a function of damage density was evaluated.

Dosimetric characterization of a synthetic single crystal diamond detector in clinical radiation therapy small photon beams.

PURPOSE: To determine the potentialities of synthetic single crystal diamond Schottky diodes for accurate dose measurements in radiation therapy small photon beams. METHODS: The dosimetric properties of a diamond-based detector were assessed by comparison with a reference microionization chamber. The diamond device was operated at zero bias voltage under irradiation with high-energy radiotherapic photon beams. The stability of the detector response and its dose and dose rate dependence were measured. Different square field sizes ranging from 1 × 1 cm(2) to 10 × 10 cm(2) were used during comparative dose distribution measurements by means of percentage depth dose curves (PDDs), lateral beam profiles, and output factors. The angular and temperature dependence of the diamond detector response were also studied. RESULTS: The detector response shows a deviation from linearity of less than ±0.5% in the 0.01-7 Gy range and dose rate dependence below ±0.5% in the 1-6 Gy∕min range. PDDs and output factors are in good agreement with those measured by the reference ionization chamber within 1%. No angular dependence is observed by rotating the detector along its axis, while ∼3.5% maximum difference is measured by varying the radiation incidence angle in the polar direction. The temperature dependence was investigated as well and a ±0.2% variation of the detector response is found in the 18-40 °C range. CONCLUSIONS: The obtained results indicate the investigated synthetic diamond-based detector as a candidate for small field clinical radiation dosimetry in advanced radiation therapy techniques.

Three dimensional laser microfabrication in diamond using a dual adaptive optics system.

Femtosecond laser fabrication of controlled three dimensional structures deep in the bulk of diamond is facilitated by a dual adaptive optics system. A deformable mirror is used in parallel with a liquid crystal spatial light modulator to compensate the extreme aberrations caused by the refractive index mismatch between the diamond and the objective immersion medium. It is shown that aberration compensation is essential for the generation of controlled micron-scale features at depths greater than 200 µm, and the dual adaptive optics approach demonstrates increased fabrication efficiency relative to experiments using a single adaptive element.

Tunable continuous-wave diamond Raman laser.

Continuous-wave operation of a diamond Raman laser, intracavity-pumped by a diode-pumped InGaAs semiconductor disk laser (SDL), is reported. The Raman laser, which utilized a 6.5-mm-long synthetic single-crystal diamond, reached threshold for 5.3 W of diode laser pump power absorbed by the SDL. Output power up to 1.3 W at the first Stokes wavelength of 1227 nm was demonstrated with excellent beam quality and optical conversion efficiency of 14.4% with respect to absorbed diode laser pump power. Broad tuning of the Raman laser output between 1217 and 1244 nm was achieved via intracavity tuning of the SDL oscillation wavelength.

A diamond target for megavoltage cone-beam CT.

PURPOSE: To determine the properties of a megavoltage cone-beam CT system using the unflattened beam from a sintered diamond target at 4 and 6 MV. METHODS: A sintered diamond target was used in place of a graphite target as part of an imaging beam line (an unflattened beam from a graphite target) installed on a linear accelerator. The diamond target, with a greater density than the graphite target, permitted imaging at the lower beam energy (4 MV) required with the graphite target and the higher beam energy (6 MV) conventionally used with the tungsten/stainless steel target and stainless steel flattening filter. Images of phantoms and patients were acquired using the different beam lines and compared. The beam spectra and dose distributions were determined using Monte Carlo simulation. RESULTS: The diamond target allowed use of the same beam energy as for treatment, simplifying commissioning and quality assurance. Images acquired with the diamond target at 4 MV were similar to those obtained with the graphite target at 4 MV. The slight reduction in low energy photons due to the higher-Z sintering material in the diamond target had minimal effect on image quality. Images acquired at 6 MV with the diamond target showed a small decrease in contrast-to-noise ratio, resulting from a decrease in the fraction of photons in the beam in the energy range to which the detector is most sensitive. CONCLUSIONS: The diamond target provides images of a similar quality to the graphite target. Diamond allows use of the higher beam energy conventionally used for treatment, provides a higher dose rate for the same beam current, and potentially simplifies installation and maintenance of the beam line.

Single photon emission from diamond nanocrystals in an opal photonic crystal.

We present the first optical measurement of a single nitrogen-vacancy (NV) center in a three-dimensional photonic crystal. The photonic crystal, fabricated by self-assembly of polystyrene microspheres, exhibits a photonic stopband that overlaps the NV photoluminescence spectrum. A modified emission spectrum and photon antibunching were measured from the NV centers. Time-resolved fluorescence measurements revealed a 30% increase in the source lifetime. Encapsulation of single NV centers in a three-dimensional photonic crystal is a step towards controlling emission properties of a single photon source.

Broadband coherent light generation in diamond driven by femtosecond pulses.

We demonstrate broadband light generation in diamond pumped by two-color femtosecond laser pulses. We find that phase matching plays a critical role in the output angle and frequency of the generated sidebands. When a third femtosecond probe pulse is applied to the crystal in the boxed Coherent anti-Stokes Raman Scattering geometry, a two-dimensional array of multi-color beams is generated through the Raman, four-wave mixing, and six-wave-mixing processes. We test the mutual coherence between the generated sidebands. Such coherence, maintained over the broad spectrum, opens possibilities for synthesis of subfemtosecond light waveforms.

Characterization of the ADII-33 diamond detector.

Dosimetry characteristics of the ADII-33 diamond detector were investigated. Sensitivity, stability, bias voltage, hardening, dose rate, energy dependence, and spatial resolution were examined. Current generated in the detector was found to be proportional to the bias voltage applied to the detector with stability degrading as a function of the bias voltage. The average current increased with increasing bias voltage. The statistical fluctuation in current was less than 0.3% regardless of the applied bias voltage. The optimal bias voltage, at which the current uncertainty is negligible, was found to be 125+/-25 V. The detector was hardened up to 85 kGy without significant degradation in output signal. A sub-linearity in the current as a function of dose rate was observed when the dose rate varied from 600.0 to 11.1 cGy/min. A fitting parameter of delta=0.978 was observed in the power relationship of IinfinityDdelta. When comparing the diamond detector readings to corrected ion chamber readings over a wide energy range of electron beams, differences of only 0.2% were observed suggesting no energy dependence for electron beam. PDD curves for a 10 x 10 cm2 field for 6 and 20 MV photon beams measured with the diamond detector and the farmer type ion chamber were also compared and they closely agreed up to a depth of 14 cm. Beyond a depth of 14 cm, diamond detector starts to overestimate the PDD curve reaching difference of 1.90% and 1.0% at 18 cm depth for 6 and 20 MV, respectively, to those values measured with the ion chamber. The diamond detector presents slightly better spatial resolution than the Exradin A16 microchamber. We conclude that at the optimal bias voltage, this new diamond detector is stable and the uncertainties in the current will not affect its suitability for clinical use. If compared against a calibrated ion chamber to correct any energy and dose rate dependence and considering any radiation damage effect, this diamond detector can be used to measure absolute and relative dose.

Radiation doses from low energy X-ray beams measured with synthetic diamond compared with calculated values obtained from the PENELOPE Monte Carlo code.

The utilization of a probe with synthetic diamond as the sensing material developed to measure radiation doses from mammography X-ray beams is described. The computer code system PENELOPE was used, with a geometry model simulating the experimental conditions, to compute the doses from the mammography X-ray beams to the diamond sensing material. The orientation of the diamond sensor to provide maximum absorption of the incident X-ray beam during exposure was also investigated using the PENELOPE code. The results from the theoretical model and experimental measurements are compared.

Refractive index variation in a free-standing diamond thin film induced by irradiation with fully transmitted high-energy protons.

Ion irradiation is a widely employed tool to fabricate diamond micro- and nano-structures for applications in integrated photonics and quantum optics. In this context, it is essential to accurately assess the effect of ion-induced damage on the variation of the refractive index of the material, both to control the side effects in the fabrication process and possibly finely tune such variations. Several partially contradictory accounts have been provided on the effect of the ion irradiation on the refractive index of single crystal diamond. These discrepancies may be attributable to the fact that in all cases the ions are implanted in the bulk of the material, thus inducing a series of concurrent effects (volume expansion, stress, doping, etc.). Here we report the systematic characterization of the refractive index variations occurring in a 38 µm thin artificial diamond sample upon irradiation with high-energy (3 MeV and 5 MeV) protons. In this configuration the ions are fully transmitted through the sample, while inducing an almost uniform damage profile with depth. Therefore, our findings conclusively identify and accurately quantify the change in the material polarizability as a function of ion beam damage as the primary cause for the modification of its refractive index.

An investigation of the role of defect levels on the radiation response of synthetic diamond crystals when used as sensors for the detection of mammography X-rays.

This study evaluates the role of defects on the performances of synthetic diamond sensors on exposure to mammography X-rays. Through systematic investigations, the main cause of instability of response of examined sensors necessitating pre-irradiation was isolated and ascribed to the presence of ambient light which has the effect of emptying shallow trapping levels. The changes in response between measurements in light and dark conditions varied from 2.8 ± 1.2% to 63.0 ± 0.3%. Sensitivities between 0.4 and 6.7nCGy-1mm-3 determined for the sensors varied with defect levels. The study indicates that differences in crystal quality due to the presence and influence of defects would cause a discrepancy in the dosimetric performances of various diamond detectors. Once a sensor plate is selected (based on the influence of defect levels) and coupled to the probe housing with the response of the diamond sensor stabilised and appropriately shielded from ambient light, daily priming is not needed.

Residual radioactivity of treated green diamonds.

Treated green diamonds can show residual radioactivity, generally due to immersion in radium salts. We report various activity measurements on two radioactive diamonds. The activity was characterized by alpha and gamma ray spectrometry, and the radon emanation was measured by alpha counting of a frozen source. Even when no residual radium contamination can be identified, measurable alpha and high-energy beta emissions could be detected. The potential health impact of radioactive diamonds and their status with regard to the regulatory policy for radioactive products are discussed.

Performance of CVD diamond as an optically and thermally stimulated luminescence dosemeter.

Diamond is a material with extreme physical properties. Its radiation hardness, chemical inertness and tissue equivalence qualify it as an ideal material for radiation dosimetry. In the present work, the optically stimulated luminescence (OSL) and thermoluminescence (TL) characteristics of a 10 microm thick CVD diamond (polycrystalline diamond films prepared by chemical vapor deposition) film were studied in order to test its performance as a beta radiation dosemeter. The TL response is composed of four main TL glow peaks; two of these are in the range of 150-200 degrees C and two additional peaks in the 250-400 degrees C temperature range. The integrated TL as a function of radiation dose is linear up to 100 Gy and increases with increasing dose exposure. The dose dependence of the integrated OSL exhibits a similar behavior. The observed OSL/TL behavior for the CVD diamond film clearly demonstrate its capability for applications in radiation dosimetry with special relevance in medical dosimetry owing to the diamond's intrinsic material properties.

Optical bleaching, TSL and OSL features of CVD diamond.

Luminescence and optical features of chemical vapour deposition (CVD) diamond have been studied in view of the potential application of this material in ionising radiation dosimetry field. For this purpose, thermally stimulated luminescence (TSL) and optically stimulated luminescence (OSL) techniques have been used. A large amount of work has emphasised the excellent dosimetric properties of CVD diamond. Nevertheless, TSL measurements showed that after irradiation, this material is extremely sensitive to ambient light and the stored dose information is drastically affected by optical bleaching. From OSL analysis, it follows that both types of processes (TSL and OSL) were characterised by the same excitation and emission spectra and that optical bleaching originated from a broad stimulation band lying from visible to near infrared with a continuous character.

On the dose response of some CVD diamond thermoluminescent detectors.

The linearity of dose response of chemical vapour deposition (CVD) diamonds grown at the Institute for Materials Research at Limburg University, Belgium, was investigated over a dose range relevant for radiotherapy. The following CVD diamonds were investigated: (1) a batch of square 3 x 3 mm2 detectors cut from a CVD wafer and (2) an as-grown CVD wafer of 6 cm diameter. A total of 20 CVD square detectors were irradiated with 137Cs gamma rays over the dose range from 200 mGy to 25 Gy. The CVD wafer, used as a large-area thermoluminescent (TL) detector, was exposed to a 226Ra needle. Very few square detectors showed linearity over a limited dose range, followed by saturation of the TL signal. The dose range of linearity was found to be strongly affected by the thermal annealing procedure of the detector. Owing to its high sensitivity and homogeneity of response, the large CVD diamond wafer was found to be very suitable as a large-area detector for 2-D dose mapping of the 226Ra brachytherapy source, possibly for Quality Assurance purposes.

Kerma rate effects on thermoluminescent response of CVD diamond.

The thermoluminescence (TL) response of chemical vapour deposition diamond is studied after X-irradiation (45 kV) at room temperature for various air kerma rates ranging from 0.7 to 100 Gy.min(-1). For a given air kerma, the TL signal as a function of air kerma rate exhibits large variations and is higher for low air kerma rates than for higher ones. In order to explain these results, the simplest energy-level scheme has been considered, that is, with only one electron trap and one recombination centre. Kinetic equations are numerically solved. Calculations are made for various electron-hole generation rates and show that the trap filling as a function of electron-hole generation rate follows, actually, the same evolution as the one of experimental TL response. The kerma rate effect on TL response is explained by the competitivity between the recombination and the trapping processes during irradiation.