الملخص
Objective:To explore the application value of whole-process ultrasound-guided percutaneous portal vein puncture islet transplantation.Methods:From October 2018 to May 2021, 16 diabetics underwent whole-process ultrasound-guided percutaneous portal vein puncture islet transplantation at First Affiliated Hospital of Sun Yat-sen University.The whole process was guided by ultrasound for completing percutaneous portal vein puncture catheterization, islet infusion monitoring, bleeding prevention and ablation hemostasis after bleeding.Results:Ten patients [8 males and 2 females with a mean age of(45.9±21.1)years]underwent 16 islet transplants, including one islet(5 cases), two islets(4 cases)and three islets(1 case). A single puncture was successfully performed without damage to other extrahepatic organs, persistent portal hypertension, portal vein embolism or infection.Bleeding at liver puncture site occurred in 3 cases and ultrasound radiofrequency ablation was performed for immediate hemostasis.Among them, postoperative blood glucose stabilized at 4~12 mmol/l post-operation.And 5 cases(31.3%)achieved insulin independence for>2 months and 10 cases(62.5%)lowered insulin dosage by>50% as compared with preoperative level.The level of fasting C-peptide recovered or was higher than normal in 10 cases(62.5%)and became obviously elevated in the remainders.In 11 cases(68.8%)of them, liver transaminase was briefly and mildly elevated post-operation, and no other complications were observed.Conclusions:The whole-process ultrasound-guided percutaneous portal vein islet transplantation is both safe and feseasible.It avoids the injury of transplanted kidney caused by contrast agent and radiological radiation to operator and patient.It is a method of islet transplantation worth a wider popularization.
الملخص
Objective:To explore the value of shear wave elastography imaging(SWE) in the diagnosis of renal allograft fibrosis and analyze its advantages and limitations.Methods:The renal allograft of 61 patients who underwent renal allograft biopsy from June 2019 to April 2020 in the First Affiliated Hospital of Sun Yat-sen University were included in this study. According to the Banff classification, there were 51 patients with mild-degree fibration(interstitial fibrosis/tubular atrophy, IFTA 0-Ⅰ), and 29 patients with moderate or severe-degree fibration(IFTA Ⅱ-Ⅲ). Two-dimensional ultrasound, color Doppler flow imaging, SWE and kidney function test performed. All the results were compared between the two groups. Diagnostic performance was evaluated by receiver operating characteristic (ROC) curve using pathology as gold standard. The sensitivity, specificity, positive predictive value and negative predictive value were calculated for the diagnosis of moderate or severe-degree fibration.Results:Compared to mild-degree fibration group, creatinine( P<0.001), glomerular filtration rate( P<0.001), RI of arcuate arteries( P=0.022) and SWE value( P<0.001) significantly increased in the moderate or severe-degree fibration group. There were significant correlations between IFTA and creatinine ( r s=0.488, P<0.001), glomerular filtration rate ( r s=-0.452, P<0.001), RI of arcuate arteries( r s=0.228, P=0.042), SWE value( r s=0.584, P<0.001). Taking the cutoff value of SWE value deduced by ROC curve as 21.7 kPa, the area under ROC curve was 0.827. The sensitivity, specificity, positive predictive value and negative predictive value were 86.2%, 74.5%, 61.0% and 89.7%, respectively. Conclusions:There is a good correlation between the SWE value and the degree of fibrosis in the transplanted kidney. SWE can be used to distinguish mild from moderate or severe fibrosis of renal allograft, providing a potential noninvasive method for the assessment of kidney allograft fibration.
الملخص
BACKGROUND:3D printing, a rapid prototyping technology, is considered to be one of the symbols of the third industrial revolution. There are many kinds of 3D printed materials, which have a wide range of clinical applications.OBJECTIVE: To systematically introduce 3D printed biological materials, to summarize the application advances of 3D printing technology in the printing and production of bone, artificial limbs, dentures, skin, blood vessels, stent, implant prosthesis, and tumor models, as well as to investigate the performance conditions of 3D printed biomaterials based on the advantages and disadvantages of the currently used biomaterials, in order to provide reference for future research.METHODS:A computer-based search of CNKI, Wanfang, VIP, CBM, PubMed was performed to search relevant articles published from 2010 to 2016, using the keywords of three-dimensional printing/3D printing/3-D printing; biomaterials; clinical application in Chinese and English, respectively.RESULTS AND CONCLUSION: Great progress in 3D printed biomaterials has been made. However, there are some defects in the existing printed materials, such as high cost, low printing precision and poor biodegradability. Only if the problem of materials is solved, can we continue to develop 3D printing technology. New breakthroughs in 3D printing in the field of medicine have been made, and new technologies and new materials have been applied in clinical practice. Systemic summarization of these application achievements of 3D printing in the field of medicine can provide reference for future medical research.