Clinical outcomes of ultrasonic subgingival debridement combined with manual root planing in severe periodontitis / 北京大学学报(医学版)

OBJECTIVE@#To compare the clinical effects of ultrasonic subgingival debridement and ultrasonic subgingival debridement combined with manual root planing on severe periodontitis and then to investigate the necessity and significance of manual root planing.@*METHODS@#Twenty-three patients with severe periodontitis participated in this split-mouth randomized-controlled clinical trial. Baseline examination and randomization were performed after supragingival scaling: each of the upper and lower jaws had a quadrant as the test group treated with ultrasonic subgingival debridement combined with manual root planing, whereas the other two quadrants were the control group treated with ultrasonic subgingival debridement. Treatment of each patient was at intervals of one week and completed in two visits. Clinical indicators concerning probing depth (PD), clinical attachment loss (CAL) and bleeding index (BI) were recorded at baseline and 1 month, 3 months, 6 months after treatment.@*RESULTS@#There was no significant difference of periodontal indicators between the test group and the control group at baseline. Both the test group and control group resulted in significant improvement of PD, CAL and BI. One and three months after treatment, reduction of PD in the test group was higher than that in the control group [1 month: (2.13±1.31) mm vs. (1.79±1.33) mm, P<0.01; 3 months: (2.46±1.33) mm vs. (2.17±1.38) mm, P<0.01] and reduction of CAL in the test group was higher than that in the control group [1 month: (1.89±2.03) mm vs. (1.65±1.93) mm, P<0.01; 3 months: (2.03±2.05) mm vs. (1.83±1.97) mm, P<0.05]. Six months after treatment, PD in the test group and the control group decreased by (2.52±1.40) mm and (2.35±1.37) mm respectively, and the improvement in the test group was significantly better than that in the control group (P<0.01). CAL in the test group and the control group decreased by (1.89±2.14) mm and (1.77±2.00) mm respectively, and there was no statistical difference between the groups. There was no significant difference in the changes of BI between the two groups 1, 3 and 6 months after treatment.@*CONCLUSION@#Ultrasonic subgingival debridement combined with manual root planing has more reduction in PD and CAL compared with ultrasonic subgingival debridement. Therefore, it is still necessary to use manual instruments for root planing following ultrasonic subgingival debridement.

Comparison of residual cement between CAD/CAM customized abutments and stock abutments via digital measurement in vitro / 北京大学学报(医学版)

OBJECTIVE@#To compare the residual cement between computer aided design/computer aided manufacturing customized abutments (CCA) and stock abutments (SA), and to evaluate the feasibility of digital measurement for residual cement volume by three-dimensional scanning.@*METHODS@#Twenty master models needed in this study were all taken from one 47-year-old patient with arrested periodontitis, who had already had an implant placed at his right upper central incisor site in the Department of Periodonto-logy, Peking University School and Hospital of Stomatology. After 4 weeks of soft tissue conditioning by means of customized healing abutment, the height of peri-implant soft tissue was measured, from the implant platform to mucosal margin, as 5 mm. Using customized impression coping, the impression was taken and twenty models were fabricated and allocated to 4 groups according to the type of abutments: CCA1 (5 mm transmucosal height CCA, with margin at tissue level), CCA2 (4 mm transmucosal height CCA, with 1 mm submucosal margin), SA1 (3 mm transmucosal height SA, with 2 mm submucosal margin) and SA2 (1 mm transmucosal height SA, with 4 mm submucosal margin). Crowns were cemented to the abutments, which were seated on the working models. Excess cement was removed by a prosthodontic specialist. Thereafter, the volume of residual cement was evaluated by using three-dimensional scanning technique. The area proportion of residual cement was calculated on photographs taken by a single lens reflex camera. The weight of residual cement was weighed by an analytical balance. And the correlation of residual cement volume data with residual cement area proportion or weight of residual cement acquired by traditional methods was analyzed.@*RESULTS@#Residual cement was observed on all the experiment samples. The residual cement volume of CCA was significantly less than that of SA [(0.635 3±0.535 4) mm3 vs. (2.293 8±0.943 8) mm3, P < 0.001]. Consistently, CCA had less residual cement area proportion and weight than those of SA [area proportion: 7.57%±2.99% vs. 22.68%±10.06%, P < 0.001; weight: (0.001 5±0.001 0) g vs. (0.003 7±0.001 4) g, P < 0.001]. The residual cement volume was strongly correlated with the residual cement area proportion and residual cement weight (r>0.75, P < 0.001).@*CONCLUSION@#These in vitro results suggest that CCA minimized the residual cement more effectively than SA. The method to digitally evaluate the residual cement volume is feasible, but its validity and reliability need to be further studied.

Influence of thread shapes of custommade root-analogue implants on stress distribution of peri-implant bone: A three-dimensional finite element analysis / 北京大学学报(医学版)

OBJECTIVE@#To explore the effects from the thread shapes of custom-made root-analogue implant (RAI) on distributions of von Mises stress around the peri-implant bone.@*METHODS@#Five one-stage RAI three-dimensional finite element (FE) models with different thread shapes (V-shaped design, square design, buttress design, reverse buttress design and none thread design) and congruent bone were created through reverse engineering technology. The data of the five models were imported into the FE analysis software to calculate. A force of 100 N was applied parallelly and of 45° to the implant axis respectively. Analysis was performed to evaluate the von Mises stress distributions at the peri-implant regions with the help of the Ansys 16 software.@*RESULTS@#The von Mises stresses distributed mostly at the implant cervical regions and the tip ends of the threads on the cortical bone under oblique loading, while on the cancellous bone, the stresses concentrated mostly on the implant lateral cervical regions, the tip ends of the threads and the apical regions. When under vertical loading, the von Mises stresses distributed mostly at the implant cervical regions on the cortical bone while at the tip ends of the threads and the lateral apical regions on the cancellous bone. The von Mises stresses were better distributed on the thread groups under both kinds of loadings compared with no thread design. But there was no obvious difference among the different thread groups. The concentrations of the von Mises stresses on the cancellous bone in the thread groups were mostly at the tip ends of the threads while less in the apical area. The von Mises stresses were better distributed on the cancellous bone on the other three thread designs than on square design.@*CONCLUSION@#Thread designs are advocated for the reason that adding thread designs to the RAI standard design will have a positive effect on stress distributions at the peri-implant regions and it will reduce the concentrations of von Mises stresses on the cortical bone. From the standpoint of the stress distribution, V-shaped design, buttress design and reverse buttress design are more suitable for RAI than square design. There is no difference of the distributions of the von Mises stresses in the RAI between different thread designs.