RÉSUMÉ
Los osteomas fronto-etmoidales son los tumores benignos más frecuentes de los senos paranasales, pudiendo evolucionar con complicaciones por compresión de estructuras adyacentes. Se presenta el caso de una paciente de 63 años de edad, que consultó por aumento de volumen nasofrontal, cefalea y diplopía. Tras el examen clínico, se evidenció una asimetría facial con lateralización del bulbo ocular derecho y exoftalmo. La tomografía de los senos paranasales mostró una lesión que ocupa parcialmente el seno frontal, etmoidal y parte de la cavidad nasal. Los cuidados anatómicos y planificación quirúrgica se desarrollaron en un modelo estereolitográfico mientras que la cirugía de exéresis total se realizó con ayuda del sistema piezoeléctrico. El examen histológico confirmó el diagnostico de osteoma. Se obtuvo una reconstrucción exitosa, recuperando totalmente simetría y función ocular.
Fronto-ethmoidal osteomas are the most frequent benign tumors of the paranasal sinuses, and may evolve with complications by compression of adjacent structures. The case is a 63-year-old female patient, who consulted about increased nasofrontal volume, headache and diplopia. After the clinical exam, she presented a facial asymmetry with lateralization of the right eyeball and exophthalmus. Computed tomography of the sinuses showed a lesion that partially occupies the frontal sinus, ethmoidal sinus and part of the nasal cavity. The anatomical care and surgical planning was developed in a stereolithographic model while the total excision surgery was performed with the help of the piezoelectric system. Histological examination confirmed the diagnosis of osteoma. A successful reconstruction is obtained, fully recovering symmetry and ocular function.
Sujet(s)
Humains , Femelle , Adulte d'âge moyen , Os ethmoïde/chirurgie , Sinus frontal/chirurgie , Ostéome/chirurgie , Tumeurs des sinus de la face/chirurgie , Piézochirurgie/méthodes , Chirurgie assistée par ordinateur , Os ethmoïde/anatomopathologie , Sinus frontal/anatomopathologie , Modèles anatomiques , Ostéome/anatomopathologie , Tumeurs des sinus de la face/anatomopathologie , Planification des soins du patientRÉSUMÉ
Objective:To discuss the accuracy of stereolithography (SLA)-3D printing model in orthopedics and maxillofacial surgery,and to clarify the reliability of its clinical application.Methods:A total of 33 cases of SLA-3D printing models were randomly included (10 long bones,13 irregular bones and 10 prostheses),and the CT scanning and three-dimensional reconstruction were performed.According to the clinical application characteristics of the models,the max height (MH),max length (ML),max width (MW),width of the trochlear (WT),length of the trochlear (LT),length of the glenoid cavity (LGC),width of the glenoid cavity (WGC),distance of pubic tubercle-anterior superior iliac spine (DPI),diameter of the acetabulum (DA),diameter of the marrow cavity (DMC),anterior height of right ramus (AHRR) and posterior height of right ramus (PHRR) were selected to measure the original data and model data,respectively.The absolute / relative errors were calculated.Intraclass correlation coefficient (ICC) was used to evaluate the consistency of the data.The three-dimensional error analysis of the prosthesis model was carried out.Results:There were no significant differences in the anatomical parameters except MW of irregular bone (P＞0.05) in 33 cases of SLA-3D printing model.The values of ICC were all greater than 0.950;the maximum values of absolute / relative errors were-0.58 mm and-1.37％,respectively;the maximum 3D error of prosthesis model was 0.237 mm,and the average value was 0.132 mm.Conclusion:The CT data of SLA-3D model is highly consistent with the original data,and it is accurate and reliable in the diagnosis and treatment of the diseases in orthopedics and maxillofacial surgery.
RÉSUMÉ
Objective:To discuss the accuracy of stereolithography (SLA)-3D printing model in orthopedics and maxillofacial surgery,and to clarify the reliability of its clinical application.Methods:A total of 33 cases of SLA-3D printing models were randomly included (10 long bones,13 irregular bones and 10 prostheses),and the CT scanning and three-dimensional reconstruction were performed.According to the clinical application characteristics of the models,the max height (MH),max length (ML),max width (MW),width of the trochlear (WT),length of the trochlear (LT),length of the glenoid cavity (LGC),width of the glenoid cavity (WGC),distance of pubic tubercle-anterior superior iliac spine (DPI),diameter of the acetabulum (DA),diameter of the marrow cavity (DMC),anterior height of right ramus (AHRR) and posterior height of right ramus (PHRR) were selected to measure the original data and model data,respectively.The absolute / relative errors were calculated.Intraclass correlation coefficient (ICC) was used to evaluate the consistency of the data.The three-dimensional error analysis of the prosthesis model was carried out.Results:There were no significant differences in the anatomical parameters except MW of irregular bone (P＞0.05) in 33 cases of SLA-3D printing model.The values of ICC were all greater than 0.950;the maximum values of absolute / relative errors were-0.58 mm and-1.37％,respectively;the maximum 3D error of prosthesis model was 0.237 mm,and the average value was 0.132 mm.Conclusion:The CT data of SLA-3D model is highly consistent with the original data,and it is accurate and reliable in the diagnosis and treatment of the diseases in orthopedics and maxillofacial surgery.