Stress distribution in peri-implant bone, implants, and prostheses: 3D-FEA of marginal bone loss and prosthetic design / Distribuição de estresse no osso peri-implantar, implantes e próteses: análise 3D-FEA de perda óssea marginal e design protético

Objective: In response to the demand for dental implants, extensive research has been conducted on methods for transferring load to the surrounding bone. This study aimed to evaluate the stresses on the peripheral bone, implants, and prostheses under scenarios involving of the following variables: prosthesis designs, vertical bone heights, load angles, and restorative materials. Material and Methods: Three implants were inserted in the premolar and molar regions (5-6-7) of the two mandibular models. Model 1 represented 0 mm marginal bone loss and Model 2 simulated 3 mm bone loss. CAD/CAM-supported materials, hybrid ceramic (HC), resin-nano ceramic (RNC), lithium disilicate (LiSi), zirconia (Zr), and two prosthesis designs (splinted and non-splinted) were used for the implant-supported crowns. Forces were applied vertically (90°) to the central fossa and buccal cusps and obliquely (30°) to the buccal cusps only. The stresses were evaluated using a three-dimensional Finite Element Analysis. Results: Oblique loading resulted in the highest stress values. Of the four materials, RNC showed the low stress in the restoration, particularly in the marginal area. The use of different restorative materials did not affect stress distribution in the surrounding bone. The splinted prostheses generated lower stress magnitude on the bone, and while more stress on the implants were observed. Conclusion: In terms of the stress distribution on the peri-implant bone and implants, the use of different restorative materials is not important. Oblique loading resulted in higher stress values, and the splinted prosthesis design resulted in lower stress (AU)

Objetivo: Em resposta à demanda por implantes dentários, extensa pesquisa foi realizada sobre métodos para transferir carga ao osso circundante. Este estudo buscou avaliar os estresses no osso periférico, implantes e próteses em cenários que envolvem as seguintes variáveis: designs de próteses, alturas ósseas verticais, ângulos de carga e materiais restauradores. Material e Métodos: Três implantes foram inseridos nas regiões dos pré-molares e molares (5-6-7) de dois modelos de mandíbula. O Modelo 1 representou perda óssea marginal de 0 mm e o Modelo 2 simulou perda óssea de 3 mm. Materiais suportados por CAD/CAM, cerâmica híbrida (HC), cerâmica nano-resina (RNC), dissilicato de lítio (LiSi), zircônia (Zr) e dois designs de próteses (sintetizadas e não-sintetizadas) foram utilizados para as coroas suportadas por implantes. Forças foram aplicadas verticalmente (90°) à fossa central e cúspides bucais e obliquamente (30°) apenas às cúspides bucais. Os estresses foram avaliados usando Análise de Elementos Finitos tridimensional. Resultados: Cargas oblíquas resultaram nos valores mais altos de estresse. Entre os quatro materiais, RNC mostrou baixo estresse na restauração, especialmente na área marginal. O uso de diferentes materiais restauradores não afetou a distribuição de estresse no osso circundante. Próteses sintetizadas geraram menor magnitude de estresse no osso, enquanto mais estresse nos implantes foi observado. Conclusão: Em termos de distribuição de estresse no osso peri-implantar e implantes, o uso de diferentes materiais restauradores não é crucial. Cargas oblíquas resultaram em valores mais altos de estresse, e o design de prótese sintetizada resultou em menor estresse. (AU)

Bone Regenerate Evaluation MethodsMétodos de avaliação do regenerado ósseo / Métodos de avaliação do regenerado ósseoBone Regenerate Evaluation Methods

Abstract Since its introduction by Ilizarov, the distraction osteogenesis technique has been used to treat trauma-related conditions, infections, bone tumors, and congenital diseases, either as methods of bone transport or elongation. One of the major dilemmas for the orthopedic surgeon who performs osteogenic distraction is establishing a reproducible method of assessing the progression of the osteogenesis, enabling the early detection of regenerate failures,inorder toeffectively interfereduring treatment, andtodeterminetheappropriate time to remove the external fixator. Several quantitative monitoring methods to evaluate the structural recovery and biomechanical properties of the bone regenerate at different stages,aswell as the bone healing process, are under study. These methods can reveal data on bone metabolism, stiffness, bone mineral content, and bone mineral density. The present review comprehensively summarizes the most recent techniques to assess bone healing during osteogenic distraction, including conventional radiography and pixel values in digital radiology, ultrasonography, bone densitometry and scintigraphy, quantitative computed tomography, biomechanical evaluation, biochemical markers, and mathematical models. We believe it is crucial to know the different methods currently available, and we understand that using several monitoring methods simultaneously can be an ideal solution, pointing to a future direction in the follow-up of osteogenic distraction.

Resumo Desde que foi descrita por Ilizarov, a técnica de osteogênese por distração tem sido utilizada para o tratamento de diversas condições relacionadas ao trauma, infecções, tumores ósseos edoenças congênitas, naforma detransporteou alongamento ósseo. Um dos dilemas mais comuns do cirurgião ortopédico que realiza distração osteogênica é o estabelecimentodeum método reprodutível deverificaçãoda progressão da osteogênese, que permita a detecção precoce de falhas no regenerado, para que se possa interferir de formaeficazduranteotratamento,bemcomodeterminarotempoapropriadoderemoção dofixadorexterno.Recentemente,váriosmétodosdemonitoramentoquantitativo,comos quais se poderia avaliar a recuperação da estrutura e as propriedades biomecânicas do regenerado ósseoemdiferentes estágios, alémdoprocessodecicatrização óssea, têm sido amplamente investigados. Por esses métodos, pode-se saber o conteúdo mineral ósseo, a densidade mineral óssea, a rigidez e o metabolismo ósseo. Nesta revisão, resumimos de forma abrangente as técnicas mais recentes para avaliar a cicatrização óssea durante a distração osteogênica, entre elas, métodos como aradiografia convencional e os valores de pixels em radiologia digital, a ultrassonografia, a densitometria e a cintilografia ósseas, a tomografia computadorizada quantitativa, a avaliação biomecânica, os marcadores bioquímicos e os modelos matemáticos. Consideramos fundamental o conhecimento dos diversos métodos à disposição atualmente e entendemos que a utilização de vários métodos de monitoramento simultaneamente possa ser uma solução ideal, que aponte para uma direção futura no seguimento da distração osteogênica.

Must a Knee with Anterior Cruciate Ligament Deficiency and High-grade Pivot Shift Test Present an Increase in Internal Rotation? / Um joelho com deficiência de ligamento cruzado anterior e alto grau no teste de pivot shift deve apresentar aumento de rotação interna?

Abstract Objective: Rupture of the anterior cruciate ligament (ACL) is one of the most common injuries in athletes and is often associated with damage to anterolateral structures. This combination of injuries presents itself clinically as a high-grade pivot shift test. The hypothesis of this study is that patients with ACL deficiency and high-grade pivot shift test should have an increased internal knee rotation. Methods: Twenty-two patients were tested. After effective spinal anesthesia, two tests were performed with the patient in supine position. First, the bilateral pivot shift test was performed manually, and its grade was recorded. Then, with the knee flexed to 90 degrees, the examiner drew the projection of the foot in a neutral position and in maximum internal rotation, and the angle of internal rotation was measured from the axes built between the central point of the heel and the hallux. Results: In the ACL-deficient knee, it was observed that there is a statistically significant average internal rotation (IR) delta of 10.5 degrees between the groups when not adjusted for age, and 10.6 degrees when adjusted for age. Conclusions: Knees with ACL deficiency and with pivot shift test grade I do not show increased internal rotation in relation to knees with intact ACL. Knees with ACL deficiency and with pivot shift test grades II and III show increased internal rotation in comparison to healthy knees.

Resumo Objetivo: A ruptura do ligamento cruzado anterior (LCA) é uma das lesões mais comuns em atletas e está frequentemente associada a danos nas estruturas anterolaterais. Esta combinação de lesões apresenta-se clinicamente como um teste de pivot shift de alto grau. A hipótese deste estudo é que pacientes com deficiência de LCA e teste de pivot shift de alto grau tenham aumento da rotação interna (RI) do joelho. Métodos: Vinte e dois pacientes foram testados. Após raquianestesia efetiva, foram realizados dois testes com o paciente em posição supina. Primeiro, o teste de pivot shift bilateral foi realizado manualmente e seu grau foi registrado. Em seguida, com o joelho flexionado a 90 graus, o examinador traçou a projeção do pé em posição neutra e em RI máxima e mediu o ângulo de RI a partir dos eixos construídos entre o ponto central do calcanhar e o hálux. Resultados: Joelhos com deficiência de LCA apresentam delta da RI média estatisticamente significativo de 10,5 graus entre os grupos sem ajuste de idade e de 10,6 graus com ajuste de idade. Conclusões: Joelhos com deficiência do LCA e teste de pivot shift de grau I não apresentam aumento da RI em relação aos joelhos com LCA íntegro. Joelhos com deficiência do LCA e teste de pivot shift de graus II e III apresentam RI em comparação aos joelhos saudáveis.

Study on injectable chitosan hydrogel with tendon-derived stem cells for enhancing rotator cuff tendon-to-bone healing / 中国修复重建外科杂志

OBJECTIVE@#To explore the effect of chitosan (CS) hydrogel loaded with tendon-derived stem cells (TDSCs; hereinafter referred to as TDSCs/CS hydrogel) on tendon-to-bone healing after rotator cuff repair in rabbits.@*METHODS@#TDSCs were isolated from the rotator cuff tissue of 3 adult New Zealand white rabbits by Henderson step-by-step enzymatic digestion method and identified by multidirectional differentiation and flow cytometry. The 3rd generation TDSCs were encapsulated in CS to construct TDSCs/CS hydrogel. The cell counting kit 8 (CCK-8) assay was used to detect the proliferation of TDSCs in the hydrogel after 1-5 days of culture in vitro, and cell compatibility of TDSCs/CS hydrogel was evaluated by using TDSCs alone as control. Another 36 adult New Zealand white rabbits were randomly divided into 3 groups ( n=12): rotator cuff repair group (control group), rotator cuff repair+CS hydrogel injection group (CS group), and rotator cuff repair+TDSCs/CS hydrogel injection group (TDSCs/CS group). After establishing the rotator cuff repair models, the corresponding hydrogel was injected into the tendon-to-bone interface in the CS group and TDSCs/CS group, and no other treatment was performed in the control group. The general condition of the animals was observed after operation. At 4 and 8 weeks, real-time quantitative PCR (qPCR) was used to detect the relative expressions of tendon forming related genes (tenomodulin, scleraxis), chondrogenesis related genes (aggrecan, sex determining region Y-related high mobility group-box gene 9), and osteogenesis related genes (alkaline phosphatase, Runt-related transcription factor 2) at the tendon-to-bone interface. At 8 weeks, HE and Masson staining were used to observe the histological changes, and the biomechanical test was used to evaluate the ultimate load and the failure site of the repaired rotator cuff to evaluate the tendon-to-bone healing and biomechanical properties.@*RESULTS@#CCK-8 assay showed that the CS hydrogel could promote the proliferation of TDSCs ( P<0.05). qPCR results showed that the expressions of tendon-to-bone interface related genes were significantly higher in the TDSCs/CS group than in the CS group and control group at 4 and 8 weeks after operation ( P<0.05). Moreover, the expressions of tendon-to-bone interface related genes at 8 weeks after operation were significantly higher than those at 4 weeks after operation in the TDSCs/CS group ( P<0.05). Histological staining showed the clear cartilage tissue and dense and orderly collagen formation at the tendon-to-bone interface in the TDSCs/CS group. The results of semi-quantitative analysis showed that compared with the control group, the number of cells, the proportion of collagen fiber orientation, and the histological score in the TDSCs/CS group increased, the vascularity decreased, showing significant differences ( P<0.05); compared with the CS group, the proportion of collagen fiber orientation and the histological score in the TDSCs/CS group significantly increased ( P<0.05), while there was no significant difference in the number of cells and vascularity ( P>0.05). All samples in biomechanical testing failed at the repair site during the testing process. The ultimate load of the TDSCs/CS group was significantly higher than that of the control group ( P<0.05), but there was no significant difference compared to the CS group ( P>0.05).@*CONCLUSION@#TDSCs/CS hydrogel can induce cartilage regeneration to promote rotator cuff tendon-to-bone healing.

Research progress on biomechanics for internal fixation in tibial plateau fracture / 中国修复重建外科杂志

OBJECTIVE@#To review the biomechanical research progress of internal fixation of tibial plateau fracture in recent years and provide a reference for the selection of internal fixation in clinic.@*METHODS@#The literature related to the biomechanical research of internal fixation of tibial plateau fracture at home and abroad was extensively reviewed, and the biomechanical characteristics of the internal fixation mode and position as well as the biomechanical characteristics of different internal fixators, such as screws, plates, and intramedullary nails were summarized and analyzed.@*RESULTS@#Tibial plateau fracture is one of the common types of knee fractures. The conventional surgical treatment for tibial plateau fracture is open or closed reduction and internal fixation, which requires anatomical reduction and strong fixation. Anatomical reduction can restore the normal shape of the knee joint; strong fixation provides good biomechanical stability, so that the patient can have early functional exercise, restore knee mobility as early as possible, and avoid knee stiffness. Different internal fixators have their own biomechanical strengths and characteristics. The screw fixation has the advantage of being minimally invasive, but the fixation strength is limited, and it is mostly applied to Schatzker typeⅠfracture. For Schatzker Ⅰ-Ⅳ fracture, unilateral plate fixation can be used; for Schatzker Ⅴand Ⅵ fracture, bilateral plates fixation can be used to provide stronger fixation strength and avoid the stress concentration. The intramedullary nails fixation has the advantages of less trauma and less influence on the blood flow of the fracture end, but the fixation strength of the medial and lateral plateau is limited; so it is more suitable for tibial plateau fracture that involves only the metaphysis. Choosing the most appropriate internal fixation according to the patient's condition is still a major difficulty in the surgical treatment of tibial plateau fractures.@*CONCLUSION@#Each internal fixator has good fixation effect on tibial plateau fracture within the applicable range, and it is an important research direction to improve and innovate the existing internal fixator from various aspects, such as manufacturing process, material, and morphology.

Finite element analysis of the stability of Mason type Ⅲ radial head fracture fixed with three cross-bridge headless compression screw and locking plate / 中国骨伤

OBJECTIVE@#To compare the biomechanical stability of three cross-bridge headless compression screws and locking plates in the fixation of Mason type Ⅲ radial head fractures by finite element method.@*METHODS@#Using reverse modeling technology, the radial CT data and internal fixation data of a healthy 25-year-old male were imported into the relevant software. Three-dimensional finite element model of 3 cross-bridge headless compression screws and locking plates for MasonⅢ radial head fractures were established, and the radial head was loaded with 100 N axial loading. The maximum displacement, maximum Von Mises stress and stress distribution of the two groups were compared.@*RESULTS@#The maximum displacements of the three cross-bridge screws group and locking plate group were 0.069 mm and 0.087 mm respectively, and the Von Mises stress peaks were 18.59 MPa and 31.85 MPa respectively. The stress distribution of the three screws group was more uniform.@*CONCLUSION@#Both internal fixation methods can provide good fixation effect. CoMPared with the locking plate fixation method, the 3 cross-bridge headless compression screws fixation is more stable and the stress distribution is more uniform.

Biomechanical parameters assessed during running among running-related athletes with recurrent hamstring strain injury: A scoping review

Background@#Hamstring strain injury (HSI) is the most common cause of missing practices and sporting events among running-related athletes. The incidence rate of recurrence in individuals with HSI ranges from 12% to 63%. While various risk factors for HSI have been identified, the alterations and role of biomechanical factors as potential causes of injury have been largely overlooked. @*Objectives@#To report the critical biomechanical parameters assessed among running-related athletes with a recurrent HSI and to present common testing protocols in assessing the biomechanical parameters among running-related athletes with a recurrent HSI. @*Methods@#Eligibility Criteria: Included studies investigated biomechanical parameters assessed among collegiate or elite running-related athletes with recurrent HSI. Sources of Evidence: This scoping review was registered in OSF and was conducted based on PRISMA-ScR. Six electronic databases were systematically searched from 1993 to May 2022. Charting Methods: The reviewers created a data charting tool for the scoping review.@*Results@#Out of 874 articles, a total of 10 articles were included in the scoping review. The critical biomechanical parameters assessed include trunk flexion, hip flexion, and knee extension angles (kinematic variables), flight and stance times and velocity (spatiotemporal variables), and EMG activity of biceps femoris, semitendinosus, semimembranosus, vastus lateralis, and rectus femoris, knee flexion and extension angle peak joint torque (kinetic variables). The most common running test protocols used were the 30-meter overground repeated sprint test, a percentage of maximum running velocity (treadmill), and repeated sprints on a non-motorized treadmill. The most common protocols for isokinetic muscle testing were 60 degrees (concentric), 300 degrees (concentric), and 180 degrees (eccentric) per second angular velocities.@*Conclusion@#The review demonstrated a need for more research on this topic, leading to only limited biomechanical parameters being discussed in the literature. This underscores the need for more rigorous research that could have practical applications for athletes and coaches.

Hipermovilidad del tercio posterior del menisco lateral secundario a lesión de los ligamentos meniscotibiales. Estudio cadavérico / Hypermobility of the posterior third of the lateral meniscus secondary to injury to the meniscotibial ligaments. Cadaveric study

Introducción: Los meniscos son estructuras semilunares formadas por fibrocartílagos, localizadas entre el fémur y la tibia. El menisco externo es más móvil, debido a sus inserciones a través de los ligamentos meniscotibiales y poplíteomeniscales. El menisco interno tiene un desplazamiento de 2-3 mm comparado con un desplazamiento de 9-10 mm del menisco externo. Se ha descripto en la literatura mundial que la hipermovilidad meniscal es secundaria a lesión de ligamentos poplíteomeniscales (principales estabilizadores), sin embargo, se realizó un estudio cadavérico donde se evidenció que los ligamentos poplíteomeniscales desempeñan un papel secundario. El objetivo de este estudio es demostrar que la lesión de los ligamentos meniscotibiales es la causante de la hipermovilidad meniscal externa.Materiales y métodos: se realizó un estudio cadavérico en 2022 en Arthrex, Naples, Florida, Estados Unidos. Previo a la valoración artroscópica se efectuó la sección de ligamentos meniscotibiales en el tercio posterior del menisco externo, manteniendo los ligamentos poplíteomeniscales y la inserción de la raíz posterior. Posteriormente, se efectuó la valoración artroscópica en la que se vio traslación anterior y superior del tercio posterior del menisco externo y se realizó la fijación meniscal.Resultados: mediante la fijación del tercio posterior del menisco lateral con técnica transósea, en una falla o insuficiencia de los ligamentos meniscotibiales, se logra estabilidad completa del menisco.Conclusión: la estabilidad principal del tercio posterior del menisco lateral está dada por la inserción periférica de los ligamentos meniscotibiales, por lo que la hipermovilidad meniscal externa no se debe a lesión de los ligamentos poplíteomeniscales. Nivel de Evidencia: IV

Introduction: The menisci are semilunar structures formed by fibrocartilage, located between the femur and the tibia. The lateral meniscus is more mobile due to its insertions through the tibial meniscus and popliteal meniscal ligaments. The medial meniscus has a displacement of 2-3 mm compared to a displacement of 9-10 mm for the external meniscus. It has been described in the world literature that meniscal hypermobility is secondary to injury to the popliteal meniscal ligaments (main stabilizers), however a cadaveric study was carried out where it was shown that the meniscal popliteal ligaments play a secondary role. The objective of this study is to demonstrate that injury to the meniscotibial ligaments is the cause of external meniscal hypermobility.Materials and methods: the cadaveric study was carried out in 2022 at Arthrex, Naples, Florida, United States. Prior to the arthroscopic evaluation, section of the meniscotibial ligaments was performed in the posterior third of the lateral meniscus, maintaining the popliteal meniscal ligaments and the posterior root insertion. Subsequently, the arthroscopic assessment is performed, showing anterior and superior translation of the posterior third of the external meniscus, and meniscal fixation is performed.Results: by fixing the posterior third of the lateral meniscus with a transosseous technique, in a failure or insufficiency of the meniscotibial ligaments, complete stability of the meniscus is achieved. Conclusion: the main stability of the posterior third of the lateral meniscus is given by the peripheral insertion of the meniscotibial ligaments, so external meniscal hypermobility is not due to injury to the popliteal meniscal ligaments. Level of Evidence: IV

The Influence of Morphological Characteristics on the Ball Throwing Velocity in the Professional Handball Players / Influencia de las Características Morfológicas en la Velocidad de Lanzamiento del Balón en los Jugadores Profesionales de Balonmano

SUMMARY: The aim of this study was to determine influence of upper limbs on the ball throwing velocity. A total of 10 professional handball players (25.74±4.84 years) participated in this study. All of them were playing in the top Montenegrin professional handball league. The results obtained in this study shows that upper limbs have high influence on ball throwing velocity. This study provides normative data and performance standards for professional handball. Coaches can use this information to determine the type of anthropometric characteristics that are needed for handball. Anthropometric parameters such as arm length, wrist diameter, hand length and arm span are the most relevant aspects related to ball throwing speed, given that these parameters cannot be changed through training, they should be taken into account when discovering talents.

El objetivo de este estudio fue determinar la influencia de los miembros superiores sobre la velocidad de lanzamiento de la pelota. En el estudio participaron un total de 10 jugadores profesionales de balonmano (25,74±4,84 años). Todos ellos jugaban en la principal liga profesional de balonmano de Montenegro. Los resultados obtenidos mostraron que los miembros superiores tienen una alta influencia en la velocidad de lanzamiento de la pelota. Este estudio proporciona datos normativos y estándares de rendimiento para el balonmano profesional. Los entrenadores pueden utilizar esta información para determinar el tipo de características antropométricas necesarias para el balonmano. Los parámetros antropométricos como la longitud del brazo, el diámetro de la muñeca, la longitud de la mano y la envergadura del brazo son los aspectos más relevantes relacionados con la velocidad de lanzamiento de la pelota, dado que estos parámetros no se pueden cambiar mediante el entrenamiento, deben tenerse en consideración a la hora de descubrir talentos.

Comportamiento Mecánico de un Premolar Humano Sano Sometido a Fuerzas Funcionales y Disfuncionales en un MEF / Mechanical Behavior of a Healthy Human Premolar Subjected to Functional and Dysfunctional Forces in a FEM

El propósito de este estudio fue analizar el comportamiento mecánico de la estructura dental sana de un primer premolar inferior humano sometido a fuerzas funcionales y disfuncionales en diferentes direcciones. Se buscó comprender, bajo las variables contempladas, las zonas de concentración de esfuerzos que conllevan al daño estructural de sus constituyentes y tejidos adyacentes. Se realizó el modelo 3D de la reconstrucción de un archivo TAC de un primer premolar inferior, que incluyó esmalte, dentina, ligamento periodontal y hueso alveolar considerando tres variables: dirección, magnitud y área de la fuerza aplicada. La dirección fue dirigida en tres vectores (vertical, tangencial y horizontal) bajo cuatro magnitudes, una funcional de 35 N y tres disfuncionales de 170, 310 y 445 N, aplicadas sobre un área de la cara oclusal y/o vestibular del premolar que involucró tres contactos estabilizadores (A, B y C) y dos paradores de cierre. Los resultados obtenidos explican el fenómeno de combinar tres vectores, cuatro magnitudes y un área de aplicación de la fuerza, donde los valores de esfuerzo efectivo equivalente Von Mises muestran valores máximos a partir de los 60 MPa. Los valores de tensión máximos se localizan, bajo la carga horizontal a 170 N y en el proceso masticatorio en la zona cervical, cuando la fuerza pasa del 60 %. Sobre la base de los hallazgos de este estudio, se puede concluir que la reacción de los tejidos a fuerzas funcionales y disfuncionales varía de acuerdo con la magnitud, dirección y área de aplicación de la fuerza. Los valores de tensión resultan ser más altos bajo la aplicación de fuerzas disfuncionales tanto en magnitud como en dirección, produciendo esfuerzos tensiles significativos para la estructura dental y periodontal cervical, mientras que, bajo las cargas funcionales aplicadas en cualquier dirección, no se generan esfuerzos lesivos. Esto supone el reconocimiento del poder de detrimento estructural del diente y periodonto frente al bruxismo céntrico y excéntrico.

SUMMARY: The purpose of this study was to analyze the mechanical behavior of the healthy dental structure of a human mandibular first premolar subjected to functional and dysfunctional forces in different directions. It was sought to understand, under the contemplated variables, the areas of stress concentration that lead to structural damage of its constituents and adjacent tissues. The 3D model of the reconstruction of a CT file of a lower first premolar was made, which included enamel, dentin, periodontal ligament and alveolar bone considering three variables: direction, magnitude and area of the applied force. The direction was directed in three vectors (vertical, tangential and horizontal) under four magnitudes, one functional of 35 N and three dysfunctional of 170, 310 and 445 N, applied to an area of the occlusal and/or buccal face of the premolar that involved three stabilizing contacts (A, B and C) and two closing stops. The results obtained explain the phenomenon of combining three vectors, four magnitudes and an area of force application, where the values of effective equivalent Von Mises stress show maximum values from 60 MPa. The maximum tension values are located under the horizontal load at 170 N and in the masticatory process in the cervical area, when the force exceeds 60%. Based on the findings of this study, it can be concluded that the reaction of tissues to functional and dysfunctional forces varies according to the magnitude, direction, and area of application of the force. The stress values turn out to be higher under the application of dysfunctional forces both in magnitude and in direction, producing significant tensile stresses for the dental and cervical periodontal structure, while under functional loads applied in any direction, no damaging stresses are generated. This supposes the recognition of the power of structural detriment of the tooth and periodontium against centric and eccentric bruxism.

Mechanical Evaluation of Different Stable Internal Fixation Techniques of Sagittal Osteotomy in Mandibular Advance / Evaluación Mecánica de Diferentes Técnicas de Fijación Interna Estable de Osteotomía Sagital en Avance Mandibular

The mandibular advancements performed in orthognathic surgeries can be stabilized with several techniques when using stable internal fixation. This study aims to comparatively evaluate, in vitro, the mechanical strength in a polyurethane mandibular model for four fixation techniques for sagittal split ramus osteotomy mandibular. 60 samples were divided into 4 groups, with 15 units for each group: group A, group B, group C and group D. Advances of 5 mm were made for each subgroup and fixed with 2.0 mm system plates and monocortical screws in the replicas of human hemimandibles in polyurethane resin. The samples were submitted to mechanical tests of linear loading, being evaluated the peak load and peak deformation. Technique B presented higher peak load (Kgf) and techniques A and B presented higher peak strain (p<0.05). Technique D presented lower peak load and lower peak strain (p<0.05). It is concluded that the study based on the development of new techniques for fixation for sagittal osteotomy of the mandibular ramus is of great importance for the advancement of orthognathic surgery, provided by the technical innovation of more favorable plate models.

Los avances mandibulares realizados en cirugías ortognáticas pueden estabilizarse con varias técnicas cuando se utiliza fijación interna estable. Este estudio tuvo como objetivo evaluar comparativamente, in vitro, la resistencia mecánica en un modelo mandibular de poliuretano para cuatro técnicas de fijación para la osteotomía sagital de la rama mandibular. Se dividieron 60 muestras en 4 grupos, con 15 unidades para cada grupo: grupo A, grupo B, grupo C y grupo D. Se realizaron avances de 5 mm para cada subgrupo y se fijaron con placas de sistema de 2,0 mm y tornillos monocorticales en las réplicas de hemimandíbulas humanas en resina de poliuretano. Las muestras fueron sometidas a pruebas mecánicas de carga lineal, siendo evaluadas la carga máxima y la deformación máxima. La técnica B presentó mayor pico de carga (Kgf) y las técnicas A y B presentaron mayor pico de deformación (p<0,05). La técnica D presentó menor carga máxima y menor tensión máxima (p<0,05). Se concluye que el estudio basado en el desarrollo de nuevas técnicas de fijación para la osteotomía sagital de la rama mandibular es de gran importancia para el avance de la cirugía ortognática, proporcionada por la innovación técnica de modelos de placas más favorables.

Biomechanical Behavior Evaluation of a Mandibular Full-Arch Implant-Supported Prosthesis on ZrO2 and TiO2 Monotype Dental Implants / Evaluación del Comportamiento Biomecánico de una Prótesis Implante Soportada de Arcada Completa Mandibular sobre Implantes Dentales Monotipos de ZrO 2 y TiO

This in silico study aimed to evaluate the biomechanical behavior of a full-arch implant-supported prosthesis on titanium and zirconia monotype implants. A 3D mandible containing 1.0 mm thick cortical and cancellous bone was modeled. Four dental implants (3.3 x 10 mm) were inserted into the jaw model in each model. The implants consisted of Titanium (Ti-S group) and Zirconia Monotype/one-piece (Zr-S group). Fixed full-arch implant-supported prostheses were cemented onto the implant. The models were exported to the analysis software and divided into meshes composed of nodes and tetrahedral elements. All materials were considered isotropic, elastic, and homogeneous. Therefore, all contacts were considered bonded, the mandible model was fixed in all directions, applying a static structural axial load of 300 N on the bottom of the fossa of the left mola r teeth. Microstrain and von-Mises stress (MPa) were adopted as failure criteria. Comparable stress and strain values were shown in the peri-implant bone for both groups. However, the Ti-S group presented a lower stress value (1,155.8 MPa) than the Zr-S group (1,334.2 MPa). Regarding bone tissues, the Ti-S group presented 612 µε and the Zr-S group presented 254 µε. The highest strain peak was observed in bone tissues around the implant closer to the load for both groups. Evaluating monotype zirconia and titanium implants, it is suggested that the greater the rigidity of the implant, the greater the concentration of internal stre sses and the less dissipation to the surrounding tissues. Therefore, monotype ceramic implants composed of yttrium-stabilized tetragonal polycrystalline zirconia may be a viable alternative to titanium implants for full-arch prostheses.

El objetivo de este estudio in silico fue evaluar el comportamiento biomecánico de una prótesis implanto soportada de arcada completa sobre implantes monotipo de titanio y zirconia. Se modeló una mandíbula en 3D que contenía tejido óseo cortical y esponjoso de 1,0 mm de espesor. En cada modelo, se insertaron cuatro implantes dentales (3,3 x 10 mm) en el modelo de mandíbula. Los implantes consistieron en Monotipo de Titanio y Zirconia. Sobre el implante se cementaron prótesis implanto soportadas de arcada completa fija. Los modelos se exportaron al software de análisis y se dividieron en mallas compuestas por nodos y elementos tetraédricos. Todos los materiales se consideraron isotrópicos, elásticos y homogéneos. Por lo tanto, todos los contactos se consideraron cementados, el modelo mandibular se fijó en todas las direcciones, aplicando una carga vertical estructural estática de 300 N en el fondo de la fosa de los dientes molares izquierdos. Se seleccionaron la microesfuerzo y la tensión de Von-Mises (MPa) como criterios de falla. Se mostraron valores de tensión y deformación comparables en el hueso periimplantario para ambos grupos. Sin embargo, el grupo Ti-S presentó un valor de estrés menor (1.155,8 MPa) que el grupo Zr-S (1.334,2 MPa). En cuanto a los tejidos óseos, el grupo Ti-S presentó 612 µε y el grupo Zr-S presentó 254 µε. La mayor concentración de deformación en el tejido óseo se observó en los tejidos alrededor del implante más cerca de la carga para ambos grupos. Al evaluar los implantes monotípicos de zirconia y titanio, se sugiere que cuanto mayor sea la rigidez del implante, mayor será la concentración de tensiones internas y menor la disipación a los tejidos circundantes. Por lo tanto, los implantes cerámicos monotipo compuestos de zirconia policristalina tetragonal estabilizada con itrio pueden ser una alternativa viable a los implantes de titanio para prótesis de arcada completa.

Biomechanical Effects of Angiotensin 1-7 in Diabetes Rats Femur / Efectos Biomecánicos de la Angiotensina 1-7 en el Fémur de Ratas Diabéticas

SUMMARY: It is known that diabetes mellitus has late complications, including microvascular and macrovascular diseases. Diabetes can affect bones through biochemical markers of bone structure, density, and turnover. This study aimed to biomechanically investigate the bone-protective effects of angiotensin 1-7 (Ang 1-7), one of the active peptides in the renin-angiotensin system, in rats with diabetes. Thirty male Wistar albino rats, three months old and weighing 250-300 g, were divided into four groups: diabetes, Ang 1- 7, diabetes plus Ang 1-7, and control. One month later, diabetes developed in rats; the rats were sacrificed, and their right femur was removed. Three-point bending biomechanical tests were performed on the femurs. The diabetic group had significantly higher bone fragility than the other groups (Pr >.05). Bone fragility was lower, and bone flexibility was higher in the Ang 1-7 groups (Pr>F value 0.05). As a result of our study, the effect of Ang 1-7 on the bones of rats with diabetes was investigated biomechanically. Ang 1-7 has a protective impact on the bones of rats with diabetes.

Se sabe que la diabetes mellitus tiene complicaciones tardías, incluyendo enfermedades microvasculares y macrovasculares. La diabetes puede afectar los huesos a través de los marcadores bioquímicos de la estructura, la densidad y el recambio óseo. Este estudio tuvo como objetivo investigar biomecánicamente los efectos protectores en los huesos de la angiotensina 1-7 (Ang 1-7), uno de los péptidos activos en el sistema renina-angiotensina, en ratas con diabetes. Treinta ratas albinas Wistar macho, de tres meses de edad y con un peso de 250-300 g, se dividieron en cuatro grupos: diabetes, Ang 1-7, diabetes más Ang 1-7 y control. Un mes después, se desarrolló diabetes en ratas; se sacrificaron los animales y se extrajo su fémur derecho. Se realizaron pruebas biomecánicas de flexión de tres puntos en los fémures. El grupo diabéticos tenía una fragilidad ósea significativamente mayor que los otros grupos (Pr > 0,05). La fragilidad ósea fue menor y la flexibilidad ósea fue mayor en los grupos Ang 1-7 (valor Pr>F 0,05). Como resultado de nuestro estudio, se determinó biomecánicamente el efecto de Ang 1-7 en los huesos de ratas con diabetes. Se concluye que Ang 1-7 tiene un impacto protector en los huesos de ratas diabéticas.

Biomechanical Gait Analysis in Patients with Osteonecrosis of the Femoral Head / Análise biomecánica da marcha de pacientes com osteonecrose da cabeça do fémur

Abstract Objectives Although osteonecrosis of the femoral head is a prevalent condition, its effects on gait parameters have not been thoroughly studied and are not well-established in the current literature. The primary aim of the present study is to describe gait in patients with a diagnosis of osteonecrosis. Methods This is a cross-sectional study. Nine patients diagnosed with osteonecrosis of the femoral head who were regularly followed-up at an outpatient clinic were selected for the present study and underwent gait analysis using Vicon Motion Capture Systems. Spatiotemporal data was obtained, and joint angles were calculated using an Euler angle coordinate system. Distal coordinate systems were used to calculate joint momentsand forceplatestoobtaingroundreactionforces. Results Patients with osteonecrosis presented with slower velocity (0.54 m/s ± 0.19) and smaller cadence (83.01 steps/min ± 13.23) than healthy patients. The pelvic obliquity range of motion was of 10.12° ± 3.03 and rotation was of 18.23° ± 9.17. The mean hip flexion was of 9.48° ± 3.40. Ground reaction forces showed reduced braking and propelling forces. Joint moments were reduced for flexion and adduction (0.42 Nm/kg ± 0.2 and 0.30 Nm/kg ± 0.11, respectively) but the abduction moment was increased (0.42 Nm/kg ± 0.18). Conclusions The present study showed that osteonecrosis of the femoral head presents compensatory gait mechanisms, with increased pelvic motion and decreased knee flexion to protect the hip joint. Decreased moments for hip flexion and adduction were also identified and muscle weakness for those groups may be correlated to the disease.

Resumo Objetivos Embora a osteonecrose da cabeça do fêmur seja uma lesão prevalente, seus efeitos sobre os parâmetros da marcha não foram minuciosamente estudados e não estão bem estabelecidos na literatura atual. O objetivo principal do presente estudo é descrever a marcha em pacientes com osteonecrose. Métodos Trata-se de um estudo transversal. Nove pacientes com diagnóstico de osteonecrose da cabeça do fêmur, sob acompanhamento regular em ambulatório, foram selecionados para o presente estudo e submetidos à análise da marcha com Vicon Motion Capture Systems. Os dados espaciais e temporais foram obtidos e os ângulos articulares foram calculados com o sistema de coordenadas angulares de Euler. Sistemas de coordenadas distais e plataformas de força foram utilizados para o cálculo de momentos articulares e de forças de reação ao solo, respectivamente. Resultados Os pacientes com osteonecrose apresentaram menor velocidade (0,54 m/s ± 0,19) e menor cadência (83,01 passos/minuto ± 13,23) do que pacientes saudáveis. As amplitudes de movimento de obliquidade e rotação pélvica foram de 10,12°± 3,03 e 18,23° ± 9,17, respectivamente. A média de flexão do quadril foi de 9,48° ± 3,40. O estudo das forças de reação ao solo revelou redução das forças de frenagem e propulsão. Os momentos articulares de flexão e adução caíram (0,42 Nm/kg ± 0,2 e 0,30 Nm/kg ± 0,11), mas o momento de abdução aumentou (0,42 Nm/kg ± 0,18). Conclusões O presente estudo mostrou que a osteonecrose da cabeça do fêmur é associada a mecanismos compensatórios da marcha, com aumento da movimentação pélvica e diminuição da flexão do joelho para proteção da articulação do quadril. A redução dos momentos de flexão e adução do quadril também foi identificada e a fraqueza destes grupos musculares pode estar correlacionada à doença.

Is there a Difference in Interfragmentary Compression Strength Between Fully or Partially Threaded Screws? Results of an Experimental Biomechanical Pilot Study / Há diferença na força de compressão interfragmentar entre parafusos com rosca total ou parcial? Resultados de um estudo biomecânico experimental piloto

Abstract Objective This study assessed differences between fully- and partially-threaded screws in the initial interfragmentary compression strength. Our hypothesis was that there would be an increased loss in initial compression strength with the partially-threaded screw. Methods A 45-degree oblique fracture line was created in artificial bone samples. The first group (FULL, n = 6) was fixed using a 3.5-mm fully-threaded lag screw, while the second group (PARTIAL, n = 6) used a 3.5-mm partially-threaded lag screw. Torsional stiffness for both rotational directions were evaluated. The groups were compared based on biomechanical parameters: angle-moment-stiffness, time-moment-stiffness, maximal torsional moment (failure load), and calibrated compression force based on pressure sensor measurement. Results After loss of one PARTIAL sample, no statistically significant differences in calibrated compression force measurement were observed between both groups: [median (interquartile range)] FULL: 112.6 (10.5) N versus PARTIAL: 106.9 (7.1) N, Mann-Whitney U-test: p = 0.8). In addition, after exclusion of 3 samples for mechanical testing (FULL n = 5, PARTIAL n = 4), no statistically significant differences were observed between FULL and PARTIAL constructs in angle-moment-stiffness, time-moment-stiffness, nor maximum torsional moment (failure load). Conclusion There is no apparent difference in the initial compression strength (compression force or construct stiffness or failure load) achieved using either fully-or partially-threaded screws in this biomechanical model in high-density artificial bone. Fully-threaded screws could, therefore, be more useful in diaphyseal fracture treatment. Further research on the impact in softer osteoporotic, or metaphyseal bone models, and to evaluate the clinical significance is required.

Resumo Objetivo Este estudo avaliou diferenças entre parafusos com rosca total ou parcial na resistência à compressão interfragmentar inicial. Nossa hipótese era de que haveria maior perda de resistência à compressão inicial com o parafuso de rosca parcial. Métodos Uma linha de fratura oblíqua de 45 graus foi criada em amostras de osso artificial. O primeiro grupo (TOTAL, n = 6) foi fixado com um parafuso de 3,5 mm de rosca total, enquanto o segundo grupo (PARCIAL, n = 6) usou um parafuso de 3,5 mm de rosca parcial. Avaliamos a rigidez à torção em ambas as direções de rotação. Os grupos foram comparados com base nos seguintes parâmetros biomecânicos: momento de rigidez-ângulo, momento de rigidez-tempo, momento de torção máxima (carga de falha) e força de compressão calibrada com base na medida do sensor de pressão. Resultados Depois da perda de uma amostra PARCIAL, não foram observadas diferenças estatisticamente significativas na força de compressão calibrada entre os 2 grupos [mediana (intervalo interquartil)]: TOTAL: 112,6 (10,5) N e PARCIAL: 106,9 (7,1) N, com p = 0,8 segundo o teste U de Mann-Whitney). Além disso, após a exclusão de 3 amostras para testes mecânicos (TOTAL, n = 5, PARCIAL, n = 4), não foram observadas diferenças estatisticamente significativas entre os construtos TOTAL e PARCIAL quanto ao momento de rigidez-ângulo, momento de rigidez-tempo ou momento de torção máxima (carga de falha). Conclusão Não há diferença aparente na força de compressão inicial (força de compressão ou rigidez do construto ou carga de falha) com o uso de parafusos de rosca total ou parcial neste modelo biomecânico em osso artificial de alta densidade. Parafusos de rosca total podem, portanto, ser mais úteis no tratamento de fraturas diafisárias. Mais pesquisas são necessárias sobre o impacto em modelos ósseos osteoporóticos ou metafisários de menor densidade e avaliação do significado clínico.

Monoaxial Mechanical Tests on Porcino Knee Ligaments / Ensaios mecânicos monoaxiais nos ligamentos do joelho porcino

Abstract The failure of ligament reconstruction has different risk factors, among which we can highlight the period before its incorporation, which is a mechanically vulnerable period. Loss of resistance over time is a characteristic of living tissues. Dissection with bone insertions of the cruciate ligaments of animal models is not described; however, it is essential for monoaxial assays to extract information from tests such as relaxation. The present work describes the dissection used for the generation of a test body for the performance of nondestructive tests to evaluate the mechanical behavior. We performed dissection of four porcino knee ligaments, proposing a dissection technique for the cruciate ligaments with bone inserts for comparison with collateral ligaments. The ligaments were submitted to relaxation tests and had strain gauges placed during the tests. The results showed viscoelastic behavior, validated by strain gauges and with a loss over time; with some ligaments presenting with losses of up to 20%, a factor to be considered in future studies. The present work dissected the four main ligaments of the knee demonstrating the posterior approach that allows maintaining their bone insertions and described the fixation for the monotonic uniaxial trials, besides being able to extract the viscoelastic behavior of the four ligaments of the knee, within the physiological limits of the knee.

Resumo A falha da reconstrução ligamentar tem diferentes fatores de risco, dentre os quais podemos destacar o período antes da sua incorporação, o qual configura um período mecânico vulnerável. A perda de resistência ao longo do tempo é uma característica dos tecidos vivos. A dissecção com as inserções ósseas dos ligamentos cruzados de modelos animais não é descrita; todavia, para os ensaios monoaxiais, é fundamental extrair as informações de ensaios como os de relaxação. O presente trabalho realiza a descrição da dissecção utilizada para a geração de corpo de prova para a realização de ensaios não destrutivos para avaliar o comportamento mecânico. Realizamos dissecção de quatro ligamentos de joelho porcino, propondo uma técnica de dissecção para os ligamentos cruzados com as inserções ósseas para comparação com os colaterais. Os ligamentos foram submetidos a testes de relaxação e foram colocadas strain gauges durante os testes. Os resultados mostraram comportamento viscoelástico, validado pelas strain gauges e com uma perda ao longo do tempo, sendo que, em alguns ligamentos, as perdas chegaram a até 20%, fator este a ser considerado em trabalhos futuros. O presente trabalho dissecou os quatro principais ligamentos do joelho, demonstrando a abordagem posterior que permite manter as suas inserções ósseas e descrevendo a fixação para os ensaios uniaxiais monotônicos, além de ter conseguido extrair o comportamento viscoelástico dos quatro ligamentos do joelho dentro dos limites fisiológicos do joelho.

Analysis of biomechanics in athletes with disabilities: a systematic and narrative review / Análise da biomecânica em atletas com deficiência: uma revisão sistemática e narrativa

Abstract Introduction Specifically in athletes with disabilities, investigations and biomechanical understanding seem to be even more relevant, as they provide data on how a certain type of disability limits sports practice and also describe parameters that allow the suggestion of relevant adaptations capable of guaranteeing a higher level comfort to practitioners. Objective To describe patterns of biomechanical behavior during exercise in athletes with disabilities, and to discuss possible relationships between the type of disability and the sport practiced. Methods This study performed a search in five electronic databases from the oldest records available until July 2020 using a search strategy that combined terms related to "athletes with disabilities" and "biomechanical analysis." Inclusion criteria: population (amateur or professional athletes with disabilities), intervention (sports practice), study design (observational), outcome (having evaluated biomechanics during sports practice). The biomechanical variables of interest included kinematic, kinetic, or electromyographic outcome measures. Results Tewnty-six articles met the inclusion criteria (n = 705 participants). Biomechanical analysis showed that there is a greater inclination in the angle of the head and an increase in the kinematic variables in blind athletes, which result in less distance, speed, and performance; compensatory body patterns, reduced mooring strength, speed, joint amplitude, and reduced final performance are observed in amputated limbs of amputees; and there was a strong correlation between the subject's functional classification and kinematic parameters in wheelchair athletes, with this being proportional to the level of impairment. Conclusion The outcomes demonstrated that the type of disability and the level of functional limitation are proportionally related to biomechanics in athletes with disabilities.

Resumo Introdução Em atletas com deficiência, as investigações e o entendimento biomecânico parecem ser ainda mais relevantes ao fornecer dados sobre de que modo determinado tipo de deficiência limita a prática esportiva e, ainda, descrever parâmetros que permitam sugestão de adaptações pertinentes capazes de garantir maior nível de conforto aos praticantes. Objetivo Descrever padrões de comportamento biomecânico durante o exercício em atletas com deficiência e discutir possíveis relações entre o tipo de deficiência e o esporte praticado. Métodos Este estudo realizou uma busca em cinco bases de dados eletrônicas a partir dos registros mais antigos disponíveis até julho de 2020, utilizando uma estratégia de busca que combinou termos relacionados a "atletas com deficiência" e "análise biomecânica". Critérios de inclusão: população (atletas amadores ou profissionais com deficiência), intervenção (prática esportiva), desenho do estudo (observacional), resultado (ter avaliado a biomecânica durante a prática esportiva). As variáveis biomecânicas de interesse incluíram medidas de desfecho cinemáticas, cinéticas ou eletromiográficas. Resultados Vinte e seis estudos atenderam aos critérios de inclusão (n = 705 participantes). Os resultados mostraram que há maior inclinação do ângulo da cabeça e aumento das variáveis cinemáticas em atletas cegos, resultando em menor distância, velocidade e desempenho; padrões corporais compensatórios, redução da força de amarração, velocidade, amplitude articular e desempenho final reduzido são observados em membros amputados de amputados; e parece haver relação entre a classificação funcional do sujeito e os parâmetros cinemáticos em atletas de cadeira de rodas, sendo esta proporcional ao grau de comprometimento. Conclusão Os resultados demonstraram que o tipo de deficiência e o nível de limitação funcional estão proporcionalmente relacionados à biomecâ-nica em atletas com deficiência.

Biomechanical analysis of narrow dental implants for maxillary anterior rehabilitation / Análise biomecânica de implantes de diâmetro reduzido para reabilitação da região anterior da maxila

Introdução: O conhecimento da biomecânica de implantes de diâmetro reduzido indica dimensões seguras para uso clínico. Objetivo: O objetivo do presente estudo foi comparar biomecanicamente implantes de diâmetro regular e reduzido para suporte de próteses implantossuportadas unitárias na região anterior da maxila por meio de análise de elementos finitos 3D (3D-FEA). Material e método: Quatro modelos 3D-FEA foram desenvolvidos a partir de recomposição de tomografia computadorizada e dados da literatura: um bloco ósseo na região incisiva lateral superior direita com implante e coroa. M1: 3,75 x 13 mm, M2: 3,75 x 8,5 mm, M3: 2,9 x 13 mm e M4: 2,9 x 8,5 mm. Foi aplicada carga de 178 N nos ângulos 0, 30 e 60 graus em relação ao longo eixo do implante. Foram avaliados mapas de tensão de Von Mises, tensão principal máxima e microdeformação. Resultado: M3 e M4 apresentaram maiores valores de tensão e microdeformação que M1 e M2, principalmente quando foram aplicadas forças inclinadas. Porém, M3 apresentou comportamento biomecânico melhor do que M4. Conclusão: Pode-se concluir que reduzir o diâmetro dos implantes pode prejudicar a biomecânica durante a aplicação de forças, mas a distribuição e intensidade das tensões, bem como os valores de microdeformação podem ser melhorados se o comprimento do implante for aumentado

Introduction: Narrow diameter implants biomechanics knowledge indicates safe dimensions for clinical use. Objective: Purpose of the present study was biomechanically to compare regular and narrow diameter implants to support single implant-supported prosthesis in the anterior region of the maxilla by 3D finite element analysis (3D-FEA). Material and method: Four 3D-FEA models were developed form CT scan recompositing and literature data: a bone block in the right upper lateral incisive region with implant and crown. M1: 3.75 x 13 mm, M2: 3.75 x 8.5 mm, M3: 2.9 x 13 mm and M4: 2.9 x 8.5 mm. It was applied load was of 178 N at 0, 30 and 60 degrees in relation to implant long axis. Von Mises stress, maximum principal stress and microdeformation maps were evaluated. Result: M3 and M4 did show higher tension and higher microdeformation values than M1 and M2, especially when inclined forces were applied. However, M3 presented enhanced biomechanical behavior than M4. Conclusion: It can be concluded that reduce the diameter of the implants can disadvantage to the biomechanics during the application of forces, but the distribution and intensity of the stresses, as well as the micro deformation values can be improved if the length of the implant is increased

Biomechanical evaluation of four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs

Purpose: This study compared, through biomechanical evaluation under ventral flexion load, four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs. Methods: In total, 28 identical atlantoaxial joint models were created by digital printing from computed tomography images of a dog, and the specimens were divided into four groups of seven. In each group, a different technique for ventral stabilization of the atlantoaxial joint was performed: transarticular lag screws, polyaxial screws, multiple screws and bone cement (polymethylmethacrylate­PMMA), and atlantoaxial plate. After the stabilization technique, biomechanical evaluation was performed under ventral flexion load, both with a predefined constant load and with a gradually increasing load until stabilization failure. Results: All specimens, regardless of stabilization technique, were able to support the predefined load without failing. However, the PMMA method provided significant more rigidity (p ≤ 0.05) and also best resisted the gradual increase in load, supporting a significantly higher maximum force (p ≤ 0.05). There was no statistical difference in flexural strength between the transarticular lag screws and plate groups. The polyaxial screws method was significantly less resistant to loading (p ≤ 0.05) than the other groups. Conclusions: The PMMA technique had biomechanical advantages in ventral atlantoaxial stabilization over the other evaluated methods.