摘要
Objective:To explore the optimal thermal effect parameter combination of An-pressing manipulation based on the pressing force, time and frequency, and to compare the thermal effect differences between the rhythmic and the continuous An-pressing manipulations. Methods:Three levels of light, moderate and heavy pressing forces were determined according to the An-pressing forces of the clinical tuina physicians; the pressing time and frequency parameters were determined according to the literatures about An-pressing manipulation. The volunteers were stimulated by the homemade An-pressing manipulation stimulator on the right Xinshu (BL 15), and then the three-factor and three-level orthogonal tests were carried out according to the test sequence specified by the L9(34) orthogonal table, and the temperature before and after pressing was recorded by an infrared thermal imaging system to screen the best parameters for the thermal effect of the An-pressing manipulation, thus to determine the optimal pressing parameters. The optimal parameters were then used for both continuous and rhythmic An-pressing manipulations to stimulate the bilateral Xinshu (BL 15). The temperature changes after pressing and the duration of the thermal effect (temperature difference ≤0.5℃ on both sides) were recorded by the infrared thermal imaging system, to explore the differences in the thermal effects of different An-pressing manipulations. Results:Among the three factors of pressing force, time and frequency, the influences of different pressing forces on temperature were significantly different (F=32.843,P=0.030), and the influence of 2.5 kg pressing force was the most significant; the effects of different pressing time on temperature were significantly different (F=54.102,P=0.018), and the pressing time of 7.5 min was the most significant; the influences of different pressing frequencies on temperature were not statistically significant (F=2.181,P=0.314), though the influence of 10 times/min pressing frequency was the largest. The influences on temperature difference of the rhythmic and the continuous An-pressing manipulations were significantly different (P=0.031 on the left side andP=0.045 on the right side), but there was no statistical difference in the duration of the thermal effect (P=0.690). Conclusion:The An-pressing manipulation parameters that significantly affect the temperature difference are pressing force and time. The optimal combination of thermal effect parameters is pressing force of 2.5 kg, time of 7.5 min, and frequency of 10 times/min. The local thermal effect of the rhythmic An-pressing manipulation is significantly greater than of the continuous An-pressing manipulation.
摘要
Objective:To observe the effect of An-pressing manipulation on biceps brachii with delayed onset muscle soreness (DOMS) in healthy male volunteers.Methods:A total of 30 male college student volunteers were randomly divided into a blank group,a model group and a treatment group,10 cases in each group.Subjects in the blank group did not receive any intervention;subjects in the model group received active weight-bearing eccentric exercise on the non-favored side of the upper limb to establish the models,while not receiving any treatment;subjects in the treatment group received both the same modeling and An-pressing manipulation treatment.The subjective rating of perceived exertion (RPE),subjective soreness sensation threshold and soreness grade were evaluated before modeling,immediately after modeling,and 24,48,72,96 and 120 h after modeling.Serum total antioxidant capacity (T-AOC) was measured before modeling,immediately after modeling,and 24,48 and 72 h after modeling.Serum creatine kinase MM isoenzyme (CK-MM) was measured before modeling and 24,48 and 72 h after modeling.Results:At 24,48,72 and 120 h after treatment,the soreness grades of the treatment group were lower than those of the model group (all P<0.05).The RPE scores of the treatment group were lower than those of the model group (all P<0.05) immediately after modeling,at 24,48,72,96 and 120 h after modeling.The subjective soreness sensation threshold of the treatment group was higher than that of the model group immediately after modeling,at 24,48,72 and 96 h after modeling (all P<0.05).Immediately after modeling,T-AOC value in the treatment group was higher than that in the model group and blank group (both P<0.05).CK-MM of the treatment group was lower than that of the model group at 48 h and 72 h after modeling (P<0.05).Conclusion:An-pressing manipulation shows a certain therapeutic effect on biceps brachii with DOMS by strengthening the body's antioxidant and anti-damage abilities,which can effectively reduce the pain and accelerate the recovery from fatigue damage.
摘要
Objective:To observe the influence of pressing force and time on the thermal effect of An-pressing manipulation.Methods:Eight healthy volunteers were recruited to receive An-pressing manipulation at Xinshu (BL 15) on the right side.The pressing force and time were both divided into five levels:the force described as extremely mild,mild,moderate,strong and extremely strong and time given by 2.5 min,5.0 min,7.5 min,10.0 min and 15.0 min.The real-time change in local acupoint temperature as well as the change during 1.0-15.0 min after the manipulation were observed.Results:Compared with the baseline data,the real-time changes in the temperature after An-pressing Xinshu (BL 15) on the right side with different levels of force (from mild to strong) were respectively (1.88t0.64) ℃,(2.05±0.68) ℃,(2.25±0.59) ℃,(2.35±0.61) ℃ and (2.32±0.69) ℃;the changes in 15.0 min after the manipulation were respectively (-0.11±0.11) ℃,(0.03±0.14) ℃,(0.59±0.58) ℃,(1.38±0.70) ℃ and (2.09±0.98) ℃.The real-time temperature changes after the manipulation for different durations (from short to long) were respectively (1.94±0.37) ℃,(2.33±0.29) ℃,(2.49±0.31) ℃,(2.51±0.39) ℃ and (2.41±0.55) ℃;the changes in 15.0 min after the manipulation were respectively (0.53±0.49) ℃,(0.33±0.30) ℃,(0.52±0.33) ℃,(0.55±0.38) ℃ and (0.76±0.36) ℃.Conclusion:The thermal effect presented an increasing tendency with the extension of pressing time,and the temperature reached the top at 7.5 min;the thermal effect showed an increasing tendency with the rise of pressing force,and the temperature reached the top upon a moderate level of force.The pressing time can produce a greater influence on the real-time temperature than the pressing force;the pressing force can produce a greater influence on maintaining the temperature than the pressing time.