摘要
Objective·To evaluate the effects of anterior maxillary segmental distraction osteogenesis(AMSDO)in treating sagittal maxillary hypoplasia in cleft lip and palate(CLP)patients and to report a 3D-printed surgical guide to facilitate the osteotomy.Methods·Twelve patients with CLP who underwent AMSDO were included in this study.Virtual osteotomy was performed in a 3-dimensional model and the osteotomy line were fabricated into a tooth-borne surgical guide by using 3D-printing technique.Lateral cephalograms taken before surgery(T0),at the end of consolidation(T1)and six months after consolidation(T2)were used to evaluate the effects of AMSDO.The accuracy of the osteotomy guide was measured by superimposing the postoperative CT data to virtual planning.Results·All the patients went through surgery without serious complications.SNA and overjet changed significantly both from T0 to T1 and from T0 to T2.ANB,facial convexity,and palatal length changed without significance from T0 to T1 and from T0 to T2.SNB remained stable.All the variables remained relatively stable from T1 to T2.The anteroposterior linear root-mean-square deviation(RMSD)between planning and actual results was 0.90 mm,while the angular RMSD in the sagittal plane was 5.07°.Conclusion·AMSDO is an effective treatment for maxillary hypoplasia secondary to CLP.The accuracy of this 3D-printed osteotomy guide is clinically acceptable,and this can simplify the surgery with fewer complications.
摘要
Objective:To investigate the status of the professional construction of head nurses in the tertiary hospitals of Shandong Province, and to master the professional cognition and attitude of the head nurses, and to provide reference for the formulation of the professional construction plan for the head nurses in the tertiary hospitals.Methods:A cross-sectional survey of 2 629 head nurses from 55 tertiary hospitals in Shandong Province was conducted using a self-designed questionnaire survey on the status of professional construction of head nurses in tertiary hospitals in Shandong Province.Results:The selection and training system of the head nurses in the tertiary hospitals in Shandong Province was mature. 93.00%(2 357/2 534) of the head nurses were undergraduate degrees, 18.40%(465/2 534) of the head nurses used all the working hours for nursing management, and 86.00%(2 179/2 534) were the main economic sources with the current position; 68.20%(1 728/2 534) were believed that the head nurse should be a trained nurse, 87.90%(2 227/2 534) thought that the head nurse′s professional construction was necessary, and the professional feasibility score was 77.93±19.75. The regression analysis showed that the factors affecting the head nurse′s own professional construction were age, satisfaction with salary satisfaction and self-worth ( P<0.05); 32.50%(257/791) of the head nurses suggested improving the management training system, 20.61%(163/791) recommended that the hospital should pay attention to the professional construction of the head nurse, and 7.33%(58/791) recommended establishing the standardization of professional standards. Conclusions:To improve the investment time of the head nurses and encourage the head nurses to continue the education management; the hospital should appropriately reduce the age requirements of the head nurses and improve the salary; establish a sound professional system and management training system for the head nurses, and comprehensively recommend the head nurses. Promote the professional development of the head nurse team
摘要
Objective To evaluate the effectiveness of computer aided design (CAD) and three bit printing in the management of orthognathic surgery.Methods A total of 5 cases of patients with jaw deformity were involved in this study;jaw teeth and CT scanning laser scanning hefore surgery,virtual surgery design of 3D reconstruction and fusion data were analyzed,according to the design scheme of double jaw surgery combined with genioplasty;design and 3D printing of maxillary Le Fort Ⅰ osteotomy,genioplasty titanium alloy resin osteotomy and positioning guide,sagittal split ramus osteotomy by 3D printing and plate technology were used in this approach.The postoperative results were compared with the surgical planning by three-dimensional measurement and statistical analysis.Results When the operation guide plate was applied smoothly,the maximum error for maxilla was 1.2 mm (0.3-1.2 mm),and the maximum error for genioplasty was 1.7 mm,(0.5-1.7 mm),and the mean error was less than 1 mm.Follow-up for 12 months showed no adverse reaction.Conclusions Three dimensional printing surgical guide plate can accurately provide the osteotomy information,effectively control the jaw movement,and improve the orthognathic surgery accuracy of patients with partial jaw deformity.
摘要
Objective@#To compare the surgical accuracy of the 3D printing surgical guide and traditional occlusal splint in the treatment of skeletal facial asymmetry cases.@*Methods@#12 facial asymmetric patients underwent joint orthognathic and orthodontics treatments were included in this research. In the 3D printing group (n=6) the pre-surgical CT scan for the skeleton and laser scan for the dentures were performed and 3D orthognathic procedures including Le FortⅠ and BSSRO combined with genioplasty were planned. The 3D printing surgical guides were manufactured and applied during surgeries. Another 6 cases were received same procedures by traditional occlusal splint techniques as the control group. Post-surgical CT reconstruction and 3D superimposition with pre-surgical planning was carried out for outcome comparison.@*Results@#The maximal error of maxillar was 0.65 mm and average error was less than 1 mm in 3D printing group, while the maxillary maximal error was 2.11 mm and average error was greater than 1 mm in traditional group which showed the statistical significance (P<0.05).@*Conclusions@#The usage of 3D printing surgical guide could improve the orthognathic surgical precision by controlling the jaw bone in a three-dimensional way.