Evaluation of a cross contamination model describing transfer of Salmonella spp. and Listeria monocytogenes during grinding of pork and beef.

In a previous study, a model was developed to describe the transfer and survival of Salmonella during grinding of pork (Møller, C.O.A., Nauta, M.J., Christensen, B.B., Dalgaard, P., Hansen, T.B., 2012. Modelling transfer of Salmonella typhimurium DT104 during simulation of grinding of pork. Journal of Applied Microbiology 112 (1), 90-98). The robustness of this model is now evaluated by studying its performance for predicting the transfer and survival of Salmonella spp. and Listeria monocytogenes during grinding of different types of meat (pork and beef), using two different grinders, different sizes and different numbers of pieces of meats to be ground. A total of 19 grinding trials were collected. Acceptable Simulation Zone (ASZ), visual inspection of the data, Quantitative Microbiological Risk Assessment (QMRA), as well as the Total Transfer Potential (TTP) were used as approaches to evaluate model performance and to access the quality of the cross contamination model predictions. Using the ASZ approach and considering that 70% of the observed counts have to be inside a defined acceptable zone of ±0.5 log10CFU per portion, it was found that the cross contamination parameters suggested by Møller et al. (2012) were not able to describe all 19 trials. However, for each of the collected grinding trials, the transfer event was well described when fitted to the model structure proposed by Møller et al. (2012). Parameter estimates obtained by fitting observed trials performed at different conditions, such as size and number of pieces of meat to be ground, may not be applied to describe cross contamination of unlike processing. Nevertheless, the risk estimates, as well as the TTP, revealed that the risk of disease may be reduced when the grinding of meat is performed in a grinder made of stainless steel (for all surfaces in contact with the meat), using a well-sharpened knife and holding at room temperatures lower than 4°C.

Spontaneous cocoa bean fermentation carried out in a novel-design stainless steel tank: influence on the dynamics of microbial populations and physical-chemical properties.

Spontaneous cocoa bean fermentations carried out in a novel-design 40-kg-capacity stainless steel tank (SST) was studied in parallel to traditional Brazilian methods of fermentation in wooden boxes (40-kg-capacity wooden boxes (WB1) and 600-kg-capacity wooden boxes (WB2)) using a multiphasic approach that entailed culture-dependent and -independent microbiological analyses of fermenting cocoa bean pulp samples and target metabolite analyses of both cocoa pulp and cotyledons. Both microbiological approaches revealed that the dominant species of major physiological roles were the same for fermentations in SST, relative to boxes. These species consisted of Saccharomyces cerevisiae and Hanseniaspora sp. in the yeast group; Lactobacillus fermentum and L. plantarum in the lactic acid bacteria (LAB) group; Acetobacter tropicalis belonging to the acetic acid bacteria (AAB) group; and Bacillus subtilis in the Bacillaceae family. A greater diversity of bacteria and non-Saccharomyces yeasts was observed in box fermentations. Additionally, a potentially novel AAB belonging to the genus Asaia was isolated during fermentation in WB1. Cluster analysis of the rRNA genes-PCR-DGGE profiles revealed a more complex picture of the box samples, indicating that bacterial and yeast ecology were fermentation-specific processes (wooden boxes vs. SST). The profile of carbohydrate consumption and fermentation products in the pulp and beans showed similar trends during both fermentation processes. However, the yeast-AAB-mediated conversion of carbohydrates into ethanol, and subsequent conversion of ethanol into acetic acid, was achieved with greater efficiency in SST, while temperatures were generally higher during fermentation in wooden boxes. With further refinements, the SST model may be useful in designing novel bioreactors for the optimisation of cocoa fermentation with starter cultures.

Reanimation of the lagophthalmos using stainless steel weight implantation; a new approach and prospective evaluation.

Weight implants have been used for over 30 years in surgical rehabilitation following lagophthalmos. However, there has been a renewed interest among ophthalmologists in recent years. The weight implant technique combined with lateral canthus resuspension was performed on 22 eyes in Thai patients. It is a reliable method for correcting lagophthalmos and ectropion. In previous studies almost pure gold was used in 99.99% of eyelid implants. However, we wanted to use other materials which are not expensive and are readily available. A stainless steel plate was selected. The majority of our surgeries were done with a stainless steel weight implant of 1.368 g. Patients were followed for 7 to 55 months, and no rejections of the implants were observed. This study achieved a > or = 90% success rate, and showed that a stainless steel plate is an alternative to gold for the weight implant technique.

Malignancy supervening on an intramedullary nail.

A primary, malignant, fibrous histiocytoma of bone occurring in association with a Hansen Street intramedullary nail occurred in a 39-year-old man. The physical and chemical characteristics of materials, in relation to the generation of secondary neoplasia are reviewed, but the problem of coincidence is difficult to exclude.