Calorimetry in Computed Tomography Beams.

A portable calorimeter for direct realization of absorbed dose in medical computed tomography (CT) procedures was constructed and tested in a positron emission tomography (PET) CT scanner. The calorimeter consists of two small thermistors embedded in a polystyrene (PS) cylindrical "core" (1.5 cm diameter) that can be inserted into a cylindrical high-density polyethylene (HDPE) phantom (30 cm diameter). The cylindrical design of core and phantom allows coaxial alignment of the system with the scanner rotation axis, which is necessary to minimize variations in dose that would otherwise occur as the X-ray source is rotated during scanning operations. The core can be replaced by a cylindrical ionization chamber for comparing dose measurement results. Measurements using the core and a calibrated thimble ionization chamber were carried out in a beam of 6 MV X-rays from a clinical accelerator and in 120 kV X-rays from a CT scanner. Doses obtained from the calorimeter and chamber in the 6 MV beam exhibited good agreement over a range of dose rates from 0.8 Gy/min to 4 Gy/min, with negligible excess heat. For the CT beam, as anticipated for these X-ray energies, the calorimeter response was complicated by excess heat from device components. Analyses done in the frequency domain and time domain indicated that excess heat increased calorimetric temperature rise by a factor of about 15. The calorimeter's response was dominated by dose to the thermistor, which contains high-atomic-number elements. Therefore, for future construction of calorimeters for CT beams, lower-atomic-number temperature sensors will be needed. These results serve as a guide for future alternative design of calorimeters toward a calorimetry absorbed dose standard for diagnostic CT.

Dosimetry characterization of a 32P source wire used for intravascular brachytherapy with automated stepping.

Depth-dose curve measurements and Monte Carlo simulations for a catheter-based 32P intravascular brachytherapy source wire are described. The measured dose rates were obtained using both radiochromic-dye film and an extrapolation chamber (EC). Calibrated radiochromic-dye films were irradiated at distances between 0.5 and 5 mm from the source axis in polystyrene phantoms, and scanned with high-resolution densitometers. Measurements with an automated EC with a 1 mm diameter collecting electrode were also performed at a distance of 2 mm from the source in polystyrene. The measured dose rates obtained from the film and EC were divided by the measured source activity to obtain measured values of dose rate per unit contained activity. Dosimetric calculations of the catheter-based 32P wire geometry were also obtained using several Monte Carlo codes (CYLTRAN, MCNP, PENELOPE, and EGS). The measured and calculated values of dose rate per unit contained activity are in good agreement (<10%) within the relevant treatment distances (1 to 4 mm). With carefully selected input parameters, the calculated depth-dose curves using these codes were within 5% at 4 mm depth. At greater depths the discrepancies between the codes increase. We discuss likely mechanisms for these differences.

Changes in the U.S. Primary Standards for the Air Kerma From Gamma-Ray Beams.

Monte Carlo photon-electron transport calculations have been done to derive new wall corrections for the six NBS-NIST standard graphite-wall, air-ionization cavity chambers that serve as the U.S. national primary standard for air kerma (and exposure) for gamma rays from (60)Co, (137)Cs, and (192)Ir sources. The data developed for and from these calculations have also been used to refine a number of other factors affecting the standards. The largest changes are due to the new wall corrections, and the total changes are +0.87 % to +1.11 % (depending on the chamber) for (60)Co beams, +0.64 % to +1.07 % (depending on the chamber) for (137)Cs beams, and -0.06 % for the single chamber used in the measurement of the standardized (192)Ir source. The primary standards for air kerma will be adjusted in the near future to reflect the changes in factors described in this work.