ABSTRACT
We report the design and operation of a surface-emitting surface acoustic wave (SAW) acousto-optical modulator which behaves as a cm-scale linear hologram in response to an applied electronic waveform. The modulator is formed by an optical waveguide, transducer, and out-coupling surface grating on a 1 mm-thick lithium niobate substrate. We demonstrate the ability to load and illuminate a 9-region linear hologram into the modulator's 8 mm-long interaction region using applied waveforms of 280-320 MHz. To the best of the authors' knowledge, this is the first demonstration of a monolithically-integrated, surface-emitting SAW modulator fabricated using lithographic techniques. Applications include practical implementations of a holographic display.
ABSTRACT
We report the design, fabrication, and characterization of ultralight highly emissive structures with a record-low mass per area that emit thermal radiation efficiently over a broad spectral (2 to 30 microns) and angular (0-60°) range. The structures comprise one to three pairs of alternating metallic and dielectric thin films and have measured effective 300 K hemispherical emissivity of 0.7 to 0.9 (inferred from angular measurements which cover a bandwidth corresponding to 88% of 300K blackbody power). To our knowledge, these micron-scale-thickness structures, are the lightest reported optical coatings with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these coatings are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation.
ABSTRACT
We report here several different superlattice photonic crystal based designs for 200nm thick c-Si solar cells, demonstrating that these structures have the ability to increase broadband absorption from λ = 300nm to 1100nm by more than 100% compared to a planar cell with an optimized anti-reflection coating. We show that adding superlattices into photonic crystals introduces new optical modes that contribute to enhanced absorption. The greatest improvements are obtained when combining a superlattice photonic crystal with a randomly textured dielectric coating that improves incoupling into the modes of the absorbing region. Finally, we show that our design methodology is also applicable to layers 1 to 4 microns in thickness, where absorbed currents competitive with conventional thick Si solar cells may be achieved.
ABSTRACT
In 1982, Yablonovitch proposed a thermodynamic limit on light trapping within homogeneous semiconductor slabs, which implied a minimum thickness needed to fully absorb the solar spectrum. However, this limit is valid for geometrical optics but not for a new generation of subwavelength solar absorbers such as ultrathin or inhomogeneously structured cells, wire-based cells, photonic crystal-based cells, and plasmonic cells. Here we show that the key to exceeding the conventional ray optic or so-called ergodic light trapping limit is in designing an elevated local density of optical states (LDOS) for the absorber. Moreover, for any semiconductor we show that it is always possible to exceed the ray optic light trapping limit and use these principles to design a number of new solar absorbers with the key feature of having an elevated LDOS within the absorbing region of the device, opening new avenues for solar cell design and cost reduction.
Subject(s)
Electric Power Supplies , Light , Models, Theoretical , Nanotechnology/instrumentation , Semiconductors , Solar Energy , Computer Simulation , Computer-Aided Design , Equipment Design , Equipment Failure Analysis , Scattering, RadiationABSTRACT
Silicon photonics is evolving from laboratory research to real-world applications with the potential to transform many technologies, including optical neural networks and quantum information processing. A key element for these applications is a reconfigurable switch operating at ultra-low programming energy-a challenging proposition for traditional thermo-optic or free carrier switches. Recent advances in non-volatile programmable silicon photonics based on phase-change materials (PCMs) provide an attractive solution to energy-efficient photonic switches with zero static power, but the programming energy density remains high (hundreds of attojoules per cubic nanometre). Here we demonstrate a non-volatile electrically reconfigurable silicon photonic platform leveraging a monolayer graphene heater with high energy efficiency and endurance. In particular, we show a broadband switch based on the technologically mature PCM Ge2Sb2Te5 and a phase shifter employing the emerging low-loss PCM Sb2Se3. The graphene-assisted photonic switches exhibited an endurance of over 1,000 cycles and a programming energy density of 8.7 ± 1.4 aJ nm-3, that is, within an order of magnitude of the PCM thermodynamic switching energy limit (~1.2 aJ nm-3) and at least a 20-fold reduction in switching energy compared with the state of the art. Our work shows that graphene is a reliable and energy-efficient heater compatible with dielectric platforms, including Si3N4, for technologically relevant non-volatile programmable silicon photonics.
ABSTRACT
The fabrication of a wafer-scale dislocation-free, fully relaxed single crystalline template for epitaxial growth is demonstrated. Transferring biaxially-strained Inx Ga1-x As ultrathin films from InP substrates to a handle support results in full strain relaxation and the Inx Ga1-x As unit cell assumes its bulk value. Our realization demonstrates the ability to control the lattice parameter and energy band structure of single layer crystalline compound semiconductors in an unprecedented way.