Transportation of mAb Dosing Solution in Intravenous Bag: Impact of Manual, Vehicle, and Pneumatic Tube System Transportation Methods on Product Quality.

Monoclonal antibody (mAb) products for intravenous (IV) administration generally require aseptic compounding with a commercial diluent within a pharmacy. The prepared dosing solution in the IV bag may be transported to the dosing location via manual, vehicular, pneumatic tube system (PTS), or a combination of these methods. In this study, the type and level of physical stresses associated with these three methods and their product quality impact for relatively sensitive and stable mAbs were assessed. Vibration was found to be the main stress associated with manual and vehicle transportation methods, although this was at a relatively low level (<1 GRMS/Root-Mean-Square Acceleration). Shock and drop events, at relatively low levels, were also observed with these methods. PTS transportation showed substantially more intense shock, vibration, and drop stresses and the measured levels were up to 91 G/force of acceleration or deceleration, 3.7 GRMS and 39 G, respectively. Using a foam padding insert for PTS transportation reduced the shock level considerably (91 G to 59 G). Transportation of mAb dosing solutions in IV bags via different methods including PTS transportation variables caused a small increase in the subvisible particle counts and there was no change in submicrometer particle distribution. No visible particles and no significant change to soluble aggregate levels were observed after transportation. Strategies such as removal of IV bag headspace prior to transport and in-line filtration poststress reduced the subvisible particles counts. All tested transportation conditions showed negligible impact on other product quality attributes tested. Removal of IV bag headspace prior to PTS transport prevented formation of micro air bubbles and foaming compared to the unaltered IV bag. This study shows examples where manual, vehicle, and PTS transport methods did not significantly impact product quality, and provides evidence that mAb products that are appropriately stabilized in the dosing solution (e.g., with a surfactant) can be transported via a PTS.

Industry Perspective on the use and Characterization of Polysorbates for Biopharmaceutical Products Part 1: Survey Report on Current State and Common Practices for Handling and Control of Polysorbates.

Polysorbates (PS) are widely used as a stabilizer in biopharmaceutical products. Industry practices on various aspects of PS are presented in this part 1 survey report based on a confidential survey and following discussions by 16 globally acting major biotechnology companies. The current practice and use of PS during manufacture across their global manufacturing sites are covered in addition to aspects like current understanding of the (in)stability of PS, the routine QC testing and control of PS, and selected regulatory aspects of PS. The results of the survey and extensive cross-company discussions are put into relation with currently available scientific literature. Part 2 of the survey report (upcoming) will focus on understanding, monitoring, prediction, and mitigation of PS degradation pathways to develop an effective control strategy.

An Intercompany Perspective on Compatibility and In-use Stability Studies to Enable Administration Of Biopharmaceutical Drug Products.

In-use stability and compatibility studies are often used in biotherapeutic development to assess stability and compatibility of biologic drugs with diluents and/or administration components at relevant conditions for the target route of administration (commonly intravenous, subcutaneous or intramuscular), to assure that patient safety and product efficacy are maintained during clinical use. To gain an understanding of current industry approaches for in-use stability and compatibility studies, the Formulation Workstream of the BioPhorum Development Group (BPDG), an industry-wide consortium, conducted an inter-company collaboration exercise, which included five bench-marking surveys around in-use stability and compatibility studies of biologic drugs. The results of this industry collaboration provide insights into the practicalities of these studies and how they are being used to support administration of biologics from early clinical programs to marketed products. The surveys queried topics including regulatory strategies and feedback; clinical in-use formulation, patient and site considerations; clinical blinding, masking and placebo approaches; study setup, execution and reporting; and clinical in-use stability and compatibility testing to provide a comprehensive picture of the range of common industry practices. This paper discusses the survey results and presents various approaches which can be used to guide the strategy and design of an in-use stability and compatibility program based on clinical and biomolecule needs.

Industry Perspective on the Use and Characterization of Polysorbates for Biopharmaceutical Products Part 2: Survey Report on Control Strategy Preparing for the Future.

Polysorbate (PS) 20 and 80 are the main surfactants used to stabilize biopharmaceutical products. Industry practices on various aspects of PS based on a confidential survey and following discussions by 16 globally acting major biotechnology companies is presented in two publications. Part 1 summarizes the current practice and use of PS during manufacture in addition to aspects like current understanding of the (in)stability of PS, the routine QC testing and control of PS, and selected regulatory aspects of PS.1 The current part 2 of the survey focusses on understanding, monitoring, prediction, and mitigation of PS degradation pathways in order to propose an effective control strategy. The results of the survey and extensive cross-company discussions are put into relation with currently available scientific literature.

An Intercompany Perspective on Biopharmaceutical Drug Product Robustness Studies.

The Biophorum Development Group (BPDG) is an industry-wide consortium enabling networking and sharing of best practices for the development of biopharmaceuticals. To gain a better understanding of current industry approaches for establishing biopharmaceutical drug product (DP) robustness, the BPDG-Formulation Point Share group conducted an intercompany collaboration exercise, which included a bench-marking survey and extensive group discussions around the scope, design, and execution of robustness studies. The results of this industry collaboration revealed several key common themes: (1) overall DP robustness is defined by both the formulation and the manufacturing process robustness; (2) robustness integrates the principles of quality by design (QbD); (3) DP robustness is an important factor in setting critical quality attribute control strategies and commercial specifications; (4) most companies employ robustness studies, along with prior knowledge, risk assessments, and statistics, to develop the DP design space; (5) studies are tailored to commercial development needs and the practices of each company. Three case studies further illustrate how a robustness study design for a biopharmaceutical DP balances experimental complexity, statistical power, scientific understanding, and risk assessment to provide the desired product and process knowledge. The BPDG-Formulation Point Share discusses identified industry challenges with regard to biopharmaceutical DP robustness and presents some recommendations for best practices.

Development of a stable low-dose aglycosylated antibody formulation to minimize protein loss during intravenous administration.

The physical and chemical integrity of a biopharmaceutical must be maintained not only during long-term storage but also during administration. Specifically for the intravenous (i.v.) delivery of a protein drug, loss of stability can occur when the protein formulation is compounded with i.v. bag diluents, thus modifying the original composition of the drug product. Here we present the challenges associated with the delivery of a low-dose, highly potent monoclonal antibody (mAb) via the i.v. route. Through parallel in-use stability studies and conventional formulation development, a drug product was developed in which adsorptive losses and critical oxidative degradation pathways were effectively controlled. This development approach enabled the i.v. administration of clinical doses in the range of 0.1 to 0.5 mg total protein, while ensuring liquid drug product storage stability under refrigerated conditions.