Au-Pd separation enhances bimetallic catalysis of alcohol oxidation.

In oxidation reactions catalysed by supported metal nanoparticles with oxygen as the terminal oxidant, the rate of the oxygen reduction can be a limiting factor. This is exemplified by the oxidative dehydrogenation of alcohols, an important class of reactions with modern commercial applications1-3. Supported gold nanoparticles are highly active for the dehydrogenation of the alcohol to an aldehyde4 but are less effective for oxygen reduction5,6. By contrast, supported palladium nanoparticles offer high efficacy for oxygen reduction5,6. This imbalance can be overcome by alloying gold with palladium, which gives enhanced activity to both reactions7,8,9; however, the electrochemical potential of the alloy is a compromise between that of the two metals, meaning that although the oxygen reduction can be improved in the alloy, the dehydrogenation activity is often limited. Here we show that by separating the gold and palladium components in bimetallic carbon-supported catalysts, we can almost double the reaction rate compared with that achieved with the corresponding alloy catalyst. We demonstrate this using physical mixtures of carbon-supported monometallic gold and palladium catalysts and a bimetallic catalyst comprising separated gold and palladium regions. Furthermore, we demonstrate electrochemically that this enhancement is attributable to the coupling of separate redox processes occurring at isolated gold and palladium sites. The discovery of this catalytic effect-a cooperative redox enhancement-offers an approach to the design of multicomponent heterogeneous catalysts.

N-Heterocyclic Carbene Modified Palladium Catalysts for the Direct Synthesis of Hydrogen Peroxide.

Heterogeneous palladium catalysts modified by N-heterocyclic carbenes (NHCs) are shown to be highly effective toward the direct synthesis of hydrogen peroxide (H2O2), in the absence of the promoters which are typically required to enhance both activity and selectivity. Catalytic evaluation in a batch regime demonstrated that through careful selection of the N-substituent of the NHC it is possible to greatly enhance catalytic performance when compared to the unmodified analogue and reach concentrations of H2O2 rivaling that obtained by state-of-the-art catalysts. The enhanced performance of the modified catalyst, which is retained upon reuse, is attributed to the ability of the NHC to electronically modify Pd speciation.

Bottom-up Synthesis of Water-Soluble Gold Nanoparticles Stabilized by N-Heterocyclic Carbenes: From Structural Characterization to Applications.

N-heterocyclic carbenes (NHCs) have become attractive ligands for functionalizing gold nanoparticle surfaces with applications ranging from catalysis to biomedicine. Despite their great potential, NHC stabilized gold colloids (NHC@AuNPs) are still scarcely explored and further efforts should be conducted to improve their design and functionalization. Here, the 'bottom-up' synthesis of two water-soluble gold nanoparticles (AuNP-1 and AuNP-2) stabilized by hydrophilic mono- and bidentate NHC ligands is reported together with their characterization by various spectroscopic and analytical methods. The NPs showed key differences likely to be due to the selected NHC ligand systems. Transmission electron microscopy (TEM) images showed small quasi-spherical and faceted NHC@AuNPs of similar particle size (ca. 2.3-2.6 nm) and narrow particle size distribution, but the colloids featured different ratios of Au(I)/Au(0) by X-ray photoelectron spectroscopy (XPS). Furthermore, the NHC@AuNPs were supported on titania and fully characterized. The new NPs were studied for their catalytic activity towards the reduction of nitrophenol substrates, the reduction of resazurin and for their photothermal efficiency. Initial results on their application in photothermal therapy (PTT) were obtained in human cancer cells in vitro. The aforementioned reactions represent important model reactions towards wastewater remediation, bioorthogonal transformations and cancer treatment.

Stable amorphous georgeite as a precursor to a high-activity catalyst.

Copper and zinc form an important group of hydroxycarbonate minerals that include zincian malachite, aurichalcite, rosasite and the exceptionally rare and unstable--and hence little known and largely ignored--georgeite. The first three of these minerals are widely used as catalyst precursors for the industrially important methanol-synthesis and low-temperature water-gas shift (LTS) reactions, with the choice of precursor phase strongly influencing the activity of the final catalyst. The preferred phase is usually zincian malachite. This is prepared by a co-precipitation method that involves the transient formation of georgeite; with few exceptions it uses sodium carbonate as the carbonate source, but this also introduces sodium ions--a potential catalyst poison. Here we show that supercritical antisolvent (SAS) precipitation using carbon dioxide (refs 13, 14), a process that exploits the high diffusion rates and solvation power of supercritical carbon dioxide to rapidly expand and supersaturate solutions, can be used to prepare copper/zinc hydroxycarbonate precursors with low sodium content. These include stable georgeite, which we find to be a precursor to highly active methanol-synthesis and superior LTS catalysts. Our findings highlight the value of advanced synthesis methods in accessing unusual mineral phases, and show that there is room for exploring improvements to established industrial catalysts.

Sulfur Promotion in Au/C Catalyzed Acetylene Hydrochlorination.

The formation of highly active and stable acetylene hydrochlorination catalysts is of great industrial importance. The successful replacement of the highly toxic mercuric chloride catalyst with gold has led to a flurry of research in this area. One key aspect, which led to the commercialization of the gold catalyst is the use of thiosulphate as a stabilizing ligand. This study investigates the use of a range of sulfur containing compounds as promoters for production of highly active Au/C catalysts. Promotion is observed across a range of metal sulfates, non-metal sulfates, and sulfuric acid treatments. This observed enhancement can be optimized by careful consideration of either pre- or post-treatments, concentration of dopants used, and modification of washing steps. Pre-treatment of the carbon support with sulfuric acid (0.76 m) resulted in the most active Au/C in this series with an acetylene conversion of ≈70% at 200 °C.

Revealing the electronic structure, heterojunction band offset and alignment of Cu2ZnGeSe4: a combined experimental and computational study towards photovoltaic applications.

Cu2ZnGeSe4 (CZGSe) is a promising earth-abundant and non-toxic semiconductor material for large-scale thin-film solar cell applications. Herein, we have employed a joint computational and experimental approach to characterize and assess the structural, optoelectronic, and heterojunction band offset and alignment properties of a CZGSe solar absorber. The CZGSe films were successfully prepared using DC-sputtering and e-beam evaporation systems and confirmed by XRD and Raman spectroscopy analyses. The CZGSe films exhibit a bandgap of 1.35 eV, as estimated from electrochemical cyclic voltammetry (CV) measurements and validated by first-principles density functional theory (DFT) calculations, which predicts a bandgap of 1.38 eV. A fabricated device based on the CZGSe as a light absorber and CdS as a buffer layer yields power conversion efficiency (PCE) of 4.4% with VOC of 0.69 V, FF of 37.15, and Jsc of 17.12 mA cm-2. Therefore, we suggest that interface and band offset engineering represent promising approaches to improve the performance of CZGSe devices by predicting a type-II staggered band alignment with a small conduction band offset of 0.18 eV at the CZGSe/CdS interface.

Selective catalytic oxidation using supported gold-platinum and palladium-platinum nanoalloys prepared by sol-immobilisation.

Supported nano-alloys have been prepared using the sol-immobilisation method for two bimetallic combinations, namely gold-platinum and palladium-platinum, using activated carbon and titania as supports. Some of the materials were prepared using a method where both metals are simultaneously reduced, thereby leading to homogeneous alloys being formed. In addition, sequential reduction of the metal combinations has also been investigated to facilitate the formation of core-shell structures. The materials have been characterized using X-ray photoelectron spectroscopy and aberration-corrected scanning transmission electron microscopy. The supported nanoparticles have been tested for a two selective oxidation reactions, namely the oxidation of toluene and benzyl alcohol using tertiary butyl hydroperoxide at 80 °C, in order to elucidate any potential structure-activity relationships.

Selective Oxidation of Methane to Methanol via In Situ H2O2 Synthesis.

The selective oxidation of methane to methanol, using H2O2 generated in situ from the elements, has been investigated using a series of ZSM-5-supported AuPd catalysts of varying elemental composition, prepared via a deposition precipitation protocol. The alloying of Pd with Au was found to offer significantly improved efficacy, compared to that observed over monometallic analogues. Complementary studies into catalytic performance toward the direct synthesis and subsequent degradation of H2O2, under idealized conditions, indicate that methane oxidation efficacy is not directly related to H2O2 production rates, and it is considered that the known ability of Au to promote the release of reactive oxygen species is the underlying cause for the improved performance of the bimetallic catalysts.

Highly efficient catalytic production of oximes from ketones using in situ-generated H2O2.

The ammoximation of cyclohexanone using preformed hydrogen peroxide (H2O2) is currently applied commercially to produce cyclohexanone oxime, an important feedstock in nylon-6 production. We demonstrate that by using supported gold-palladium (AuPd) alloyed nanoparticles in conjunction with a titanium silicate-1 (TS-1) catalyst, H2O2 can be generated in situ as needed, producing cyclohexanone oxime with >95% selectivity, comparable to the current industrial route. The ammoximation of several additional simple ketones is also demonstrated. Our approach eliminates the need to transport and store highly concentrated, stabilized H2O2, potentially achieving substantial environmental and economic savings. This approach could form the basis of an alternative route to numerous chemical transformations that are currently dependent on a combination of preformed H2O2 and TS-1, while allowing for considerable process intensification.

The Critical Role of ßPdZn Alloy in Pd/ZnO Catalysts for the Hydrogenation of Carbon Dioxide to Methanol.

The rise in atmospheric CO2 concentration and the concomitant rise in global surface temperature have prompted massive research effort in designing catalytic routes to utilize CO2 as a feedstock. Prime among these is the hydrogenation of CO2 to make methanol, which is a key commodity chemical intermediate, a hydrogen storage molecule, and a possible future fuel for transport sectors that cannot be electrified. Pd/ZnO has been identified as an effective candidate as a catalyst for this reaction, yet there has been no attempt to gain a fundamental understanding of how this catalyst works and more importantly to establish specific design criteria for CO2 hydrogenation catalysts. Here, we show that Pd/ZnO catalysts have the same metal particle composition, irrespective of the different synthesis procedures and types of ZnO used here. We demonstrate that all of these Pd/ZnO catalysts exhibit the same activity trend. In all cases, the ß-PdZn 1:1 alloy is produced and dictates the catalysis. This conclusion is further supported by the relationship between conversion and selectivity and their small variation with ZnO surface area in the range 6-80 m2g-1. Without alloying with Zn, Pd is a reverse water-gas shift catalyst and when supported on alumina and silica is much less active for CO2 conversion to methanol than on ZnO. Our approach is applicable to the discovery and design of improved catalysts for CO2 hydrogenation and will aid future catalyst discovery.

Gas Phase Glycerol Valorization over Ceria Nanostructures with Well-Defined Morphologies.

Glycerol solutions were vaporized and reacted over ceria catalysts with different morphologies to investigate the relationship of product distribution to the surface facets exposed, particularly, the yield of bio-renewable methanol. Ceria was prepared with cubic, rodlike, and polyhedral morphologies via hydrothermal synthesis by altering the concentration of the precipitating agent or synthesis temperature. Glycerol conversion was found to be low over the ceria with a cubic morphology, and this was ascribed to both a low surface area and relatively high acidity. Density functional theory calculations also showed that the (100) surface is likely to be hydroxylated under reaction conditions which could limit the availability of basic sites. Methanol space-time-yields over the polyhedral ceria samples were more than four times that for the cubic material at 400 °C, where 201 g of methanol was produced per hour per kilogram of the catalyst. Under comparable glycerol conversions, we show that the rodlike and polyhedral catalysts produce a major intermediate to methanol, hydroxyacetone (HA), with a selectivity of ca. 45%, but that over the cubic sample, this was found to be 15%. This equates to a 13-fold increase in the space-time-yield of HA over the polyhedral samples compared to the cubes at 320 °C. The implications of this difference are discussed with respect to the reaction mechanism, suggesting that a different mechanism dominates over the cubic catalysts to that for rodlike and polyhedral catalysts. The strong association between exposed surface facets of ceria to high methanol yields is an important consideration for future catalyst design in this area.

Uncovering the origin of enhanced field emission properties of rGO-MnO2 heterostructures: a synergistic experimental and computational investigation.

The unique structural merits of heterostructured nanomaterials including the electronic interaction, interfacial bonding and synergistic effects make them attractive for fabricating highly efficient optoelectronic devices. Herein, we report the synthesis of MnO2 nanorods and a rGO/MnO2 nano-heterostructure using low-cost hydrothermal and modified Hummers' methods, respectively. Detailed characterization and confirmation of the structural and morphological properties are done via X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM). Compared to the isolated MnO2 nanorods, the rGO/MnO2 nano-heterostructure exhibits impressive field emission (FE) performance in terms of the low turn-on field of 1.4 V µm-1 for an emission current density of 10 µA cm-2 and a high current density of 600 µA cm-2 at a relatively very low applied electric field of 3.1 V µm-1. The isolated MnO2 nanorods display a high turn-on field of 7.1 for an emission current density of 10 µA cm-2 and a low current density of 221 µA cm-2 at an applied field of 8.1 V µm-1. Besides the superior FE characteristics of the rGO/MnO2 nano-heterostructure, the emission current remains quite stable over the continuous 2 h period of measurement. The improvement of the FE characteristics of the rGO/MnO2 nano-heterostructure can be ascribed to the nanometric features and the lower work function (6.01 and 6.12 eV for the rGO with 8% and 16% oxygen content) compared to the isolated α-MnO2(100) surface (Φ = 7.22 eV) as predicted from complementary first-principles electronic structure calculations based on density functional theory (DFT) methods. These results suggest that an appropriate coupling of rGO with MnO2 nanorods would have a synergistic effect of lowering the electronic work function, resulting in a beneficial tuning of the FE characteristics.

Facile synthesis of precious-metal single-site catalysts using organic solvents.

Single-site catalysts can demonstrate high activity and selectivity in many catalytic reactions. The synthesis of these materials by impregnation from strongly oxidizing aqueous solutions or pH-controlled deposition often leads to low metal loadings or a range of metal species. Here, we demonstrate that simple impregnation of the metal precursors onto activated carbon from a low-boiling-point, low-polarity solvent, such as acetone, results in catalysts with an atomic dispersion of cationic metal species. We show the generality of this method by producing single-site Au, Pd, Ru and Pt catalysts supported on carbon in a facile manner. Single-site Au/C catalysts have previously been validated commercially to produce vinyl chloride, and here we show that this facile synthesis method can produce effective catalysts for acetylene hydrochlorination in the absence of the highly oxidizing acidic solvents previously used.

Metal Triflate-Promoted Allylic Substitution Reactions of Cinnamyl Alcohol in the Presence of Orthoesters and Acetals.

The product distribution of ethers formed from the reaction of cinnamyl alcohol with orthoesters in the presence of indium (III) triflate (InOTf)3 is dependent on both the reaction temperature and catalyst loading. Carrying out the reaction at room temperature under low loadings of the catalyst leads to a facile reaction generating the unexpected secondary allyl ether as the major product. In contrast, carrying out the reaction under higher catalyst loadings at elevated temperatures provides the expected primary linear ether in high yield and with excellent selectivity. The etherification reaction is also effective in the presence of acetals and ketals in place of orthoesters and allows for the development of the procedure to encompass a telescoped etherification protocol in which the acetal is generated in situ.

Nanocrystalline cobalt oxide: a catalyst for selective alkane oxidation under ambient conditions.

Nanocrystalline cobalt oxide activates propane, yielding propene at room temperature and pressure.

Visible-Light-Controlled Oxidation of Glucose using Titania-Supported Silver Photocatalysts.

The visible-light-mediated photo-catalytic selective valorisation of glucose using TiO2-supported Ag nanoparticles is shown for the first time. The optimisation of the catalyst composition, substrate-to-catalyst ratio and reaction medium proved that a near total suppression of the mineralisation pathway could be achieved with a selectivity to partial oxidation products and small-chain monosaccharides as high as 98 %. The primary products were determined to be gluconic acid, arabinose, erythrose, glyceraldehyde and formic acid. Under UVA light, the selectivity to organics decreases because of the production of CO2 from mineralisation. A reaction mechanism is proposed based on an α-scission process combined with the Ruff degradation reaction, which explains the presence of the oxidation products, the smaller carbohydrates and formic acid. X-ray photoelectron spectroscopy, UV/Vis spectroscopy and microscopy studies showed the presence of plasmonic 4 nm particles of silver that were oxidised to silver oxide over the course of the reaction, and recycling studies revealed that this was not detrimental to activity.

Base-free oxidation of glycerol using titania-supported trimetallic Au­Pd­Pt nanoparticles.

Base-free selective oxidation of glycerol has been investigated using trimetallic Au­Pd­Pt nanoparticles supported on titania and their corresponding bimetallic catalysts. Catalysts were prepared by the sol-immobilization method and characterized by means of TEM, UV/Vis spectroscopy, diffuse reflectance infrared fourier transform spectroscopy, X-ray photoelectron spectroscopy, and microwave plasma­atomic emission spectroscopy. It was found that of the bimetallic catalysts, Pd­Pt/TiO2 was the most active with high selectivity to C3 products. The addition of Au to this catalyst to form the trimetallic Au­Pd­Pt/TiO2, resulted in an increase in activity relative to Pd­Pt/TiO2. The turnover frequency increased from 210 h(−1) with the Pd­Pt/TiO2 catalyst to378 h(−1) for the trimetallic Au­Pd­Pt/TiO2 catalyst with retention of selectivity towards C3 products.

Deep oxidation of pollutants using gold deposited on a high surface area cobalt oxide prepared by a nanocasting route.

Gold deposited on a cobalt oxide with high surface area (138 m(2)g(-1)), obtained through a nanocasting route using a siliceous KIT-6 mesoporous material as a hard template, has demonstrated high activity for the total oxidation of propane and toluene, and ambient temperature CO oxidation. The addition of gold promotes the activity when compared to a gold-free Co(3)O(4) catalyst prepared using the same nanocasting technique. The enhanced catalytic activity when gold is present has been explained for the deep oxidation of propane and toluene in terms of the improved reducibility of cobalt oxide when gold is added, rather than to the intrinsic activity of metallic gold particles. The improved behaviour for CO oxidation has been linked to the simultaneous presence of Au(δ+) and Au°.