Engineering aspects of a mixed methanotrophic culture in a membrane-aerated biofilm reactor.

Methanotrophic biodegradation using the membrane-aerated biofilm reactor (MABR) is a technology offering several advantages over both conventional biofilm reactors and suspended-cell processes. In this study the oxidation efficiency of a methanotrophic biofilm in a 1.5 litre MABR was investigated. Measurements of oxygen and methane uptake rates together with biofilm thickness were taken for developing biofilms. It was found that the specific rate of metabolic activity of the biofilm was unusually high as determined by the methane and oxygen uptake rates. Microbial activity stratification was evident and the location of stratified layers of oxygen consuming components of the consortium could be manipulated via the intra-membrane oxygen pressure.

Biofilm development in a membrane-aerated biofilm reactor: effect of flow velocity on performance.

The effect of liquid flow velocity on biofilm development in a membrane-aerated biofilm reactor was investigated both by mathematical modeling and by experiment, using Vibrio natriegens as a test organism and acetate as carbon substrate. It was shown that velocity influenced mass transfer in the diffusion boundary layer, the biomass detachment rate from the biofilm, and the maximum biofilm thickness attained. Values of the overall mass transfer coefficient of a tracer through the diffusion boundary layer, the biofilm, and the membrane were shown to be identical during different experiments at the maximum biofilm thickness. Comparison of the results with published values of this parameter in membrane attached biofilms showed a similar trend. Therefore, it was postulated that this result might indicate the mechanism that determines the maximum biofilm thickness in membrane attached biofilms. In a series of experiments, where conditions were set so that the active layer of the membrane attached biofilm was located close to the membrane biofilm interface, it was shown that the most critical effect on process performance was the effect of velocity on biofilm structure. Biofilm thickness and effective diffusivity influenced reaction and diffusion in a complex manner such that the yield of biomass on acetate was highly variable. Consideration of endogenous respiration in the mathematical model was validated by direct experimental measurements of yield coefficients. Good agreement between experimental measurements of acetate and oxygen uptake rates and their prediction by the mathematical model was achieved.

Oxygen mass transfer characteristics in a membrane-aerated biofilm reactor.

Immobilization of pollutant-degrading microorganisms on oxygen-permeable membranes provides a novel method of increasing the oxidation capacity of wastewater treatment bioreactors. Oxygen mass transfer characteristics during continuous-flow steady-state experiments were investigated for biofilms supported on tubular silicone membranes. An analysis of oxygen mass transport and reaction using an established mathematical model for dual-substrate limitation supported the experimental results reported. In thick biofilms, an active layer of biomass where both carbon substrate and oxygen are available was found to exist. The location of this active layer varies depending on the ratio of the carbon substrate loading rate to the intramembrane oxygen pressure. The thickness of a carbon-substrate-starved layer was found to greatly influence the mass transport of oxygen into the active biomass layer, which was located close to, but not in contact with, the biofilm-liquid interface. The experimental results demonstrated that oxygen uptake rates as high as 20 g m-2 d-1 bar-1 can be achieved, and the model predicts that, for an optimized biofilm thickness, oxygen uptake rates of more than 30 g m-2 d-1 bar-1 should be possible. This would allow membrane-aerated biofilm reactors to operate with much greater thicknesses of active biomass than can conventional biofilm reactors as well as offering the further advantage of close to 100% oxygen conversion efficiencies for the treatment of high-strength wastewaters. In the case of dual- substrate-limited biofilms, the potential to increase the oxygen flux does not necessarily increase the substrate (acetate) removal rate.

Trials and tribulations in deploying digital imaging network and picture archiving and communication system--film to filmless in 80 days.

The Naval Medical Center Portsmouth (NMCP) was constructed with the intention of deploying a picture archiving and communications system (PACS). All necessary infrastructures were installed and considerable planning was done during construction with the belief that this would make the deployment of the PACS much simpler. This was true during the early deployment; however, as time passed and the system was more heavily used, significant problems arose. User/operator-related and hardware/software-related problems were encountered. Although, most have been corrected, some have persisted and will require considerable manpower and/or fiscal resources to correct. The lesson learned is that no matter how much preparation is done for deploying PACS, many significant problems will surface as the system is used that will require the continued attention of the deployment project officer.

Quality-control issues on high-resolution diagnostic monitors.

Previous literature indicates a need for more data collection in the area of quality control of high-resolution diagnostic monitors. Throughout acceptance testing, which began in June 2000, stability of monitor calibration was analyzed. Although image quality on all monitors was found to be acceptable upon initial acceptance testing using VeriLUM software by Image Smiths, Inc (Germantown, MD), it was determined to be unacceptable during the clinical phase of acceptance testing. High-resolution monitors were evaluated for quality assurance on a weekly basis from installation through acceptance testing and beyond. During clinical utilization determination (CUD), monitor calibration was identified as a problem and the manufacturer returned and recalibrated all workstations. From that time through final acceptance testing, high-resolution monitor calibration and monitor failure rate remained a problem. The monitor vendor then returned to the site to address these areas. Monitor defocus was still noticeable and calibration checks were increased to three times per week. White and black level drift on medium-resolution monitors had been attributed to raster size settings. Measurements of white and black level at several different size settings were taken to determine the effect of size on white and black level settings. Black level remained steady with size change. White level appeared to increase by 2.0 cd/m2 for every 0.1 inches decrease in horizontal raster size. This was determined not to be the cause of the observed brightness drift. Frequency of calibration/testing is an issue in a clinical environment. The increased frequency required at our site cannot be sustained. The medical physics division cannot provide dedicated personnel to conduct the quality-assurance testing on all monitors at this interval due to other physics commitments throughout the hospital. Monitor access is also an issue due to radiologists' need to read images. Some workstations are in use 7 AM to 11 PM daily. An appropriate monitor calibration frequency must be established during acceptance testing to ensure unacceptable drift is not masked by excessive calibration frequency. Standards for acceptable black level and white level drift also need to be determined. The monitor vendor and hospital staff agree that currently, very small printed text is an acceptable method of determining monitor blur, however, a better method of determining monitor blur is being pursued. Although monitors may show acceptable quality during initial acceptance testing, they need to show sustained quality during the clinical acceptance-testing phase. Defocus, black level, and white level are image quality concerns, which need to be evaluated during the clinical phase of acceptance testing. Image quality deficiencies can have a negative impact on patient care and raise serious medical-legal concerns. The attention to quality control required of the hospital staff needs to be realistic and not have a significant impact on radiology workflow.