Hybrid Nanogenerators for Ocean Energy Harvesting: Mechanisms, Designs, and Applications.

The ocean holds vast potential as a renewable energy source, but harnessing its power has been challenging due to low-frequency and high-amplitude stimulation. However, hybrid nanogenerators (HNGs) offer a promising solution to convert ocean energy into usable power efficiently. With their high sensitivity and flexible design, HNGs are ideal for low-frequency environments and remote ocean regions. Combining triboelectric nanogenerators (TENGs) with piezoelectric nanogenerators (PENGs) and electromagnetic nanogenerators (EMGs) creates a unique hybrid system that maximizes energy harvesting. Ultimately, hybrid energy-harvesting systems offer a sustainable and reliable solution for growing energy needs. This study provides an in-depth review of the latest research on ocean energy harvesting by hybrid systems, focusing on self-powered applications. The article also discusses primary hybrid designs for devices, powering self-powered units such as wireless communication systems, climate monitoring systems, and buoys as applications. The potential of HNGs is enormous, and with rapid advancements in research and fabrication, these systems are poised to revolutionize ocean energy harvesting. It outlines the pros and cons of HNGs and highlights the major challenges that must be overcome. Finally, future outlooks for hybrid energy harvesters are also discussed.

Nanocrystalline Antiferromagnetic High-κ Dielectric Sr2NiMO6 (M = Te, W) with Double Perovskite Structure Type.

Double perovskites have been extensively studied in materials chemistry due to their excellent properties and novel features attributed to the coexistence of ferro/ferri/antiferro-magnetic ground state and semiconductor band gap within the same material. Double perovskites with Sr2NiMO6 (M = Te, W) structure type have been synthesized using simple, non-toxic and costless aqueous citrate sol-gel route. The reaction yielded phase-pure nanocrystalline powders of two compounds: Sr2NiWO6 (SNWO) and Sr2NiTeO6 (SNTO). According to the Rietveld refinement of powder X-ray diffraction data at room temperature, Sr2NiWO6 is tetragonal (I4/m) and Sr2NiTeO6 is monoclinic (C12/m1), with average crystallite sizes of 49 and 77 nm, respectively. Structural studies have been additionally performed by Raman spectroscopy revealing optical phonons typical for vibrations of Te6+/W6+O6 octahedra. Both SNTO and SNWO possess high values of dielectric constants (341 and 308, respectively) with low dielectric loss (0.06 for SNWO) at a frequency of 1 kHz. These values decrease exponentially with the increase of frequency to 1000 kHz, with the dielectric constant being around 260 for both compounds and dielectric loss being 0.01 for SNWO and 0.04 for SNTO. The Nyquist plot for both samples confirms the non-Debye type of relaxation behavior and the dominance of shorter-range movement of charge carriers. Magnetic studies of both compounds revealed antiferromagnetic behavior, with Néel temperature (TN) being 57 K for SNWO and 35 K for SNTO.

Effect of synthesis methodologies upon the photocatalytic performance of Bi0.5Na0.5TiO3 for pollutant degradation.

In the face of mounting environmental concerns, we must seek out innovative solutions for remediation. Using nanomaterials to degrade organic pollutants in water under ambient visible light holds great promise as a safe, cost-efficient, and effective approach to addressing pollution in our water bodies. The development of novel materials capable of such pollution degradation is desired to preserve the environment. In this study, Bi0.5Na0.5TiO3 (BNT) nanoparticles are synthesized through hydrothermal and solid-state routes, and their physicochemical properties are compared to assess their photocatalytic performance. The results of the characterization studies indicate that the hydrothermally synthesized nanoparticles outperformed the solid-state synthesized counterparts in terms of photocatalytic performance. The photocatalytic degradation of Rhodamine blue dye under ambient light exposure is examined at various dye concentrations and catalyst dosages. BNT nanoparticles demonstrated excellent photocatalytic properties, stability, and recyclability, making them a promising candidate for various photocatalytic applications. The findings of this study could pave the way for the development of sustainable and environmentally friendly photocatalytic technologies for water remediation.

3D printed triboelectric nanogenerator for underwater ultrasonic sensing.

The underwater ultrasound power measurement has become necessary due to the rapid development of sonochemistry and sonocatalysis. This article presents construction of novel triboelectric nanogenerator (TENG) and its application for a detection of ultrasonic waves in water. The device was 3D printed using widely available and cost-effective materials. TENG consisted of the device housing and movable polymer pellets confined between flat electrodes. The device housing and pellets were 3D printed via stereolithography (SLA) and fused deposition modelling (FDM) methods, respectively. The pellets moved periodically driven by the ultrasonic waves leading to generation of an alternating voltage signal. The electric response of TENG was calibrated using a commercially available ultrasonic power sensor. The open-circuit voltage output of TENG was registered in different sections of the ultrasonic bath in order to determine the distribution of the acoustic power. TENG electric responses were analyzed by applying the fast Fourier transform (FFT) and fitting the theoretical dependence to experimental data. The main peaks in the frequency spectra of the voltage waveforms corresponded to the fundamental excitation frequency of the ultrasonic bath. TENG device, presented in this paper, can be successfully applied as a self-powered sensor for detection of ultrasonic waves. It enables precise control of the sonochemical process and reduction of power losses of the ultrasonic reactor. 3D printing technology has been confirmed to be fast, easy, and scalable method of fabrication of the ultrasonic sensors.

Sustainable Solutions for Oral Health Monitoring: Biowaste-Derived Triboelectric Nanogenerator.

Oral healthcare monitoring is a vital aspect of identifying and addressing oral dental problems including tooth decay, gum pain, and oral cancer. Day by day, healthcare facilities and regular checkups are becoming more costly and time-consuming. In this context, consumers are moving toward advanced technology, such as bite sensors, to obtain regular data about their occlusal chewing patterns and strength. The triboelectric nanogenerator (TENG) can potentially eliminate the need for a battery by simply converting abundant vibrations from nature or human motion into electrical energy. In this work, biomaterials are obtained from biowastes such as cellulose from wood waste, chitosan from crab shells, and gelatin from fish scales. All wastes are biodegradable, and our work aims at sustainability and waste hierarchy. The single electrode mode-based TENG was designed and fabricated using biodegradable poly(vinyl alcohol) (PVA)-biomaterial composites, rice paper as a substrate, and edible silver leaf as an electrode. The highest electrical output was obtained for PVA/chitosan 10 wt % composite-based TENG (PC10) of about 20 V, 200 nA, and 12 nC. The biomechanical energy harvesting was measured, and powering of LED was demonstrated using a PC10 TENG device. A biocompatible bite sensor based on the TENG was used to measure the biting force of a dummy teeth model to demonstrate its potential use in dental health applications. It indicates the promising future value of disposable oral medication devices without any invasive surgery or injection.

Bismuth sulfoiodide (BiSI) nanorods: synthesis, characterization, and photodetector application.

The nanorods of bismuth sulfoiodide (BiSI) were synthesized at relatively low temperature (393 K) through a wet chemical method. The crystalline one-dimensional (1D) structure of the BiSI nanorods was confirmed using high resolution transmission microscopy (HRTEM). The morphology and chemical composition of the material were examined by applying scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS), respectively. The average diameter of 126(3) nm and length of 1.9(1) µm of the BiSI nanorods were determined. X-ray diffraction (XRD) revealed that prepared material consists of a major orthorhombic BiSI phase (87%) and a minor amount of hexagonal Bi13S18I2 phase (13%) with no presence of other residual phases. The direct energy band gap of 1.67(1)  eV was determined for BiSI film using diffuse reflectance spectroscopy (DRS). Two types of photodetectors were constructed from BiSI nanorods. The first one was traditional photoconductive device based on BiSI film on stiff glass substrate equipped with Au electrodes. An influence of light intensity on photocurrent response to monochromatic light (λ = 488 nm) illumination was studied at a constant bias voltage. The novel flexible photo-chargeable device was the second type of prepared photodetectors. It consisted of BiSI film and gel electrolyte layer sandwiched between polyethylene terephthalate (PET) substrates coated with indium tin oxide (ITO) electrodes. The flexible self-powered BiSI photodetector exhibited open-circuit photovoltage of 68 mV and short-circuit photocurrent density of 0.11 nA/cm2 under light illumination with intensity of 0.127 W/cm2. These results confirmed high potential of BiSI nanorods for use in self-powered photodetectors and photo-chargeable capacitors.

Carbohydrate-protein interaction-based detection of pathogenic bacteria using a biodegradable self-powered biosensor.

Battery-free and biodegradable sensors can detect biological elements in remote areas. The triboelectric nanogenerator (TENG) can potentially eliminate the need for a battery by simply converting the abundant vibrations from nature or human motion into electricity. A biodegradable sensor system integrated with TENG to detect commonly found disease-causing bacteria (E. coli) in the environment is showcased herein. In this system, D-mannose functionalized 3D printed polylactic acid (PLA) with the brush-painted silver electrode was used to detect E. coli by a simple carbohydrate-protein interaction mechanism. The adsorption capacity of D-mannose is generally altered by varying the concentration of E. coli resulting in changes in resistance. Thus, the presented biosensor can detect bacterial concentrations by monitoring the output current. The PLA TENG generates an output of 70 V, 800 nA, and 22 nC, respectively. In addition, tap water and unpasteurized milk samples are tested for detecting bacteria, and the output is measured at 6 µA and 5 µA, respectively. Further, the biosensor was tested for biodegradability in soil compost by maintaining constant temperature and humidity. This study not only proposes an efficient and fast method for screening E. coli but also gives important insights into the ability to degrade and long-term reliability of TENG-based sensor platforms.

A focused review on three-dimensional bioprinting technology for artificial organ fabrication.

Three-dimensional (3D) bioprinting technology has attracted a great deal of interest because it can be easily adapted to many industries and research sectors, such as biomedical, manufacturing, education, and engineering. Specifically, 3D bioprinting has provided significant advances in the medical industry, since such technology has led to significant breakthroughs in the synthesis of biomaterials, cells, and accompanying elements to produce composite living tissues. 3D bioprinting technology could lead to the immense capability of replacing damaged or injured tissues or organs with newly dispensed cell biomaterials and functional tissues. Several types of bioprinting technology and different bio-inks can be used to replicate cells and generate supporting units as complex 3D living tissues. Bioprinting techniques have undergone great advancements in the field of regenerative medicine to provide 3D printed models for numerous artificial organs and transplantable tissues. This review paper aims to provide an overview of 3D-bioprinting technologies by elucidating the current advancements, recent progress, opportunities, and applications in this field. It highlights the most recent advancements in 3D-bioprinting technology, particularly in the area of artificial organ development and cancer research. Additionally, the paper speculates on the future progress in 3D-bioprinting as a versatile foundation for several biomedical applications.

Nanogenerator for determination of acoustic power in ultrasonic reactors.

This paper presents the novel use of a sonochemical reaction product as a sensing material in self-powered ultrasonic reactor devices for determination of ultrasound parameters. A piezoelectric nanogenerator was fabricated via sonochemical synthesis of SbSeI nanowires compressed into a bulk sample. The prepared device was used to develop two fast and simple evaluation methods for acoustic power in liquid. A calibration procedure was carried out for both methods using a VCX-750 ultrasonic processor. The ultrasound acoustic power was varied within a 150 W to 750 W range and the corresponding nanogenerator electrical responses were measured. The voltage signals of the first method fit the best with theoretical dependence. The second technique was based on the application of the Fast Fourier Transform (FFT) to the measured electric output. The results of these two approaches were convergent. Acoustic power values of 255(8) W and 222(7) W were determined for the Sonic-6 reactor using theoretical dependence fitting to experimental data and FFT analysis, respectively. Developed sensing technology possesses great potential for sonochemistry applications.

Preparation of Multifunctional N-Doped Carbon Quantum Dots from Citrus clementina Peel: Investigating Targeted Pharmacological Activities and the Potential Application for Fe3+ Sensing.

Carbon quantum dots (CQDs) have recently emerged as innovative theranostic nanomaterials, enabling fast and effective diagnosis and treatment. In this study, a facile hydrothermal approach for N-doped biomass-derived CQDs preparation from Citrus clementina peel and amino acids glycine (Gly) and arginine (Arg) has been presented. The gradual increase in the N-dopant (amino acids) nitrogen content increased the quantum yield of synthesized CQDs. The prepared CQDs exhibited good biocompatibility, stability in aqueous, and high ionic strength media, similar optical properties, while differences were observed regarding the structural and chemical diversity, and biological and antioxidant activity. The antiproliferative effect of CQD@Gly against pancreatic cancer cell lines (CFPAC-1) was observed. At the same time, CQD@Arg has demonstrated the highest quantum yield and antioxidant activity by DPPH scavenging radical method of 81.39 ± 0.39% and has been further used for the ion sensing and cellular imaging of cancer cells. The obtained results have demonstrated selective response toward Fe3+ detection, with linear response ranging from 7.0 µmol dm-3 to 50.0 µmol dm-3 with R2 = 0.9931 and limit of detection (LOD) of 4.57 ± 0.27 µmol dm-3. This research could be a good example of sustainable biomass waste utilization with potential for biomedical analysis and ion sensing applications.

Dielectric, conductivity and ferroelectric properties of lead-free electronic ceramic:0.6Bi(Fe0.98Ga0.02)O3-0.4BaTiO3.

This paper presents the fabrication of a polycrystalline sample of the above electronic system by a mixed-oxide technique. The X-ray diffraction pattern show the evolution of perovskite phase (including some impurity phase). The rhombohedral symmetry and crystallite size of 42 nm were also found from the XRD. The distribution of grains in the microstructure suggests the formation of high density ceramics. The role of grains, grain boundaries and interface on resistive (impedance, electrical modulus and electrical transport) and insulating (dielectric) has been investigated over a wide range of frequencies (103-106 Hz) and temperatures (25-400 °C) using spectroscopy (dielectric, modulus and impedance) techniques. The Nyquist plot illustrates the presence of effects such as grain and grain boundary over selected temperatures. Analysis of conductivity spectra reveals that the electrical transport process of the material is influenced by charge transfer by hopping. The complex modulus spectrum also describes the dielectric relaxation of the material. The study of field dependent polarization reveals the existence of ferroelectricity in the material.