TiO2 and Nitrogen Doped TiO2 Prepared by Different Methods; on the (Micro)structure and Photocatalytic Activity in CO2 Reduction and N2O Decomposition.

TiO2 as nanostructured powders were prepared by (1) sol-gel process and (2) hydrothermal method in combination with (A) the processing by pressurized hot water and methanol or (B) calcination. The subsequent synthesis step was the modification of prepared nanostructured TiO2 with nitrogen using commercial urea. Textural, structural, surface and optical properties of prepared TiO2 and N/TiO2 were characterized by nitrogen physisorption, powder X-ray diffraction, X-ray photoelectron spectroscopy and DR UV-vis spectroscopy. It was revealed that TiO2 and N/TiO2 processed by pressurized fluids showed the highest surface areas. Furthermore, all prepared materials were the mixtures of major anatase phase and minor brookite phase, which was in nanocrystalline or amorphous (as nuclei) form depending on the applied preparation method. All the N/TiO2 materials exhibited enhanced crystallinity with a larger anatase crystallite-size than undoped parent TiO2. The photocatalytic activity of the prepared TiO2 and N/TiO2 was tested in the photocatalytic reduction of CO2 and the photocatalytic decomposition of N2O. The key parameters influencing the photocatalytic activity was the ratio of anatase-to-brookite and character of brookite. The optimum ratio of anatase-to-brookite for the CO2 photocatalytic reduction was determined to be about 83 wt.% of anatase and 17 wt.% of brookite (amorphous-like) (TiO2-SG-C). The presence of nitrogen decreased a bit the photocatalytic activity of tested materials. On the other hand, TiO2-SG-C was the least active in the N2O photocatalytic decomposition. In the case of N2O photocatalytic decomposition, the modification of TiO2 crystallites surface by nitrogen increased the photocatalytic activity of all investigated materials. The maximum N2O conversion (about 63 % after 18 h of illumination) in inert gas was reached over all N/TiO2.

Novel TiO2/C3N4 Photocatalysts for Photocatalytic Reduction of CO2 and for Photocatalytic Decomposition of N2O.

TiO2/g-C3N4 photocatalysts with the ratio of TiO2 to g-C3N4 ranging from 0.3/1 to 2/1 were prepared by simple mechanical mixing of pure g-C3N4 and commercial TiO2 Evonik P25. All the nanocomposites were characterized by X-ray powder diffraction, UV-vis diffuse reflectance spectroscopy, photoluminescence, X-ray photoelectron spectroscopy, Raman spectroscopy, infrared spectroscopy, transmission electron microscopy, photoelectrochemical measurements, and nitrogen physisorption. The prepared mixtures along with pure TiO2 and g-C3N4 were tested for the photocatalytic reduction of carbon dioxide and photocatalytic decomposition of nitrous oxide. The pure g-C3N4 exhibited the lowest photocatalytic activity in both cases, pointing to a very high recombination rate of charge carriers. On the other hand, the most active photocatalyst toward all the products was (0.3/1)TiO2/g-C3N4. The highest activity is achieved by combination of a number of factors: (i) specific surface area, (ii) adsorption edge energy, (iii) crystallite size, and (iv) efficient separation of the charge carriers, where the efficient charge separation is the most decisive parameter.

Microstructure, Optical and Photocatalytic Properties of TiO2 Thin Films Prepared by Chelating-Agent Assisted Sol-Gel Method.

Single and multilayer TiO2 thin films coated on two types of soda-lime glass substrates (microscope slides and cylinders) were prepared by a chelating agent-assisted sol-gel method, using ethyl acetoacetate as a chelating agent, dip-coating and calcination at 500 °C for 2 h in air. Phase composition, microstructural, morphological and optical properties of thin films were comprehensively investigated by using XRF, advanced XRD analysis, Raman and UV-vis spectroscopy and AFM. It was found out that the thickness of thin films increases linearly with increasing number of deposited layers, indicating a good adhesion of the titania solution to a glass substrate as well as to a previously calcined layer. 1 layer film crystallized to anatase-TiO2(B) mixture with minor/negligible amount of nanosized brookite, 2-4 layers films crystallized to anatase-brookite-TiO2(B) mixture. In contrast to other multilayers films, 4 layers film was highly inhomogeneous. The different phase composition of thin films was clarified based on the crystallization via titanate/s and metastable monoclinic TiO2(B) as a consequence of several phenomena; the diffusion of Na⁺ ions from a soda-lime glass substrate, acidic conditions and repeated thermal treatment. The multilayer films were in average highly transparent (80-95%) in the visible light region with the sharp absorption edge in the UV light region. Additionally, the photocatalytic properties of selected multilayer films were compared in AO7 photodegradation. Photocatalytic experiments showed that thicker 4 layers film of tricrystalline anatase-brookite-TiO2(B) phase mixture was similarly active as thinner 3 layers film of similar phase composition, which may be a consequence of the inhomogeneity of the thicker film.

Photocatalytic decomposition of methanol over La/TiO2 materials.

Lanthanum-modified TiO2 photocatalysts (0.2-1.5 wt% La) were investigated in the methanol decomposition in an aqueous solution. The photocatalysts were prepared by the common sol-gel method followed by calcination. The structural (X-ray diffraction, Raman, X-ray photoelectron spectroscopy), textural (N2 physisorption), and optical properties (diffuse reflectance spectroscopy, photoelectrochemical measurements) of all synthetized nanomaterials were correlated with photocatalytic activity. Both pure TiO2 and La-doped TiO2 photocatalysts proved higher yields of hydrogen in comparison to photolysis. The photocatalyst with optimal amount of lanthanum (0.2 wt% La) showed almost two times higher amount of hydrogen produced at the same time as in the presence of pure TiO2. The photocatalytic activity increased with both increasing photocurrent response and decreasing amount of lattice and surface O species. It has been shown that both direct and indirect mechanisms of methanol photocatalytic oxidation participate in the production of hydrogen. Both direct and indirect mechanisms take part in the formation of hydrogen.

Nanostructured composite material graphite/TiO2 and its antibacterial activity under visible light irradiation.

The paper addresses laboratory preparation, characterization and in vitro evaluation of antibacterial activity of graphite/TiO2 nanocomposites. Composites graphite/TiO2 with various ratio of TiO2 nanoparticles (30wt.%, and 50wt.%) to graphite were prepared using a thermal hydrolysis of titanylsulfate in the presence of graphite particles, and subsequently dried at 80°C. X-ray powder diffraction, transmission electron microscopy and Raman microspectroscopy served as phase-analytical methods distinguishing anatase and rutile phases in the prepared composites. Scanning and transmission electron microscopy techniques were used for characterization of morphology of the prepared samples. A developed modification of the standard microdilution test was used for in vitro evaluation of daylight induced antibacterial activity, using four common human pathogenic bacterial strains (Staphylococcus aureus, Escherichia coli, Enterococcus faecalis and Pseudomonas aeruginosa). Antibacterial activity of the graphite/TiO2 nanocomposites could be based mainly on photocatalytic reaction with subsequent potential interaction of reactive oxygen species with bacterial cells. During the antibacterial activity experiments, the graphite/TiO2 nanocomposites exhibited antibacterial activity, where differences in the onset of activity and activity against bacterial strains were observed. The highest antibacterial activity evaluated as minimum inhibitory concentration was observed against P. aeruginosa after 180min of irradiation.

Antibacterial activity of kaolinite/nanoTiO2 composites in relation to irradiation time.

The paper addresses laboratory preparation and antibacterial activity testing of kaolinite/nanoTiO2 composite in respect of the daylight irradiation time. Kaolinite/nanoTiO2 composites with 20 and 40 wt% of TiO2 were laboratory prepared, dried at 105 °C and calcined at 600 °C. The calcination caused transformation of kaolinite to metakaolinite and origination of the metakaolinite/nanoTiO2 composite. X-ray powder diffraction, Raman and FTIR spectroscopic methods revealed titanium dioxide only in the form of anatase in all evaluated samples (non-calcined and calcined) and also transformation of kaolinite to metakaolinite after the calcination treatment. Scanning electron microscopy was used as a method for characterization of morphology and elemental composition of the studied samples. A standard microdilution test was used to determine the antibacterial activity using four human pathogenic bacterial strains (Staphylococcus aureus, Escherichia coli, Enterococcus faecalis, Pseudomonas aeruginosa). A lamp with a wide spectrum bulb simulating daylight was used for induction of photocatalysis. The antibacterial assays found all the KATI samples to have antibacterial potency with different onset of the activity when calcined samples exhibited antibacterial activity earlier than the non-calcined. Significant difference in antibacterial activity of KATI samples for different bacterial strains was not observed.