An Angle on MK2 Inhibition-Optimization and Evaluation of Prevention of Activation Inhibitors.

The mitogen-activated protein kinase p38α pathway has been an attractive target for the treatment of inflammatory conditions such as rheumatoid arthritis. While a number of p38α inhibitors have been taken to the clinic, they have been limited by their efficacy and toxicological profile. A lead identification program was initiated to selectively target prevention of activation (PoA) of mitogen-activated protein kinase-activated protein kinase 2 (MK2) rather than mitogen- and stress-activated protein kinase 1 (MSK1), both immediate downstream substrates of p38α, to improve the efficacy/safety profile over direct p38α inhibition. Starting with a series of pyrazole amide PoA MK2 inhibitor leads, and guided by structural chemistry and rational design, a highly selective imidazole 9 (2-(3'-(2-amino-2-oxoethyl)-[1,1'-biphenyl]-3-yl)-N-(5-(N,N-dimethylsulfamoyl)-2-methylphenyl)-1-propyl-1H-imidazole-5-carboxamide) and the orally bioavailable imidazole 18 (3-methyl-N-(2-methyl-5-sulfamoylphenyl)-2-(o-tolyl)imidazole-4-carboxamide) were discovered. The PoA concept was further evaluated by protein immunoblotting, which showed that the optimized PoA MK2 compounds, despite their biochemical selectivity against MSK1 phosphorylation, behaved similarly to p38 inhibitors in cellular signaling. This study highlights the importance of selective tool compounds in untangling complex signaling pathways, and although 9 and 18 were not differentiated from p38α inhibitors in a cellular context, they are still useful tools for further research directed to understand the role of MK2 in the p38α signaling pathway.

Distribution analysis of ultra-high molecular mass poly(ethylene oxide) containing silica particles by size-exclusion chromatography with dual light-scattering and refractometric detection.

Two different size-exclusion chromatography (SEC) systems, connected in-line either to a low-angle light scattering (LALS) or to a multiangle light scattering (MALS) detector, are employed for determination of molecular mass distributions (MMD) of poly(ethylene oxide) (PEO) samples having a weight average molecular mass up to eight millions. The detrimental effect of the presence of strongly scattering silica particles in the samples on the light scattering signal can be eliminated using a suitable sample dissolution procedure utilizing silica solubility in aqueous mobile phase. The selection of flow-rate and sample concentration have a large impact on the obtained results. Hydrodynamic retardation phenomena and nonlinearity effects are shown to introduce severe errors in the molecular mass distributions unless flow-rate and sample concentration are kept at sufficiently low levels. Self-compensating ability of the dual detection in flow-rate effects is shown to be the main advantage here. A good agreement between the results obtained using LALS and MALS detection is found provided that a carefully selected angular extrapolation procedure is used in the case of MALS data. Thus, using carefully selected experimental conditions, SEC with light-scattering (LS) and refractometric detection proved to be an efficient technique for MMD characterisation also of ultra-high molecular mass (UHM) PEO polymers.

Molar mass characterization of cationic methyl methacrylate-ethyl acrylate copolymers using size-exclusion chromatography with online multi-angle light scattering and refractometric detection.

Size-exclusion chromatography (SEC) combined with online multi-angle light scattering (MALS) and refractometric (RI) detection has been employed for the molar mass characterisation of water-insoluble cationic methyl methacrylate-ethyl acrylate copolymers (Eudragit RS and RL). Due to their positive charge, cationic polymers are particularly difficult to separate on a SEC column, in worst cases being completely adsorbed on the oppositely charged packing material. This work has examined how a careful addition of salt (LiCl) to the copolymer solution in ethanol decreases the electrostatic interactions, clearly seen as a decrease in elution volume from the SEC column as well as an improved recovery. At a certain level of ionic strength, typically about 50 mM, the copolymer recovery from the SEC column reached 100% and molar mass distributions corresponding to the complete sample could be obtained. The combined MALS/RI detection gives the opportunity to measure the absolute molar mass independent of recovery and retention. Thus, in this study, it turned out to be a favourable tool for tracing the changes in elution behaviour of the charged copolymer as the ionic strength was increased.

The influence of hydroxypropyl methylcellulose (HPMC) molecular weight, concentration and effect of food on in vivo erosion behavior of HPMC matrix tablets.

Four different hydrophilic matrix formulations based on hydroxypropyl methylcellulose (HPMC) were investigated for erosion properties in vivo. Three formulations contained a fixed amount of HPMC (40%) with varying proportions of two HPMC grades with different molecular weights (Methocel K100LV and K4M), and a fourth formulation contained a lower amount of the HPMC of lower molecular weight (20%). The effect of food on the in vivo erosion behavior was investigated on two formulations containing different contents of the same HPMC grade. The in vivo erosion behavior and gastrointestinal transit were investigated using magnetic marker monitoring (MMM). The in vitro and in vivo erosion-time profiles show that the erosion was strongly dependent on the composition of the formulation. The formulations containing a larger proportion of high molecular weight HPMC or higher content of HPMC exhibit relatively slower erosion rate and vice versa. In vivo erosion rates were significantly higher under postprandial administration as compared to fasted state administration. No rapid disintegration of any of the formulations (i.e. formulation failure that can potentially cause dose dumping) was observed.

Polymer leaching from film coating: effects on the coating transport properties.

The release mechanism of metoprolol succinate pellets coated with a blend of a water-insoluble polymer, ethyl cellulose (EC), and a water-soluble polymer, hydroxypropyl cellulose (HPC), is mechanistically explained. The kinetics of drug release and HPC leaching were followed for drug doses. The coating was initially not permeable to the drug, and release started only after a critical amount of the HPC had been leached out. Drug release occurred mainly through pores created in the coating by the HPC dissolution. Single-pellet release experiments were also performed. The coating thickness and size of each pellet were measured. In order to quantitatively characterize the transport properties of the coating of the individual pellets, and to determine the effective diffusion coefficient (D(e)) of the drug in the coating, a mechanistic model was used to fit the single-pellet release data. It was found that D(e) increased with time due to an increase in the amount of HPC leached. It was also found that D(e) was dependent on the coating thickness, and increased more slowly with a thicker coating. This agreed well with the finding that the HPC leaching rate decreased with increasing film thickness.