Voronoi Tessellation as a Tool for Predicting the Formation of Deep Eutectic Solvents.

Deep eutectic solvents (DESs) have attracted increasing attention in recent years due to their broad applicability in different fields, but their computer-aided discovery, which avoids a time-consuming trial-and-error investigation, is still lagging. In this paper, a set of nine DESs, composed of choline chloride as a hydrogen-bond acceptor and nine functionalized phenols as hydrogen bond donors, is simulated by using classical molecular dynamics to investigate the possible formation of a DES. The tool of the Voronoi tessellation analysis is employed for producing an intuitive and straightforward representation of the degree of mixing between the different components of the solutions, therefore permitting the definition of a metric quantifying the propensity of the components to produce a uniform solution. The computational findings agree with the experimental results, thus confirming that the Voronoi tessellation analysis can act as a lightweight yet powerful approach for the high-throughput screening of mixtures in the optics of the new DES design.

Novel ferrofluid based on hydrophobic deep eutectic solvents for separation and analysis of trace estrogens in environmental water and urine samples.

A novel ferrofluid prepared from a hydrophobic deep eutectic solvent (DES) and Fe3O4@graphite composite materials was introduced as a green microextraction medium for the separation and enrichment of trace estrogens in real samples. It was found that the ferrofluid greatly improved the capacity and selectivity of target analytes, benefiting from the enrichment of both DES and Fe3O4@graphite composite materials. Using a combination of high-performance liquid chromatography-fluorescence detection (HPLC-FLD) and vortex-assisted liquid-liquid microextraction (VALLME), a new method was established for simultaneous rapid processing and accurate determination of three estrogens (estradiol [E2], estriol [E3], and ethinyl estradiol [EE2]) in environmental water and urine samples. Key parameters affecting the extraction efficiency were optimized using a single-factor approach and response surface methodology. Under optimal conditions, this method yielded a low limit of detection (1.01 ng L-1, 3.03 ng L-1, and 25.0 ng L-1 for EE2, E2, and E3, respectively), wide linear range (3-200,000 ng L-1), high enrichment factors (9.81-47.2), and satisfactory recovery (73.8-129.0%). Compared with traditional analytical techniques, this method avoids the use of volatile toxic organic extraction solvents and cumbersome phase separation operations.

An eminent approach towards next generation solvents for sustainable packaging and stability of enzymes: a comprehensive study of ionic liquid and deep eutectic solvent mixtures.

Hybrid ionic fluids (HIFs) are newly emerging and fascinating sustainable solvent media, which are attracting a great deal of scientific interest in protecting the native structure of proteins. For a few decades, there has been a demand to consider ionic liquids (ILs) and deep eutectic solvents (DESs) as biocompatible solvent media for enzymes; however, in some cases, these solvent media also show limitations. Therefore, this work focuses on synthesising novel HIFs to intensify the properties of existing ILs and DESs by mixing them. Herein, HIFs have been synthesised by the amalgamation of a deep eutectic solvent (DES) and an ionic liquid (IL) with a common cation or anion. Later on, the stability and activity of hen's egg white lysozyme (Lyz) in the presence of biocompatible solvent media and HIFs were studied by various techniques such as UV-vis, steady-state fluorescence, circular dichroism (CD), Fourier transform infrared spectroscopy (FT-IR) and dynamic light scattering (DLS) measurements. This work emphasises the effect of a DES (synthesised using 1 : 2 choline chloride and malonic acid) [Maline], ILs (1-butyl-3-methylimidazolium chloride [BMIM]Cl or choline acetate [Chn][Ac]) and their corresponding HIFs on the structure and functionality of Lyz. Moreover, we also studied the secondary structure, thermal stability, enzymatic activity and thermodynamic profile of Lyz at pH = 7 in the presence of varying concentrations (0.1 to 0.5 M) of [BMIM]Cl and [Chn][Ac] ILs, Maline as a DES, and Maline [BMIM]Cl (HIF1) and Maline [Chn][Ac] (HIF2). Spectroscopic results elucidate that ILs affect the activity and structural stability of Lyz. In contrast, the stability and activity are inhibited by DES and are enhanced by HIFs at all the studied concentrations. Overall, the experimental results studied explicitly elucidate that the structure and stability of Lyz are maintained in the presence of HIF1 while these properties are intensified in HIF2. This study shows various applications in biocompatible green solvents, particularly in the stability and functionality of proteins, due to their unique combination where the properties counteract the negative effect of either DESs or ILs in HIFs.

Fractionation of oil palm fronds using ethanol-assisted deep eutectic solvent: Influence of ethanol concentration on enhancing enzymatic saccharification and lignin ß-O-4 content.

Numerous fractionation methods have been developed in recent years for separating components such as cellulose, hemicellulose, and lignin from lignocellulosic biomass wastes. Deep eutectic solvents (DES) have recently been widely investigated as captivating green solvents for biomass fractionation. However, most acidic-based deep eutectic solvent fractionation produces condensed lignin with low ß-O-4 content. Besides, most DESs exhibit high viscosity, which results in poor mass transfer properties. This study aimed to address the challenges above by incorporating ethanol into the deep eutectic solvent at various concentrations (10-50 wt%) to fractionate oil palm fronds at a mild condition, i.e., 80 °C, 1 atm. Cellulose residues fractionated with ethanol-assisted deep eutectic solvent showed a maximum glucose yield of 85.8% when 20 wt% of ethanol was incorporated in the deep eutectic solvent, significantly higher than that achieved by pure DES (44.8%). Lignin extracted with ethanol-assisted deep eutectic solvent is lighter in color and higher in ß-O-4 contents (up to 44 ß-O-4 per 100 aromatic units) than pure DES-extracted lignin. Overall, this study has demonstrated that incorporating ethanol into deep eutectic solvents could enhance the applicability of deep eutectic solvents in the complete valorization of lignocellulosic biomass. Highly enzymatic digestible cellulose-rich solid and ß-O-4-rich lignin attained from the fractionation could serve as sustainable precursors for the production of biofuels.

Evaluation of the difference in adsorption of amphetamine-type drugs on deep eutectic solvent-functionalized graphene oxide/ZIF-67 composite: Experiment and theoretical calculations.

Herein, the capture and separation properties of the deep eutectic solvent-functionalized magnetic graphene oxide/ZIF-67 composite (ZMG-DES) towards amphetamine-type drugs (MDMA, MAM and AM) from water were investigated. Kinetic and isotherm models showed that the adsorption behaviors were monolayer chemisorption. Batch experiment results showed that the maximal adsorption of MDMA (933.652 µg⋅g-1) was 2.3 and 2.8 times higher than that of MAM (412.849 µg⋅g-1) and AM (328.652 µg⋅g-1), respectively, and this superiority remained consistent under varied environmental influences (pH, background ion and humic acid). Theoretical calculations and characterization analyses demonstrated the methylenedioxy group of MDMA led to the highly selective adsorption. Electrostatic potential (ESP) distribution indicated that the methylenedioxy added electron-rich areas and provided more adsorption sites. The Independent Gradient Model (IGMH) quantified the adsorption contribution of the functional groups in each system, which the contribution of the methylenedioxy reached 25.23%, significantly exceeding that of -NH- (18.80%) and benzene ring (20.76%), and proved that the H-bonds formed methylenedioxy enhanced adsorption. Furthermore, the Hirshfeld surface analysis proved that the methylenedioxy and -NH- of MDMA acted as H-bond acceptor and donor, respectively, which synergistically promoted the adsorption. The present study will help us to understand the structure-property relationship between amphetamine-type drugs and ZMG-DES.

Application of deep eutectic solvents on extraction of flavonoids.

Deep eutectic solvents (DESs), as a new type of eco-friendly solvent, have attracted increasing attention on the extraction and separation of flavonoid compounds from various samples, owing to their excellent properties such as biodegradability and ease of handling with very low toxicity. This article provides a status review of the applications of DESs in the extraction of flavonoids, including the introduction of flavonoid compounds, the properties and superiority of DESs, and extraction methods (ultrasonic-assisted extraction, heating reflux extraction, matrix solid-phase dispersion, and solid-phase extraction). Finally, prospects and challenges in the application of DESs on extraction and separation are extensively elucidated and critically reviewed.

Amino acids-based deep eutectic solvents as additives for improved enantioseparation in capillary electrophoresis.

In this study, several amino acids deep eutectic solvents were prepared using L-valine and L-leucine as hydrogen bond acceptors, and L-lactic acid and glycerol as hydrogen bond donors. These amino acids' deep eutectic solvents were first used as buffer additives to construct several synergistic systems along with maltodextrin in capillary electrophoresis for the enantioseparations of four racemic drugs. Compared with single maltodextrin system, the separations of model drugs in the synergistic systems were significantly improved. Some key parameters affecting chiral separation such as maltodextrin concentration, deep eutectic solvent concentration, buffer pH, and applied voltage were optimized. In order to further understand the specific mechanism of the amino acids deep eutectic solvents in improving chiral separation, we first calculated the binding constants of maltodextrin with enantiomers using the capillary electrophoresis method in the two separation modes, respectively. We also used molecular simulation to calculate the binding free energy of maltodextrin with enantiomers. It is the first time that amino acids deep eutectic solvents were used for enantioseparation in capillary electrophoresis, which will greatly promote the development of deep eutectic solvents in the field of chiral separation.

Development of analytical method for determination of 1,3-dimethylamylamine in sports nutrition and bodybuilding supplements using pH-switchable deep eutectic solvents followed by high-performance liquid chromatography-diode array detector.

In this work, an easy, safe, simple, and efficient pH-switchable deep eutectic solvents (DESs)-based liquid phase microextraction followed by high-performance liquid chromatography-diode array detector analysis was developed for the determination of 1,3-dimethylamylamine (DMAA). The switchability of the obtained DESs was investigated by changing the pH. Then the best-selected DES was characterized and the application of the selected DES in the extraction of DMAA from sports nutrition and bodybuilding supplements was investigated. The DES synthesized from l-menthol: oleic acid in a molar ratio of 1:2 had the highest efficiency in the extraction of the target compound. Under the optimum conditions, (50 µL of DES, 100 µL of 4 mol/L KOH, 100 µL of 4 mol/L HCl, extraction time of 40 s and without salt addition) the calibration graph was linear in the range of 0.05-100 µg/kg and limit of detection was 0.02 µg/kg. The relative standard deviations including intra-day and inter-day for 10.0 µg/kg of DMAA in real samples were 2.7% (n = 7) and 5.3% (n = 7), respectively. The enrichment factor and percentage extraction recovery of the method were 283 and 85%, respectively. The relative recoveries for DMAA in different samples were in the range of 90%-109%.

Preconcentration of Cinnamic Acid Derivatives in Traditional Chinese Medicines by an Effective Dispersive Liquid-Liquid Microextraction Based on a Hydrophobic Deep Eutectic Solvent.

A dispersive liquid-liquid microextraction based on hydrophobic deep eutectic solvent (hDES) was developed for the extraction and quantification of four cinnamic acid derivatives in traditional Chinese medicines coupled with high-performance liquid chromatography-ultraviolet detection. In this method, a hDES (tetrabutylammonium chloride-hexanoic acid, molar ratio of 1:2) was prepared as the extractant. It only took 15 s to handle multiple samples simultaneously by hand-assisted dispersion. The use of a narrow-bore tube reduced the amount of the hydrophobic extractant with easier recovery. The approach was influenced by several key parameters, including the composition and consumption of the DES, sample phase pH, salt amount, extraction time, and centrifugation time, all of which had been investigated and optimized. Moreover, the formation of the DES was characterized by Fourier-transform infrared spectroscopy and differential scanning calorimetry. Under the optimal conditions, enrichment factors of the target analytes ranged from 135 to 220. Satisfactory linearities (r ≥ 0.9977), detection limits (0.2-0.4 ng/mL), precision (<8.5%), and accuracy (recoveries: 90.0%-104.6%) were obtained. The method has been successfully applied to the simultaneous extraction and preconcentration of four cinnamic acid derivatives in Chinese medicinal samples with rapidness, high efficiency, and convenience.

Ultrasound-assisted matrix solid-phase extraction based on deep eutectic solvents and zinc oxide: Extraction and determination of six active ingredients in Ligustri Lucidi Fructus.

In this study, we propose a novel strategy utilizing deep eutectic solvents (DESs) as both the extraction solvent and dispersing liquid, with nanometer zinc oxide (ZnO) serving as the adsorbent. This method incorporates ultrasound-assisted matrix solid phase dispersion (UA-MSPD) for the extraction of six active components (salidroside, echinacoside, acteoside, specnuezhenide, nuezhenoside G13, and oleanolic acid) from Ligustri Lucidi Fructus samples. The extracts were then analyzed using high-performance liquid chromatography equipped with a diode array detector. The effects of various parameters such as dispersant dosage, DESs volume, grinding time, ultrasonication duration, and eluent volume on extraction recovery were investigated and optimized using a central composite design under response surface methodology. The optimized conditions yielded detection limits ranging from 0.003 to 0.01 mg/g and relative standard deviations of 8.7% or lower. Extraction recoveries varied between 93% and 98%. The method demonstrated excellent linearity for the analytes (R2 ≥ 0.9997). The simple, green, and efficient DESs/ZnO-UA-MSPD technique proved to be rapid, accurate, and reliable for extracting and analyzing the six active ingredients in Ligustri Lucidi Fructus samples.

Innovative Alkanediol-Based Eutectic Solvents for Extracting/Pre-Formulating Dermatologically Valuable Free Fatty Acids from Spirulina and Porphyridium Cakes.

The growing demand for phycobiliproteins from microalgae generates a significant volume of by-products, such as extraction cakes. These cakes are enriched with products of interest for the cosmetics market, namely free fatty acids, particularly polyunsaturated (PUFA). In this work, two cakes, one of spirulina and one of Porphyridium cruentum, were valorized using innovative natural hydrophobic deep eutectic solvents (NaDES) based on alkanediols. The most promising NaDES, as determined by physicochemical properties and screening, are mixtures of alkanediols and fatty acids. These include the mixtures of 1,3-propanediol and octanoic acid (1:5, mol/mol) and 1,3-propanediol and octanoic and decanoic acid (1:3:1, mol/mol). Two extractive processes were implemented: ultrasound-assisted extraction and an innovative mechanical process involving dual asymmetric centrifugation. The second process resulted in the production of extracts significantly enriched in PUFA, ranging from 65 to 220 mg/g dry matter with the two cakes. The extracts and NaDES demonstrated good safety with respect to epidermal keratinocyte viability (>80% at 200 µg/mL). The study of their impact on commensal and pathogenic cutaneous bacteria demonstrated significant effects on the viability of Staphylococcus aureus and Staphylococcus epidermidis (>50% decrease at 200 µg/mL) while preserving Corynebacterium xerosis and Cutibacterium acnes. These results highlight the potential of valorizing these co-products using alkanediol-based NaDES, in a strategy combining an active vector (NaDES) and a growth regulator extract, for the management of cutaneous dysbiosis involving staphylococci.

Hydrophobic eutectic solvents for surface water treatment with a focus on benzophenone type UV filters.

Effective removal of organic UV filters from aquatic environmental compartments and swimming waters is very important because these substances are hazardous to humans and wildlife at low concentrations and act as endocrine disruptors. Therefore, the aim of the present article is to determine the extraction efficiencies of hydrophobic deep eutectic solvents (HDES) for the selected UV filters based on benzophenone structure (benzophenone, 2,4-dihydroxybenzophenone, 2,2´,4,4´-tetrahydroxybenzophenone, 2-hydroxy-4-methoxybenzophenone, 2,2´-dihydroxy-4-methoxybenzophenone, 4-methacryloxy-2-hydroxybenzophenone) from aqueous matrices. For this purpose, six HDESs based on dl-menthol in combination with caprylic, decanoic and lauric acid are prepared and compared with referent terpene solvents such as terpineol and linalool. The effect of various parameters such as HDES composition, volume ratio, frequency and shaking time are studied. The highest extraction efficiency is shown by HDES of menthol:caprylic acid (1:1) composition at the aqueous:organic phase volume ratio of 1:1, shaking frequency of 1500 rpm and shaking time of 15 min. The achieved extraction efficiencies are higher than 99.6 % for all benzophenones studied in the purification of stagnant pond water, swimming pool water and river water samples. After a simple and fast sample treatment, the residual levels of benzophenones in the waters are controlled by a newly developed sensitive HPLC-MS/MS method with LOQs in the range of 0.7 - 5.0 ng/mL.

Extraction of Lentinus Edodes Polysaccharides with Ultrasound Enhanced with Deep Eutectic Solvent and Their Structural Characterization and Antioxidant Activity.

Ultrasound extraction (UE) enhanced with deep eutectic solvent (DES) was used to extract Lentinus edodes polysaccharides. Box-Behnken design (BBD) was applied to investigate the influences of water content (10-90 %), solid-liquid solvent (1 : 10-1 : 50 g/mL), time (4-12 min), temperature (40-80 °C) and ultrasonic power (100-500 W) on the yield of Lentinus edodes polysaccharides. The optimal extraction conditions were ultrasonic power of 300 W, extraction time of 8 min, water content of 80 %, a solid-liquid ratio of 1 : 30 g/mL and a temperature of 60 °C, respectively. The highest extraction yield of Lentinus edodes polysaccharide was 10.17 % under optimal conditions. The results of FT-IR, SEM, and monosaccharide composition confirmed that the extracts possessed the characteristics of polysaccharides. In addition, the polysaccharides obtained with the UE enhanced with DES method exhibited higher antioxidant activities than the polysaccharides extracted with the UE method and HWE method. This extraction method can further expand the production efficiency and structural diversity of Lentinus edodes polysaccharides and meet the supply and demand relationship. It can be foreseen that this method can be applied to the extraction of more active substances.

Synthesis of ultrasmall cerium oxide nanoparticles in deep eutectic solvent and their application in an electrochemical sensor to detect dopamine in biological fluid.

A solvothermal synthesis of ultrasmall cerium oxide nanoparticles (USCeOxNPs) with an average size of 0.73 ± 0.07 nm using deep eutectic solvent (DES) as a stabilizing medium at a temperature of 90 ºC is reported. Transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS) were used to morphologically characterize the USCeOxNPs. These revealed approximately spherical shapes with emission lines characteristic of cerium. Selected area electron diffraction (SAED) was used to determine the crystalline structure of the cerium oxide nanoparticles (CeO2NPs), revealing the presence of crystalline cubic structures. The USCeOxNPs-DES/CB film was characterized by scanning electron microscopy (SEM), which demonstrated the spherical characteristic of CB with layers slightly covered by DES residues. DES was characterized by Fourier transform infrared (FT-IR) and nuclear magnetic resonance (NMR), indicating its formation through hydrogen bonds between the precursors. An electrochemical sensor for dopamine (DA) determination in biological fluids was developed using the USCeOxNPs together with carbon black (CB). An enhanced current response was observed on DA voltammetric determination, and this can be attributed to the USCeOxNPs. This sensor displayed linear responses for DA in the range 5.0 × 10-7 mol L-1 to 3.2 × 10-4 mol L-1, with a limit of detection of 80 nmol L-1. Besides detectability, excellent performances were verified for repeatability and anti-interference. The sensor based on USCeOxNPs synthesized in DES in a simpler and environmentally friendly way was successfully applied to determine DA in biological matrix.

Natural deep eutectic solvent-functionalized mesoporous graphitic carbon nitride-reinforced electrospun nanofiber: a promising sorbent in miniaturized on-chip thin film micro-solid-phase extraction prior to liquid chromatography-tandem mass spectrometry for measuring NSAIDs in saliva.

To meet the needs of developing efficient extractive materials alongside the evolution of miniaturized sorbent-based sample preparation techniques, a mesoporous structure of g-C3N4 doped with sulfur as a heteroatom was achieved utilizing a bubble template approach while avoiding the severe conditions of other methods. In an effort to increase the number of adsorption sites, the resultant exfoliated structure was then modified with thymol-coumarin NADES as a natural sorbent modifier, followed by introduction into a nylon 6 polymer via an electrospinning process. X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, field-emission scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET) surface area analysis validated S-doped g-C3N4 and composite production. The prepared electrospun fiber nanocomposite, entailing satisfactory processability, was then successfully utilized as a sorbent in on-chip thin film micro-solid-phase extraction of non-steroidal anti-inflammatory drugs (NSAIDs) from saliva samples prior to liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. Utilizing a chip device, a thin film µ-SPE coupled with LC-MS/MS analysis yielded promising outcomes with reduced sample solution and organic solvents while extending lifetime of a thin film sorbent. The DES-modified S-doped g-C3N4 amount in electrospun was optimized, along with adsorption and desorption variables. Under optimal conditions, selected NSAIDs were found to have a linear range of 0.05-100.0 ng mL-1 with an R2 ≥ 0.997. The detection limits were ranged between 0.02 and 0.2 ng mL-1. The intra-day and inter-day precisions obtained were less than 6.0%. Relative recoveries were between 93.3 and 111.4%.

Preparation of deep eutectic solvent modified magnetic graphene oxide/metal organic framework nanocomposites for the extraction of three estrogens in cosmetics.

A novel magnetic dispersive solid phase extraction (MDSPE) procedure based on the deep eutectic solvent (DES) modified magnetic graphene oxide/metal organic frameworks nanocomposites (MGO@ZIF-8@DES) was established and used for the efficient enrichment of estradiol, estrone, and diethylstilbestrol in cosmetics (toner, lotion, and cream) for the first time. Then, the three estrogens were separated and determined by UHPLC-UV analysis method. In order to study the features and morphology of the synthesized adsorbents, various techniques such as FT-IR, SEM, and VSM measurements were executed. The MGO@ZIF-8@DES nanocomposites combine the advantages of high adsorption capacity, adequate stability in aqueous solution, and convenient separation from the sample solution. To achieve high extraction recoveries, the Box-Behnken design and single factor experiment were applied in the experimental design. Under the optimum conditions, the method detection limits for three estrogens were 20-30 ng g-1. This approach showed a good correlation coefficient (r more than 0.9998) and reasonable linearity in the range 70-10000 ng g-1. The relative standard deviations for intra-day and inter-day were beneath 7.5% and 8.9%, respectively. The developed MDSPE-UHPLC-UV method was successfully used to determine  three estrogens in cosmetics, and acceptable recoveries in the intervals of 83.5-95.9% were obtained. Finally, three estrogens were not detected in some cosmetic samples. In addition, the Complex GAPI tool was used to evaluate the greenness of the developed pretreatment method. The developed MDSPE-UHPLC-UV method is sensitive, accurate, rapid, and eco-friendly, which provides a promising strategy for determining hormones in different complex samples.

Biotransformation of ginsenoside compound K using ß-glucosidase in deep eutectic solvents.

Ginsenoside compound K (CK) holds significant potential for application in the pharmaceutical industry, which exhibits numerous pharmacological activity such as cardioprotective and antidiabetic. However, the difficult separation technique and limited yield of CK hinder its widespread use. The study investigated the process of converting ginsenoside CK using ß-glucosidase. It aimed to determine the specific site where the enzyme binds and the most favorable arrangement of the enzyme. Molecular docking was also employed to determine the interaction between ß-glucosidase and ginsenosides, indicating a strong and spontaneous contact force between them. The effectiveness of the conversion process was further improved using a "green" deep eutectic solvent (DES). A univariate experimental design was used to determine the composition of DES and the optimal hydrolysis conditions for ß-glucosidase to convert ginsenoside Rb1 into ginsenoside CK. The employment of ß-glucosidase enzymatic hydrolysis in the synthesis of rare ginsenoside CK applying the environmentally friendly solvent DES is not only viable and effective but also appropriate for industrial use. The characterization methods confirmed that DES did not disrupt the structure and conformation of ß-glucosidase. In ChCl:EG = 2:1 (30%, v/v), pH 5.0 of DES buffer, reaction temperature 50 ℃, enzyme substrate mass ratio 1:1, after 36 h of reaction, the CK yield was 1.24 times that in acetate buffer, which can reach 86.2%. In this study, the process of using ß-glucosidase enzymatic hydrolysis and producing rare ginsenoside CK in green solvent DES is feasible, efficient and suitable for industrial production and application.

Extraction and characterisation of kudzu root residue lignin based on deep eutectic solvents.

INTRODUCTION: Lignin has great potential as the most abundant renewable phenolic polymer. Studies have shown that lignin structure varies depending on different sources and different extraction methods. However, there are few studies on lignin in kudzu root residue. OBJECTIVES: The aim of the study was to explore optimal extraction conditions of Pueraria lobata residue lignin (PLL) with deep eutectic solvents (DESs) and characterise the structure and morphology of PLL. METHODS: Firstly, the chemical composition of kudzu root residue was determined by the Van-soest method. Then, betaine was used as hydrogen bond acceptor (HBA), nine kinds of common acids and alcohol were selected as hydrogen bond donor (HBD) to synthesise a DES to extract lignin from kudzu root residue. The influence of conditions on the extraction of PLL was explored by a betaine-based DES according to a single-factor experiment, and then the best process of PLL extraction was determined by an orthogonal experiment. Finally, the morphology and structure of PLL were analysed by scanning electron microscope (SEM), thermogravimetric analysis (TGA), gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), and NMR. RESULTS: Cellulose, hemicellulose, lignin, and ash content in kudzu root residue were 41.13%, 16.39%, 25.03%, and 0.41%, respectively. When the DES consisted of betaine and formic acid, the solid-liquid ratio was 1:45, the extraction time was 5.5 h at 160°C, the extraction yield of lignin was 89.29%, and the purity was 83.01%. PLL was composed of interconnected spherical particles with good thermal stability and narrow polydispersity index (PDI) distribution. FTIR and 2D-heteronuclear singular quantum correlation (HSQC) NMR illustrated that PLL was a typical G-type and S-type lignin. CONCLUSION: This study would fill the gap of research on lignin in kudzu root residue and provide a theoretical reference for the utilisation of lignin in kudzu roots as well as a new thinking for the recycling of kudzu root resources.

Eutectic solutions for healing: a comprehensive review on therapeutic deep eutectic solvents (TheDES).

OBJECTIVE: TheDES are formed by mixing a Hydrogen Bond Donor (HBD) and a Hydrogen Bond Acceptor (HBA) in appropriate molar ratios. These solvents have been shown to enhance drug solubility, permeability, and delivery. The main objective of the present article is to review these advantages of TheDES. SIGNIFICANCE: TheDES show unique properties, such as low toxicity, biodegradability, improved bioavailability and enhanced drug delivery of poorly soluble active pharmaceutical ingredients. They are also biocompatible in nature which makes them a promising candidate for various therapeutic applications, including drug formulations, drug delivery and other biomedical uses. The development and utilization of TheDES shows significant advancement in pharmaceutical research, providing new opportunities for improving drug delivery. METHODS: The current study was carried out by conducting a systematic literature review that identified relevant papers from indexed databases. Numerous studies and research are cited and quoted in this article to demonstrate the effectiveness of TheDES in enhancing drug solubility, permeability, and delivery. All chosen articles were selected considering their significance, quality, and approach to addressing issues. RESULT: As a result, various TheDES were identified that can be formulated in different ways: one component can act as a vehicle for an API, either HBD or HBA can be an API, both HBD and HBA can be APIs, or the individual components of DES are not therapeutically active but the resulting DES possesses therapeutic activity. Additionally, TheDES were also recognized to enhance drug delivery and solubility for different APIs, including NSAIDs, anesthetic drugs, antifungals, and others.

Sustainable Synthesis of the Active Pharmaceutical Ingredient Atenolol in Deep Eutectic Solvents.

Atenolol, one of the top five best-selling drugs in the world today used to treat angina and hypertension, and to reduce the risk of death after a heart attack, faces challenges in current synthetic methods to address inefficiencies and environmental concerns. The traditional synthesis of this drug involves a process that generates a large amount of waste and other by-products that need disposal. This study presents a one-pot DES-based sustainable protocol for synthesizing atenolol. The use of the DES allowed the entire process to be conducted with no need for additional bases or catalysts, in short reaction times, under mild conditions, and avoiding chromatographic purification. The overall yield of atenolol was 95%. The scalability of the process to gram-scale production was successfully demonstrated, emphasizing its potential in industrial applications. Finally, the 'greenness' evaluation, performed using the First Pass CHEM21 Metrics Toolkit, highlighted the superiority in terms of the atom economy, the reaction mass efficiency, and the overall process mass intensity of the DES-based synthesis compared with the already existing methods.