Risk assessment of heavy metals and total petroleum hydrocarbons (TPHs) in coastal sediments of commercial and industrial areas of Hormozgan province, Iran.

The significant increase in the pollution of heavy metals and organic pollutants, their stable nature, and their high toxicity are gradually becoming a global crisis. In a recent study, a comprehensive assessment of the spatial distribution of heavy metals and total petroleum hydrocarbons (TPHs), as well as an assessment of their ecological risks in the sediments of 32 stations located in commercial and industrial areas (Mainly focusing on petrochemical and power industries, desalination plants and transit Ports) of Hormozgan province (East and West of Jask, Bandar Abbas, Qeshm, and Bandar Lengeh) was performed during 2021-2022. The sediment samples were digested with HNO3, HCl and HF solvents. The concentration of heavy metals was determined with furnace and flame systems of atomic absorption spectrometer. The concentration of heavy metals showed significant spatial changes between stations. The ecological assessment indices between the regions indicated that the stations located in Shahid Bahonar Port, Suru Beach, and Khor gorsouzuan had a higher intensity of pollution than other places and significant risks of pollution, especially in terms of Cr and Ni. The average contamination degree (CD) (14.89), modified contamination degree (MCD) (2.48), pollution load index (PLI) (2.32), and potential ecological risk index (PERI) (100.30) showed the sediments in the area of Shahid Bahonar Port, Suru beach and Khor gorsouzuan, experience significant to high levels of pollution, especially Cr and Ni. Using contamination factor (CF) and Geoaccumulation index (Igeo), Cr was considered the most dangerous metal in the studied areas. Based on the global classification of marine sediment quality for the concentrations of TPHs, the sediments of the studied stations were classified as non-polluted to low pollution. In all regions, indices of the PELq (General toxicity) and CF (Contamination factor) were much lower than 0.1 and 1 respectively, showing the absence of adverse biological effects caused by TPHs in sediments. It is necessary to consider comprehensive and impressive strategies to control and reduce pollution of heavy metals, especially in the areas of Shahid Bahonar Port, Suru Beach, and Khor gorsouzuan, so that the sources of this pollution are required to be identified and managed.

A simple protocol for estimating the acute toxicity of unresolved polar compounds from field-weathered oils.

Crude oil spilled at sea is chemically altered through environmental processes such as dissolution, biodegradation, and photodegradation. Transformation of hydrocarbons to oxygenated species increases water-solubility. Metabolites and oxidation products largely remain uncharacterized by common analytical methods but may be more bioavailable to aquatic organisms. Studies have shown that unresolved (i.e. unidentified) polar compounds ('UPCs') may constitute > 90% of the water-accommodated fraction (WAF) of heavily weathered crude oils, but still there is a paucity of information characterizing their toxicological significance in relation to other oil-derived toxicants. In this study, low-energy WAFs (no droplets) were generated from two field-weathered oils (collected during the 2010 Deepwater Horizon incident) and their polar fractions were isolated through fractionation. To allow establishment of thresholds for acute toxicity (LC50) of the dissolved and polar fraction of field collected oils, we concentrated both WAFs and polar fractions to beyond field-documented concentrations, and the acute toxicity of both to the marine copepod Acartia tonsa was measured and compared to the toxicity of the native WAF (non-concentrated). The difference in toxic units (TUs) between the total of the mixture and of identified compounds of known toxicity (polycyclic aromatic hydrocarbons [PAHs] and alkyl phenols) in both WAF and polar fractions was used to estimate the contribution of the UPC to overall toxicity. This approach identified that UPC had a similar contribution to toxicity as identified compounds within the WAFs of the field-weathered oils. This signifies the relative importance of polar compounds when assessing environmental impacts of spilled and weathered oil.

Use of TLM derived models to estimate toxicity of weathered MC252 oil based on conventional chemical data and the potential impact of unresolved polar components.

Target lipid model (TLM) and toxic unit (TU) approaches were applied to ecotoxicity and chemistry data from low-energy WAFs (LE-WAFs) of source and weathered crude oils originating from the Deepwater Horizon oil spill. The weathered oils included artificially weathered oils and naturally weathered samples collected in the Gulf of Mexico after the spill. Oil weathering greatly reduced the concentrations of identified LE-WAF components, however, the mass of uncharacterized polar material (UPC) in the LE-WAFs remained largely unchanged during the weathering process. While the TLM-derived calculations displayed a significant decrease in toxicity (TUs) for the heavily weathered oils, copepod toxicity, expressed as LC10-based TUs, were comparable between LE-WAFs of fresh and weathered oils. The discrepancy between observed and predicted toxicity for the LE-WAFs of artificially weathered oils may be related to limitations by the chemical analyses or increased toxicity due to generation of new unknown compounds during the weathering process.

Assessing petroleum contamination in parts of the Niger Delta based on a sub-catchment delineated field assessment.

The Niger Delta in Nigeria is a complex and heavily contaminated area with over 150,000 interconnected contaminated sites. This intricate issue is compounded by the region's strong hydrological processes and high-energy environment, necessitating a science-based approach for effective contamination assessment and management. This study introduces the concept of sub-catchment contamination assessment and management, providing an overarching perspective rather than addressing each site individually. A description of the sub-catchment delineation process using the digital elevation model data from an impacted area within the Delta is provided. Additionally, the contamination status from the delineated sub-catchment is reported. Sediment, surface water and groundwater samples from the sub-catchment were analyzed for total petroleum hydrocarbons (TPH) and polycyclic aromatic hydrocarbons (PAHs), respectively. Surface sediment TPH concentrations ranged from 129 to 20,600 mg/kg, with subsurface (2-m depth) concentrations from 15.5 to 729 mg/kg. PAHs in surface and subsurface sediment reached 9.55 mg/kg and 0.46 mg/kg, respectively. Surface water exhibited TPH concentrations from 10 to 620 mg/L, while PAHs ranged from below detection limits to 1 mg/L. Groundwater TPH concentrations spanned 3 to 473 mg/L, with total PAHs varying from below detection limits to 0.28 mg/L. These elevated TPH and PAH levels indicate extensive petroleum contamination in the investigated sediment and water environment. Along with severe impacts on large areas of mangroves and wetlands, comparison of TPH and PAH concentrations with sediment and water quality criteria found 54 to 100% of stations demonstrated exceedances, suggesting adverse biological effects on aquatic and sediment biota are likely occurring.

Reusable Sugar-Based Gelator for Marine Oil-Spill Recovery and Waste Water Treatment.

In this work, the gelation ability of a series of novel pyridine-based glucose tailored gelators (DPHAEN, DPHABN, and DPHAHN) with a flexible alkyl chain has been examined in binary solvent mixtures using a number of techniques, for example, UV spectroscopy, FT-IR spectroscopy, NMR spectroscopy, rheology measurement, SEM, XRD, and computational study. Proposed herein is an environment-friendly method to realize toxic dye separation and oil/water separation. It has been found that gels in a selective binary solvent mixture are efficient reusable absorbers of toxic dye molecules. A new gravitational force-driven, simple one-step, toxic dye removal and oil-water separation method is presented for sustainable filtration of waste water and simultaneous collection of oil. The gel column also showed high stability and reusability over repeated use and can be easily scaled for efficient clean-up of a large number of toxic dyes and oil spills present in water. Studies also exposed that the gel column can simultaneously separate dye molecules and mineral oils from water. This simple, green, and efficient method overcomes a nontrivial hurdle for environmentally safe separation of toxic dyes as well as oil/water mixtures and offers insights into the design of advanced materials for practical oil/water separation.

An experimental oil spill at a tidal freshwater wetland along the St. Lawrence River re-visited after 21 years.

In 1999, a tidal wetland located along the St. Lawrence River close to Ste. Croix de Lotbinière (Quebec, Eastern Canada) was the site of an experimental oil spill. Test plots were established and subjected to an experimental crude oil spill to evaluate natural attenuation, nutrient amendment and vegetation cropping as countermeasures. In 2020, this study re-visited the test plots to investigate residual oil and habitat recovery. Only concentrations of mid-chain length n-alkanes (C10-C36), but not of polycyclic aromatic hydrocarbons (PAHs), were significantly above detection limit, and were detected in both test plot and control sediments. Hydrocarbon, total organic carbon, nitrogen and phosphate contents did not differ significantly between test plot and control sediments. Microbial analyses did not detect significant differences in microbial load, microbial diversity or microbial community composition between test plot and control sediments. Key genes for the aerobic and anaerobic degradation of n-alkanes as well as for the aerobic degradation of PAHs were detected in all sediment samples. Associated gene abundances did not differ significantly between test plot and control sediments. This study shows that oil-exposed test plot sediments of the Ste. Croix wetland can be considered completely recovered after 21 years irrespective of the performed countermeasure.

In Situ Burning for Oil Spill Response in the Arctic: Recovery and Quantification of Chemical Herding Agent OP-40 from Burned Oil Residues.

In situ burning (ISB) aided by OP-40 is one of the best suited and effective oil spill response techniques for Arctic conditions. However, the fate of OP-40 in the environment after an ISB event is not fully understood, especially the amount of OP-40 remaining within the burned oil residues. Previous studies reported partial accumulation of OP-40 in water, and no OP-40 was measured in the air emissions following the burn. Accumulation of OP-40 in burned oil residues is not appropriately quantified as it is challenging to process and analyze burned oil samples in the laboratory, and there exists no standard method in the literature to measure and quantify OP-40 in burned residues. In this work, we report on the development of an analytical method for the quantification of OP-40 in burned oil residues using column chromatography, followed by gas chromatography-mass spectrometry analysis which was successfully employed to measure more than 90% of the applied OP-40 in the burned residues for controlled bench-scale burns. Additionally, the robustness of the developed method was further tested by measuring OP-40 in burn residues from ISBs conducted at different oil-water emulsion ratios (60-100% oil) and water temperatures (4-35 °C), wherein known amounts of OP-40 were added to the residues. Results indicate that the method is equally effective for different oil-water emulsions, but the OP-40 recoveries (89.2-115.6%) are significantly higher at warmer temperatures than the OP-40 recoveries (87.0-103.3%) at colder temperatures. Overall, the method developed in this work could assist in the understanding of the fate of OP-40 in a potentially important environmental matrix of burned oil residues that are left behind sometimes long (weeks to years) after an ISB event.

Shaping the concentration of petroleum hydrocarbon pollution in soil: A machine learning and resistivity-based prediction method.

A new method relying on machine learning and resistivity to predict concentrations of petroleum hydrocarbon pollution in soil was proposed as a means of investigation and monitoring. Currently, determining pollutant concentrations in soil is primarily achieved through costly sampling and testing of numerous borehole samples, which carries the risk of further contamination by penetrating the aquifer. Additionally, conventional petroleum hydrocarbon geophysical surveys struggle to establish a correlation between survey results and pollutant concentration. To overcome these limitations, three machine learning models (KNN, RF, and XGBOOST) were combined with the geoelectrical method to predict petroleum hydrocarbon concentrations in the source area. The results demonstrate that the resistivity-based prediction method utilizing machine learning is effective, as validated by R-squared values of 0.91 and 0.94 for the test and validation sets, respectively, and a root mean squared error of 0.19. Furthermore, this study confirmed the feasibility of the approach using actual site data, along with a discussion of its advantages and limitations, establishing it as an inexpensive option to investigate and monitor changes in petroleum hydrocarbon concentration in soil.

Experimental investigation on electromagnetic induction thermal desorption for remediation of petroleum hydrocarbons contaminated soil.

A novel electromagnetic induction low temperature thermal desorption treatment (EMI LTTD) for petroleum hydrocarbons contaminated soil was introduced in this work. The removal rate of total petroleum hydrocarbons (TPH) under various factors, the morphology changes of soils as well as removal mechanism were investigated. Results suggested that increasing the heating temperature significantly increased the removal rate of TPH. At the beginning of 20 min, most of hydrocarbons (93.44-96.91 wt%) was removed with the temperature ranged from 200 °C to 300 °C. Besides, the initial contaminants concentration, particle size and thickness of soil slightly influenced the removal rate of TPH. Desorption kinetic study demonstrated that first-order model was well-described for desorption behavior. Response surface methodology analysis showed the temperature of 216 °C, the residence time of 21 min and the moisture content of 18% was an optimum condition recommended for potentially practical application. Under this condition, the results for the composition of hydrocarbons based on carbon number fractions indicated that the fractions of C10∼C16, C17∼C22 still existed in soil, while C23∼C28 was not detected after EMI LTTD treatment. Proposed mechanism was both hydrocarbons removed by evaporation at any temperature, while parts of heavy hydrocarbons was cracked within the soil close to induction medium, resulting in re-adsorption of light hydrocarbons. A buckwheat germination and growth test indicated that soil treated by EMI LTTD was potential in reutilization for planting.

Biocompatible and Biodegradable Surfactants from Orange Peel for Oil Spill Remediation.

Oil spill remediation plays a vital role in mitigating the environmental impacts caused by oil spills. The chemical method is one of the widely recognized approaches in chemical surfactants. However, the most commonly used chemical surfactants are toxic and non-biodegradable. Herein, two biocompatible and biodegradable surfactants were synthesized from orange peel using the ionic liquid 1-butyl-3-methylimidazolium chloride (BMIMCl) and organic solvent dimethylacetamide (CH3CN(CH3)2) as reaction media. The acronyms SOPIL and SOPOS refer to the surfactants prepared with BMIMCl and dimethylacetamide, respectively. The surface tension, dispersant effectiveness, optical microscopy, and emulsion stability test were conducted to examine the comparative performance of the synthesized surfactants. The Baffled flask test (BFT) was carried out to determine the dispersion effectiveness. The toxicity test was performed against zebrafish (Danio rerio), whereas the closed bottle test (CBT) evaluated biodegradability. The results revealed that the critical micelle concentration (CMC) value of SOPIL was lower (8.57 mg/L) than that of SOPOS (9.42 mg/L). The dispersion effectiveness values for SOPIL and SOPOS were 69.78% and 40.30%, respectively. The acute toxicity test demonstrated that SOPIL was 'practically non-toxic' with a median lethal concentration of more than 1000 mg/L after 96 h. The biodegradation rate was recorded as higher than 60% for both surfactants within 28 days, demonstrating their readily biodegradable nature. Considering these attributes, biocompatible and biodegradable surfactants derived from orange peel emerge as a promising and sustainable alternative for oil spill remediation.

Bioaugmentation enhance the bioremediation of marine crude oil pollution: Microbial communities and metabolic pathways.

Bioaugmentation is an effective strategy used to speed up the bioremediation of marine oil spills. In the present study, a highly efficient petroleum degrading bacterium (Pseudomonas aeruginosa ZS1) was applied to the bioremediation of simulated crude oil pollution in different sampling sites in the South China Sea. The metabolic pathways of ZS1 to degrade crude oil, the temporal dynamics of the microbial community response to crude oil contamination, and the biofortification process were investigated. The results showed that the abundance and diversity of the microbial community decreased sharply after the occurrence of crude oil contamination. The best degradation rate of crude oil, which was achieved in the samples from the sampling site N3 after the addition of ZS1 bacteria, was 50.94% at 50 days. C13 alkanes were totally oxidized by ZS1 in the 50 days. The degradation rate of solid n-alkanes (C18-C20) was about 70%. Based on the whole genome sequencing and the metabolites analysis of ZS1, we found that ZS1 degraded n-alkanes through the terminal oxidation pathway and aromatic compounds through the catechol pathway. This study provides data support for further research on biodegradation pathways of crude oil and contributes to the subsequent development of more reasonable bioremediation strategies.

Baseline study of water, soil, and identification of potential native phytoremediators of total petroleum hydrocarbon from oil-contaminated areas in the vicinity of Geleky oilfield of Assam.

Petrochemical contamination has been one of the significant causes of pollution all over the world. The upper Assam of Northeast India has been known for its oil industries and their contribution to India's economy. With tremendous oil production, an adequate amount of petroleum contamination is also observed. Several works have been furnished in the oilfields of Assam; however, the knowledge of heavy metal contamination and hydrocarbon pollution in nearby water bodies and soil, along with risk assessment and statistical validation in the vicinity of the Geleky oilfield of Sibsagar district of Assam, is still limited. The study also reveals native potential phytoremediators that can uptake heavy metals and hydrocarbons to help clean the environment through a greener approach. The presence of aromatic hydrocarbon derivatives in water, soil, plants, and sludge samples, including groundwater, is an alarming concern due to their high toxicity to the surrounding ecosystem and potential threat to the groundwater system. The Principal Component Analysis (PCA) further corroborates the significant and common origin of the heavy metals and total petroleum hydrocarbon (TPH), which inclines toward the oil exploration activities in the nearby oilfield. Among all the six plant species studied, Colocasia esculenta proved to be a noteworthy phytoremediator of both heavy metals and TPH, having an uptake efficiency of 78% of Zn, 46% of Pb, and 75% of Fe, and 70% of TPH. The study provides baseline information to help us identify future threats and suitable endemic phytoremediators, which can be advantageous for future remediation.

Enhancement of oil forensic methodology through the addition of polycyclic aromatic nitrogen heterocycle biomarkers for diagnostic ratios.

Current oil spill forensic identification of source oils relies upon hydrocarbon biomarkers resistant to weathering. This international technique was developed by the European Committee for Standardization (CEN), under EN 15522-2 Oil Spill Identification guidelines. The number of biomarkers have expanded at pace with technological advances, while distinguishing new biomarkers becomes more challenging due to interference of isobaric compounds, matrix effects, and high cost of weathering experiments. Application of high-resolution mass spectrometry enabled exploration of potential polycyclic aromatic nitrogen heterocycle (PANH) oil biomarkers. The instrumentation showed reduction in isobaric and matrix interferences, allowing for identification of low-level PANH and alkylated PANHs (APANHs). Weathered oil samples, obtained from a marine microcosm weathering experiment, enabled comparison with source oils to identify new, stable forensic biomarkers. This study highlighted eight new APANH diagnostic ratios that expanded the biomarker suite, increasing the confidence for identifying highly weathered oils back to their source oil.

Metagenomic and Metatranscriptomic Responses of Chemical Dispersant Application during a Marine Dilbit Spill.

The global increase in marine transportation of dilbit (diluted bitumen) can increase the risk of spills, and the application of chemical dispersants remains a common response practice in spill events. To reliably evaluate dispersant effects on dilbit biodegradation over time, we set large-scale (1,500 mL) microcosms without nutrient addition using a low dilbit concentration (30 ppm). Shotgun metagenomics and metatranscriptomics were deployed to investigate microbial community responses to naturally and chemically dispersed dilbit. We found that the large-scale microcosms could produce more reproducible community trajectories than small-scale (250 mL) ones based on the 16S rRNA gene amplicon sequencing. In the early-stage large-scale microcosms, multiple genera were involved in the biodegradation of dilbit, while dispersant addition enriched primarily Alteromonas and competed for the utilization of dilbit, causing depressed degradation of aromatics. The metatranscriptomic-based metagenome-assembled genomes (MAG) further elucidated early-stage microbial antioxidation mechanism, which showed that dispersant addition triggered the increased expression of the antioxidation process genes of Alteromonas species. Differently, in the late stage, the microbial communities showed high diversity and richness and similar compositions and metabolic functions regardless of dispersant addition, indicating that the biotransformation of remaining compounds can occur within the post-oil communities. These findings can guide future microcosm studies and the application of chemical dispersants for responding to a marine dilbit spill. IMPORTANCE In this study, we employed microcosms to study the effects of marine dilbit spill and dispersant application on microbial community dynamics over time. We evaluated the impacts of microcosm scale and found that increasing the scale is beneficial for reducing community stochasticity, especially in the late stage of biodegradation. We observed that dispersant application suppressed aromatics biodegradation in the early stage (6 days), whereas exerting insignificant effects in the late stage (50 days), from both substance removal and metagenomic/metatranscriptomic perspectives. We further found that Alteromonas species are vital for the early-stage chemically dispersed oil biodegradation and clarified their degradation and antioxidation mechanisms. These findings help us to better understand microcosm studies and microbial roles for biodegrading dilbit and chemically dispersed dilbit and suggest that dispersant evaluation in large-scale systems and even through field trails would be more realistic after marine oil spill response.

Carboxylate Group-Based Phase-Selective Organogelators with a pH-Triggered Recyclable Property.

Phase-selective organogelators (PSOGs) have recently attracted more attention because of their advantages in handling oil spills and leaked organic solvents. However, it is difficult to separate and recover the organic phase and PSOGs from organic gels due to the strong interaction between them. Aiming to enhance the separation and recovery performance of the organic phase and PSOGs, we synthesized a series of pH-responsive PSOGs by using itaconic anhydride and fatty amines with carbon chain lengths of C12-C18. Here, PSOGs have an excellent gelation ability in that amounts of organic solvents and fuel oil can be solidified at a low concentration (<3 wt %). It is worth noting that these gels are stronger, which is more convenient for removal by a salvage operation. More importantly, compared with traditional organogelators, pH-responsive PSOGs can easily recover the organic phase and fuel oil with an adjustment of the pH without extraction or distillation. Because of the transformation between the hydrophilicity and hydrophobicity of PSOGs by pH stimulation, 83.15% PSOGs are recovered in three-cycle experiments. In addition, the recycled PSOGs can be used to realize the removal of the organic phase again. Herein, we find that pH-responsive PSOGs could be used as promising and sustainable materials for separating and recovering organic solvents/oils and PSOGs.

Pattern recognition analysis of marine oil spills in airborne passive infrared multispectral remote sensing images.

Pattern recognition methodology was developed for the automated detection of marine oil spills in passive infrared multispectral remote sensing images. The images employed in this work were collected from the Deepwater Horizon oil spill accident in 2010. The imaging instrument for data collection was a downward-looking infrared line scanner equipped with eight optical bandpass filters in the spectral range of 8-12 µm on a fixed-wing aircraft. Oil slicks may show either positive or negative thermal contrast against the surrounding sea water, depending on the sun glint conditions or the oil thickness. Classifiers were developed separately to detect oil with different contrasts by the application of backpropagation neural networks to the preprocessed radiances. Preprocessing strategies included: (1) assembly of training data through k-means clustering analysis; (2) elimination of variation in radiance magnitudes by a customized temperature correction method; (3) removal of sun glint artifacts in images by polynomial correction; and (4) extraction of the most representative features as inputs for the neural networks by a subset selection approach. The classifiers designed to detect oil with positive and negative thermal contrast relative to water achieved overall classification accuracies of 88.7 and 92.2%, respectively. Composite classification images were generated by integrating classification scores produced by the two classifiers. The prediction performance of the classification system was demonstrated through its application to images not involved during the training of the networks.

Oil-Water Separation Polypropylene Foam with Advanced Solvent-Evaporation Induced Coexistence of Microspheres and Microporous Structure.

For decades, crude oil spills and oil wastewater have become the most problematic environmental pollution and damage to public health. Therefore, it is considerable to develop superhydrophobic polymer foam for separating oil from water with high selectivity and sorption capacity. Here, a new type of environmentally friendly pure polypropylene (PP) foam with superhydrophobicity is first time proposed with a particular coexistence of microspheres and microporous structure fabricated via an advanced solvent-evaporation method. The PP foam exhibits exceptional superhydrophobic with a water contact angle of 151° and the maximum saturated adsorption capacity of 26 g g-1 . After more than 15 h of cyclic continuous oil-water pumping experiment, it still maintains a high oil absorption efficiency of 98%, providing the basis for practical commercial applications. More importantly, the variation of hydrophobic properties is described by Flory-Huggins polymer solution theory and Huggins interaction parameters, and the optimal solution ratio range is predicted which provides a relevant theoretical basis for actual industrial production.

Cleanup of oiled shorelines using a dual responsive nanoclay/sodium alginate surface washing agent.

Oil spills may affect ecosystems and endanger public health. In this study, we developed a novel and dual responsive nanoclay/sodium alginate (NS) washing fluid, and systematically evaluated its application potential in oiled shoreline cleanup. The characterization results demonstrated that sodium alginate combined with nanoclay via hydrogen bonds, and was inserted into the interlayer spacing of nanoclay. Adding sodium alginate reduced surface and interfacial tensions, while increasing the viscoelasticity of the washing fluid. Batch experiments were conducted to investigate oil removal performance under various conditions. Additionally, the factorial design analysis showed that three single factors (temperature, oil concentration, and salinity), and two interactive effects (temperature/salinity; and oil concentration/HA) displayed significant effects on the oil removal efficiency of the NS washing fluid. Compared to the commercial surfactants, the NS composite exhibited satisfactory removal efficiencies for treating oily sand. Green materials-stabilized Pickering emulsion can potentially be used for oil/water separation. The NS washing agent displayed excellent pH- and Ca2+- responsiveness, generating transparent supernatants with low oil concentration and turbidity. Our work opens an interesting avenue for designing economical, high performance, and green washing agents.

Identification of bilge oil with lubricant: Recent oil spill case studies.

Oil spills have many adverse effects on the marine environment. Bilge oil spills occur frequently in the sea as a result of maritime accidents or illegal discharge. It is difficult to unambiguously identify the specific sources of such spills because bilge oil contains a mixture of fuel oil and lubricant. In this study, bilge oils with different fuel oil/lubricant ratios were prepared and analyzed using a modified version of the CEN/TR methodology (European Committee for Standardization, 2012). As the lubricant content of bilge oil increased, the intensity of the C20-C24 group, which is the commonly-used normalization compound group for fuel oil in the percentage weathering (PW) plot, also changed. Therefore, the mean area of the C15-C18 group, which was affected by the lubricant content, was used instead. Although heavy fuel oil is usually normalized to a hopane, bilge oil with a high lubricant content cannot be analyzed based on a mass spectrometry (MS)-PW plot; thus, heavy fuel oil-based bilge oil was normalized to a phytane in this study. Although hopanes and styrenes are unsuitable comparison compounds for heavy fuel oil-based bilge oil analysis, for light fuel oil-based bilge oil, hopanes and steranes could be applied as diagnostic ratio comparisons when the lubricant peak was clearly detected in the chromatograms of the spilled and suspected oil samples. By applying the CEN/TR methodology according to this approach, the similarities between spilled and suspected oil samples were more easily revealed. In addition, the field applicability of the proposed method was tested for four actual oil spills.

Offshore field experiments with in-situ burning of oil: Emissions and burn efficiency.

In situ burning (ISB) is an oil spill response technique including ignition and burning to remove oil on the water surface. The technique rapidly and effectively removes large portions of the oil. However, the combustion process causes a large smoke plume and leaves a viscous residue in the water. During six large-scale experimental burns in the North Sea in 2018 and 2019, the smoke plume, released oil and contained residues were analysed. The objectives were to document the content of particles and gases in the smoke plume, properties of both the released oils and residues, and the effectiveness of the burns. Oseberg crude oil, Ultra Low Sulphur Fuel Oil (ULSFO), Intermediate Fuel Oil (IFO180) and Marine Gas Oil (MGO) were released into a fire-boom and ignited. Particles and gases in the smoke plume were monitored using drones with several sensors. Soot particle monitoring indicated that more than 90% of the particles produced during the burns were <1 µm. Soot fallout was mainly limited to visible smoke, and the particle concentration was highest directly under the smoke plume and declined with distance from the burn. Gas monitoring in the smoke indicated low concentrations of SO2 and NOX (<2 ppm), and the concentrations of CO2 and CO were within air quality standards. Black Carbon produced relative to the amount of oil burned was 10-18%. The burn efficiency varied and were estimated to 80-91% for Oseberg, >90% for MGO, and <60% for both ULSFO and IFO180. The present paper addresses the results of the smoke plume monitoring, properties of the ISB residues and the burn efficiency.