Evaluating workplace protection factors (WPFs) of different firefighter PPE interface control measures for select volatile organic compounds (VOCs).

Structural firefighters are exposed to a complex set of contaminants and combustion byproducts, including volatile organic compounds (VOCs). Additionally, recent studies have found structural firefighters' skin may be exposed to multiple chemical compounds via permeation or penetration of chemical byproducts through or around personal protective equipment (PPE). This mannequin-based study evaluated the effectiveness of four different PPE conditions with varying contamination control measures (incorporating PPE interface design features and particulate blocking materials) to protect against ingress of several VOCs in a smoke exposure chamber. We also investigated the effectiveness of long-sleeve base layer clothing to provide additional protection against skin contamination. Outside gear air concentrations were measured from within the smoke exposure chamber at the breathing zone, abdomen, and thigh heights. Personal air concentrations were collected from mannequins under PPE at the same general heights and under the base layer at abdomen and thigh heights. Sampled contaminants included benzene, toluene, styrene, and naphthalene. Results suggest that VOCs can readily penetrate the ensembles. Workplace protection factors (WPFs) were near one for benzene and toluene and increased with increasing molecular weight of the contaminants. WPFs were generally lower under hoods and jackets compared to under pants. For all PPE conditions, the pants appeared to provide the greatest overall protection against ingress of VOCs, but this may be due in part to the lower air concentrations toward the floor (and cuffs of pants) relative to the thigh-height outside gear concentrations used in calculating the WPFs. Providing added interface control measures and adding particulate-blocking materials appeared to provide a protective benefit against less-volatile chemicals, like naphthalene and styrene.

Effect of ionic strength on the assembly of simian vacuolating virus capsid protein around poly(styrene sulfonate).

Virus-like particles (VLPs) are noninfectious nanocapsules that can be used for drug delivery or vaccine applications. VLPs can be assembled from virus capsid proteins around a condensing agent, such as RNA, DNA, or a charged polymer. Electrostatic interactions play an important role in the assembly reaction. VLPs assemble from many copies of capsid protein, with a combinatorial number of intermediates. Hence, the mechanism of the reaction is poorly understood. In this paper, we combined solution small-angle X-ray scattering (SAXS), cryo-transmission electron microscopy (TEM), and computational modeling to determine the effect of ionic strength on the assembly of Simian Vacuolating Virus 40 (SV40)-like particles. We mixed poly(styrene sulfonate) with SV40 capsid protein pentamers at different ionic strengths. We then characterized the assembly product by SAXS and cryo-TEM. To analyze the data, we performed Langevin dynamics simulations using a coarse-grained model that revealed incomplete, asymmetric VLP structures consistent with the experimental data. We found that close to physiological ionic strength, [Formula: see text] VLPs coexisted with VP1 pentamers. At lower or higher ionic strengths, incomplete particles coexisted with pentamers and [Formula: see text] particles. Including the simulated structures was essential to explain the SAXS data in a manner that is consistent with the cryo-TEM images.

A review of extraction methods and analytical techniques for styrene and its metabolites in biological matrices.

We reviewed the toxicokinetics of styrene to introduce reliable surrogates for the biological monitoring of styrene workers. We have also discussed the extraction techniques and analytical methods of styrene and its metabolites. Sample preparation is the main bottleneck of the analytical techniques for styrene and its metabolites. Although some microextraction methods have been developed to overcome such disadvantages, some still have limitations such as long extraction time, fiber swelling and breakage, and the cost and the limited lifetime of the fiber. Among all, microextraction by packed sorbents, coupled with HPLC with ultraviolet detection (MEPS-HPLC-UV), can be the method of choice for determining styrene metabolites. Few studies investigated unchanged styrene in breath samples. Chemical determination of styrene in exhaled breath provides new insights into organ toxicity in workers with inhalation exposures and can be considered a fascinating tool in risk assessment strategies. Taking blood samples is invasive and less accepted by workers. In contrast, breath analysis is the most attractive method for workers because breath samples are easy to collect and non-invasive, and sample collection does not require the transfer of workers to health facilities. Therefore, developing selective and sensitive methods for determining styrene in breath samples is recommended for future studies.

Evaluation of Pulmonary Effects of 3-D Printer Emissions From Acrylonitrile Butadiene Styrene Using an Air-Liquid Interface Model of Primary Normal Human-Derived Bronchial Epithelial Cells.

This study investigated the inhalation toxicity of the emissions from 3-D printing with acrylonitrile butadiene styrene (ABS) filament using an air-liquid interface (ALI) in vitro model. Primary normal human-derived bronchial epithelial cells (NHBEs) were exposed to ABS filament emissions in an ALI for 4 hours. The mean and mode diameters of ABS emitted particles in the medium were 175 ± 24 and 153 ± 15 nm, respectively. The average particle deposition per surface area of the epithelium was 2.29 × 107 ± 1.47 × 107 particle/cm2, equivalent to an estimated average particle mass of 0.144 ± 0.042 µg/cm2. Results showed exposure of NHBEs to ABS emissions did not significantly affect epithelium integrity, ciliation, mucus production, nor induce cytotoxicity. At 24 hours after the exposure, significant increases in the pro-inflammatory markers IL-12p70, IL-13, IL-15, IFN-γ, TNF-α, IL-17A, VEGF, MCP-1, and MIP-1α were noted in the basolateral cell culture medium of ABS-exposed cells compared to non-exposed chamber control cells. Results obtained from this study correspond with those from our previous in vivo studies, indicating that the increase in inflammatory mediators occur without associated membrane damage. The combination of the exposure chamber and the ALI-based model is promising for assessing 3-D printer emission-induced toxicity.

Emission Profiles of Volatiles during 3D Printing with ABS, ASA, Nylon, and PETG Polymer Filaments.

In this short communication we characterize the emission of volatile organic compounds (VOCs) from fused filament fabrication (FFF) 3D printing using four polymer materials, namely polyethylene terephthalate glycol-modified (PETG), acrylonitrile styrene acrylate (ASA), Nylon, and acrylonitrile butadiene styrene (ABS). Detailed emission profiles are obtained during thermal degradation of the polymers as a function of temperature and also in real-time during 3D printing. Direct quantitative measurement was performed using proton transfer reaction time-of-flight mass spectrometry (PTR-ToF-MS). Qualitative determination of the volatiles emitted from the printed elements at various temperatures was accomplished using gas chromatography-mass spectrometry (GC-MS). The emission rates of VOCs differ significantly between the different polymer filaments, with the emission from Nylon and PETG more than an order of magnitude lower than that of ABS.

Associations of Occupational Styrene Exposure With Risk of Encephalopathy and Unspecified Dementia: A Long-Term Follow-up Study of Workers in the Reinforced Plastics Industry.

Exposure to industrial solvents has been associated with encephalopathy. Styrene is a neurotoxic industrial solvent, and we investigated the long-term risk of encephalopathy and unspecified dementia following styrene exposure. We followed 72,465 workers in the reinforced plastics industry in Denmark (1977-2011) and identified incident cases of encephalopathy (n = 228) and unspecified dementia (n = 565) in national registers. Individual styrene exposure levels were modeled from information on occupation, measurements of work place styrene levels, product, process, and years of employment. Adjusted analyses were performed using a discrete survival function. A positive trend for encephalopathy (P < 0.01) and a negative trend for unspecified dementia (P = 0.03) were seen with cumulative styrene exposure accrued during the recent period of up to 15 years. For unspecified dementia and the combination of unspecified dementia and encephalopathy, a positive trend was indicated when applying a 30-year exposure lag (P = 0.13 and P = 0.07). The risk patterns seen following recent exposure probably reflect diagnostic criteria for encephalopathy requiring recent industrial solvent exposure and referral bias rather than association with styrene exposure, while the increasing risk observed for unspecified dementia and the combination of encephalopathy and unspecified dementia following distant exposure indicates an increased risk of dementia following styrene exposure with a long latency period.

The genotoxicity of an organic solvent mixture: A human biomonitoring study and translation of a real-scenario exposure to in vitro.

This study aimed to evaluate occupational exposure to a styrene and xylene mixture through environmental exposure assessment and identify the potential genotoxic effects through biological monitoring. Secondly, we also exposed human peripheral blood cells in vitro to both xylene and styrene either alone or in mixture at concentrations found in occupational settings in order to understand their mechanism of action. The results obtained by air monitoring were below the occupational exposure limits for both substances. All biomarkers of effect, except for nucleoplasmic bridges, had higher mean values in workers (N = 17) compared to the corresponding controls (N = 17). There were statistically significant associations between exposed individuals and the presence of nuclear buds and oxidative damage. As for in vitro results, there was no significant influence on primary DNA damage in blood cells as evaluated by the comet assay. On the contrary, we did observe a significant increase of micronuclei and nuclear buds, but not nucleoplasmic bridges upon in vitro exposure. Taken together, both styrene and xylene have the potential to induce genomic instability either alone or in combination, showing higher effects when combined. The obtained data suggested that thresholds for individual chemicals might be insufficient for ensuring the protection of human health.

Reactive and Additive Modifications of Styrenic Polymers with Phosphorus-Containing Compounds and Their Effects on Fire Retardance.

Polystyrene, despite its high flammability, is widely used as a thermal insulation material for buildings, for food packaging, in electrical and automotive industries, etc. A number of modification routes have been explored to improve the fire retardance and boost the thermal stability of commercially important styrene-based polymeric products. The earlier strategies mostly involved the use of halogenated fire retardants. Nowadays, these compounds are considered to be persistent pollutants that are hazardous to public and environmental health. Many well-known halogen-based fire retardants, regardless of their chemical structures and modes of action, have been withdrawn from built environments in the European Union, USA, and Canada. This had triggered a growing research interest in, and an industrial demand for, halogen-free alternatives, which not only will reduce the flammability but also address toxicity and bioaccumulation issues. Among the possible options, phosphorus-containing compounds have received greater attention due to their excellent fire-retarding efficiencies and environmentally friendly attributes. Numerous reports were also published on reactive and additive modifications of polystyrene in different forms, particularly in the last decade; hence, the current article aims to provide a critical review of these publications. The authors mainly intend to focus on the chemistries of phosphorous compounds, with the P atom being in different chemical environments, used either as reactive, or additive, fire retardants in styrene-based materials. The chemical pathways and possible mechanisms behind the fire retardance are discussed in this review.

Occupational exposure to styrene and its relation with urine mandelic acid, in plastic injection workers.

Plastic injection industry workers are exposed to toxic gases and vapors, including styrene. This study aimed to measure exposure to styrene and its relation with urine mandelic acid among plastics injection workers of the electrical parts industry. This descriptive and analytical cross-sectional study was carried out in the plastic injection halls of the electronics industry, in winter 2017 and spring 2018. Styrene gas in the workers' respiratory region was sampled by the NIOSH 1501 method and was analyzed by gas chromatography-mass spectrometry (GC/MAS). Mandelic acid concentration was determined by high-performance liquid chromatography (HPLC). Statistical data analysis was performed with STATA11. The mean of age and working experience in the population under study were 32.4 ± 8.1 and 6.4 ± 5 years, respectively. The average exposure to styrene was 83.2 ± 32.4 mg·m-3 and the mean of urine mandelic acid was 1570.1 ± 720.6 mg·g ceratinine-1. There were 24 workers (45.3%) exposed to levels above permissible limits recommended by national and international organizations. There was a positive and significant correlation between exposure to styrene and urine mandelic acid (P = 0.006, r = 0.4). In multivariate regression, occupational exposure to styrene (P = 0.002, ß = 0.5) was the strongest variable, predicting the amount of urine mandelic acid. Increased occupational exposure to styrene increases mandelic acid in the urine, and applying control measures to reduce exposure to styrene vapor is recommended in high exposure situations.

Characterization of chemical contaminants generated by a desktop fused deposition modeling 3-dimensional Printer.

Printing devices are known to emit chemicals into the indoor atmosphere. Understanding factors that influence release of chemical contaminants from printers is necessary to develop effective exposure assessment and control strategies. In this study, a desktop fused deposition modeling (FDM) 3-dimensional (3-D) printer using acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) filaments and two monochrome laser printers were evaluated in a 0.5 m3 chamber. During printing, chamber air was monitored for vapors using a real-time photoionization detector (results expressed as isobutylene equivalents) to measure total volatile organic compound (TVOC) concentrations, evacuated canisters to identify specific VOCs by off-line gas chromatography-mass spectrometry (GC-MS) analysis, and liquid bubblers to identify carbonyl compounds by GC-MS. Airborne particles were collected on filters for off-line analysis using scanning electron microscopy with an energy dispersive x-ray detector to identify elemental constituents. For 3-D printing, TVOC emission rates were influenced by a printer malfunction, filament type, and to a lesser extent, by filament color; however, rates were not influenced by the number of printer nozzles used or the manufacturer's provided cover. TVOC emission rates were significantly lower for the 3-D printer (49-3552 µg h-1) compared to the laser printers (5782-7735 µg h-1). A total of 14 VOCs were identified during 3-D printing that were not present during laser printing. 3-D printed objects continued to off-gas styrene, indicating potential for continued exposure after the print job is completed. Carbonyl reaction products were likely formed from emissions of the 3-D printer, including 4-oxopentanal. Ultrafine particles generated by the 3-D printer using ABS and a laser printer contained chromium. Consideration of the factors that influenced the release of chemical contaminants (including known and suspected asthmagens such as styrene and 4-oxopentanal) from a FDM 3-D printer should be made when designing exposure assessment and control strategies.

Biodegradation of airborne acetone/styrene mixtures in a bubble column reactor.

The ability of a bubble column reactor (BCR) to biodegrade a mixture of styrene and acetone vapors was evaluated to determine the factors limiting the process efficiency, with a particular emphasis on the presence of degradation intermediates and oxygen levels. The results obtained under varied loadings and ratios were matched with the dissolved oxygen levels and kinetics of oxygen mass transfer, which was assessed by determination of kLa coefficients. A 1.5-L laboratory-scale BCR was operated under a constant air flow of 1.0 L.min-1, using a defined mixed microbial population as a biocatalyst. Maximum values of elimination capacities/maximum overall specific degradation rates of 75.5 gC.m-3.h-1/0.197 gC.gdw-1.h-1, 66.0 gC.m-3.h-1/0.059 gC.gdw-1.h-1, and 45.8 gC.m-3.h-1/0.027 gC.gdw-1.h-1 were observed for styrene/acetone 2:1, styrene-rich and acetone-rich mixtures, respectively, indicating significant substrate interactions and rate limitation by biological factors. The BCR removed both acetone and styrene near-quantitatively up to a relatively high organic load of 50 g.m-3.h-1. From this point, the removal efficiencies declined under increasing loading rates, accompanied by a significant drop in the dissolved oxygen concentration, showing a process transition to oxygen-limited conditions. However, the relatively efficient pollutant removal from air continued, due to significant oxygen mass transfer, up to a threshold loading rate when the accumulation of acetone and degradation intermediates in the aqueous medium became significant. These observations demonstrate that oxygen availability is the limiting factor for efficient pollutant degradation and that accumulation of intermediates may serve as an indicator of oxygen limitation. Microbial (activated sludge) analyses revealed the presence of amoebae and active nematodes that were not affected by variations in operational conditions.

Identification of signature volatiles to discriminate Candida albicans, glabrata, krusei and tropicalis using gas chromatography and mass spectrometry.

Oral candidiasis is the most frequent fungal infection of the oral cavity. Clinical diagnoses require mycological confirmation, which is time-consuming in case of culture testing. The aim of the study was to identify signature volatiles to develop a chairside breath test to diagnose oral candidiasis. Headspaces above Candida albicans, glabrata, tropicalis, krusei cultures, and growth media as control were analysed after eight and 24 h using offline gas chromatography and mass spectrometry. The identification of signature volatiles was assisted using various microbial databases. Retrieved volatile patterns enabled Candida species discrimination in vitro. For C. albicans 3-methyl-2-butanone and styrene and for C. krusei a combination of p-xylene, 2-octanone, 2-heptanone and n-butyl acetate were found to be specific. 1-hexanol was found in C. tropicalis, but is emitted by a variety of other microorganisms. C. glabrata was characterised through the absence of these volatiles. The development of a breath test is a promising approach in confirming suspicions of oral candidiasis. To confirm the retrieved results in vivo, breath tests in affected and healthy subjects have to be performed.

Characterization of emissions from a desktop 3D printer and indoor air measurements in office settings.

Emissions from a desktop 3D printer based on fused deposition modeling (FDM) technology were measured in a test chamber and indoor air was monitored in office settings. Ultrafine aerosol (UFA) emissions were higher while printing a standard object with polylactic acid (PLA) than with acrylonitrile butadiene styrene (ABS) polymer (2.1 × 10(9) vs. 2.4 × 10(8) particles/min). Prolonged use of the printer led to higher emission rates (factor 2 with PLA and 4 with ABS, measured after seven months of occasional use). UFA consisted mainly of volatile droplets, and some small (100-300 nm diameter) iron containing and soot-like particles were found. Emissions of inhalable and respirable dust were below the limit of detection (LOD) when measured gravimetrically, and only slightly higher than background when measured with an aerosol spectrometer. Emissions of volatile organic compounds (VOC) were in the range of 10 µg/min. Styrene accounted for more than 50% of total VOC emitted when printing with ABS; for PLA, methyl methacrylate (MMA, 37% of TVOC) was detected as the predominant compound. Two polycyclic aromatic hydrocarbons (PAH), fluoranthene and pyrene, were observed in very low amounts. All other analyzed PAH, as well as inorganic gases and metal emissions except iron (Fe) and zinc (Zn), were below the LOD or did not differ from background without printing. A single 3D print (165 min) in a large, well-ventilated office did not significantly increase the UFA and VOC concentrations, whereas these were readily detectable in a small, unventilated room, with UFA concentrations increasing by 2,000 particles/cm(3) and MMA reaching a peak of 21 µg/m(3) and still being detectable in the room even 20 hr after printing.

Development of a multi-VOC reference material for quality assurance in materials emission testing.

Emission test chamber measurement is necessary to proof building materials as sources of volatile organic compounds (VOCs). The results of such measurements are used to evaluate materials and label them according to their potential to emit harmful substances, polluting indoor air. If only labelled materials were installed indoors, this would improve indoor air quality and prevent negative impacts on human health. Because of the complex testing procedure, reference materials for the quality assurance are mandatory. Currently, there is a lack of such materials because most building products show a broad variation of emissions even within one batch. A previous study indicates lacquers, mixed with volatile organic pollutants, as reproducible emission source for a wide range of substances. In the present study, the curing of the lacquer-VOC mixture inside micro-chambers was optimised. Therefore, the humidity and the chamber flow were varied. Typical indoor air pollutants with a wide range of volatilities, for example, styrene, n-hexadecane, dimethyl and dibutyl phthalate were selected. It turned out that, under optimised curing parameters inside the micro-chamber, their emission can be reproduced with variations of less than 10 %. With this, a next important step towards a reference material for emission testing was achieved.

Biomonitoring for Exposure Assessment to Styrene in the Fibreglass Reinforced Plastic Industry: Determinants and Interferents.

Fifty-eight workers exposed to styrene were monitored in four fibreglass reinforced plastic industries of Central Italy. The aim of the study was to explore the factors that can influence the levels of styrene exposure biomarkers of the workers and the aspects that might interfere with the exposure assessment measures, such as the co-exposure to acetone. Personal monitoring of professional exposure to airborne styrene and acetone was carried out by Radiello samplers and GC/MS analysis. Biological monitoring was performed by the determination of urinary metabolites, mandelic (MA), and phenylglyoxylic (PGA) acids with HPLC/MS/MS and unmetabolized styrene in saliva and venous blood by HS/GC/MS. The median values of the four sites ranged between 24.1 to 94.0mg m(-3) and 7.3 to 331.1mg g(-1) creatinine for airborne styrene and MA + PGA, respectively. A good linear correlation was found between styrene in air and its urinary metabolites (r = 0.854). The median value for airborne styrene was found to exceed the (Threshold Limit Value - Time Weighted Average) of 85 mg m(-3) in one site for all the workers and in two if only moulders are considered. The multiple linear regression model showed that the determinants of urinary MA + PGA excretion were the type of process, workers' tasks, level of acetone co-exposure, and the use of respiratory protection devices. Data show that the simultaneous exposure to acetone modify the styrene metabolism with a reduction in the levels of (MA + PGA) excreted. A significant linear log-correlation was found between salivary levels of styrene and blood concentration (r = 0.746) sampled at the same t x time.

Characterisation of recycled acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment in Brazil.

Polymeric materials constitute a considerable fraction of waste computer equipment and polymers acrylonitrile-butadiene-styrene and high-impact polystyrene are the main thermoplastic polymeric components found in waste computer equipment. Identification, separation and characterisation of additives present in acrylonitrile-butadiene-styrene and high-impact polystyrene are fundamental procedures to mechanical recycling of these polymers. The aim of this study was to evaluate the methods for identification of acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment in Brazil, as well as their potential for mechanical recycling. The imprecise utilisation of symbols for identification of the polymers and the presence of additives containing toxic elements in determinate computer devices are some of the difficulties found for recycling of acrylonitrile-butadiene-styrene and high-impact polystyrene from waste computer equipment. However, the considerable performance of mechanical properties of the recycled acrylonitrile-butadiene-styrene and high-impact polystyrene when compared with the virgin materials confirms the potential for mechanical recycling of these polymers.

Stormwater chemical contamination caused by cured-in-place pipe (CIPP) infrastructure rehabilitation activities.

Cured-in-place pipe (CIPP) is becoming a popular U.S. stormwater culvert rehabilitation method. Several State transportation agencies have reported that CIPP activities can release styrene into stormwater, but no other contaminants have been monitored. CIPP's stormwater contamination potential and that of its condensate waste was characterized. Condensate completely dissolved Daphnia magna within 24 h. Condensate pH was 6.2 and its chemical oxygen demand (COD) level was 36,000 ppm. D. magna mortality (100%) occurred in 48 h, even when condensate was diluted by a factor of 10,000 and styrene was present at a magnitude less than its LC50. Condensate and stormwater contained numerous carcinogenic solvents used in resin synthesis, endocrine disrupting contaminants such as plasticizers, and initiator degradation products. For 35 days, COD levels at the culvert outlets and downstream ranged from 100 to 375 ppm and styrene was 0.01 to 7.4 ppm. Although contaminant levels generally reduced with time, styrene levels were greatest 50 ft downstream, not at the culvert outlet. Cured CIPP extraction tests confirmed that numerous contaminants other than styrene were released into the environment and their persistence and toxicity should be investigated. More effective contaminant containment and cleaner installation processes must be developed to protect the environment.

Surgical smoke may be a biohazard to surgeons performing laparoscopic surgery.

BACKGROUND: Surgical smoke production is inevitable during surgical procedures. Although many workplaces have adopted smoke-free environments, healthcare workers, especially surgeons, continue to be exposed to surgical smoke. METHODS: From February 2013 to March 2013, a total of 20 patients underwent transperitoneal laparoscopic nephrectomy for renal cell carcinoma. A 5-L gas sample was collected 30 min after the electrocautery device was first used and was analyzed by gas chromatography and mass spectrometry. Cancer risk was calculated for carcinogenic compounds and hazard quotient was calculated for noncarcinogenic compounds using US Environmental Protection Agency guidelines. RESULTS: Twenty patients with a median age of 57.5 years were enrolled in the study. Eighteen volatile organic compounds were detected by Japanese indoor air standards mix analysis. The cancer risks were ethanol, 5.10 × 10(-5) ± 6.35 × 10(-5); 1,2-dichloroethane, 4.75 × 10(-3) ± 7.42 × 10(-4); benzene, 1.09 × 10(-3) ± 4.33 × 10(-4); ethylbenzene, 2.87 × 10(-5) ± 1.32 × 10(-5); and styrene, 2.94 × 10(-6) ± 1.16 × 10(-6). The hazard quotients were acetone, 1.88 × 10(-2) ± 7.63 × 10(-3); hexane, 1.48 × 10(-1) ± 8.70 × 10(-2); benzene, 4.66 ± 1.85; toluene, 2.61 × 10(-2) ± 7.23 × 10(-3); p-xylene, 1.81 × 10(-1) ± 6.45 × 10(-2); o-xylene, 2.40 × 10(-2) ± 3.33 × 10(-2); and styrene, 5.15 × 10(-3) ± 2.03 × 10(-3). CONCLUSIONS: For five carcinogenic compounds detected, the cancer risk was greater than negligible. For 1,2-dichloroethane and benzene, the risk was classified as unacceptable. Analysis of noncarcinogenic compounds showed that risk reduction measures are needed for benzene. Even though surgical smoke is not an immediate health hazard, operating room personnel should be aware of the potential long-term health risks associated with exposure.

Pollution characteristics and health risk assessment of benzene homologues in ambient air in the northeastern urban area of Beijing, China.

Ambient benzene homologues were measured at a site in the northeastern urban area of Beijing, China, from August 24 to September 4, 2012 by SUMMA canister sampling followed by laboratory determination using cryogenic cold trap pre-concentration-GC-MS/FID, and their health risks were also assessed. Daily total benzene homologues ranged from 0.99 to 49.71 microg/m3 with an average of 11.98 microg/m3. Benzene homologues showed higher concentrations in the morning and evening than that at noontime. Comparison with previous studies revealed a trend of decrease for ambient benzene homologues probably due to the effective emission control in Beijing in recent years. Vehicular exhaust was the main source while volatilization of paints and solvents also made substantial contributions. Health risk assessment showed that BTEX (benzene, toluene, ethylbenzene, o-xylene, m-xylene and p-xylene) and styrene had no appreciable adverse non-cancer health risks for the exposed population, while benzene has potential cancer risk of 1.34E-05. Available data from cities in China all implied that benzene imposes relatively higher cancer risk on the exposed populations and therefore strict control measures should be taken to further lower ambient benzene levels in China.

Co-exposure of petrochemical workers to noise and mixture of benzene, toluene, ethylbenzene, xylene, and styrene: Impact on mild renal impairment and interaction.

Epidemiological evidence concerning effects of simultaneous exposure to noise and benzene, toluene, ethylbenzene, xylene, and styrene (BTEXS) on renal function remains uncertain. In 2020, a cross-sectional study was conducted among 1160 petrochemical workers in southern China to investigate effects of their co-exposure on estimated glomerular filtration rate (eGFR) and mild renal impairment (MRI). Noise levels were assessed using cumulative noise exposure (CNE). Urinary biomarkers for BTEXS were quantified. We found the majority of workers had exposure levels to noise and BTEXS below China's occupational exposure limits. CNE, trans, trans-muconic acid (tt-MA), and the sum of mandelic acid and phenylglyoxylic acid (PGMA) were linearly associated with decreased eGFR and increased MRI risk. We observed U-shaped associations for both N-acetyl-S-phenyl-L-cysteine (SPMA) and o-methylhippuric acid (2-MHA) with MRI. In further assessing the joint effect of BTEXS (ß, -0.164 [95% CI, -0.296 to -0.033]) per quartile increase in all BTEXS metabolites on eGFR using quantile g-computation models, we found SPMA, tt-MA, 2-MHA, and PGMA played pivotal roles. Additionally, the risk of MRI associated with tt-MA was more pronounced in workers with lower CNE levels (P = 0.004). Multiplicative interaction analysis revealed antagonisms of CNE and PGMA on MRI risk (P = 0.034). Thus, our findings reveal negative dose-effect associations between noise and BTEXS mixture exposure and renal function in petrochemical workers. With the exception of toluene, benzene, xylene, ethylbenzene, and styrene are all concerning pollutants for renal dysfunction. Effects of benzene, ethylbenzene, and styrene exposure on renal dysfunction were more pronounced in workers with lower CNE.