Improved resin-to-dentin bond strength and durability via non-thermal atmospheric pressure plasma drying of etched dentin.

This study aimed to evaluate the improvement in strength and durability of the bond between dentin and composite resins following plasma drying of the etched dentin surface using non-thermal atmospheric pressure plasma. Plasma drying was applied to the etched dentin before applying adhesive. Conventional wet-bonding and helium (He) gas-dried bonding schemes were used as control groups. The bond strength of the composite resin to dentin was measured as the microtensile bond strength at 24 h after bonding and after 10,000 cycles of thermocycling. Hybrid layer formation was observed using micro-Raman spectroscopy and scanning electron microscopy. Although the bond-strength values were not statistically different either at 24 h after bonding or after thermocycling, the bond strength of the plasma-dried bonding group was significantly higher than the conventional wet-bonding group and He gas-dried bonding group. Micro-Raman spectral analysis revealed effective penetration of the adhesive and an improved polymerization rate of the adhesive after plasma drying. Plasma drying increased the penetration of hydrophobic resin into the collagen mesh structure, which improved mechanical bonding and long-term durability between dentin and composite resin.

Promotion of resin bonding to dental zirconia ceramic using plasma deposition of tetramethylsilane and benzene.

The aim of this study was to investigate the effects of plasma-enhanced deposition of an organosilane and benzene on resin bonding to a dental zirconia ceramic. A total of 70 zirconia specimens, which were polished before sintering, were randomly divided into five groups according to surface treatments before applying a dental adhesive (each group, n = 14): group 1, no previous treatment (control); group 2, plasma deposition with tetramethylsilane (TMS); group 3, plasma deposition with benzene; group 4, sequential plasma deposition with TMS and benzene; and group 5, a zirconia primer (Z-Prime Plus). A dental adhesive (Scotchbond Multi-Purpose adhesive) was applied to the surface-treated zirconia, and resin composite rods were built in to enable shear bond-strength testing. The sequential deposition of TMS and benzene showed the highest bond strength [22.7 ± 3.7 MPa (mean ± SD)], approximately twice that of Z-Prime Plus (10.3 ± 3.2 MPa). The plasma deposition with either TMS or benzene also significantly improved bond-strength values compared with the negative-control group, and their effects were not statistically different from that of Z-Prime Plus. Following plasma deposition with TMS, the introduction of silicon-oxygen-zirconium (Si-O-Zr) bonds on the zirconia surface was confirmed via X-ray photoelectron spectroscopy (XPS) analysis. Transmission electron microscopy and energy dispersive X-ray spectroscopy showed that a silica-like layer and a polymerizable carbon-rich layer were formed through sequential deposition with TMS and benzene.

Promotion of adhesive penetration and resin bond strength to dentin using non-thermal atmospheric pressure plasma.

Non-thermal atmospheric pressure plasmas (NT-APPs) have been shown to improve the bond strength of resin composites to demineralized dentin surfaces. Based on a wet-bonding philosophy, it is believed that a rewetting procedure is necessary after treatment with NT-APP because of its air-drying effect. This study investigated the effect of 'plasma-drying' on the bond strength of an etch-and-rinse adhesive to dentin by comparison with the wet-bonding technique. Dentin surfaces of human third molars were acid-etched and divided into four groups according to the adhesion procedure: wet bonding, plasma-drying, plasma-drying/rewetting, and dry bonding. In plasma treatment groups, the demineralized dentin surfaces were treated with a plasma plume generated using a pencil-type low-power plasma torch. After the adhesion procedures, resin composite/dentin-bonded specimens were subjected to a microtensile bond-strength test. The hybrid layer formation was characterized by micro-Raman spectroscopy and scanning electron microscopy. The plasma-drying group presented significantly higher bond strength than the wet-bonding and dry-bonding groups. Micro-Raman spectral analysis indicated that plasma-drying improved the penetration and polymerization efficacy of the adhesive. Plasma-drying could be a promising method to control the moisture of demineralized dentin surfaces and improve the penetration of adhesive and the mechanical property of the adhesive/dentin interface.

Influence of preparation design on fit and ceramic thickness of CEREC 3 partial ceramic crowns after cementation.

OBJECTIVE: This study investigated the influence of preparation design on the marginal and internal gap and ceramic thickness of partial ceramic crowns (PCCs) fabricated with the CEREC 3 system. MATERIALS AND METHODS: Sixteen extracted human mandibular molars were prepared according to two different preparation designs (n = 8): a retentive preparation design with traditional cusp capping (Group I) and a non-retentive preparation design with horizontal reduction of cusps (Group II). PCCs were fabricated from IPS Empress CAD with the CEREC 3 system. The parameters for luting space and minimum occlusal ceramic thickness were set to 30 µm and 1.5 mm, respectively. The fabricated PCCs were cemented to their corresponding teeth with self-adhesive resin cement and were then scanned by micro-computed tomography. The marginal and internal gaps were measured at pre-determined measuring points in five bucco-lingual and three mesio-distal cross-sectional images. The ceramic thicknesses of the PCCs were measured at the measuring points for cusp capping areas. RESULTS: Group II (167.4 ± 76.4 µm) had a smaller overall mean gap, which included the marginal and internal gap measurements, than that of Group I (184.8 ± 89.0 µm). The internal gaps were larger than the marginal gaps, regardless of preparation design. Group I presented a thinner ceramic thickness in the cusp capping areas than the minimum occlusal ceramic thickness parameter of 1.5 mm. CONCLUSION. Preparation design had an influence on fit, particularly the internal gap of the PCCs. Ceramic thickness could be thinner than the minimum ceramic thickness parameter.

Peri-implant bone formation of non-thermal atmospheric pressure plasma-treated zirconia implants with different surface roughness in rabbit tibiae.

OBJECTIVES: The aim of this study was to evaluate and compare the osseointegration of powder-injection molded (PIM) zirconia implants in rabbit tibiae with or without He plasma treatment. MATERIAL AND METHODS: Twenty-five rabbits received 4 types of external hex implants with identical geometry in the tibiae: PIM zirconia implants, roughened PIM zirconia implants, plasma-treated PIM zirconia implants, and plasma-treated roughened PIM zirconia implants. The contact angles of the four types of implants were evaluated. Removal torque tests and histomorphometric analyses were performed. RESULTS: The plasma treatment markedly enhanced the hydrophilicity, but did not seem to change the surface topography of the PIM zirconia implants. There were statistically significant differences in the bone-to-implant contact (BIC) ratios, bone volume (BV/TV), and removal torque values (RTQ) among the tested implant types (P < 0.001). The plasma-treated implants exhibited significantly higher BIC and BV/TV values than the untreated implants. However, the removal torque values favored the rough surface. CONCLUSIONS: The He plasma treatments on PIM zirconia implants made the surface more hydrophilic and enhanced the osseointegration of the implants without changing the micro-topography.

Effects of non-thermal atmospheric pressure pulsed plasma on the adhesion and durability of resin composite to dentin.

This study investigated the effect of low-power, non-thermal atmospheric pressure plasma (NT-APP) treatments, in pulsed and conventional modes, on the adhesion of resin composite to dentin and on the durability of the bond between resin composite and dentin. A pencil-type NT-APP jet was applied in pulsed and conventional modes to acid-etched dentin. The microtensile bond strength (MTBS) of resin composite to dentin was evaluated at 24 h and after thermocycling in one control group (no plasma) and in two experimental groups (pulsed plasma and conventional plasma groups) using the Scotchbond Multi-Purpose Plus Adhesive System. Data were analyzed using two-factor repeated-measures anova and Weibull statistics. Fractured surfaces and the bonded interfaces were evaluated using a field-emission scanning electron microscope. Although there were no significant differences between the plasma treatment groups, the plasma treatment improved the MTBS compared with the control group. After thermocycling, the MTBS did not decrease in the control or conventional plasma group but increased in the pulsed plasma group. Thermocycling increased the Weibull moduli of plasma-treated groups. In conclusion, plasma treatment using NT-APP improved the adhesion of resin composite to dentin. Using a pulsed energy source, the energy delivered to the dentin was effectively reduced without any reduction in bond strength or durability.

Plasma in dentistry: a review of basic concepts and applications in dentistry.

OBJECTIVE: Plasma-related technologies are essential in modern industries. Recently, plasma has attracted increased attention in the biomedical field. This paper provides a basic knowledge of plasma and a narrative review of plasma applications in dentistry. MATERIALS AND METHODS: To review plasma applications in dentistry, an electronic search in PubMed, SCOPUS and Google scholar up to December 2012 was done. This was followed by extensive hand searching using reference lists from relevant articles. CONCLUSION: There have been attempts to apply plasma technology in various fields of dentistry including surface modifications of dental implants, adhesion, caries treatment, endodontic treatment and tooth bleaching. Although many studies were in early stages, the potential value of plasma for dental applications has been demonstrated. To enlarge the scope of plasma applications and put relevant research to practical use, interdisciplinary research with participation of dental professionals is required.

Comparison of shear test methods for evaluating the bond strength of resin cement to zirconia ceramic.

OBJECTIVE: This study compared the sensitivity of three shear test methods for measuring the shear bond strength (SBS) of resin cement to zirconia ceramic and evaluated the effects of surface treatment methods on the bonding. MATERIALS AND METHODS: Polished zirconia ceramic (Cercon base, DeguDent) discs were randomly divided into four surface treatment groups: no treatment (C), airborne-particle abrasion (A), conditioning with Alloy primer (Kuraray Medical Co.) (P) and conditioning with Alloy primer after airborne-particle abrasion (AP). The bond strengths of the resin cement (Multilink N, Ivoclar Vivadent) to the zirconia specimens of each surface treatment group were determined by three SBS test methods: the conventional SBS test with direct filling of the mold (Ø 4 mm × 3 mm) with resin cement (Method 1), the conventional SBS test with cementation of composite cylinders (Ø 4 mm × 3 mm) using resin cement (Method 2) and the microshear bond strength (µSBS) test with cementation of composite cylinders (Ø 0.8 mm × 1 mm) using resin cement (Method 3). RESULTS: Both the test method and the surface treatment significantly influenced the SBS values. In Method 3, as the SBS values increased, the coefficients of variation decreased and the Weibull parameters increased. The AP groups showed the highest SBS in all of the test methods. Only in Method 3 did the P group show a higher SBS than the A group. CONCLUSIONS: The µSBS test was more sensitive to differentiating the effects of surface treatment methods than the conventional SBS tests. Primer conditioning was a stronger contributing factor for the resin bond to zirconia ceramic than was airborne-particle abrasion.

Application of the water subtraction algorithm in determining the degree of conversion of self-etching adhesives.

PURPOSE: This study evaluated the effect of residual water included within the FT-IR spectra on the calculation of the degree of conversion (DC) of a self-etching adhesive (SEA). MATERIALS AND METHODS: FT-IR spectra of a SEA (Adper Prompt SE, 3M ESPE) were obtained for different amounts of dentin powder, agitation times, and light-curing times. The measured DC (mDC) obtained from the IR spectra was compared to the apparent DC (aDC) from the adjusted IR spectra using the water subtraction algorithm (WSA), by which the water absorption band was subtracted from the obtained IR spectrum. RESULTS: When the SEA was mixed with 10 mg of dentin powder, the aDC was significantly higher than the mDC immediately after light curing (paired t-test, p < 0.001). With the increase in the amount of dentin powder, the mDC immediately after curing and the difference between the mDC and the aDC gradually increased. The amount of dentin powder, light-curing time, square of light-curing time, and time until measurement were the variables that significantly affected the aDC (linear mixed model, p < 0.05). However, the agitation time did not affect the aDC or the difference between the mDC and the aDC, except at 20 s. CONCLUSION: When the DC of SEA itself is measured with FT-IR, the mDC needs to be adjusted with the water subtraction algorithm. Clinically, SEA needs to be applied under conditions of prolonged contact with the dentin substrate and vigorous and prolonged drying.

Effect of the applied power of atmospheric pressure plasma on the adhesion of composite resin to dental ceramic.

PURPOSE: To evaluate the effect of applied power on dental ceramic bonding of composite resin using nonthermal atmospheric pressure plasma (APP). MATERIALS AND METHODS: A pencil-type APP torch was used to modify the surface chemical composition and hydrophilicity of dental ceramic and to improve the adhesion of composite resin to the surface. The effect of the applied power on chemical changes of the plasma polymer on a ceramic surface and the adhesive strength between the composite resin and feldspathic porcelain were examined. Adhesion was evaluated by comparing shear bond strengths (SBS) using the iris method. The chemical composition of the plasma polymer deposited on the ceramic surface was evaluated using x-ray photoelectron spectroscopy (XPS). Hydrophilicity was evaluated by contact angle measurements. The fracture mode at the interface was also evaluated. RESULTS: The APP treatment was effective and the SBS of the experimental groups were significantly higher than those of the negative control group (p < 0.05). Moreover, the SBS obtained with the APP treatment at the highest input voltage was statistically similar to the gold standard of HF etching and silane coupling-agent coating. Two-thirds of the fractures observed in the specimens bonded with application of APP were mixed and cohesive fractures. CONCLUSION: Application of APP enhanced adhesion by producing carboxyl groups on the ceramic surface and as a result by improving surface hydrophilicity. The carboxyl group contents in the plasma polymer on the ceramic surface increased as the applied power increased.

Flexural test as an alternative to tensile test for bond strength of resin cement to zirconia.

OBJECTIVE: There has been a great many technical difficulties in measuring the bond strengths between brittle dental substrates and materials, especially in preparing specimens. This study evaluated the validity of the relatively easy flexural bond strength (FBS) test in measuring bond strength of resin cement to zirconia as an alternative to the cumbersome tensile bond strength (TBS) and micro-tensile bond strength (MTBS) tests. MATERIALS AND METHODS: The FBS and TBS of resin cement to zirconia were measured experimentally after three surface treatments on a zirconia ceramic: air abrasion only (A), conditioning with Single Bond Universal (U) after air abrasion, and conditioning with Z-Prime Plus (Z) after air abrasion. The data were investigated using two-way analysis of variance (ANOVA), Weibull statistics, and a theoretical simulation. RESULTS: In both the FBS and TBS tests, the experimental data were consistent and quantitatively similar. First, according to ANOVA, the U group showed the highest bond strengths in both tests, followed by the Z group and the A group. In each surface treatment group, the FBS was always higher than the TBS. Second, the Weibull fitting showed the same order of strength in both tests (A < Z < U) and in all surface treatment groups (FBS > TBS). Third, the theoretical ratios calculated from the Weibull moduli agreed well with the experimental ratios of the FBS to the TBS. CONCLUSION: The FBS test can be an alternative to the TBS and MTBS tests in measuring the bond strength of brittle resin cement to zirconia.

Effects of blood contamination on microtensile bond strength to dentin of three self-etch adhesives.

This study evaluated the effects of blood contamination and decontamination methods during different steps of bonding procedures on the microtensile bond strength of two-step self-etch adhesives to dentin. Sixty extracted human molars were ground flat to expose occlusal dentin. The 60 molars were randomly assigned to three groups, each treated with a different two-step self-etch adhesive: Clearfil SE Bond, AdheSE and Tyrian SPE. In turn, these groups were subdivided into five subgroups (n = 20), each treated using different experimental conditions as follows: control group-no contamination; contamination group 1-CG1: primer application/ contamination/primer re-application; contamination group 2-CG2: primer application/contamination/wash/dry/primer re-application; contamination group 3-CG3: primer application/adhesive application/light curing/contamination/ adhesive re-application/light curing; contamina- tion group 4-CG4: primer application/adhesive application/light curing/contamination/wash/ dry/adhesive re-application/light curing. Composite buildup was performed using Z250. After 24 hours of storage in distilled water at 37 degrees C, the bonded specimens were trimmed to an hourglass shape and serially sectioned into slabs with 0.6 mm2 cross-sectional areas. Microtensile bond strengths (MTBS) were assessed for each specimen using a universal testing machine. The data were analyzed by two-way ANOVA followed by a post hoc LSD test. SEM evaluations of the fracture modes were also performed. The contaminated specimens showed lower bond strengths than specimens in the control group (p < 0.05), with the exception of CG1 in the Clearfil SE group and CG2 and CG3 in the Tyrian SPE group. Among the three self-etch adhesives, the Tyrian SPE group exhibited a significantly lower average MTBS compared to the Clearfil SE Bond and AdheSE (p < 0.05) groups. Based on the results of the current study, it was found that blood contamination reduced the MTBS of all three self-etch adhesives to dentin, and water-rinsing was unable to overcome the effects of blood contamination.

Information resources and material selection in bonded restorations among Korean dentists.

PURPOSE: To elucidate how dentists access knowledge sources when choosing adhesive agents for bonded restoration and whether these resources influenced the selection of materials. MATERIALS AND METHODS: A national survey was carried out involving dentists in South Korea. The questionnaire included the status of the operator, clinical techniques, and materials. A total of 12,193 e-mails were distributed, 2632 were opened by recipients, and 840 responses were collected. RESULTS: For primary information resources in material selection, 55.8% (n = 469) of the responders mentioned continuing education. This selection criteria varied according to the working status of the clinician (p < 0.0001). The choice of bonding system was influenced by of the length of the career (p < 0.0001), and the preferred bonding systems differed according to the source of the information (p = 0.035). CONCLUSION: The popular bonding systems were not ranked according to the bonding strategy, but a preference was found for specific brands or manufacturers. To decrease the confusion of clinicians related to the selection of bonding materials, evidence-based guidelines need to be comprehensibly organized and efficiently approached in clinics.

Two-year clinical effectiveness of adhesives and retention form on resin composite restorations of non-carious cervical lesions.

The current study investigated the clinical effectiveness of three adhesives and the use of retention form in Class V resin composite restorations of the non-carious cervical lesion (NCCL) over a two-year period. One-hundred and fifty NCCLs in 39 patients were restored with resin composites according to six experimental protocols combining the presence or absence of retention form and three adhesives: ScotchBond Multi-Purpose (MP, 3M ESPE), an experimental adhesive (EX, Vericom) and Adper Prompt (AP, 3M ESPE). All restorations were evaluated at baseline, 6, 12 and 24 months. Modified United States Public Health Service (USPHS) criteria were used to evaluate the restorations. MP was found to have significantly superior marginal adaptation than AP in cumulative logistic regression analysis (odds ratio, 2.12; 95% confidence interval, 1.05-4.31; p = 0.0397). In analysis using the Pearson's Chi-square or Fisher's Exact Test to compare the clinical performance of restorations with and without retention form, EX with retention form showed a significantly higher retention rate at two years than that without retention form (p = 0.0089). Restorations with retention form also showed significantly less marginal discoloration than those without retention form in all three adhesives (p = 0.0336).

Anatomical analysis of the resected roots of mandibular first molars after failed non-surgical retreatment.

OBJECTIVES: Understanding the reason for an unsuccessful non-surgical endodontic treatment outcome, as well as the complex anatomy of the root canal system, is very important. This study examined the cross-sectional root canal structure of mandibular first molars confirmed to have failed non-surgical root canal treatment using digital images obtained during intentional replantation surgery, as well as the causative factors of the failed conventional endodontic treatments. MATERIALS AND METHODS: This study evaluated 115 mandibular first molars. Digital photographic images of the resected surface were taken at the apical 3 mm level and examined. The discolored dentin area around the root canal was investigated by measuring the total surface area, the treated areas as determined by the endodontic filling material, and the discolored dentin area. RESULTS: Forty 2-rooted teeth showed discolored root dentin in both the mesial and distal roots. Compared to the original filled area, significant expansion of root dentin discoloration was observed. Moreover, the mesial roots were significantly more discolored than the distal roots. Of the 115 molars, 92 had 2 roots. Among the mesial roots of the 2-rooted teeth, 95.7% of the roots had 2 canals and 79.4% had partial/complete isthmuses and/or accessory canals. CONCLUSIONS: Dentin discoloration that was not visible on periapical radiographs and cone-beam computed tomography was frequently found in mandibular first molars that failed endodontic treatment. The complex anatomy of the mesial roots of the mandibular first molars is another reason for the failure of conventional endodontic treatment.

Comparison of the color of natural teeth measured by a colorimeter and Shade Vision System.

OBJECTIVES: The objectives were to measure the difference in the color and color parameters of natural teeth measured by a tristimulus colorimeter (CM, used as a reference) and Shade Vision System (SV), and to determine the influence of color parameters on the color difference between the values measured by two instruments. METHOD: Color of 12 maxillary and mandibular anterior teeth was measured by CM and SV for 47 volunteers (number of teeth=564). Color parameters such as CIE L*, a* and b* values, chroma and hue angle measured by two instruments were compared. Chroma was calculated as C*ab=(a*2 = b*2)1/2, and hue angle was calculated as h degrees =arctan(b*/a*). The influence of color parameters measured by CM on the color difference (DeltaE*(ab)) between the values measured by two instruments was analyzed with multiple regression analysis (alpha=0.01). RESULTS: Mean DeltaE*(ab) value between the values measured by two instruments was 21.7 (+/-3.7), and the mean difference in lightness (CIE L*) and chroma was 16.2 (+/-3.9) and 13.2 (+/-3.0), respectively. Difference in hue angle was high as 132.7 (+/-53.3) degrees . Except for the hue angle, all the color parameters showed significant correlations and the coefficient of determination (r(2)) was in the range of 0.089-0.478. Based on multiple regression analysis, the standardized partial correlation coefficient (beta) of the included predictors for the color difference was -0.710 for CIE L* and -0.300 for C*(ab) (p<0.01). CONCLUSION: All the color parameters showed significant but weak correlations except for hue angle. When lightness and chroma of teeth were high, color difference between the values measured by two instruments was small. Clinical accuracy of two instruments should be investigated further.

Rheological characterization of composites using a vertical oscillation rheometer.

OBJECTIVES: The purpose of this study was to investigate the viscoelastic properties related to the handling characteristics of composites. METHODS: A custom-designed vertical oscillation rheometer (VOR) was used for the rheological measurements of composites. The VOR consists of three parts: (1) a measuring unit, (2) a deformation induction unit, and (3) a force-detecting unit. Two medium-viscous composites, Z100 and Z250, and two packable composites, P60 and SureFil, were tested. A dynamic oscillatory test was used to evaluate the storage modulus (E'), loss modulus (E''), and loss tangent (tan delta) of the composites as a function of frequency (omega) from 0.1 to 20Hz at 23 degrees C. RESULTS: The E' and E'' increased with increasing frequency and showed differences in magnitude among brands. The complex moduli E* of the composites at omega=2 Hz, normalized to that of Z100, were 2.16 (Z250), 4.80 (P60), and 25.21 (SureFil). The magnitudes and frequency characteristic of loss tangent differed significantly among brands. The relationship among the complex modulus E*, the phase angle delta, and the frequency omega was represented by the frequency domain phasor form E*(omega)e(idelta)=E*(omega) angledelta. SIGNIFICANCE: The viscoelasticities of composites, which influence handling characteristics, are significantly different among brands. The VOR is a relatively simple device for the dynamic rheological measurement of dental composites. The loci of the frequency domain phasor plots in a complex plane are a valuable method of representing the viscoelastic properties of composites.

Influence of cavity dimension and restoration methods on the cusp deflection of premolars in composite restoration.

OBJECTIVES: The aim of this study was to measure the cusp deflection by polymerization shrinkage during composite restoration for mesio-occluso-distal (MOD) cavities in premolars, and to examine the influence of cavity dimension, C-factor and restoration method on the cusp deflection. METHODS: Thirty extracted maxillary premolars of similar size were prepared with four different sizes of MOD cavity, and divided into six groups. The width and depth of the pulpal wall of the cavity were as follows: group 1: 1.5x1 mm, group 2: 1.5x2 mm, group 3: 3x1 mm, and groups 4-6: 3x2 mm. Groups 1-4 were restored using a bulk filling with a composite. Group 5 was restored incrementally, and group 6 was restored with an indirect composite inlay. Cusp deflections were measured using LVDT transducers. The cusp deflections were compared between groups using ANOVA and Scheffe tests, and a correlation analysis was done. RESULTS: The cusp deflections of groups 1-4 were 12.1 (2.2), 17.2 (1.9), 16.2 (0.8) and 26.4 (4.2) microm, respectively. There was a strong positive correlation between the length cubed divided by the thickness cubed of the remaining cusp (L3/T3) and cusp deflection. The C-factor was related to the % flexure (100xcusp deflection/cavity width). The cusp deflections of groups 5 and 6 were 17.4 (2.0) and 17.9 (1.4) microm, respectively, which were much lower values than those of group 4. SIGNIFICANCE: The cusp deflection increased with increasing cavity dimension and C-factor. Use of an incremental filling technique or an indirect composite inlay restoration could reduce the cuspal strain.

Curing effectiveness of a light emitting diode on dentin bonding agents.

This study tested the hypothesis that dentin bonding agents (DBAs) cured with a light emitting diode (LED) light curing unit (LCU) would not show a statistically significant different dentin shear bond strength (DSBS) relative to a halogen LCU, when the LED and halogen LCUs had a supposedly similar irradiance. Five commercial DBAs were tested: ScotchBond Multipurpose, Single Bond, One Step, Clearfil SE Bond, and Adper Prompt. The LCUs used in this study were a VIP (Bisco) for the halogen light and an Elipar FreeLight (3M ESPE) for the LED. First, the emission spectrum and spectral irradiance of both LCUs were investigated. Next, the DSBS of the DBAs cured with each LCU was measured. Two-way analysis of variance was used to analyze whether there were differences in DSBS resulting from the type of LCU and DBA used. The halogen LCU showed a higher total irradiance value relative to the LED LCU, but the difference of spectral irradiance was reduced in the efficient wavelength ranges for camphoroquinone activation. Although the DBAs cured with both types of LCUs showed similar DSBS values, Clearfil SE Bond showed the highest DSBS value when cured with a halogen light. Therefore, the null hypothesis of this study was rejected, indicating that the curing effectiveness of the LED LCU on some DBAs can be lower than that of a halogen LCU in terms of bond strength.

Effect of light-cure time of adhesive resin on the thickness of the oxygen-inhibited layer and the microtensile bond strength to dentin.

A thick oxygen-inhibited layer (OIL) on a cured adhesive layer (AL) is believed to result in both good adaptation of composite resin (CR) and high bond strength. A high degree of conversion (DC) of the AL is also needed for durable bonding. This study evaluated the hypothesis that increasing the DC by prolonging the light-curing time of adhesive bonding resin might decrease the bond strength of the adhesive to dentin because of the subsequent thinning of the OIL thickness. The OIL thickness and the DC of solvent-removed One Step and D/E bonding resin of All Bond 2 (Bisco, USA) were measured simultaneously with FT-NIR spectroscopy according to increasing light-cure times (10, 20, 30, and 60 s) so as to evaluate their effect on the microtensile bond strength. The bonded interfaces were evaluated using scanning electron microscopy. Excessive irradiation of light-curing adhesives increased the DC, but decreased the OIL thickness. When the OIL was significantly thin by curing the adhesives for 30 or 60 s, defects were observed at the interface between the AL and the CR, as well as at the interface between the AL and the hybrid layer. When the OIL was thick, free radicals from the overlying CR may have diffused into the unreacted monomer mixtures of the OIL, chemically connecting the cured AL and the newly curing composite. It was found that to obtain maximum dentin bond strength, light-curing adhesives should be cured for the irradiation time recommended by the manufacturer.