Understanding, controlling and optimising the cooling of waste thermal treatment beds including STARx Hottpads.

STARx (Self-sustaining Treatment for Active Remediation ex situ) is a thermal treatment strategy for contaminated soils and organic wastes. Key to this technology is that organics are embedded in porous matrix beds (e.g. sand). STARx induces a self-sustaining smouldering combustion front that traverses the bed, burning away the embedded contaminants/wastes. The time and cost effectiveness of this technology is largely dictated by the time required for cooling of the hot, clean, porous matrix bed that remains after treatment. This study is the first to explore the cooling of these beds. A suite of novel simulations investigated the influence of key parameters on bed-cooling time. The results reveal that cooling time decreased nearly linearly with decreases of volume-averaged bed temperature and bed bulk density. Increased injection air fluxes led to the non-linear decrease of cooling time. Also, cooling time was negatively impacted by bed temperature inhomogeneity, which influenced preferential air flow through cooler regions of the bed, bypassing hotter regions. From these results, using lower bulk density bed materials, increased air fluxes and enhancing wall insulation to improve bed temperature homogeneity were identified as system optimisations to reduce cooling times. While the aim of this research is to improve the STARx cooling process, the results are also highly applicable to many similar engineering systems that involve hot porous bed cooling.

Remediation of PFAS-Contaminated Soil and Granular Activated Carbon by Smoldering Combustion.

This study explored smoldering combustion for remediating polyfluoroalkyl substance (PFAS)-impacted granular activated carbon (GAC) and PFAS-contaminated soil. GAC, both fresh and PFAS-loaded, was employed as the supplemental fuel supporting smoldering in mixtures with sand (≈175 mg PFAS/kg GAC-sand), with PFAS-spiked, laboratory-constructed soil (≈4 mg PFAS/kg soil), and with a PFAS-impacted field soil (≈0.2 mg PFAS/kg soil). The fate of PFAS and fluorine was quantified with soil and emission analyses, including targeted PFAS and suspect screening as well as hydrogen fluoride and total fluorine. Results demonstrated that exceeding 35 g GAC/kg soil resulted in self-sustained smoldering with temperatures exceeding 900 °C. Post-treatment PFAS concentrations of the treated soil were near (2 experiments) or below (7 experiments) detection limits (0.0004 mg/kg). Further, 44% of the initial PFAS on GAC underwent full destruction, compared to 16% of the PFAS on soil. Less than 1% of the initial PFAS contamination on GAC or soil was emitted as PFAS in the quantifiable analytical suite. Results suggest that the rest were emitted as altered, shorter-chain PFAS and volatile fluorinated compounds, which were scrubbed effectively with GAC. Total organic fluorine analysis proved useful for PFAS-loaded GAC in sand; however, analyzing soils suffered from interference from non-PFAS. Overall, this study demonstrated that smoldering has significant potential as an effective remediation technique for PFAS-impacted soils and PFAS-laden GAC.

STARx Hottpad for smoldering treatment of waste oil sludge: Proof of concept and sensitivity to key design parameters.

Growing stockpiles of waste oil sludge (WOS) are an outstanding problem worldwide. Self-sustaining Treatment for Active Remediation applied ex situ (STARx) is a treatment technology based on smoldering combustion. Pilot-scale experiments for the STARx Hottpad prove this new concept for the mobile treatment of WOS mixed intentionally with sand or contaminated soil. The experiments also allowed for the calibration and validation of a smoldering propagation numerical model. The model was used to systematically explore the sensitivity of Hottpad performance to system design, operational parameters, and environmental factors. Pilot-scale (~1.5 m width) simulations investigated sensitivity to injected air flux, WOS saturation, heterogeneity of intrinsic permeability, and heterogeneity of WOS saturation. Results reveal that Hottpad design is predicted to be successful for WOS treatment across a wide range of scenarios. The operator can control the rate of WOS destruction and extent of treatment by increasing the air flux injected into the bed. The potential for smoldering channeling to develop was demonstrated for the first time. Under certain conditions, such as WOS saturations of 80%, high heterogeneity of WOS saturations, or moderate to high heterogeneity of soil permeability, smoldering channeling was predicted to accelerate to the point that remedial performance was degraded. Field-scale simulations (~10 m width) predicted successful treatment, with WOS destruction rates an order of magnitude higher than the pilot-scale and treatment times increasing only linearly with bed height. This work is a key step toward the design and effective operation of field STARx Hottpad systems for eliminating WOS.

Low Permeability Zone Remediation via Oxidant Delivered by Electrokinetics and Activated by Electrical Resistance Heating: Proof of Concept.

This study proposes and proves (in concept) a novel approach of combining electrokinetic (EK)-assisted delivery of an oxidant, persulfate (PS), and low temperature electrical resistivity heating (ERH), to activate PS, to achieve remediation of contaminated, low permeability soil. This unique combination is able to overcome existing challenges in remediating low permeability materials, particularly associated with delivering remediants. A further benefit of the approach is the use of the same electrodes for both EK and ERH phases. Experiments were conducted in a laboratory-scale sand tank packed with silt and aqueous tetrachloroethene (PCE) and bracketed on each side by an electrode. EK first delivered unactivated PS throughout the silt. ERH then generated and sustained the target temperature to activate the PS. As a result, PCE concentrations decreased to below detection limit in the silt in a few weeks. Moreover, it was found that activating PS at ∼36 °C eliminated more PCE than activating it at >41 °C. It is expected this results from the reactive SO4•- radical being generated more slowly, which ensures more complete reaction with the contaminant. The novel application of EK-assisted PS delivery followed by low temperature ERH appears to be a viable strategy for low permeability contaminated soil remediation.

Continuous, self-sustaining smouldering destruction of simulated faeces.

A new approach for the rapid destruction of human waste using smouldering combustion is presented. Recently, self-sustaining smouldering combustion was shown to destroy the organic component of simulated human solid waste and dog faeces resulting in the sanitization of all pathogens using a batch process (Yermán et al., 2015). Here, a continuous smouldering process is demonstrated for the first time, allowing for a much smaller reactor size and much less energy input per mass of waste treated. The self-sustained smouldering of simulated human faeces mixed with sand is evaluated over long periods (more than 16 h) based on a single ignition. The key process of intermittent self-sustained smouldering, in which the reaction is terminated and restarted by only turning the air off and on, is demonstrated. Experiments examine the influence of two key operator controls: airflow rate and set elevation of the quasi-steady-state smouldering front in a 37 cm high reactor. Quasi-steady-state fuel destruction rates from 93 g/h to 12 g/h were achieved by varying the superficial flow velocity from 7.4 cm/s to 0.11 cm/s, the latter with a velocity approximately an order of magnitude lower than possible for a self-sustaining reaction in an equivalent batch system. Excess energy of up to 140 J/g of sand was recovered from the clean sand produced in each cycle, which could be used to further increase the energy efficiency of this novel waste treatment system.

Quantified Pore-Scale Nanoparticle Transport in Porous Media and the Implications for Colloid Filtration Theory.

This study evaluates the pore-scale distribution of silver nanoparticles during transport through a sandy porous medium via quantitative synchrotron X-ray computed microtomography (qSXCMT). The associated distributions of nanoparticle flow velocities and mass flow rates were obtained by coupling these images with computational fluid dynamic (CFD) simulations. This allowed, for the first time, the comparison of nanoparticle mass flow with that assumed by the standard colloid filtration theory (CFT) modeling approach. It was found that (i) 25% of the pore space was further from the grain than assumed by the CFT model; (ii) the average pore velocity agreed well between results of the coupled qSXCMT/CFD approach and the CFT model within the model fluid envelope, although the former were 2 times larger than the latter in the centers of the larger pores and individual velocities were upwards of 20 times those in the CFT model at identical distances from grain surfaces ; and (iii) approximately 30% of all nanoparticle mass and 38% of all nanoparticle mass flow occurred further away from the grain surface than expected by the CFT model. This work suggests that a significantly smaller fraction of nanoparticles than expected will contact a grain surface by diffusion via CFT models, likely contributing to inadequate CFT model nanoparticle transport predictions.

Smoldering Remediation of Coal-Tar-Contaminated Soil: Pilot Field Tests of STAR.

Self-sustaining treatment for active remediation (STAR) is an emerging, smoldering-based technology for nonaqueous-phase liquid (NAPL) remediation. This work presents the first in situ field evaluation of STAR. Pilot field tests were performed at 3.0 m (shallow test) and 7.9 m (deep test) below ground surface within distinct lithological units contaminated with coal tar at a former industrial facility. Self-sustained smoldering (i.e., after the in-well ignition heater was terminated) was demonstrated below the water table for the first time. The outward propagation of a NAPL smoldering front was mapped, and the NAPL destruction rate was quantified in real time. A total of 3700 kg of coal tar over 12 days in the shallow test and 860 kg over 11 days in the deep test was destroyed; less than 2% of total mass removed was volatilized. Self-sustaining propagation was relatively uniform radially outward in the deep test, achieving a radius of influence of 3.7 m; strong permeability contrasts and installed barriers influenced the front propagation geometry in the shallow test. Reductions in soil hydrocarbon concentrations of 99.3% and 97.3% were achieved in the shallow and deep tests, respectively. Overall, this provides the first field evaluation of STAR and demonstrates that it is effective in situ and under a variety of conditions and provides the information necessary for designing the full-scale site treatment.

Method for obtaining silver nanoparticle concentrations within a porous medium via synchrotron X-ray computed microtomography.

Attempts at understanding nanoparticle fate and transport in the subsurface environment are currently hindered by an inability to quantify nanoparticle behavior at the pore scale (within and between pores) within realistic pore networks. This paper is the first to present a method for high resolution quantification of silver nanoparticle (nAg) concentrations within porous media under controlled experimental conditions. This method makes it possible to extract silver nanoparticle concentrations within individual pores in static and quasi-dynamic (i.e., transport) systems. Quantification is achieved by employing absorption-edge synchrotron X-ray computed microtomography (SXCMT) and an extension of the Beer-Lambert law. Three-dimensional maps of X-ray mass linear attenuation are converted to SXCMT-determined nAg concentration and are found to closely match the concentrations determined by ICP analysis. In addition, factors affecting the quality of the SXCMT-determined results are investigated: 1) The acquisition of an additional above-edge data set reduced the standard deviation of SXCMT-determined concentrations; 2) X-ray refraction at the grain/water interface artificially depresses the SXCMT-determined concentrations within 18.1 µm of a grain surface; 3) By treating the approximately 20 × 10(6) voxels within each data set statistically (i.e., averaging), a high level of confidence in the SXCMT-determined mean concentrations can be obtained. This novel method provides the means to examine a wide range of properties related to nanoparticle transport in controlled laboratory porous medium experiments.

Spectral induced polarization signatures of smoldering remediation enhanced with colloidal activated carbon: An experimental study.

Monitoring the remediation of soil and groundwater contaminated by organic compounds remains highly challenging. Thermal treatments, such as smoldering combustion, have become established remediation techniques for destroying contaminants. Smoldering combustion can now be supported by colloidal activated carbon (CAC), with CAC being able to both adsorb contaminants and supplement the fuel source for destroying them. Despite this potential, effective performance monitoring of smoldering remediation remains limited. The objective of this study is to investigate the potential of the spectral induced polarization (SIP) geoelectrical technique to assess the performance of smoldering remediation of soils supplemented with CAC. SIP column experiments were first conducted to assess the response of SIP (i.e., real and imaginary components of the complex electrical conductivity) to varying concentrations of CAC in imitated field soils that contain, or do not contain, organic matter (OM). Results demonstrate that increasing OM and CAC contents increase both the real and imaginary conductivities, with the imaginary conductivity also showing frequency dependence. Smoldering and SIP column experiments were then conducted to assess the effectiveness of SIP for detecting changes in soils of varying OM and CAC contents that have been remediated by smoldering. Examination of the soils before and after smoldering indicates that SIP can track the evolving real conductivity and imaginary conductivity (in particular) between different soil compositions and different stages of the remedial process. High resolution scanning electron microscopy imaging was performed on all samples to validate the SIP and smoldering experiments, confirming significant reductions in carbon after smoldering. Overall, this study suggests that SIP has potential to track changes associated with the addition of remedial fluids like CAC in the subsurface, and the destruction of contaminants adsorbed to CAC by smoldering combustion.

Self-sustaining smoldering combustion for NAPL remediation: laboratory evaluation of process sensitivity to key parameters.

Smoldering combustion has been introduced recently as a potential remediation strategy for soil contaminated by nonaqueous phase liquids (NAPLs). Published proof-of-concept experiments demonstrated that the process can be self-sustaining (i.e., requires energy input only to start the process) and achieve essentially complete remediation of the contaminated soil. Those initial experiments indicated that the process may be applicable across a broad range of NAPLs and soils. This work presents the results of a series of bench-scale experiments that examine in detail the sensitivity of the process to a range of key parameters, including contaminant concentration, water saturation, soil type, and air flow rates for two contaminants, coal tar and crude oil. Smoldering combustion was observed to be self-sustaining in the range 28,400 to 142,000 mg/kg for coal tar and in the range 31,200 to 104,000 mg/kg for crude oil, for the base case air flux. The process remained self-sustaining and achieved effective remediation across a range of initial water concentrations (0 to 177,000 mg/kg water) despite extended ignition times and decreased temperatures and velocities of the reaction front. The process also exhibited self-sustaining and effective remediation behavior across a range of fine to coarse sand grain sizes up to a threshold maximum value between 6 mm and 10 mm. Propagation velocity is observed to be highly dependent on air flux, and smoldering was observed to be self-sustaining down to an air Darcy flux of at least 0.5 cm/s for both contaminants. The extent of remediation in these cases was determined to be at least 99.5% and 99.9% for crude oil and coal tar, respectively. Moreover, no physical evidence of contamination was detected in the treatment zone for any case where a self-sustaining reaction was achieved. Lateral heat losses to the external environment were observed to significantly affect the smoldering process at the bench scale, suggesting that the field-scale lower bounds on concentration and air flux and upper bound on grain size were not achieved; larger scale experiments and field trials where lateral heat losses are much less significant are necessary to define these process limits for the purposes of field application. This work provides valuable design data for pilot field trials of both in situ and ex situ smoldering remediation applications.

The influence of porous media heterogeneity on smouldering remediation.

Self-sustained Treatment for Active Remediation (STAR) is a thermal remediation technology that uses smouldering, a flameless form of combustion, for destroying organic contaminants in soil. Injected cold air flowing through the soil to the treatment zone supports the release of sufficient energy to maintain a self-sustained reaction and the propagation of the reaction through the contaminated zone as long as the airflow local to the reaction exceeds a minimum value. However, the distribution and magnitude of air flux vectors can be complex in the heterogeneous environment common at contaminated sites. This research presents the first investigation of smouldering remediation under varying degrees and patterns of permeability heterogeneity. Nine experiments examined smouldering remediation in contaminated layers of varying permeability arranged alone and in contrasting layers in series, in parallel, and in two distinct complex patterns. The results suggest that smouldering can successfully propagate across layer boundaries and through layers in series regardless of their permeability (at least down to 1 x 10-12 m2). However, fine layers were not smouldered for layers in parallel with a permeability ratio ≥ 3:1. Numerical modelling of these cases with a published smouldering model revealed that this occurred due to insufficient airflow in the fine layers in some cases, or conductive heat transfer (thermal coupling) between parallel layers in other cases. The more complex heterogeneity patterns underscored the importance of the connected length of the higher permeability pathway on airflow distribution and therefore on smouldering propagation. Disconnected coarse zones supported smouldering in both coarse and fine zones while connected coarse zones kept smouldering in the coarse pathway while bypassing fine zones. Overall, this research provides unique insights into understanding heterogeneous scenarios to ensure the successful application of smouldering remediation.

Scaling up self-sustained smouldering of sewage sludge for waste-to-energy.

Self-sustained smouldering combustion presents strong potential as a green waste-to-energy technique for a range of wastes, especially those with high moisture content like wastewater sewage sludge. While well-demonstrated in laboratory experiments, there is little known about scaling up this process to larger, commercial reactors. This paper addresses this knowledge gap by systematically conducting and analyzing experiments in a variety of reactors extending beyond the laboratory scale. This work reveals a robust treatment regime; however, it also identifies potential complications associated with perimeter heat losses at scale. Two key impacts, on the smouldering reactions and the air flow patterns, are shown to potentially degrade treatment if not properly understood and managed. Altogether, this study provides novel insight and guidance for scaling up smouldering science into practical, waste-to-energy systems.

Electrokinetically-enhanced emplacement of lactate in a chlorinated solvent contaminated clay site to promote bioremediation.

Bioremediation through the injection of electron donors and bacterial cultures is effective at treating chlorinated solvent contamination. However, it has had limited application in low permeability zones where amendments cannot be delivered successfully. This field-scale study investigated the application of electrokinetics to enhance the delivery of lactate at a clay site contaminated with chlorinated solvents. Groundwater and soil samples were collected before, during and for 1 year after the 71-day field test and analyzed for a wide suite of chemical and biological parameters. Lactate was successfully delivered to all monitoring locations. Lactate emplacement resulted in the stimulation of bacterial populations, specifically within the phylum Firmicutes, which contains fermenters and strict anaerobes. This likely led to biodegradation, as the field trial resulted in significant decreases in both soil and aqueous phase chlorinated solvent concentrations. Contaminant decreases were also partially attributable to dilution, given evidence of some advective lactate flux. This research provides evidence that electrokinetically-enhanced bioremediation has potential as a treatment strategy for contaminated low permeability strata.

Field test of electrokinetically-delivered thermally activated persulfate for remediation of chlorinated solvents in clay.

In situ chemical oxidation (ISCO) has demonstrated success in remediating soil and groundwater contaminated with chlorinated volatile organic compounds (CVOCs). However, its performance is often hindered in low-permeability or heterogeneous media due to an inability to effectively deliver the oxidants. This field-scale study investigated the novel approach of applying electrokinetics (EK) to enhance the delivery of persulfate in a low-permeability media and the ability of electrical resistance heating (ERH) to thermally activate the delivered persulfate. Results showed that 40% of the mass of total sulfur delivered was due to EK mechanisms, demonstrating that EK has the potential to enhance oxidant delivery. ERH may have activated some of the persulfate, but catalytic reactions with reduced forms of iron likely resulted in appreciable persulfate decomposition prior to ERH. Significant decreases (>80%) in the aqueous concentration of CVOCs was observed before and after ERH initiation, attributed to in situ transformation and physical processes (e.g., dilution). In situ transformation of CVOCs was assessed by compound-specific isotope analysis (CSIA) of 1,2-dichloroethane (1,2-DCA) samples collected after ERH application. Enrichment of 13C was only measured in the well with appreciable persulfate breakthrough, confirming dechlorination of 1,2-DCA. Results from this field study demonstrate that EK and ERH can be used for persulfate delivery and activation for remediation of CVOCs in low-permeability media.

Multidimensional validation of a numerical model for simulating a DNAPL release in heterogeneous porous media.

A fixed-volume release of 1,2-DCE, tracked in space and time with a light transmission/image analysis system, provided a data set for the infiltration, redistribution, and immobilisation of a dense non-aqueous phase liquid (DNAPL) in a heterogeneous porous medium. The two-dimensional bench scale flow cell was packed with a spatially correlated, random heterogeneous distribution of six sand types. In order to provide the necessary modelling parameters, detailed constitutive relationships were measured at the local scale for the six sands. These experiments revealed that nonwetting phase (NWP) relative permeability-saturation (k(rN)-S(W)) relationships are strongly correlated to sand type. Trends in the best-fit k(rN)-S(W) parameters reflected a positive correlation between mean grain diameter and the maximum NWP relative permeability, k(rN)(max). Multiphase flow simulations of the bench scale experiment best reproduced the experimental observations, producing excellent matches in both time and space, when the measured, correlated local scale k(rN)-S(W) relationships were employed.

Time scales of DNAPL migration in sandy aquifers examined via numerical simulation.

The time required for dense nonaqueous phase liquid (DNAPL) to cease migrating following release to the subsurface is a valuable component of a site conceptual model. This study uses numerical simulation to investigate the migration of six different DNAPLs in sandy aquifers. The most influential parameters governing migration cessation time are the density and viscosity of the DNAPL and the mean hydraulic conductivity of the aquifer. Releases of between 1 and 40 drums of chlorinated solvent DNAPLs, characterized by relatively high density and low viscosity, require on the order of months to a few years to cease migrating in a heterogeneous medium sand aquifer having an average hydraulic conductivity of 7.4 x 10(-3) cm/s. In contrast to this, the release of 20 drums of coal tar (rho(D)= 1061 kg/m(3), micro(D)= 0.161 Pa.s) requires more than 100 years to cease migrating in the same aquifer. Altering the mean hydraulic conductivity of the aquifer results in a proportional change in cessation times. Parameters that exhibit relatively little influence on migration time scales are the DNAPL-water interfacial tension, release volume, source capillary pressure, mean aquifer porosity, and ambient ground water hydraulic gradient. This study also demonstrates that low-density DNAPLs (e.g., coal tar) give rise to greater amounts of lateral spreading and greater amounts of pooling on capillary barriers than high-density DNAPLs such as trichloroethylene or tetrachloroethylene.

Electrokinetic-enhanced permanganate delivery and remediation of contaminated low permeability porous media.

Back diffusion of contaminants from low permeability strata has inhibited site remediation and closure due to an inability to deliver remediants into these strata. This study demonstrates the potential of electrokinetics (EK) to significantly reduce back diffusion of chlorinated compounds from low permeability porous media. Experiments were conducted in a two-dimensional sandbox packed with vertical layers of coarse sand and silt contaminated with aqueous trichloroethene (TCE). Three experiments, each approximately 41 days in duration, compared EK-enhanced in situ chemical oxidation (EK-ISCO) to EK or ISCO alone. EK-ISCO successfully delivered the oxidant (permanganate, PM) throughout the silt cross-section while ISCO without EK resulted only in PM delivery to the edges of the silt layer fringes. EK-ISCO resulted in a 4.4-fold reduction in TCE concentrations in the coarse sand compared to a 3.5-fold reduction from ISCO alone. EK-ISCO with a 25 mA current was found to be more effective than with 300 mA current. Overall, this study suggests that electrokinetics coupled with an appropriate in situ remediation technique, such as ISCO, can enhance remediation of lower permeability strata and limit the extent of contaminant back diffusion.

Application of self-sustaining smouldering combustion for the destruction of wastewater biosolids.

Managing biosolids, the major by-product from wastewater treatment plants (WWTPs), persists as a widespread challenge that often constitutes the majority of WWTP operating costs. Self-sustained smouldering combustion is a new approach for organic waste treatment, in which the waste - the combustion fuel - is destroyed in an energy efficient manner after mixing it with sand. Smouldering has never been applied to biosolids. Column experiments, using biosolids obtained from a WWTP, were employed to identify if, and under what conditions, smouldering could be used for treating biosolids. The parameter space in which smouldering was self-sustaining was mapped as a function of key system metrics: (1) sand/biosolids mass fraction, (2) biosolids moisture content, and (3) forced air flux. It was found that a self-sustaining reaction is achievable using biosolids with water content as high as 80% (with a biosolids lower heating value greater than 1.6 kJ/g). Moreover, results suggest that operator-controlled air flux can assist in keeping the reaction self-sustaining in response to fluctuations in biosolids properties. This proof-of-concept demonstrates the potential for smouldering as a new energy efficient biosolids disposal method for very wet (i.e., minimally processed) biosolids that may offer WWTPs significant operating cost savings. This study emphasizes smouldering's usefulness as a novel waste management technique.

Remediation of trichloroethylene-contaminated soils by star technology using vegetable oil smoldering.

Self-sustaining treatment for active remediation (STAR) is an innovative soil remediation approach based on smoldering combustion that has been demonstrated to effectively destroy complex hydrocarbon nonaqueous phase liquids (NAPLs) with minimal energy input. This is the first study to explore the smoldering remediation of sand contaminated by a volatile NAPL (trichloroethylene, TCE) and the first to consider utilizing vegetable oil as supplemental fuel for STAR. Thirty laboratory-scale experiments were conducted to evaluate the relationship between key outcomes (TCE destruction, rate of remediation) to initial conditions (vegetable oil type, oil: TCE mass ratio, neat versus emulsified oils). Several vegetable oils and emulsified vegetable oil formulations were shown to support remediation of TCE via self-sustaining smoldering. A minimum concentration of 14,000 mg/kg canola oil was found to treat sand exhibiting up to 80,000 mg/kg TCE. On average, 75% of the TCE mass was removed due to volatilization. This proof-of-concept study suggests that injection and smoldering of vegetable oil may provide a new alternative for driving volatile contaminants to traditional vapour extraction systems without supplying substantial external energy.

Evaluating four-dimensional time-lapse electrical resistivity tomography for monitoring DNAPL source zone remediation.

Practical, non-invasive tools do not currently exist for mapping the remediation of dense non-aqueous phase liquids (DNAPLs). Electrical resistivity tomography (ERT) exhibits significant potential but has not yet become a practitioner's tool due to challenges in interpreting the survey results at real sites. This study explores the effectiveness of recently developed four-dimensional (4D, i.e., 3D space plus time) time-lapse surface ERT to monitor DNAPL source zone remediation. A laboratory experiment demonstrated the approach for mapping a changing NAPL distribution over time. A recently developed DNAPL-ERT numerical model was then employed to independently simulate the experiment, providing confidence that the DNAPL-ERT model is a reliable tool for simulating real systems. The numerical model was then used to evaluate the potential for this approach at the field scale. Four DNAPL source zones, exhibiting a range of complexity, were initially simulated, followed by modeled time-lapse ERT monitoring of complete DNAPL remediation by enhanced dissolution. 4D ERT inversion provided estimates of the regions of the source zone experiencing mass reduction with time. Results show that 4D time-lapse ERT has significant potential to map both the outline and the center of mass of the evolving treated portion of the source zone to within a few meters in each direction. In addition, the technique can provide a reasonable, albeit conservative, estimate of the DNAPL volume remediated with time: 25% underestimation in the upper 2m and up to 50% underestimation at late time between 2 and 4m depth. The technique is less reliable for identifying cleanup of DNAPL stringers outside the main DNAPL body. Overall, this study demonstrates that 4D time-lapse ERT has potential for mapping where and how quickly DNAPL mass changes in real time during site remediation.