The medullary cavity morphology of the proximal femur influences the fixation pattern of the rectangular tapered short stem in total hip arthroplasty.

INTRODUCTION: This study aimed to evaluate differences in the pattern of fixation with a rectangular tapered short stem (Fitmore stem) due to proximal femoral medullary cavity morphology based on periprosthetic bone mineral density (BMD) and radiological findings. MATERIALS AND METHODS: We analyzed 105 consecutive patients (Dorr type A, 18; Dorr type B, 66; Dorr type C, 21) who underwent total hip arthroplasty using a Fitmore stem. Periprosthetic BMD was measured using dual-energy X-ray absorptiometry from 1 to 24 months postoperatively and radiological analysis was performed. Clinical outcomes were evaluated using the Harris hip score (HHS) and the University of California Los Angeles (UCLA) activity score preoperatively and 24 months postoperatively. RESULTS: At 24 months postoperatively, Dorr type C had significantly decreased BMD changes in Gruen zones 2, 6, and 7 compared to Dorr types A and B, and conversely, significantly increased BMD changes in zone 4 (p < 0.05). Dorr type C had significantly greater subsidence than the other types (p < 0.01) and significantly higher cortical hypertrophy in zone 3 (p < 0.01). Stress shielding was not significantly different between Dorr types. The preoperative and postoperative HHS and UCLA activity scores showed no significant differences between the Dorr types. CONCLUSIONS: In Dorr type C, BMD significantly decreased in the proximal femur with a rectangular tapered short stem, suggesting that the stem was fixed at the distal part. Careful observation of this prosthesis over time is needed in patients with Dorr type C.

Propensity of the tight mid-flexion and loose flexion gap despite the adjustment of extension and flexion gaps in Oxford unicompartmental knee arthroplasty: retrospective study.

PURPOSE: A well-balanced joint gap is necessary in Oxford unicompartmental knee arthroplasty (OUKA) to prevent mobile-bearing dislocation. While the gaps between 20° (extension) and 100° (flexion) are precisely adjusted using the incremental mill system, there has been insufficient evaluation of gaps in other angles. We hypothesized that the gap is not always the same in other angles. This retrospective study aimed to evaluate the gap in full-extension (0°), mid-flexion (60°) and deep flexion (130°) for comparison with those in extension and flexion gaps. METHODS: We evaluated 119 knees in 83 patients (51 females, 31 males, aged 71.9 years). The full-extension and mid-flexion gaps were compared with the extension gap, and the deep flexion gap was contrasted with the flexion gap. Each gap was classified into isometric, tight or loose, for evaluation of contributing factors. RESULTS: Although the full-extension gap tended to be isometric (45%), the mid-flexion tended to be tight (48%), whereas the deep-flexion was loose in most knees (84%) (P = 0.002). The tight mid-flexion and loose deep flexion gap pattern accounted for 44% of the total knees, especially so with smaller femoral components (P = 0.004). CONCLUSION: Our results highlight the propensity of tight mid-flexion and loose flexion gap despite the adjustment of extension and flexion gaps in OUKA. Although the effect of such a minor gap imbalance is still unknown, the pattern was more prevalent in patients with smaller-sized femoral components. Use of a larger femoral component may equalize the gap throughout the motion arc.

Pre-milling technique improves the accuracy of posterior femoral condyle cut and reduces the tibial recut in Oxford unicompartmental knee arthroplasty.

BACKGROUND: Recuts are sometimes needed in UKA because of inadequate posterior tibial cut thickness. We investigated the efficacy of a pre-milling technique (the first milling is done prior to the posterior condylar cut) in Oxford unicompartmental knee arthroplasty to enhance bone cut thickness and to minimize tibial recuts. PATIENTS AND METHODS: Between January 2021 and January 2023, a posterior condyle cut was made before milling in 213 knees in 152 patients (conventional group), while the pre-milling technique was used in 198 knees in 140 patients (pre-milling group). The thickness of the posterior condyle and the rate of tibial recuts were compared between the groups. RESULTS: The bone cut thickness was thinner in the conventional group than in the pre-milling group in small-size (4.7 mm ± 0.6 mm and 5.0 mm ± 0.6 mm, P = 0.0001) and in medium-size (5.1 mm ± 0.5 mm and 5.4 mm ± 0.5 mm, 0.0001) femoral components, whereas there was no difference in large-size femoral components. However, the thickness was still less than the component thickness (5.17 mm for small, 5.57 mm for medium and 6.17 mm for large) in both groups. Tibial recuts were more prevalent in the conventional group than in the pre-milling group (14 knees, 7%, 3 knees 2%, P = 0.002). CONCLUSIONS: The pre-milling technique was found to increase the bone cut thickness in small and medium femoral components, reducing the need for tibial recuts. Further research is warranted to optimize the pre-milling technique and to investigate its long-term impact on patient outcomes.

Trans patellar tendon sagittal tibial cut for lateral unicompartmental knee arthroplasty-location of the split- CT simulation study.

BACKGROUND: In lateral unicompartmental knee arthroplasty (UKA), a sagittal cut is often performed through the patellar tendon (PT). Although the approach is likely widely used, it has not been described in detail, especially regarding the site of the split. This study aimed to clarify where the split should be made. METHODS: This single-center retrospective cohort study included 49 consecutive patients and 51 knees with lateral osteoarthritis. Using preoperative computed tomography, we measured the distance from the medial edge of the PT to the intersection of the PT and the sagittal cutting line, defined as a line parallel to the Akagi's line and passing the tip of the lateral tibial spine. RESULTS: The sagittal cut line passed a mean of 45 ± 11% of the patellar tendon width from the PT medial edge. CONCLUSIONS: The tendon split should be made just medial to the center of the PT because it is where the sagittal cut line for lateral UKA passes.

Approximately 41% of knees have a looser gap in full extension than in 20° flexion after Oxford unicompartmental arthroplasty.

INTRODUCTION: In Oxford unicompartmental knee arthroplasty (OUKA), the flexion and extension gaps should be adjusted to prevent mobile-bearing dislocation. The extension gap is recommended to be evaluated in the 20° flexion position to avoid underestimation due to tension of the posterior capsule. However, we have become aware of a looser gap in full extension than in 20° flexion in some instances. MATERIALS AND METHODS: We retrospectively investigated 83 knees in 60 patients who underwent OUKA between January and June 2020. During surgery, the extension gaps were measured in both full extension and 20° flexion. The knees were classified into two groups: the gap was looser in full extension (0° group), and the gap was equal or looser in 20° flexion than in full extension (20° group). The hip-knee-ankle angle (HKAA), the lateral distal femoral angle (LDFA), the medial proximal tibia angle (MPTA), the posterior tibial slope angle (PTSA), and the last spigot size were also measured and compared between the groups. RESULTS: There was looseness in approximately 41% of knees (34 out of 83 knees) in full extension. In the knees in the 0° group, the last spigot size was significantly smaller (median 1 and 2, P < 0.01). However, there were no significant differences in the HKAA, MPTA, LDFA or PTSA between the groups. CONCLUSIONS: Approximately 41% of knees have a looser gap in full extension than in 20° flexion after OUKA. Further investigation is needed to better understand which extension gap should be used in such cases, and to find the contributing factors in loose full extension gap other than the size of the last spigot.

Effects of Unrestricted Kinematically Aligned Total Knee Arthroplasty with a Modified Soft-Tissue Respecting Technique on the Deformity of Limb Alignment in Japanese Patients.

Background and Objectives: Unrestricted kinematic alignment total knee arthroplasty (KA-TKA) with a soft-tissue respecting technique (STRT) is a soft-tissue-dependent tibial resection entailing the restoration of the original soft-tissue tension using ligamentotaxis after resurfacing the femur, based on the concept of restoring the native or pre-osteoarthritis alignment in each patient. However, there is no consensus on the indications of unrestricted KA-TKA with the STRT. We modified the STRT, followed by an investigation of the effects of surgery on the postoperative hip-knee-ankle angle (HKAA). Materials and Methods: We retrospectively analyzed the clinical background data, including the preoperative and postoperative HKAA, of 87 patients who underwent unrestricted KA-TKA with the modified STRT. Univariate and multivariate analyses were performed to determine the factors affecting the postoperative HKAA. A receiver operating characteristic (ROC) curve was plotted to investigate the change in the cut-off values of preoperative HKAA with respect to the safe zone of the postoperative HKAA. We generated two regression models, the linear regression model and generalized additive model (GAM) using machine learning, to predict the postoperative HKAA. Results: Univariate and multivariate analyses revealed the preoperative HKAA as the factor most relevant to the postoperative HKAA. ROC analysis revealed that the preoperative HKAA exhibited a high predictive utility, with a cut-off value of -10°, when the safe range of postoperative HKAA was set at ±5°. The GAM was the superior machine learning model, indicating a non-linear association between the preoperative and postoperative HKAA. Patients with preoperative HKAAs ranging from -18° to 4° were more likely to fall within the ±5° safe range of the postoperative HKAA. Conclusions: The preoperative HKAA influences the postoperative HKAA in unrestricted KA-TKA with the modified STRT. Machine learning using the GAM may contribute to the selection of patients eligible for the surgical approach.

Paracrine effect of the stromal vascular fraction containing M2 macrophages on human chondrocytes through the Smad2/3 signaling pathway.

The adipose-derived stromal vascular fraction (SVF) is composed of a heterogeneous mix of adipose-derived stem cells (ADSCs), macrophages, pericytes, fibroblasts, blood, and other cells. Previous studies have found that the paracrine effects of SVF cells may be therapeutic, but their role in osteoarthritis treatment remains unclear. This study aimed to investigate the therapeutic effect of SVF cells on chondrocytes. Chondrocytes were seeded on culture plates alone (control) or cocultured with SVF or ADSCs on cell culture inserts. After 48 h of coculture, chondrocyte collagen II, tissue inhibitors of metalloproteinases-3 (TIMP-3), and matrix metalloproteinases-13 (MMP-13) messenger RNA (mRNA) expression levels were evaluated using reverse-transcription polymerase chain reaction, and the transforming growth factor-ß (TGF-ß) levels in the supernatant were measured using ELISA. Immunohistochemical staining and flow cytometry were used to evaluate the macrophages in the SVF. These macrophages were characterized according to phenotype using the F4/80, CD86, and CD163 markers. To determine whether the Smad2/3 signaling pathways were involved, the chondrocytes were pre-treated with a Smad2/3 phosphorylation inhibitor and stimulated with the SVF, and then Smad2/3 phosphorylation levels were analyzed using western blot. The mRNA expression levels of various paracrine factors and chondrocyte pellet size were also assessed. Collagen II and TIMP-3 expression were higher in the SVF group than in the ADSC group and controls, while MMP-13 expression was the highest in the ADSC group and the lowest in the controls. TGF-ß levels in the SVF group were also elevated. Immunohistochemical staining and flow cytometry revealed that the macrophages in the SVF were of the anti-inflammatory phenotype. Western blot analysis showed that the SVF increased Smad2/3 phosphorylation, while Smad2/3 inhibitors decreased phosphorylation. Smad2/3 inhibitors also reduced the expression of various other paracrine factors and decreased chondrocyte pellet size. These findings suggested that the paracrine effect of heterogeneous cells, such as anti-inflammatory macrophages, in the SVF partly supports chondrocyte regeneration through TGF-ß-induced Smad2/3 phosphorylation.

Short distance from the keel to the posterior tibial cortex is associated with fracture after cementless Oxford UKA in Asian patients.

PURPOSE: Tibial plateau fractures are serious complications of Oxford mobile-bearing unicompartmental knee arthroplasty (OUKA). This study examined where the fracture lines arises and evaluated the keel-cortex distances (KCDs) using three-dimensional computed tomography (3D-CT) and the effects of technical error (assessed by tibial component positions) and proximal tibial morphology on the KCDs. METHODS: This retrospective study included 217 OUKAs with cementless tibial components. Fifteen patients had tibial fractures after surgery. Anterior and posterior KCDs and fracture line origins were assessed using 3D-CT postoperatively. Proximal tibial morphology was assessed using the medial eminence line (MEL), which runs parallel to the tibial axis and passes through the tip of the medial intercondylar eminence of the tibia on long-leg anteroposterior radiograph. Knees had overhanging medial tibial condyle if the MEL passed medially to the medial tibial cortex. KCDs were compared between patients with/without fractures. Tibial component positions were evaluated, considering effects of tibial morphologies and component positions on fracture prevalence and KCDs. RESULTS: Fracture lines were found between the keel and posterior cortex in 12/15 patients. Posterior KCDs were significantly shorter in patients with fractures than in patients without (2.7 ± 1.6 mm vs 5.2 ± 1.7 mm, P < 0.001). Patients with medial overhanging condyles were more likely to have fracture (10/51 vs 5/166, P < 0.001) and had significantly shorter posterior KCD than those without (3.6 ± 1.5 mm vs 5.5 ± 1.8 mm, P < 0.001). Patients with tibial component that was set too medial, low, and valgus had higher rates of fracture than those without (7/39 vs 8/178, P = 0.008). Medial (r = 0.30, P < 0.001), low (r = -0.33, P < 0.001), and valgus implantations (r = 0.35, P < 0.001) of tibial components were related to shorter posterior KCDs. CONCLUSION: Short posterior KCD after OUKA is a risk factor for postoperative tibial fracture. Patients with either malposition of the tibial component (too medial, low, and valgus) and/or a medial overhanging condyle exhibit a shorter distance of posterior KCD and higher rate of fracture. LEVEL OF EVIDENCE: Level III.

Lateral osteoarthritis progression is associated with a postoperative residual tibiofemoral subluxation in Oxford UKA.

PURPOSE: Lateral compartment osteoarthritis progression (LOP) is a major complication after Oxford mobile-bearing unicompartmental knee arthroplasty (OUKA). This study aimed to identify the association between tibiofemoral subluxation (TFS) and LOP after OUKA. Patients whose TFS was uncorrectable according to preoperative stress radiographs were hypothesised to develop residual TFS even after surgery, and thought to be more likely to develop LOP. METHODS: The study included 201 patients who underwent medial OUKA. Fifteen patients showed increases in LOP of at least two Kellgren-Lawrence grades after surgery [progression (P) group], while the others had no progression (N group, n = 186). TFS was measured on preoperative full leg weight-bearing radiographs, valgus stress radiographs and postoperative plain radiographs. Valgus stress radiographs were obtained using a firm manual valgus force with the knee flexed at 20°. Leg alignment, Oxford knee score (OKS), and revision rates were assessed. RESULTS: The P group had significantly higher TFS values on preoperative valgus stress (6.8° ± 2.2° vs. 4.5° ± 2.0°; P < 0.001) and postoperative radiographs (6.6° ± 2.3° vs. 4.6° ± 2.9°; P < 0.001) than the N group. Patients with postoperative residual TFS and postoperative valgus alignment were more likely to have LOP, but 9 of the 15 LOP patients did not show postoperative valgus alignment. The P group had significantly poorer postoperative OKS (33.0 ± 10.2 vs. 37.4 ± 6.5, P = 0.017) and a higher rate of revision (6/15 vs 6/186; odds ratio = 19.16; 95% CI = 4.98-76.05, P < 0.001). CONCLUSION: OA progression in the lateral compartment after medial OUKA might be associated with postoperative residual TFS, but does not always coexist with postoperative valgus alignment. Preoperative assessment of TFS with valgus stress could be a potential predictor of postoperative residual TFS and LOP. LEVEL OF EVIDENCE: Level III.

Bearing Separation From the Lateral Wall of the Tibial Component Is a Risk of Anterior Dislocation of the Mobile Bearing in Oxford Unicompartmental Knee Arthroplasty.

BACKGROUND: Bearing dislocation is a serious complication after Oxford unicompartmental knee arthroplasty. Bearing separation from the lateral wall can cause it to spin (90° horizontal rotation) and eventually dislocate because there is just a 2 mm difference in height in both the lateral and medial sides from the bottom of the bearing, compared with the anterior (5 mm) and posterior (3 mm) sides. The details of this problem have not been previously examined. METHODS: Twenty-one dislocations in 12 patients were retrospectively analyzed. Bearing separation was defined as the bearing position being sufficiently distant from the lateral wall of the tibial component to allow spinning. We analyzed the incidence of separation, the direction and the recurrence of the dislocations, and their causes and treatments. RESULTS: Five of the 12 patients had separation. Of the total of 21 dislocations, 11 occurred in cases of separation (52%). Seven of 11 anterior dislocations were found to have separation, whereas nine of 13 posterior dislocations occurred without separation (P = .0237). Three of 5 patients with separation had recurrence of dislocation, and eventually 2 underwent revision to fixed-bearing unicompartmental knee arthroplasty. CONCLUSION: Bearing separation from the lateral wall of the tibial component can cause bearing dislocation, especially in an anterior direction. To prevent separation, the wall-bearing distance should be evaluated before the keel slot preparation, with manipulation as necessary. Conversely, posterior dislocation was predominant in our nonseparation cases.

Effectiveness of an accelerometer-based portable navigation for intraoperative adjustment of leg length discrepancy in total hip arthroplasty in the supine position.

BACKGROUND: This study aimed to examine the accuracy of the HipAlign® accelerometer-based portable navigation system by measuring the intraoperative leg length change of patients who underwent total hip arthroplasty (THA) and comparing the measured leg length discrepancy (LLD) determined by the navigation system and a freehand technique. METHODS: A total of 61 patients who underwent THA using the anterolateral approach in the supine position were included in this study and divided into two groups: those who underwent THA with navigation (Group N; N = 31) and with the freehand technique (Group F; N = 30). Statistical analyses were performed to compare the intraoperative leg length change, pre- and post-LLD, absolute values of post-LLD, and the number of patients with the postoperative LLD within 10 mm and 5 mm between the two groups. Additionally, we examined the correlation between the leg length change obtained through intraoperative navigation and measured from the radiographs. Moreover, to evaluate the navigation accuracy, we examined the correlation between the absolute error of leg length change and cup orientation. RESULTS: The postoperative LLD was significantly lower and the number of patients with the postoperative LLD within 5 mm was significantly higher in Group N, compared with Group F. Additionally, the amount of leg length change measured intraoperatively by the navigation system was strongly correlated with the values obtained by the postoperative radiographic measurement with a small absolute error and minimal wasted time. Moreover, a significant positive correlation was found between the absolute error of the leg length change and that of the cup inclination. CONCLUSIONS: Our study demonstrates that the accelerometer-based portable navigation system is useful for the intraoperative adjustment of leg length discrepancy during THA for patients in the supine position, as it provides good accuracy and minimizes required time for use.

Fully hydroxyapatite-coated compaction broached and triple-tapered stem may reduce the risk of stress shielding after primary total hip arthroplasty.

PURPOSE: Changes in bone mineral density (BMD) around the fully hydroxyapatite (HA)-coated compaction broached and triple-tapered stem, namely, Polarstem, after total hip arthroplasty (THA) are currently unknown. Therefore, the aims of this study were to investigate clinical outcomes of Polarstem, mainly postoperative temporal changes in BMD around the stem for 2 years, and to compare them with those of HA-coated and non-HA-coated tapered-wedge stems. METHODS: This retrospective cohort study enrolled 100 consecutive patients who underwent THA using Polarstem (n = 38), HA-coated Anthology (n = 31), and non-HA-coated Anthology (n = 31). BMD was evaluated using dual-energy X-ray absorptiometry in seven regions according to the Gruen zones. Postoperatively, BMD around the stem was assessed within 2 months (baseline BMD) and at 6, 12, and 24 months. A change in BMD was defined as the value calculated by dividing each postoperative BMD value at 6, 12, and 24 months by the baseline BMD value. Changes in BMD and radiographic parameters such as stress shielding and spot welds were compared among the three stems. RESULTS: The incidence rate of stress shielding in the Polarstem group was significantly lower than those in the other two groups (p = 0.007). The change in BMD in Zone 7 of Polarstem was significantly more than that of the other two groups at 12 and 24 months postoperatively (p = 0.030 and p = 0.009, respectively). CONCLUSION: Polarstem, a fully HA-coated compaction broached and triple-tapered stem, maintained BMD around the femoral calcar until 2 years postoperatively and could reduce the risk of stress shielding compared with tapered-wedge stems.

Anterior Cruciate Ligament Deficiency is Not Always a Contraindication for Medial Unicompartmental Knee Arthroplasty: A Retrospective Study in Nondesigner's Japanese Hospital.

BACKGROUND: An intact anterior cruciate ligament (ACL) is thought to be prerequisite for successful unicompartmental knee arthroplasty (UKA), but recent studies reported successful midterm results of UKA in ACL-deficient (ACLD) knees. We hypothesized that ACLD is not always a contraindication for medial UKA when preoperative radiographs showed typical anteromedial knee patterns. METHODS: From April 2012 to March 2016, 401 Oxford mobile-bearing UKAs in 282 patients were retrospectively identified from our database. Patients whose ACL was severely damaged, but preoperative X-rays showed typical anteromedial osteoarthritis patterns, were categorized into the ACLD group. From intraoperative data, those whose ACL was intact were categorized into the ACL functional (ACLF) group. There were 32 and 369 knees in the ACLD and ACLF groups, respectively, and mean follow-up periods were 66.1 and 63.8 months for the ACLD and ACLF groups, respectively. We compared the postoperative clinical outcome and component survivorship, with an endpoint of component revision, between ACLD groups and ACLF groups. RESULTS: In both groups, the Oxford knee score, Knee Society score, Tegner activity score, and knee range of motion in extension were improved after surgery. The UKA component survival rate at five years was 100% in the ACLD group and 98.9% in the ACLF group. There were no significant differences between the groups. CONCLUSION: Mid-term clinical outcomes of Oxford mobile-bearing UKA in ACLD knees were similar to those in ACLF knees. ACL deficiency is not always a contraindication for medial unicompartmental knee arthroplasty in patients with typical anteromedial osteoarthritis radiographs.

Intraoperative pelvic movement is associated with the body mass index in patients undergoing total hip arthroplasty in the supine position.

BACKGROUNDS: There are very few reports on pelvic movement during total hip arthroplasty (THA) in the supine position. We investigated intraoperative pelvic motion in the sagittal and axial planes to determine if preoperative clinical factors, including body mass index (BMI) affect intraoperative pelvic motion. METHODS: Fifty-three patients with osteoarthritis undergoing THA in the supine position were included. Clinical factors, such as age, BMI, and pelvic tilt were assessed preoperatively. Intraoperative pelvic motion in the axial and sagittal planes was assessed using a portable navigation system. We assessed the change in pelvic tilt from registration to cup implantation as the pelvic tilt change; positive values indicated anterior pelvic tilt. We measured the values and absolute values of changes in axial rotation from registration to cup implantation to determine the axial rotation angle. The effects of patient factors on pelvic motion (pelvic tilt change and axial rotation angle) were analyzed using a Spearman's correlation analysis. RESULTS: Preoperative pelvic tilt was negatively correlated with pelvic tilt change (r = -0.57, p < 0.05) and the absolute axial rotation angle (r = -0.57, p < 0.05). BMI and absolute axial rotation angle were negatively correlated (r = -0.54, p < 0.05). Age was not correlated with change in the pelvic tilt and the axial rotation angle. CONCLUSIONS: Preoperative pelvic tilt and BMI are important factors to determine intraoperative pelvic motion in patients who undergo THA in the supine position. This can help surgeons to preoperatively identify patients with a higher risk of intraoperative pelvic motion.

Evaluation of the accuracy of acetabular cup orientation using the accelerometer-based portable navigation system.

BACKGROUND: Accurate orientation of acetabular and femoral components is important during total hip arthroplasty (THA). In recent years, several navigation systems have been developed. However, these navigation systems for THA are unpopular worldwide because of their high cost. We assessed the orientation accuracy of cups inserted using a disposable accelerometer-based portable navigation system for THAs. METHODS: This was a prospective cohort study. We analyzed 63 hips with navigation prospectively and 30 hips without navigation retrospectively as historical control. The patients underwent THA via the mini anterolateral approach in the supine position using an accelerometer-based portable navigation system. We compared the preoperative target angles, intraoperative cup angles using navigation records, postoperative angles using postoperative CT data, measurement errors of cup angles, and clinical parameters such as sex, treated side, age at surgery, and body mass index (BMI). RESULTS: The average absolute error (postoperative CT-navigation record) was 2.7 ± 2.1° (inclination) and 2.7 ± 1.8° (anteversion), and the absolute error (postoperative CT-preoperative target angle) was 2.6 ± 1.9° (inclination) and 2.7 ± 2.2° (anteversion). The absolute error between postoperative CT and target angle with navigation was significantly lower than the error without navigation (inclination; p = 0.025, anteversion; p = 0.005). Cup malalignment (absolute difference of inclination or anteversion between postoperative CT and preoperative target angle of over 5°) was significantly associated with BMI value (OR: 1.3, 95% CI: 1.1-1.7). The absolute measurement error of cup inclination and anteversion was significantly correlated with patients' BMI (inclination error: correlation coefficient = 0.53, p < 0.001, anteversion error: correlation coefficient = 0.58, p < 0.001). CONCLUSIONS: The clinical accuracy of accelerometer-based portable navigation is precise for the orientation of cup placement, although accurate cup placement was affected by high BMI. This is the first study to report the accuracy of accelerometer-based portable navigation for THA in the supine position.

The tibial lateral axis is a novel extraarticular landmark for detection of the tibial anteroposterior axis.

PURPOSE: Although the tibial rotation axis is significant in knee arthroplasty, no reliable extraarticular landmark has been proposed. We hypothesized that the tibial lateral axis (TLA), a tangential line of the lateral tibial surface, is perpendicular to the surgical epicondylar axis (SEA) and compared it to other existing landmarks by 3D-CT. METHODS: Fifty legs in 25 consecutive patients were studied. Using their preoperative CT, the TLAs were identified on slices at 10-50% of the total length of the tibia and the measured differences of angles against the line perpendicular to the SEA (the tibial AP axis) were calculated. The differences between the SEA and the femoral and tibial posterior condylar axis, Akagi's line and the line between the medial intercondylar spine and the medial border of the patellar tendon (sAP line)(intraarticular), the ankle axis, and the transmalleolar axis (extraarticular) were also calculated and compared. RESULTS: The mean values of TLA at 10%, 20%, 30% were virtually parallel to the SEA (0.97° ± 4.84°, 0.02° ± 4.61°, 1.10° ± 4.97°, respectively). They were equivalent to existing intraarticular landmarks and superior to existing extraarticular landmarks, and these levels corresponded to the tip to the lower end of the tibial tubercle (at 10.8% and 17.0% of total tibial length). CONCLUSION: The proximal TLAs can be an extraarticular bony landmark that indicates the line perpendicular to the SEA. A prospective study is needed to prove the validity and accuracy of the axes clinically.

A subcutaneous arthroscopic portal closure technique without thread exposure.

We present a simple new suture technique for an arthroscopic portal that enables a secured subcutaneous suture without thread exposure. A curved suture needle is inserted through the skin at approximately 1 cm from the wound edge. The needle penetrates the subcutaneous tissue and exits through the skin on the opposite side of the wound edge. The needle and suture are pulled from just underneath the skin layer. The thread is collected within the wound, and the other end of the thread is pulled from the wound. The needle is inserted at just beneath the skin layer, penetrates the subcutaneous tissue, and pierces the opposite side of the skin. The needle is retrieved along with the thread at approximately 1 cm from the other side of the wound edge. After removing the needle from the thread, the thread passing in the wound is located and the needle side of the thread is retrieved from the wound. The ends of the thread are tied under the appropriate tension. From our findings, we recommend this method for suturing of all arthroscopic portals, as well as other small incisions that need water-tight suture.

Adequate Positioning of the Tibial Component Is Key to Avoiding Bearing Impingement in Oxford Unicompartmental Knee Arthroplasty.

BACKGROUND: Bearing dislocation is a serious complication of unicompartmental knee arthroplasty (UKA) with the Oxford knee prosthesis equipped with a mobile bearing. We aimed to clarify the extent of intraoperative movement of the mobile bearing and its relationship with the positioning of prosthesis components in patients undergoing Oxford UKA. METHODS: This retrospective study included 50 patients (50 knees) who underwent Oxford UKA for anteromedial osteoarthritis or osteonecrosis of the knee. Intraoperative bearing movement was assessed at various angles of knee flexion (0°, 30°, 60°, 90°, and 120°). We stratified patients according to the extent of bearing movement posteriorly during intraoperative knee flexion, with or without contacting the lateral wall of the tibial component (with contact, 20 knees; without contact, 30 knees). Postoperative radiographic evaluations were conducted at 1 week postoperatively to assess the positional parameters of the tibial and femoral components (varus/valgus alignment, rotation, mediolateral position). Clinical evaluations were conducted at 1 year postoperatively (maximum flexion angle, Oxford Knee Score). RESULTS: Abnormal intraoperative movement of the mobile bearing resulting in contact with the lateral wall of the tibial component was associated with a significantly more medial position and external rotation of the tibial component, as well as poorer improvement in knee flexion angle at 1 year postoperatively. CONCLUSION: In Oxford UKA recipients, the bearing may impinge on the lateral wall of the tibial component during flexion above 60° if the tibial component is placed too medially or exhibits pronounced external rotation, which may limit knee function improvement postoperatively.

Valgus Subsidence of the Tibial Component Caused by Tibial Component Malpositioning in Cementless Oxford Mobile-Bearing Unicompartmental Knee Arthroplasty.

BACKGROUND: Valgus subsidence (VS) of the tibial component is a rare complication of unicompartmental knee arthroplasty (UKA), and surgeons might consider revision surgery. The present study aimed to identify the factors related to VS of the tibial component after cementless Oxford mobile-bearing UKA. METHODS: The study included 120 patients who underwent Oxford mobile-bearing UKA using a cementless tibial component in our center between September 2015 and September 2016. Six showed VS of >2° after surgery. Patients were stratified into 2 groups according to the occurrence of VS of the tibial component (VS group, n = 6; no-subsidence group, n = 114). Postoperative radiographic evaluations were conducted to assess the varus/valgus alignment, rotation, and mediolateral position of the tibial and femoral components. The Oxford Knee Score (OKS) was assessed at 3, 6, and 12 months postoperatively. Positional parameters and sequential change in OKS were compared between the two groups using unpaired t-test (P < .05, statistically significant). RESULTS: At 3 months postoperatively, an average VS of 3.4° in the VS group was observed, with a significant decrease in OKS. VS was associated with a significantly more medial position and external rotation of the tibial component. After 3 months, VS stopped, and the OKS gradually improved without revision surgery. CONCLUSIONS: VS might be caused by the malpositioning of the tibial component. VS of the tibial component after UKA appears to stop, with simultaneous pain relief, even without revision after 3 months postoperatively.

Effect of tibial component position on short-term clinical outcome in Oxford mobile bearing unicompartmental knee arthroplasty.

BACKGROUND: Malposition of the tibial components is a well-known complication of unicompartmental knee arthroplasty. In this study, we aimed to ascertain the relationship between the tibial component position and clinical outcomes of unicompartmental knee arthroplasty. We focused on the tibial component height and obliquity in the coronal plane. METHODS: Patients with anteromedial osteoarthritis who underwent Oxford mobile-bearing unicompartmental knee arthroplasty (n = 45) were included, and their Oxford knee score was assessed prior to and 1 and 2 years following surgery. We also assessed the postoperative tibial component position in the coronal plane using radiography, measuring the tibial component height and obliquity. We analyzed the sequential change in both clinical scores using repeated measures analysis of variance (p < 0.05). The effects of tibial component position on the clinical outcomes were analyzed using linear regression analysis (p < 0.05). RESULTS: The Oxford knee score significantly improved 1 year after surgery. The tibial component height and obliquity had a significantly negative correlation with the 2-year postoperative Oxford knee score. They were also correlated significantly with Oxford knee score recovery after unicompartmental knee arthroplasty. CONCLUSION: The 2-year postoperative outcomes of Oxford unicompartmental knee arthroplasty depended on the tibial component position. We observed poorer outcomes when the tibial component was placed at a lower level relative to the lateral compartment and when there was an excessive valgus angle relative to the lower limb axis.