Structuring of perovskite-silicon tandem solar cells for reduced reflectance and thermalization losses.

Perovskite-silicon tandem solar cells have made rapid progress in the last decade. Still, they suffer from multiple loss channels, one of them being optical losses including reflection and thermalization. In this study, the effect of structures at the air-perovskite and perovskite-silicon interface of the tandem solar cell stack on these two loss channels are evaluated. Regarding reflectance, every structure evaluated led to a reduction relative to the optimized planar stack. The best combination of structures evaluated reduced the reflection loss from 3.1 mA/cm2 (planar reference) to 1.0 mA/cm2 equivalent current. Additionally, nanostructured interfaces can lead to a reduction in thermalization losses by enhancing the absorptance in the perovskite sub-cell close to the bandgap. This means that more current can be generated at a higher voltage under the assumption that current-matching is maintained and the perovskite bandgap is increased accordingly, pathing the way towards higher efficiencies. Here, the largest benefit was obtained using a structure at the upper interface. The best result yielded an increase of 4.9%rel in efficiency. A comparison to a tandem solar cell using a fully textured approach with random pyramids on silicon shows potential benefits for the suggested nanostructured approach regarding thermalization losses, while reflectance is reduced at a similar level. In addition, the applicability of the concept in the module context is shown.

Modeling of thin-film interference filters on structured substrates: microfacet-based BSDF versus ray tracing.

We compare two model approaches for the ray optical description of PV modules with coloring based on an interference layer system on the inside of the cover glass. The light scattering is described by a microfacet-based bidirectional scattering distribution function (BSDF) model on the one hand and ray tracing on the other hand. We show that the microfacet-based BSDF model is largely sufficient for the structures used in the context of the MorphoColor application. A structure inversion shows a significant influence only for extreme angles and very steep structures showing correlated heights and surface normal orientations. Regarding an angle-independent color appearance, the model-based comparison of possible module configurations shows a clear advantage of a structured layer system compared to planar interference layers in combination with a scattering structure on the front side of the glass.

Light trapping gratings for solar cells: an analytical period optimization approach.

Solar cells can harvest incident sunlight very efficiently by utilizing grating-based light trapping. As the working principle of such gratings strongly depends on the number as well as the propagation directions of the diffraction orders, the grating period is a key parameter. We present an analytical model for optimizing the grating period, focusing on its impact on light path enhancement and outcoupling probability. Based on the presented model, we formulate guidelines to maximize light trapping in state-of-the-art high-end solar cells. The model increases the understanding of the grating performance in systems like the III-V//Si triple junction solar cell achieving record efficiency.

Modeling the optical properties of Morpho-inspired thin-film interference filters on structured surfaces.

We present a method for modeling the optical properties of interference layer systems on structured surfaces as used in the MorphoColor technology for coloring integrated photovoltaic modules. By combining a microfacet-based bidirectional scattering distribution function model with a transfer matrix formalism, we can simulate the spectrally resolved reflection and transmission properties of the system in good agreement with measurement data. To consider the MorphoColor technology in an overall optical system and compare the application on the front side of the module glass with the application in the composite, the model is additionally combined with a formalism called Optical Properties of Textured Optical Sheets. For a representative illumination and viewing geometry, the composite configuration causes a significantly improved homogeneity of the color appearance.

Optimizing metal grating back reflectors for III-V-on-silicon multijunction solar cells.

Multi-junction solar cells allow to utilize sunlight more effectively than single junction solar cells. In this work, we present optical simulations of III-V-on-silicon solar cells with a metal grating at the back, which experimentally have reached more than 33% power conversion efficiency. First, we perform simulations with the finite element method and compare them with experimental data to validate our model. We find that accurately modeling the investigated geometrical structure is necessary for best agreement between simulation and experimental measurements. Then, we optimize the grating for maximized light trapping using a computationally efficient Bayesian optimization algorithm. The photo current density of the limiting silicon bottom cell is improved from 13.48 mA/cm2 for the experimental grating to 13.85 mA/cm2 for the optimized metal grating. Investigation of all geometrical optimization parameters of the grating (period, height,…) shows that the structure is most sensitive towards the period, a parameter highly controllable in manufacturing by inference lithography. The results show a pathway to exceed the current world record efficiency of the III-V-on-silicon solar cell technology.

Tailored disorder: a self-organized photonic contact for light trapping in silicon-based tandem solar cells.

We present a process development leading to efficient rear side light trapping structures with the purpose of enhancing the infrared response of a silicon-based tandem solar cell. To this end, we make use of phase separation effects of two immiscible polymers, polystyrene and poly(methyl methacrylate), resulting in a non-periodic polystyrene structure on silicon with a well-defined size distribution. Onto this pattern, we evaporate silver as a scattering rear side mirror and contact layer. Average feature sizes and periods can be tuned by varying material properties (e.g. molar weights or ratios of the polymers) as well as processing conditions during the spin coating. This way a favorable pseudo period of approx. 1 µm for these disordered structure features was realized and successfully implemented into a silicon solar cell. The structure shows a ring-shaped scattering distribution which is beneficial for light trapping in solar cells. External quantum efficiency measurements show that a gain in short circuit current density of 1.1 mA/cm2 compared to a planar reference can be achieved, which is in the same range as we achieved using nanoimprint lithography in a record triple-junction III/V on a silicon device.

Broadband antireflection Mie scatterers revisited-a solar cell and module analysis.

Reflectance, reduction, and light trapping enhancement are essential to maximize the absorption of silicon solar cells. The industrial state of the art method to improve the solar cell optics is wet chemical texturization of the front surface in combination with the deposition of antireflection coatings. This work analyzes an alternative route, namely a TiO2 pillar structure on the front side of a planar silicon solar cell encapsulated in ethylene vinyl acetate (EVA) and glass. It focuses on parameter variations of the structured TiO2 layer while taking the module encapsulation into account. It is shown that internal reflections at the front interface of the module play a crucial role for the structure design. This leads to optimized structures working in a different optical regime. While state of the art structures optimized for a half infinite encapsulation act as effective media, structures optimized for the full module show an improved performance by making use of diffractive effects. It could be shown that weighted reflectance of 4.7% can be reached for a solar module with TiO2 pillar structure on top of the silicon surface compared to 5.5% for a two-layer ARC with a TiO2 bottom layer and 2.3% for an isotexture, which is the state of the art structure for multicrystalline silicon cells.

Theoretical study of pyramid sizes and scattering effects in silicon photovoltaic module stacks.

Front side pyramids are the industrial standard for wafer based monocrystalline silicon solar cells. These pyramids fulfill two tasks: They act as anti-reflective structure on the one hand and as a light-trapping structure on the other hand. In recent development smaller pyramids with sizes below 1 µm attract more and more interest. In this paper an optical analysis of periodically arranged front side pyramids is performed. The impact on the reflectance as well as on the useful absorption within the solar cell is investigated depending on the pyramids size, the amount of additional scattering in the system and the quality of the rear side reflector. In contrast to other investigations not only the solar cell, but the full photovoltaic (PV) module stack is considered. This can strongly influence results, as we show in this paper. The results indicate that in a PV module stack with realistic assumptions for the amount of scattering as well as for the rear side reflectance only small differences for pyramids with sizes above 600 nm occur. Preliminary conclusions for random pyramids deduced from these results for periodically arranged pyramids indicate that these differences could become even smaller.

Optical modeling of structured silicon-based tandem solar cells and module stacks.

Silicon-based tandem solar cells and modules are complex systems that require optical modeling for the optimization towards highest efficiencies. The fact that such devices typically incorporate surface structures of different optical regimes poses high requirements to the involved simulation tools. The OPTOS formalism is ideally suited to deal with such complexity. Within this work OPTOS is extended in order to calculate the layer resolved absorptance in silicon-based tandem solar cells and module stacks. After describing the relevant mathematical details, a good agreement between OPTOS absorptance simulation results and EQE measurements of the current 33.3% record efficiency III-V on silicon two-terminal tandem solar cell is found. Furthermore, a detailed loss analysis is performed for an exemplary perovskite silicon solar cell with and without module encapsulation. The comparison reveals a lower photocurrent density for the module stack due to increased reflectance and absorption in the EVA.

Optical analysis of a III-V-nanowire-array-on-Si dual junction solar cell.

A tandem solar cell consisting of a III-V nanowire subcell on top of a planar Si subcell is a promising candidate for next generation photovoltaics due to the potential for high efficiency. However, for success with such applications, the geometry of the system must be optimized for absorption of sunlight. Here, we consider this absorption through optics modeling. Similarly, as for a bulk dual-junction tandem system on a silicon bottom cell, a bandgap of approximately 1.7 eV is optimum for the nanowire top cell. First, we consider a simplified system of bare, uncoated III-V nanowires on the silicon substrate and optimize the absorption in the nanowires. We find that an optimum absorption in 2000 nm long nanowires is reached for a dense array of approximately 15 nanowires per square micrometer. However, when we coat such an array with a conformal indium tin oxide (ITO) top contact layer, a substantial absorption loss occurs in the ITO. This ITO could absorb 37% of the low energy photons intended for the silicon subcell. By moving to a design with a 50 nm thick, planarized ITO top layer, we can reduce this ITO absorption to 5%. However, such a planarized design introduces additional reflection losses. We show that these reflection losses can be reduced with a 100 nm thick SiO2 anti-reflection coating on top of the ITO layer. When we at the same time include a Si3N4 layer with a thickness of 90 nm on the silicon surface between the nanowires, we can reduce the average reflection loss of the silicon cell from 17% to 4%. Finally, we show that different approximate models for the absorption in the silicon substrate can lead to a 15% variation in the estimated photocurrent density in the silicon subcell.

Optical simulation of photovoltaic modules with multiple textured interfaces using the matrix-based formalism OPTOS.

The OPTOS formalism is a matrix-based approach to determine the optical properties of textured optical sheets. It is extended within this work to enable the modelling of systems with an arbitrary number of textured, plane-parallel interfaces. A matrix-based system description is derived that accounts for the optical reflection and transmission interaction between all textured interfaces. Using OPTOS, we calculate reflectance and absorptance of complete photovoltaic module stacks, which consist of encapsulated silicon solar cells featuring textures that operate in different optical regimes. As exemplary systems, solar cells with and without module encapsulation are shown to exhibit a considerable absorptance gain if the random pyramid front side texture is combined with a diffractive rear side grating. A variation of the sunlight's angle of incidence reveals that the grating gain is almost not affected for incoming polar angles up to 60°. Considering as well the good agreement with alternative simulation techniques, OPTOS is demonstrated to be a versatile and efficient method for the optical analysis of photovoltaic modules.

Wave optical simulation of the light trapping properties of black silicon surface textures.

Due to their low reflectivity and effective light trapping properties black silicon nanostructured surfaces are promising front side structures for thin crystalline silicon solar cells. For further optimization of the light trapping effect, particularly in combination with rear side structures, it is necessary to simulate the optical properties of black silicon. Especially, the angular distribution of light in the silicon bulk after passage through the front side structure is relevant. In this paper, a rigorous coupled wave analysis of black silicon is presented, where the black silicon needle shaped structure is approximated by a randomized cone structure. The simulated absorptance agrees well with measurement data. Furthermore, the simulated angular light distribution within the silicon bulk shows that about 70% of the light can be subjected to internal reflection, highlighting the good light trapping properties.

Matrix formalism for light propagation and absorption in thick textured optical sheets.

In this paper, we introduce a simulation formalism for determining the Optical Properties of Textured Optical Sheets (OPTOS). Our matrix-based method allows for the computationally-efficient calculation of non-coherent light propagation and absorption in thick textured sheets, especially solar cells, featuring different textures on front and rear side that may operate in different optical regimes. Within the simulated system, the angular power distribution is represented by a vector. This light distribution is modified by interaction with the surfaces of the textured sheets, which are described by redistribution matrices. These matrices can be calculated for each individual surface texture with the most appropriate technique. Depending on the feature size of the texture, for example, either ray- or wave-optical methods can be used. The comparison of the simulated absorption in a sheet of silicon for a variety of surface textures, both with the results from other simulation techniques and experimentally measured data, shows very good agreement. To demonstrate the versatility of this newly-developed approach, the absorption in silicon sheets with a large-scale structure (V-grooves) at the front side and a small-scale structure (diffraction grating) at the rear side is calculated. Moreover, with minimal computational effort, a thickness parameter variation is performed.

3D optical simulation formalism OPTOS for textured silicon solar cells.

In this paper we introduce the three-dimensional formulation of the OPTOS formalism, a matrix-based method that allows for the efficient simulation of non-coherent light propagation and absorption in thick textured sheets. As application examples, we calculate the absorptance of solar cells featuring textures on front and rear side with different feature sizes operating in different optical regimes. A discretization of polar and azimuth angle enables a three-dimensional description of systems with arbitrary surface textures. We present redistribution matrices for 3D surface textures, including pyramidal textures, binary crossed gratings and a Lambertian scatterer. The results of the OPTOS simulations for silicon sheets with different combinations of these surfaces are in accordance with both optical measurements and results based on established simulation methods like ray tracing. Using OPTOS, we show that the integration of a diffractive grating at the rear side of a silicon solar cell featuring a pyramidal front side results in absorption close to the Yablonovitch Limit enhancing the photocurrent density by 0.6 mA/cm2 for a 200 µm thick cell.

Staufen-1 interacts with the human endogenous retrovirus family HERV-K(HML-2) rec and gag proteins and increases virion production.

The human endogenous retrovirus family HERV-K(HML-2) Rec protein is an RNA transport factor that enhances nuclear export of intron-containing retroviral transcripts. Using the yeast two-hybrid approach, we have newly identified human Staufen-1 as a Rec-interacting protein. The interaction was confirmed by coimmunoprecipitation experiments, and the relevant site in Staufen-1 has been mapped to double-stranded RNA binding domain 4 (RBD4). Staufen-1 is in several aspects functionally related to retroviral RNA transport proteins. It binds mRNAs and targets its ribonuclear cargo to polysomes for efficient translation. We observed an accumulation of Staufen-1 in the nucleus of Rec-expressing cells and colocalization in the nucleoli as well as in the cytoplasm. Overexpression of Staufen-1 resulted in a 5-fold enhancement in nuclear export and/or translation of unspliced HERV-K(HML-2) viral RNAs in the presence of Rec and its Rec-responsive element (RcRE) binding site together with a clear increase in virus production. Staufen-1 was previously shown to interact with the Gag protein of HIV-1, promoting Gag oligomerization and RNA encapsidation. We demonstrate here that Staufen-1 also binds to the Gag protein of HERV-K(HML-2). Under stress conditions, Rec colocalizes with Staufen-1 in stress granules in cells that express viral RNA but not in mRNA-decay-related processing bodies. Our results suggest a new role for Staufen-1 as a cellular Rec and HERV-K(HML-2) Gag cofactor.

Maximal power output by solar cells with angular confinement.

Angularly selective filters can increase the efficiency of radiatively limited solar cells. A restriction of the acceptance angle is linked to the kind of utilizable solar spectrum (global or direct radiation). This has to be considered when calculating the potential enhancement of both the efficiency and the power output. In this paper, different concepts to realize angularly selective filters are compared regarding their limits for efficiency and power output per unit area. First experimental results of a promising system based on a thin-film filter as the angularly selective element are given to demonstrate the practical relevance of such systems.

Nanopatterned Back-Reflector with Engineered Near-Field/Far-Field Light Scattering for Enhanced Light Trapping in Silicon-Based Multijunction Solar Cells.

Multijunction solar cells provide a path to overcome the efficiency limits of standard silicon solar cells by harvesting a broader range of the solar spectrum more efficiently. However, Si-based multijunction architectures are hindered by incomplete harvesting in the near-infrared (near-IR) spectral range as Si subcells have weak absorption close to the band gap. Here, we introduce an integrated near-field/far-field light trapping scheme to enhance the efficiency of silicon-based multijunction solar cells in the near-IR range. To achieve this, we design a nanopatterned diffractive silver back-reflector featuring a scattering matrix that optimizes trapping of multiply scattered light into a range of diffraction angles. We minimize reflection to the zeroth order and parasitic plasmonic absorption in silver by engineering destructive interference in the patterned back-contact. Numerical and experimental assessment of the optimal design on the performance of single-junction Si TOPCon solar cells highlights an improved external quantum efficiency over a planar back-reflector (+1.52 mA/cm2). Nanopatterned metagrating back-reflectors are fabricated on GaInP/GaInAsP//Si two-terminal triple-junction solar cells via substrate conformal imprint lithography and characterized optically and electronically, demonstrating a power conversion efficiency improvement of +0.9%abs over the planar reference. Overall, our work demonstrates the potential of nanophotonic light trapping for enhancing the efficiency of silicon-based multijunction solar cells, paving the way for more efficient and sustainable solar energy technologies.

Mask and plate: a scalable front metallization with low-cost potential for III-V-based tandem solar cells enabling 31.6 % conversion efficiency.

Low-cost approaches for mass production of III-V-based photovoltaics are highly desired today. For the first time, this work presents industrially relevant mask and plate for front metallization of III-V-based solar cells replacing expensive photolithography. Metal contacts are fabricated by nickel (Ni) electroplating directly onto the solar cell's front using a precisely structured mask. Inkjet printing offers low-cost and high-precision processing for application of an appropriate plating resist. It covers the solar cell's front side with narrow openings for subsequent electroplating. The width of the resulting Ni contacts is as low as (10.5 ± 0.8) µm with sharp edges and homogenous shape. The 4 cm2-sized champion III-V-on-silicon triple-junction solar cell with mask and plate front metallization reaches a certified conversion efficiency η of (31.6 ± 1.1) % (AM1.5 g spectrum). It performs just as well as the reference sample with photolithography-structured evaporated front contacts, which reaches η = (31.4 ± 1.1) %.

Gene Gun Her2/neu DNA Vaccination: Evaluation of Vaccine Efficacy in a Syngeneic Her2/neu Mouse Tumor Model.

Genetic vaccination using naked plasmid DNA is an immunization strategy both against infectious diseases and cancer.In order to improve efficacy of DNA vaccines, particularly in large animals and humans, different strategies have been pursued. These vaccination strategies are based on different application routes, schedules and coexpression of immunomodulatory molecules as adjuvants. Our mouse tumor model offers the possibility to investigate Her2/neu DNA vaccines in different settings, that is, intramuscular or intradermal application with or without coexpression of adjuvants. The immunogenicity of predicted peptides for Her2/neu specific memory T cells were screened and confirmed after intramuscular and intradermal application. Protection from tumor growth in tumor challenge experiments and both T cell and humoral immune responses against Her2/neu peptides are used as surrogate parameters for vaccine efficacy.

Nanopatterning of Perovskite Thin Films for Enhanced and Directional Light Emission.

Lead-halide perovskites offer excellent properties for lighting and display applications. Nanopatterning perovskite films could enable perovskite-based devices with designer properties, increasing their performance and adding novel functionalities. We demonstrate the potential of nanopatterning for achieving light emission of a perovskite film into a specific angular range by introducing periodic sol-gel structures between the injection and emissive layer by using substrate conformal imprint lithography (SCIL). Structural and optical characterization reveals that the emission is funnelled into a well-defined angular range by optical resonances, while the emission wavelength and the structural properties of the perovskite film are preserved. The results demonstrate a flexible and scalable approach to the patterning of perovskite layers, paving the way toward perovskite LEDs with designer angular emission patterns.