Fluorescence-encoded poly(methyl metharcylate) nanoparticles for a lateral flow assay detecting IgM autoantibodies in rheumatoid arthritis.

Rheumatoid arthritis (RA) belongs to the most often occurring autoimmune diseases in the world. For serological diagnosis, IgM auto-antibodies directed against the Fc portion of IgG referred to as rheumatoid factor are used as biomarkers. The autoantibody detection is usually done by ELISA. Such assays are reliable but are not suitable for point-of-care testing in contrast to lateral flow assays. Here, we report the development of a lateral flow assay based on carboxylated fluorescence-encoded poly(methyl methacrylate) nanoparticles. Poly(methyl methacrylate) is a non-toxic plastic with an excellent biocompatibility and high optical transparency which promises especially high sensitive fluorescence detection thereby leading to very sensitive assays. We could detect a positive signal in samples with a nephelometric reading down to 0.4 U/mL. By analyzing 30 sera of patients with a RA diagnosis and 34 sera of healthy test subjects we could confirm positive ELISA results in 72% of all cases and negative ELISA results in 97% of all cases.

Spatial Separation of Microbeads into Detection Levels by a Bioorthogonal Porous Hydrogel for Size-Selective Analysis and Increased Multiplexity.

Multiplex detection techniques are emerging within the fields of life science research and medical diagnostics where it is mandatory to analyze a great number of molecules. The detection techniques need to be highly efficient but often involve complicated and expensive fabrication procedures. Here, we present the immobilization and geometric separation of fluorescence-labeled microbeads for a multiplex detection in k levels. A compound of differently sized target molecules (DNA, proteins) is channeled into the respective detection levels by making use of a hydrogel as a size selective filter. The immobilized microbeads (10-20 µm) are considerably larger than the pores of the hydrogel network and therefore stay fixed at the well bottom and in higher elevations, respectively. Small biomolecules can diffuse through the pores of the network, whereas medium-sized biomolecules pass slower and large molecules will be excluded. Besides filtering, this method discriminates the used microbeads into k levels and thereby introduces a geometric multiplexity. Additionally, the exclusion of large entities enables the simultaneous detection of two target molecules, which exhibit the same affinity interaction. The hydrogel is formed through the combination of two macromonomers. One component is a homobifunctional polyethylene glycol linker, carrying a strained alkyne (PEG-BCN) and the second component is the azide-functionalized dendritic polyglycerol (dPG-N3). They react via the bioorthogonal strain-promoted azide alkyne cycloaddition (SPAAC). The hydrogel creates a solution-like environment for the diffusion of the investigated biomolecules all the while providing a stable, bioinert, and surface bound network.

Quantification of Aldehydes on Polymeric Microbead Surfaces via Catch and Release of Reporter Chromophores.

Aldehyde moieties on 2D-supports or micro- and nanoparticles can function as anchor groups for the attachment of biomolecules or as reversible binding sites for proteins on cell surfaces. The use of aldehyde-based materials in bioanalytical and medical settings calls for reliable methods to detect and quantify this functionality. We report here on a versatile concept to quantify the accessible aldehyde moieties on particle surfaces through the specific binding and subsequent release of small reporter molecules such as fluorescent dyes and nonfluorescent chromophores utilizing acylhydrazone formation as a reversible covalent labeling strategy. This is representatively demonstrated for a set of polymer microparticles with different aldehyde labeling densities. Excess reporter molecules can be easily removed by washing, eliminating inaccuracies caused by unspecific adsorption to hydrophobic surfaces. Cleavage of hydrazones at acidic pH assisted by a carbonyl trap releases the fluorescent reporters rapidly and quasi-quantitatively and allows for their fluorometric detection at low concentration. Importantly, this strategy separates the signal-generating molecules from the bead surface. This circumvents common issues associated with light scattering and signal distortions that are caused by binding-induced changes in reporter fluorescence as well as quenching dye-dye interactions on crowded particle surfaces. In addition, we demonstrate that the release of a nonfluorescent chromophore via disulfide cleavage and subsequent quantification by absorption spectroscopy gives comparable results, verifying that both assays are capable of rapid and sensitive quantification of aldehydes on microbead surfaces. These strategies enable a quantitative comparison of bead batches with different functionalization densities, and a qualitative prediction of their coupling efficiencies in bioconjugations, as demonstrated in reductive amination reactions with Streptavidin.

Switchable Oligo(glycidyl ether) Acrylate Bottlebrushes "Grafted-from" Polystyrene Surfaces: A Versatile Strategy toward Functional Cell Culture Substrates.

Thermoresponsive brushes based on linear poly(glycidyl ether)s (PGEs) have already shown to be functional coatings for cell sheet fabrication. In here, we introduce a method to functionalize polystyrene (PS) tissue culture substrates with thermoresponsive coatings comprising glycidyl ether-based bottlebrush architectures. Utilizing the UV-induced "grafting-from" approach, thermoresponsive oligo(glycidyl ether) acrylate (OGEA) macromonomers were polymerized from PS substrates under bulk conditions. Applying ellipsometry, water contact angle (CA), and atomic force microscopy (AFM) measurements, we found that OGEA coatings exhibit a complex, gel-like structure comprising nanosized roughness and exhibit a temperature-dependent phase transition in water through the reversible hydration of OGEA bottlebrush side chains. To assess the utility of the coatings as functional substrates for cell sheet fabrication, human dermal fibroblast (HDF) adhesion and detachment were investigated. By adjusting the bottlebrush properties via the grafting procedure and coating structure, we were able to harvest confluent HDF sheets from functionalized PS substrates in a temperature-triggered, controlled manner. As the first report on surface-grafted bottlebrushes comprising thermoresponsive side chains with molecular weight of up to 1 kDa, this study demonstrates the potential of OGEA-based coatings for cell sheet fabrication.

En route to traceable reference standards for surface group quantifications by XPS, NMR and fluorescence spectroscopy.

The fluorine content of polymer particles labelled with 2,2,2-trifluoroethylamine was reliably quantified with overlapping sensitivity ranges by XPS and solid-state NMR. This provides a first step towards reference materials for the metrological traceability of surface group quantifications. The extension of this concept to fluorescence spectroscopy is illustrated.

Scope and limitations of surface functional group quantification methods: exploratory study with poly(acrylic acid)-grafted micro- and nanoparticles.

The amount of grafted poly(acrylic acid) on poly(methyl methacrylate) micro- and nanoparticles was quantified by conductometry, (13)C solid-state NMR, fluorophore labeling, a supramolecular assay based on high-affinity binding of cucurbit[7]uril, and two colorimetric assays based on toluidine blue and nickel complexation by pyrocatechol violet. The methods were thoroughly validated and compared with respect to reproducibility, sensitivity, and ease of use. The results demonstrate that only a small but constant fraction of the surface functional groups is accessible to covalent surface derivatization independently of the total number of surface functional groups, and different contributing factors are discussed that determine the number of probe molecules which can be bound to the polymer surface. The fluorophore labeling approach was modified to exclude artifacts due to fluorescence quenching, but absolute quantum yield measurements still indicate a major uncertainty in routine fluorescence-based surface group quantifications, which is directly relevant for biochemical assays and medical diagnostics. Comparison with results from protein labeling with streptavidin suggests a porous network of poly(acrylic acid) chains on the particle surface, which allows diffusion of small molecules (cutoff between 1.6 and 6.5 nm) into the network.

A multiparametric fluorescence assay for screening aptamer-protein interactions based on microbeads.

For improving aptamer-ligand binding we have developed a screening system that defines optimal binding buffer composition. Using multiplex assays, one buffer system is needed which guarantees the specific binding of all aptamers. We investigated nine peer-reviewed DNA aptamers. Non-specific binding of aptamers is an obstacle. To address this, we investigated 16 proteins as specificity controls bound covalently to encoded microbeads in a multiplex assay. Increasing the NaCl concentration decreased the binding for all aptamers. Changing pH values by one unit higher or lower did not influence the aptamer binding significantly. However, pH < 5 led to non-specific binding for all aptamers. The PfLDH-aptamer selected in the absence of divalent cations exhibited doubling of its binding signal by the addition of Ca2+ and Mg2+. We confirmed Ca2+ and Mg2+ dependency of the aptamers for streptavidin and thrombin by observing a 90% and 50% binding decrease, respectively. We also achieved a doubling of binding for the streptavidin aptamer when replacing Ca2+ and Mg2+ by Mn2+. A buffer suitable for all aptamers can have considerable variations in pH or ionic strength, but divalent cations (Ca2+, Mg2+, Mn2+) are essential.

Simple colorimetric method for quantification of surface carboxy groups on polymer particles.

We present a novel, simple, and fast colorimetric method to quantify the total number of carboxy groups on polymer microparticle and nanoparticle surfaces. This method exploits that small divalent transition metal cations (M(2+) = Ni(2+), Co(2+), Cd(2+)) are efficiently bound to these surface functional groups, which allows their extraction by a single centrifugation step. Remaining M(2+) in the supernatant is subsequently quantified spectrophotometrically after addition of the metal ion indicator pyrocatechol violet, for which Ni(2+) was identified to be the most suitable transition metal cation. We demonstrate that the difference between added and detected M(2+) is nicely correlated to the number of surface carboxy groups as determined by conductometry, thereby affording a validated measure for the trueness of this procedure. The variation coefficient of ~5% found in reproducibility studies underlines the potential of this novel method that can find conceivable applications for the characterization of different types of poly(carboxylic acid)-functionalized materials, e.g., for quality control by manufacturers of such materials.

Hydrogels and Their Role in Biosensing Applications.

Hydrogels play an important role in the field of biomedical research and diagnostic medicine. They are emerging as a powerful tool in the context of bioanalytical assays and biosensing. In this context, this review gives an overview of different hydrogels and the role they adopt in a range of applications. Not only are hydrogels beneficial for the immobilization and embedding of biomolecules, but they are also used as responsive material, as wearable devices, or as functional material. In particular, the scientific and technical progress during the last decade is discussed. The newest hydrogel types, their synthesis, and many applications are presented. Advantages and performance improvements are described, along with their limitations.

Lifetime encoding in flow cytometry for bead-based sensing of biomolecular interaction.

To demonstrate the potential of time-resolved flow cytometry (FCM) for bioanalysis, clinical diagnostics, and optically encoded bead-based assays, we performed a proof-of-principle study to detect biomolecular interactions utilizing fluorescence lifetime (LT)-encoded micron-sized polymer beads bearing target-specific bioligands and a recently developed prototype lifetime flow cytometer (LT-FCM setup). This instrument is equipped with a single excitation light source and different fluorescence detectors, one operated in the photon-counting mode for time-resolved measurements of fluorescence decays and three detectors for conventional intensity measurements in different spectral windows. First, discrimination of bead-bound biomolecules was demonstrated in the time domain exemplarily for two targets, Streptavidin (SAv) and the tumor marker human chorionic gonadotropin (HCG). In a second step, the determination of biomolecule concentration levels was addressed representatively for the inflammation-related biomarker tumor necrosis factor (TNF-α) utilizing fluorescence intensity measurements in a second channel of the LT-FCM instrument. Our results underline the applicability of LT-FCM in the time domain for measurements of biomolecular interactions in suspension assays. In the future, the combination of spectral and LT encoding and multiplexing and the expansion of the time scale from the lower nanosecond range to the longer nanosecond and the microsecond region is expected to provide many distinguishable codes. This enables an increasing degree of multiplexing which could be attractive for high throughput screening applications.

Bioorthogonal in Situ Hydrogels Based on Polyether Polyols for New Biosensor Materials with High Sensitivity.

Both noncovalent and covalent encapsulations of active biomolecules, for example, proteins and oligonucleotides, for a new biosensor matrix in an in situ bioorthogonal hydrogel formation via a strain-promoted azide-alkyne cycloaddition reaction were investigated. Unspecific interaction between the gel and the biomolecules as well as protein denaturation was prevented by the bioorthogonal gel components, which ensure a uniform aqueous environment in the hydrogel network. No leaching of the active biomolecules was observed. Additionally, a much higher and also adjustable loading of biomolecules in the hydrogel matrix was achieved compared to conventional biosensor surfaces, where the sensor molecules are immobilized on monolayers (2D surfaces) or brushlike structures (3D surfaces). Spotting experiments of the hydrogel confirm the possibility to use this new surface for microarray-based multiplex applications which require very high signal-to-noise ratios.

Precise supramolecular control of surface coverage densities on polymer micro- and nanoparticles.

We report herein the controlled surface functionalization of micro- and nanoparticles by supramolecular host-guest interactions. Our idea is to exploit the competition of two high-affinity guests for binding to the surface-bound supramolecular host cucurbit[7]uril (CB7). To establish our strategy, surface azide groups were introduced to hard-sphere (poly)methylmethacrylate particles with a grafted layer of poly(acrylic acid), and a propargyl derivative of CB7 was coupled to the surface by click chemistry. The amount of surface-bound CB7 was quantified with the high-affinity guest aminomethyladamantane (AMADA), which revealed CB7 surface coverage densities around 0.3 nmol cm-2 indicative of a 3D layer of CB7 binding sites on the surface. The potential for surface functionalization was demonstrated with an aminoadamantane-labeled rhodamine (Ada-Rho) as a second high-affinity guest. Simultaneous incubation of CB7-functionalized particles with both high-affinity guests, AMADA and Ada-Rho, revealed a simple linear relationship between the resulting surface coverage densities of the model fluorescent dye and the mole fraction of Ada-Rho in the incubation mixture. This suggests a highly modular supramolecular strategy for the stable immobilization of application-relevant molecules on particle surfaces and a precise control of their surface coverage densities.

Quantification of surface functional groups on polymer microspheres by supramolecular host-guest interactions.

We introduce a method to determine the number of accessible functional groups on a polymer microsphere surface based on the interaction between the macrocyclic host cucurbit[7]uril (CB7) and a guest reacted to the microsphere surface. After centrifugation, CB7 in the supernatant is quantified by addition of a fluorescent dye. The difference between added and detected CB7 affords the number of accessible surface functional groups.