Highly Sensitive, Robust, and Recyclable TiO2/AgNP Substrate for SERS Detection.

Label-free biosensors provide an important platform for detecting chemical and biological substances without needing extra labeling agents. Unlike surface-based techniques such as surface plasmon resonance (SPR), interference, and ellipsometry, surface-enhanced Raman spectroscopy (SERS) possesses the advantage of monitoring analytes both on surfaces and in solutions. Increasing the SERS enhancement is crucial to preparing high-quality substrates without quickly losing their stability, sensitivity, and repeatability. However, fabrication methods based on wet chemistry, nanoimprint lithography, spark discharge, and laser ablation have drawbacks of waste of time, complicated processes, or nonreproducibility in surface topography. This study reports the preparation of recyclable TiO2/Ag nanoparticle (AgNP) substrates by using simple arc ion plating and direct-current (dc) magnetron sputtering technologies. The deposited anatase-phased TiO2 ensured the photocatalytic degradation of analytes. By measuring the Raman spectra of rhodamine 6G (R6G) in titrated concentrations, a limit of detection (LOD) of 10-8 M and a SERS enhancement factor (EF) of 1.01 × 109 were attained. Self-cleaning was performed via UV irradiation, and recyclability was achieved after at least five cycles of detection and degradation. The proposed TiO2/AgNP substrates have the potential to serve as eco-friendly SERS enhancers for label-free detection of various chemical and biological substances.

Use Microfluidic Chips to Study the Phototaxis of Lung Cancer Cells.

Cell migration is an important process involved in wound healing, tissue development, and so on. Many studies have been conducted to explore how certain chemicals and electric fields induce cell movements in specific directions, which are phenomena termed chemotaxis and electrotaxis, respectively. However, phototaxis, the directional migration of cells or organisms toward or away from light, is rarely investigated due to the difficulty of generating a precise and controllable light gradient. In this study, we designed and fabricated a microfluidic chip for simultaneously culturing cells and generating a blue light gradient for guiding cell migration. A concentration gradient was first established inside this chip, and by illuminating it with a blue light-emitting diode (LED), a blue light gradient was generated underneath. Cell migration in response to this light stimulus was observed. It was found that lung cancer cells migrated to the dark side of the gradient, and the intracellular reactive oxygen species (ROS) was proportional to the intensity of the blue light.

Studying Electrotaxis in Microfluidic Devices.

Collective cell migration is important in various physiological processes such as morphogenesis, cancer metastasis and cell regeneration. Such migration can be induced and guided by different chemical and physical cues. Electrotaxis, referring to the directional migration of adherent cells under stimulus of electric fields, is believed to be highly involved in the wound-healing process. Electrotactic experiments are conventionally conducted in Petri dishes or cover glasses wherein cells are cultured and electric fields are applied. However, these devices suffer from evaporation of the culture medium, non-uniformity of electric fields and low throughput. To overcome these drawbacks, micro-fabricated devices composed of micro-channels and fluidic components have lately been applied to electrotactic studies. Microfluidic devices are capable of providing cells with a precise micro-environment including pH, nutrition, temperature and various stimuli. Therefore, with the advantages of reduced cell/reagent consumption, reduced Joule heating and uniform and precise electric fields, microfluidic chips are perfect platforms for observing cell migration under applied electric fields. In this paper, I review recent developments in designing and fabricating microfluidic devices for studying electrotaxis, aiming to provide critical updates in this rapidly-growing, interdisciplinary field.

Real-time, label-free characterization of oligosaccharide-binding proteins using carbohydrate microarrays and an ellipsometry-based biosensor.

Carbohydrates present on cell surfaces mediate cell behavior through interactions with other biomolecules. Due to their structural complexity, diversity, and heterogeneity, it is difficult to fully characterize a variety of carbohydrates and their binding partners. As a result, novel technologies for glycomics applications have been developed, including carbohydrate microarrays and label-free detection methods. In this paper, we report using the combination of oligosaccharide microarrays and the label-free oblique-incidence reflectivity difference (OI-RD) microscopy for real-time characterization of oligosaccharide binding proteins. Aminated human milk oligosaccharides were immobilized on epoxy-coated glass substrates as microarrays for reactions with Family 1 of solute binding proteins from Bifidobacterium longum subsp. infantis (B. infantis). Binding affinities of these protein-oligosaccharide interactions showed preferences of Family 1 of solute binding proteins to host glycans, which helps in characterizing the complex process of human milk oligosaccharides foraging by B. infantis.

Evaluation of Kinetics Using Label-Free Optical Biosensors.

Optical biosensors provide a platform for qualitatively and quantitatively analyzing various biomolecular interactions. In addition to advantages such as label-free and high-throughput detection, these devices are also capable of measuring real-time binding curves in response to changes in optical properties of biomolecules. These kinetic data may be fitted to models to extract binding affinities such as association rates, dissociation rates, and equilibrium dissociation constants. In these biosensors, one of the binding pair is usually immobilized on a solid substrate for capturing the other. Due to the nature of these surface-based methods, mass transport effects and immobilization heterogenetity may cause problems when fitting the kinetic curves with the simple one-to-one Langmuir model. Here real-time binding curves of various antibody-antigen reactions were obtained by using an ellipsometry-based biosensor, and the results were fitted to the simple one-to-one model as well as a more sophisticated approach. The results show that the one-to-two model fitted much better to the curves than the one-to-one model. The two-site model may be explained by assuming two immobilization configurations on the surface. In summary, in fitting real-time curves obtained from optical biosensors, more sophisticated models are usually required to take surface-related issues, such as immobilization heterogenetity and mass transport effects within targets, into account.

Integration of Curved D-Type Optical Fiber Sensor with Microfluidic Chip.

A curved D-type optical fiber sensor (OFS) combined with a microfluidic chip is proposed. This OFS, based on surface plasmon resonance (SPR) of the Kretchmann's configuration, is applied as a biosensor to measure the concentrations of different bio-liquids such as ethanol, methanol, and glucose solutions. The SPR phenomenon is attained by using the optical fiber to guide the light source to reach the side-polished, gold-coated region. Integrating this OFS with a polymethylmethacrylate (PMMA)-based microfluidic chip, the SPR spectra for liquids with different refractive indices are recorded. Experimentally, the sensitivity of the current biosensor was calculated to be in the order of 10-5 RIU. This microfluidic chip-integrated OFS could be valuable for monitoring subtle changes in biological samples such as blood sugar, allergen, and biomolecular interactions.

Comparison of Chip Inlet Geometry in Microfluidic Devices for Cell Studies.

Micro-fabricated devices integrated with fluidic components provide an in vitro platform for cell studies best mimicking the in vivo micro-environment. These devices are capable of creating precise and controllable surroundings of pH value, temperature, salt concentration, and other physical or chemical stimuli. Various cell studies such as chemotaxis and electrotaxis can be performed by using such devices. Moreover, microfluidic chips are designed and fabricated for applications in cell separations such as circulating tumor cell (CTC) chips. Usually, there are two most commonly used inlets in connecting the microfluidic chip to sample/reagent loading tubes: the vertical (top-loading) inlet and the parallel (in-line) inlet. Designing this macro-to-micro interface is believed to play an important role in device performance. In this study, by using the commercial COMSOL Multiphysics software, we compared the cell capture behavior in microfluidic devices with different inlet types and sample flow velocities. Three different inlets were constructed: the vertical inlet, the parallel inlet, and the vertically parallel inlet. We investigated the velocity field, the flow streamline, the cell capture rate, and the laminar shear stress in these inlets. It was concluded that the inlet should be designed depending on the experimental purpose, i.e., one wants to maximize or minimize cell capture. Also, although increasing the flow velocity could reduce cell sedimentation, too high shear stresses are thought harmful to cells. Our findings indicate that the inlet design and flow velocity are crucial and should be well considered in fabricating microfluidic devices for cell studies.

Real-time, label-free detection of biomolecular interactions in sandwich assays by the oblique-incidence reflectivity difference technique.

One of the most important goals in proteomics is to detect the real-time kinetics of diverse biomolecular interactions. Fluorescence, which requires extrinsic tags, is a commonly and widely used method because of its high convenience and sensitivity. However, in order to maintain the conformational and functional integrality of biomolecules, label-free detection methods are highly under demand. We have developed the oblique-incidence reflectivity difference (OI-RD) technique for label-free, kinetic measurements of protein-biomolecule interactions. Incorporating the total internal refection geometry into the OI-RD technique, we are able to detect as low as 0.1% of a protein monolayer, and this sensitivity is comparable with other label-free techniques such as surface plasmon resonance (SPR). The unique advantage of OI-RD over SPR is no need for dielectric layers. Moreover, using a photodiode array as the detector enables multi-channel detection and also eliminates the over-time signal drift. In this paper, we demonstrate the applicability and feasibility of the OI-RD technique by measuring the kinetics of protein-protein and protein-small molecule interactions in sandwich assays.

A Droplet-Based Microfluidic Platform for High-Throughput Culturing of Yeast Cells in Various Conditions.

Yeast plays a significant role in a variety of fields. In particular, it is extensively used as a model organism in genetics and cellular biology studies, and is employed in the production of vaccines, pharmaceuticals, and biofuels. Traditional "bulk"-based studies on yeast growth often overlook cellular variability, emphasizing the need for single-cell analysis. Micro-droplets, tiny liquid droplets with high surface-area-to-volume ratios, offer a promising platform for investigating single or a small number of cells, allowing precise control and monitoring of individual cell behaviors. Microfluidic devices, which facilitate the generation of micro-droplets, are advantageous due to their reduced volume requirements and ability to mimic in vivo micro-environments. This study introduces a custom-designed microfluidic device to encapsulate yeasts in micro-droplets under various conditions in a parallel manner. The results reveal that optimal glucose concentrations promoted yeast growth while cycloheximide and Cu2+ ions inhibited it. This platform enhances yeast cultivation strategies and holds potential for high-throughput single-cell investigations in more complex organisms.

Highly reflective silver mirror enhanced by several dielectric films prepared under the low substrate temperature.

Optical paths in telescopes frequently incorporate silver mirrors for high sensitivity. Unfortunately, silver mirrors without protective coatings are susceptible to sulfurization and oxidation, compromising their quality. Even with protective layers, insufficient adhesion between the coating and the silver film can lead to peeling, exposing the silver to external environments and affecting its quality. This study aimed to identify dielectric materials with superior adhesion to silver, rendering them ideal choices for silver coating applications. By electron gun evaporation, different dielectric layers were deposited on the top and bottom of the silver film under a substrate temperature below 150 °C. These coatings were composed of materials with desired refractive indices, including aluminum oxide (Al2O3), aluminum-doped silicon, magnesium fluoride (MgF2), and other dielectrics. Following the deposition, a tape adhesion test was conducted to evaluate the bond strength of the samples. X-ray photoelectron spectroscopy (XPS) analysis was carried out to investigate the interaction between silver and its neighboring layers. The results revealed that Al2O3 and MgF2 exhibited exceptional adhesion to silver. Moreover, these multilayer coatings can effectively enhance the reflectance of silver in the visible (VIS) wavelength ranges.

Using microfluidic and conventional platforms to evaluate the effects of lanthanides on spheroid formation.

Metastasis contributes to the increased mortality rate of cancer, but the intricate mechanisms remain unclear. Cancer cells from a primary tumor invade nearby tissues and access the lymphatic or circulatory system. If these cells manage to survive and extravasate from the vasculature into distant tissues and ultimately adapt to survive, they will proliferate and facilitate malignant tumor formation. Traditional two-dimensional (2D) cell cultures offer a rapid and convenient method for validating the efficacy of anticancer drugs within a reasonable cost range, but their utility is limited because of tumors' high heterogeneity in vivo and spatial complexities. Three-dimensional (3D) cell cultures that mimic the physiological conditions of cancer cells in vivo have gained considerable interest. In these cultures, cells assemble into spheroids through gravity, magnetic forces, or their low-adhesion to the plates. Although these approaches address some of the limitations of 2D cultures, they often require a considerable amount of time and cost. Therefore, this study aims to enhance the effectiveness of 3D culture techniques by using microfluidic systems to provide a high-throughput and sensitive pipeline for drug screening. Using these systems, we studied the effects of lanthanide elements, which have garnered interest in cancer treatment, on spheroid formation and cell spreading. Our findings suggest that these elements alter the compactness of cell spheroids and decrease cell mobility.

Photoluminescence of Cesium-Doped Sodium Iodide Films Irradiated by UV LED.

Alkali metal halides have long been used as scintillators for applications as sensors and detectors. Usually, a small amount of impurities are added to these inorganic materials to improve their luminescence efficiencies. We investigate the structures and luminescent properties of un-doped sodium iodide (NaI) and cesium-doped NaI (NaI:Cs) films deposited by thermal vacuum evaporation. Instead of using the toxic element thallium (Tl), we introduced cesium dopant into NaI. This is the first study for the NaI:Cs film excited by UV LED's ultraviolet C (273 nm, 4.54 eV). The luminescence spectra show two main peaks at 3.05 and 4.32/3.955 eV (for fused silica/B270 substrate), originating from the intrinsic defects and/or activator excited states and the intrinsic self-trapped excitons (STEs), respectively. In general, both Cs-doping and post-annealing processes enhance the luminescence performance of NaI films.

Correction: Lin. et al. Effects of Substrate-Coating Materials on the Wound-Healing Process. Materials 2019, 12, 2775.

The authors wish to make the following correction to this paper [...].

Effects of Substrate-Coating Materials on the Wound-Healing Process.

The wound-healing assay is commonly and widely used for investigating collective cell migration under various physical and chemical stimuli. Substrate-coating materials are shown to affect the wound-healing process in a cell-type dependent manner. However, experiment-to-experiment variations make it difficult to compare results from different assays. In this paper, a modified barrier wound-healing assay was reported for studying the wound-healing process on different substrates in one single petri dish. In short, half of a dish was covered with the tape, and coating materials, poly-l-lysine and gelatin, were applied to the surface. After peeling off the tape, half of the surface was coated with the desired material. Then a customized barrier was placed inside the dish to create the wound. The results indicated that surface coating did not affect cell proliferation/viability, and the wound-healing rate increased in coated surfaces compared to uncoated ones. The present study provides a platform for further understanding the mechanisms of substrate coating-dependent wound-healing processes.

A microfluidics-based wound-healing assay for studying the effects of shear stresses, wound widths, and chemicals on the wound-healing process.

Collective cell migration plays important roles in various physiological processes. To investigate this collective cellular movement, various wound-healing assays have been developed. In these assays, a "wound" is created mechanically, chemically, optically, or electrically out of a cellular monolayer. Most of these assays are subject to drawbacks of run-to-run variations in wound size/shape and damages to cells/substrate. Moreover, in all these assays, cells are cultured in open, static (non-circulating) environments. In this study, we reported a microfluidics-based wound-healing assay by using the trypsin flow-focusing technique. Fibroblasts were first cultured inside this chip to a cellular monolayer. Then three parallel fluidic flows (containing normal medium and trypsin solution) were introduced into the channels, and cells exposed to protease trypsin were enzymatically detached from the surface. Wounds of three different widths were generated, and subsequent wound-healing processes were observed. This assay is capable of creating three or more wounds of different widths for investigating the effects of various physical and chemical stimuli on wound-healing speeds. The effects of shear stresses, wound widths, and ß-lapachone (a wound healing-promoting chemical) on wound-healing speeds were studied. It was found that the wound-healing speed (total area healed per unit time) increased with increasing shear stress and wound width, but under a shear stress of 0.174 mPa the linear healing speed (percent area healed per unit time) was independent of the wound width. Also, the addition of ß-lapachone up to 0.5 µM did not accelerate wound healing. This microfluidics-based assay can definitely help in understanding the mechanisms of the wound-healing process and developing new wound-healing therapies.

Fabrication of a Bare Optical Fiber-Based Biosensor.

A bare optical fiber-based biosensor is proposed for measuring the refractive index of different liquids and the binding kinetics of biomolecules to the sensor surface. This optical fiber sensor is based on the Kretschmann's configuration to attain total internal reflection (TIR) for surface plasmon resonance (SPR) excitation. One end of the bare optical fiber is coated with a gold film. By guiding the light source from the other end into the optical fiber, the light is reflected from the gold-deposited end and the surface evanescent wave is excited in the gold film-transparent material interface. Methanol and ethanol solutions with different refractive indices are used for measuring the corresponding changes in the peak values of the spectra and calculating the corresponding sensitivities. These values are experimentally determined to be in the order of 10-4~10-5 refractive index unit (RIU). Binding of proteins onto the sensor surface is also monitored in real time to obtain the binding kinetics. We believe that, in the future, this optical fiber sensor can serve as a useful biosensor for in situ measurement of allergens, antibody-antigen interactions, and even circulating tumor cells in the blood.

Establishing a quick screening method by using a microfluidic chip to evaluate cytotoxicity of metal contaminants.

Due to rapid industrialization and urbanization, the environment is exposed to many chemicals from natural or anthropogenic sources. The contaminants impact eco-system and human health via food chain. Animals, including humans, are likely to accumulate contaminants in their bodies from direct exposure or feeding behavior, resulting in toxicity. Therefore, evaluation of the toxicity of contaminants is an important issue. Metals are highly toxic but the toxicity depends on many factors, including the valance and the complex form of metals, the organic matter level in the environment, the reducing/oxidizing condition of the environment, and etc. Since the level of metal amount does not directly correlate to bioavailability, cell culture is usually used for toxicity evaluation. In this study, a microfluidic chip was developed to evaluate the cell toxicity from exposure to metals, copper and thallium. Compared to traditional cytotoxicity assay using static state culture with tetrazolium reagent, this microfluidic chip can generate various shear stresses by changing geometry of culture areas or flow rate. Enhancement of shear stresses could increase cell sensitivity toward metal exposure. Therefore, this platform provides a more sensitive platform for quantitative analysis of cell toxicity and could be applied to evaluate toxicity from environmental samples.

Direct-Current Electric Field Distribution in the Brain for Tumor Treating Field Applications: A Simulation Study.

Tumor Treating Fields (TTFields) in combination with chemotherapy and/or radiotherapy have been clinically reported to provide prolonged overall survival in glioblastoma patients. Alternating electric fields with frequencies of 100~300 kHz and magnitudes of 1~3 V/cm are shown to suppress the growth of cancer cells via interactions with polar molecules within dividing cells. Since it is difficult to directly measure the electric fields inside the brain, simulation models of the human head provide a useful tool for predicting the electric field distribution. In the present study, a three-dimensional finite element head model consisting of the scalp, the skull, the dura, the cerebrospinal fluid, and the brain was built to study the electric field distribution under various applied potentials and electrode configurations. For simplicity, a direct-current electric field was used in the simulation. The total power dissipation and temperature elevation due to Joule heating in different head tissues were also evaluated. Based on the results, some guidelines are obtained in designing the electrode configuration for personalized glioblastoma electrotherapy.

Design and Fabrication of a Microfluidic Viscometer Based on Electrofluidic Circuits.

This paper reports a microfluidic viscometer based on electrofluidic circuits for measuring viscosities of liquid samples. The developed micro-device consists of a polydimethylsiloxane (PDMS) layer for electrofluidic circuits, a thin PDMS membrane, another PDMS layer for sample pretreatment, and a glass substrate. As the sample flows inside the microfluidic channel, its viscosity causes flow resistance and a pressure drop along this channel. This pressure drop, in turn, generates a hydraulic pressure which deforms the PDMS membrane, causing changes in the cross-sectional area and the electrical resistance of the electrofluidic resistor. This small resistance change is then measured via the electrofluidic Wheatstone bridge to relate the measured voltage difference to the fluidic viscosity. The performance of this viscometer was first tested by flowing nitrogen gas with controllable pressures into the device. The relationship between measured voltage difference and input gas pressure was analyzed to be linear in the pressure range of 0⁻15 psi. Another test using pure water indicated good linearity between measured voltage difference and flow rate in the rate range of 20⁻100 µL/min. Viscosities of glycerol/water solutions with volume/volume (v/v) concentrations ranging from 0 to 30% were measured, and these values were close to those obtained using commercially available viscometers. In addition, the sample-pretreatment layer can be used to mix and/or dilute liquid samples to desired concentrations. Therefore, this microfluidic device has potential for measurements of fluidic viscosity in a fast, accurate, and high-throughput manner.

Electrical Stimulation for Wound-Healing: Simulation on the Effect of Electrode Configurations.

Endogenous electric field is known to play important roles in the wound-healing process, mainly through its effects on protein synthesis and cell migration. Many clinical studies have demonstrated that electrical stimulation (ES) with steady direct currents is beneficial to accelerating wound-healing, even though the underlying mechanisms remain unclear. In the present study, a three-dimensional finite element wound model was built to optimize the electrode configuration in ES. Four layers of the skin, stratum corneum, epidermis, dermis, and subcutis, with defined thickness and electrical properties were modeled. The main goal was to evaluate the distributions of exogenous electric fields delivered with direct current (DC) stimulation using different electrode configurations such as sizes and positions. Based on the results, some guidelines were obtained in designing the electrode configuration for applications of clinical ES.