A perovskite solar cell-photothermal-thermoelectric tandem system for enhanced solar energy utilization.

Photovoltaic-thermoelectric (PV-TE) tandem system has been considered as an effective way to fully utilize the solar spectrum, and has been demonstrated in a perovskite solar cell (PSC)-thermoelectric (TE) configuration. However, the conventional PSC-TE tandem architecture cannot convert infrared light transmitted through the upper PSC into heat effectively, impeding the heat-electricity conversion of TE devices. Herein, a semi-transparent PSC-photothermal-TE tandem system is designed for improved photothermal utilization. Through optimizing the buffer layer of the back transparent electrode, semi-transparent PSC with a power conversion efficiency (PCE) of 13% and an average transmittance of 53% in the range of 800-1500 nm was obtained. On this basis, a photothermal thin film was introduced between the semi-transparent PSC and the TE device, which increased the efficiency contribution ratio of the TE device from 14% to 19%, showing enhanced utilization of AM 1.5 G solar spectrum and improved photo-thermal-electric conversion efficiency.

We have constructed a semi-transparent perovskite solar cell-photothermal-thermoelectric tandem system through the optimization of transparent back electrode and the introduction of photothermal thin-film, realizing enhanced utilization of solar energy.

Abnormal Out-of-Plane Vibrational Raman Mode in Electrochemically Intercalated Multilayer MoS2.

Raman spectroscopy is a powerful technique to probe structural and doping behaviors of two-dimensional (2D) materials. In MoS2, the always coexisting in-plane (E2g1) and out-of-plane (A1g) vibrational modes are used as reliable fingerprints to distinguish the number of layers, strains, and doping levels. In this work, however, we report an abnormal Raman behavior, i.e., the absence of the A1g mode in cetyltrimethylammonium bromide (CTAB)-intercalated MoS2 superlattice. This unusual behavior is quite different from the softening of the A1g mode induced by surface engineering or electric-field gating. Interestingly, under a strong laser illumination, heating, or mechanical indentation, an A1g peak gradually appears, accompanied by the migration of intercalated CTA+ cations. The abnormal Raman behavior is mainly attributed to the constraint of the out-of-plane vibration due to intercalations and resulting severe electron doping. Our work renews the understanding of Raman spectra of 2D semiconducting materials and sheds light on developing next-generation devices with tunable structures.

Dielectric Matching by the Unique Dynamic Dipoles in Hybrid Organic/Inorganic Superlattices toward Ultrathin Microwave Absorber.

There is an urgent demand of ultrathin high-performance microwave absorbing materials (MAMs) in the electromagnetic protection field. However, minimizing thickness is challenging mainly due to dielectric mismatch at high permittivity from excessive dielectric loss, leading to strong reflection at 2-18 GHz. Here, a hybrid TaS2 /Co(Cp)2 superlattice is fabricated with alternating [TaS2 ] inorganic layers and [Co(Cp)2 ] organic layers. Dynamic Ta─Co dipoles offer a unique interfacial polarization relaxation mechanism involving the inversion and rotation of dynamic Ta─Co dipoles. The prolonged relaxation time of limited dynamic Ta─Co dipoles contributes to enhanced dielectric matching at high permittivity, which is essential for ultrathin high-performance MAMs. Furthermore, the confinement of paramagnetic Co(Cp)2 molecules in the interlayer space of the diamagnetic TaS2 sublattice triggers unexpected ferromagnetism via interfacial magnetic coupling conducive to the improved microwave-absorbing performance at reduced thickness. Therefore, it presents a 1.271-mm thick ultrathin absorber that can attenuate up to 99.99% of electromagnetic wave energy with a broad effective absorption bandwidth of 4.05 GHz, thus pushing the limits of thickness of 2D-based high-performance MAMs. This paper demonstrates a new strategy toward ultrathin MAMs with tunable and decent electromagnetic loss derived from electrical and magnetic coupling at the atomic scale.

Structure Features and Physicochemical Performances of Fe-Contained Clinoptilolites Obtained via the Aqueous Exchange of the Balanced Cations and Isomorphs Substitution of the Heulandite Skeletons for Electrocatalytic Activity of Oxygen Evolution Reaction and Adsorptive Performance of CO2.

Fe(III)-modified clinoptilolites (Fe-CPs) were prepared by hydrothermal treatment. The collapse of the heulandite skeletons was avoided by adjusting the pH value using HCl solution, showing the maximum relative crystallinity of the Fe-CPs at an optimal pH of 1.3. The competitive exchange performances between Fe3+ ions and H+ with Na+ (and K+) suggested that the exchange sites were more easily occupied by H+. Various characterizations verified that the hydrothermal treatments had a strong influence on the dispersion and morphology of the isolated and clustered Fe species. The high catalytic activity of the oxygen evolution reaction indicated the insertion of Fe3+ into the skeletons and the occurrences of isomorphic substitution. The fractal evolutions revealed that hydrothermal treatments with the increase of Fe content strongly affected the morphologies of Fe species with rough and disordered surfaces. Meanwhile, the Fe(III)-modified performances of the CPs were systematically investigated, showing that the maximum Fe-exchange capacity was up to 10.6 mg/g. Their thermodynamic parameters and kinetic performances suggested that the Fe(III)-modified procedures belonged to spontaneous, endothermic, and entropy-increasing behaviors. Finally, their adsorption capacities of CO2 at 273 and 298 K were preliminarily evaluated, showing high CO2 adsorption capacity (up to 1.67 mmol/g at 273 K).

Dysregulation of iron homeostasis and methamphetamine reward behaviors in Clk1-deficient mice.

Chronic administration of methamphetamine (METH) leads to physical and psychological dependence. It is generally accepted that METH exerts rewarding effects via competitive inhibition of the dopamine transporter (DAT), but the molecular mechanism of METH addiction remains largely unknown. Accumulating evidence shows that mitochondrial function is important in regulation of drug addiction. In this study,  we investigated the role of Clk1, an essential mitochondrial hydroxylase for ubiquinone (UQ), in METH reward effects. We showed that Clk1+/- mutation significantly suppressed METH-induced conditioned place preference (CPP), accompanied by increased expression of DAT in plasma membrane of striatum and hippocampus due to Clk1 deficiency-induced inhibition of DAT degradation without influencing de novo synthesis of DAT. Notably, significantly decreased iron content in striatum and hippocampus was evident in both Clk1+/- mutant mice and PC12 cells with Clk1 knockdown. The decreased iron content was attributed to increased expression of iron exporter ferroportin 1 (FPN1) that was associated with elevated expression of hypoxia-inducible factor-1α (HIF-1α) in response to Clk1 deficiency both in vivo and in vitro. Furthermore, we showed that iron played a critical role in mediating Clk1 deficiency-induced alteration in DAT expression, presumably via upstream HIF-1α. Taken together, these data demonstrated that HIF-1α-mediated changes in iron homostasis are involved in the Clk1 deficiency-altered METH reward behaviors.

Hybrid superlattices of two-dimensional materials and organics.

Two-dimensional (2D) materials have received extensive interest due to their exceptional properties. It is strongly required to assemble 2D materials in bulk quantities for macroscopic applications, but this is highly restricted by the aggregation of 2D materials. Constructing three-dimensional (3D) hybrid superlattices of alternating 2D materials and organic molecule layers provides a new path to access the exceptional properties of 2D materials in bulk quantities. In this tutorial review, the emerging concept of hybrid inorganic/organic superlattices is systematically illustrated. The abundant compositions and the various structures of inorganic and organic sublattices in hybrid superlattices are presented, followed by a summary of the chemical interactions between them. Many facile techniques have been developed for hybrid superlattices, enabling precise control of the structure. There are also various interesting mechanisms inside unique hybrid inorganic/organic superlattices that can help tune the properties, including electron transfer, quantum confinement, interlayer coupling, multiple interface effects, etc. The rich chemistry and abundant mechanisms of these hybrid superlattices can enhance the performance beyond the reach of existing materials, and provide new opportunities in various applications, including rechargeable batteries, catalysis, thermoelectrics, advanced electronics, superconductors, optoelectronics, etc.

Flexible Foil of Hybrid TaS2 /Organic Superlattice: Fabrication and Electrical Properties.

TaS2 nanolayers with reduced dimensionality show interesting physics, such as a gate-tunable phase transition and enhanced superconductivity, among others. Here, a solution-based strategy to fabricate a large-area foil of hybrid TaS2 /organic superlattice, where [TaS2 ] monolayers and organic molecules alternatively stack in atomic scale, is proposed. The [TaS2 ] layers are spatially isolated with remarkably weakened interlayer bonding, resulting in lattice vibration close to that of TaS2 monolayers. The foil also shows excellent mechanical flexibility together with a large electrical conductivity of 1.2 × 103 S cm-1 and an electromagnetic interference of 31 dB, among the highest values for solution-processed thin films of graphene and inorganic graphene analogs. The solution-based strategy reported herein can add a new dimension to manipulate the structure and properties of 2D materials and provide new opportunities for flexible nanoelectronic devices.

Folate deficiency facilitates recruitment of upstream binding factor to hot spots of DNA double-strand breaks of rRNA genes and promotes its transcription.

The biogenesis of ribosomes in vivo is an essential process for cellular functions. Transcription of ribosomal RNA (rRNA) genes is the rate-limiting step in ribosome biogenesis controlled by environmental conditions. Here, we investigated the role of folate antagonist on changes of DNA double-strand breaks (DSBs) landscape in mouse embryonic stem cells. A significant DSB enhancement was detected in the genome of these cells and a large majority of these DSBs were found in rRNA genes. Furthermore, spontaneous DSBs in cells under folate deficiency conditions were located exclusively within the rRNA gene units, representing a H3K4me1 hallmark. Enrichment H3K4me1 at the hot spots of DSB regions enhanced the recruitment of upstream binding factor (UBF) to rRNA genes, resulting in the increment of rRNA genes transcription. Supplement of folate resulted in a restored UBF binding across DNA breakage sites of rRNA genes, and normal rRNA gene transcription. In samples from neural tube defects (NTDs) with low folate level, up-regulation of rRNA gene transcription was observed, along with aberrant UBF level. Our results present a new view by which alterations in folate levels affects DNA breakage through epigenetic control leading to the regulation of rRNA gene transcription during the early stage of development.

Enhanced thermoelectric performance of Bi2Te3 through uniform dispersion of single wall carbon nanotubes.

The advancement in nanostructured powder processing has attracted great interest as a cost effective and scalable strategy for high performance thermoelectric bulk materials. However, the level of technical breakthrough realized in quantum dot supperlattices/wires has not yet been demonstrated in these materials. Here, we report the first ever study on the uniform dispersion of single wall carbon nanotubes (SWCNTs) in nanostructured Bi2Te3 bulk, and their effect on thermoelectric parameters above room temperature. The Bi2Te3 based SWCNT composites were prepared through controlled powder processing, and their thermoelectric properties were finely tuned at the nanoscale by regulating various (0.5, 0.75, 1.0 and 1.5) vol% of SWCNTs in the matrix. The flexible ropes of SWCNT, making an interconnected network through the inter/trans granular positions of Bi2Te3, thus substantially change the transport properties of the composites. The perfect one-dimensional (1D) conducting structure of SWCNTs acts as a source of electrical transport through a percolating network, with significantly suppressed lattice thermal conductivity, via intensified boundary scattering. The remarkable increase in power factor is ascribed to energy filtering effects and excellent electrical transport of 1D SWCNTs in the composites. Consequently, with a considerable reduction in thermal conductivity, the figure of merit culminates in a several-fold improvement, at 0.5 vol% of SWCNTs, over pristine bulk Bi2Te3.

Indium-doped SnO2 nanobelts for high-performance transparent and flexible photosensors by a facile assembly.

Flexible and transparent electronics is the emerging future technology for optoelectronic devices. Recently, it has attracted considerable attention from the research community due to its prodigious commercial applications. Herein, we report highly flexible and transparent ultraviolet photosensors based on indium-doped tin oxide nanobelts with enhanced simultaneous photosensitivity and recovery speed, compared to pure SnO2 nanobelts. Optoelectronic properties of the nanobelt photosensors have been found to be strongly related to the indium doping concentration and grain size of the nanobelts. A facile assembly method has been used to prepare the well-aligned nanobelt device for UV photosensors. Excellent flexible properties of the nanobelts have been explored, which show a superior response during bending tests and almost maintain their properties after 300 bending cycles. The enhanced photosensitivity of about 70 times that of undoped SnO2 nanobelts along with a highly enhanced recovery speed of less than 1.75 s have been achieved by the precise doping of In3+ into SnO2 lattice nanobelts. All these results show that our prepared photosensors demonstrate superior mechanical, electrical, and optical properties for their use in flexible and transparent electronics.

Flexible n-type thermoelectric materials by organic intercalation of layered transition metal dichalcogenide TiS2.

Organic semiconductors are attracting increasing interest as flexible thermoelectric materials owing to material abundance, easy processing and low thermal conductivity. Although progress in p-type polymers and composites has been reported, their n-type counterpart has fallen behind owing to difficulties in n-type doping of organic semiconductors. Here, we present an approach to synthesize n-type flexible thermoelectric materials through a facile electrochemical intercalation method, fabricating a hybrid superlattice of alternating inorganic TiS2 monolayers and organic cations. Electrons were externally injected into the inorganic layers and then stabilized by organic cations, providing n-type carriers for current and energy transport. An electrical conductivity of 790 S cm(-1) and a power factor of 0.45 mW m(-1) K(-2) were obtained for a hybrid superlattice of TiS2/[(hexylammonium)x(H2O)y(DMSO)z], with an in-plane lattice thermal conductivity of 0.12 ± 0.03 W m(-1) K(-1), which is two orders of magnitude smaller than the thermal conductivities of the single-layer and bulk TiS2. High power factor and low thermal conductivity contributed to a thermoelectric figure of merit, ZT, of 0.28 at 373 K, which might find application in wearable electronics.

Dielectric Mismatch Mediates Carrier Mobility in Organic-Intercalated Layered TiS2.

The dielectric constant is a key parameter that determines both optical and electronic properties of materials. It is desirable to tune electronic properties though dielectric engineering approach. Here, we present a systematic approach to tune carrier mobilities of hybrid inorganic/organic materials where layered two-dimensional transition-metal dichalcogenide TiS2 is electrochemically intercalated with polar organic molecules. By manipulating the dielectric mismatch using polar organic molecules with different dielectric constants, ranging from 10 to 41, the electron mobility of the TiS2 layers was changed three times due to the dielectric screening of the Coulomb-impurity scattering processes. Both the overall thermal conductivity and the lattice thermal conductivity were also found to decrease with an increasing dielectric mismatch. The enhanced electrical mobility along with the decreased thermal conductivity together gave rise to a significantly improved thermoelectric figure of merit of the hybrid inorganic/organic materials at room temperature, which might find applications in wearable electronics.

High Homocysteine-Thiolactone Leads to Reduced MENIN Protein Expression and an Impaired DNA Damage Response: Implications for Neural Tube Defects.

DNA damage is associated with hyperhomocysteinemia (HHcy) and neural tube defects (NTDs). Additionally, HHcy is a risk factor for NTDs. Therefore, this study examined whether DNA damage is involved in HHcy-induced NTDs and investigated the underlying pathological mechanisms involved. Embryonic day 9 (E9) mouse neuroectoderm cells (NE4C) and homocysteine-thiolactone (HTL, active metabolite of Hcy)-induced NTD chicken embryos were studied by Western blotting, immunofluorescence. RNA interference or gene overexpression techniques were employed to investigate the impact of Menin expression changes on the DNA damage. Chromatin immunoprecipitation-quantitative polymerase chain reaction was used to investigate the epigenetic regulation of histone modifications. An increase in γH2AX (a DNA damage indicator) was detected in HTL-induced NTD chicken embryos and HTL-treated NE4C, accompanied by dysregulation of phospho-Atr-Chk1-nucleotide excision repair (NER) pathway. Further investigation, based on previous research, revealed that disruption of NER was subject to the epigenetic regulation of low-expressed Menin-H3K4me3. Overexpression of Menin or supplementation with folic acid in HTL-treated NE4C reversed the adverse effects caused by high HTL. Additionally, by overexpressing the Mars gene, we tentatively propose a mechanism whereby HTL regulates Menin expression through H3K79hcy, which subsequently influences H3K4me3 modifications, reflecting an interaction between histone modifications. Finally, in 10 human fetal NTDs with HHcy, we detected a decrease in the expression of Menin-H3K4me3 and disorder in the NER pathway, which to some extent validated our proposed mechanism. The present study demonstrated that the decreased expression of Menin in high HTL downregulated H3K4me3 modifications, further weakening the Atr-Chk1-NER pathway, resulting in the occurrence of NTDs.

Organic-SnSe2 Hybrid Superlattice toward Synergistic Electrical Transport Optimization and Thermal Conductance Suppression.

Recently, layered SnSe2 has drawn broad research interest as a promising thermoelectric material that possesses great potential for application in energy conversion. However, extensive efforts have been devoted to optimizing the thermoelectric performance of SnSe2, but the ZT value is still far from satisfactory. Therefore, we developed an organic-inorganic superlattice hybrid by intercalating organic cations into SnSe2 interlayers in an attempt to enhance the thermoelectric properties. Organic intercalants can enlarge the basal spacing and decouple the SnSe2 layers, bringing about synergistic electrical transport modification and phonon softening. Thus, by simultaneously improving the electrical conductivity and reducing the thermal conductivity, a ZT value of 0.34 is achieved at 342 K in tetrabutylammonium-intercalated SnSe2, approximately two orders of magnitude higher than that of pristine SnSe2 single crystals. In addition, by opening van der Waals gaps via organic cations, outstanding flexibility of organic-intercalated SnSe2 is realized, with a superior figure of merit for flexibility of approximately 0.068. This work demonstrates a general and facile strategy to fabricate organic-inorganic superlattice hybrids with a considerable improvement in the thermoelectric performance via organic cation intercalation, which is promising for flexible thermoelectrics.

Constructing Randomly Lamellar HKUST-1@Clinoptilolite through Polyethylene Glycol-Assisted Hydrothermal Method and Coordinated Complexation for Enhanced Adsorptive Separation for CO2 and CH4.

Clinoptilolite (CP) was successfully synthesized via a hydrothermal route in the presence of polyethylene glycol (PEG), and it was then delaminated by washing using Zn2+ containing acid. HKUST-1, as one kind of the Cu-based MOFs, showed a high CO2 adsorption capacity owing to its large pore volume and specific surface area. In the present work, we selected one of the most efficient ways for preparing the HKUST-1@CP compounds via coordination between exchanged Cu2+ and ligand (trimesic acid). Their structural and textural properties were characterized by XRD, SAXS, N2 sorption isotherms, SEM, and TG-DSC profiles. Particularly, the effect of the additive PEG (average molecular weight of 600) on the induction (nucleation) periods and growth behaviors were detailed and investigated in the hydrothermal crystallization procedures of synthetic CPs. The corresponding activation energies of induction (En) and growth (Eg) periods during crystallization intervals were calculated. Meanwhile, the pore size of the inter-particles of HKUST-1@CP was 14.16 nm, and the BET specific area and pore volume were 55.2 m2/g and 0.20 cm3/g, respectively. Their CO2 and CH4 adsorption capacities and selectivity were preliminarily explored, showing 0.93 mmol/g for HKUST-1@CP at 298 K with the highest selective factor of 5.87 for CO2/CH4, and the dynamic separation performance was evaluated in column breakthrough experiments. These results suggested an efficient way of preparing zeolites and MOFs composites that is conducive to being a promising adsorbent for applications in gas separation.

Novel IKBKG gene mutations in incontinentia pigmenti: report of two cases.

Incontinentia pigmenti (IP), an X-chromosome dominant genodermatosis caused by mutations in the IKBKG/NEMO gene, is a rare disease affecting the skin, teeth, eyes, and central nervous system. Here, we report two pedigrees of IP and detection of two novel mutations in the IKBKG gene associated with IP via genetic analysis. In addition, different gene mutation types can present with different clinical phenotypes, and the same gene mutation type can show different clinical phenotypes. This study provides clinical cases for further study of the genotype and phenotype of IP and enriches the mutation spectrum of IKBKG gene, which provides a basis for genetic counseling and genetic diagnosis of IP in the future.

Carrier-filtering and phonon-blocking AgSnSe2-decorated grain boundaries to boost the thermoelectric performance of Cu2Sn0.9Co0.1S3.

Heavily co-doped Cu2SnS3 can achieve a high power factor by relying on a high electrical conductivity (σ), which subsequently limits the ZT value with a large electronic thermal conductivity (κe). We report here an enhanced ZT for Cu2Sn0.9Co0.1S3 decorated with micro-nanoscale AgSnSe2 along grain boundaries. The AgSnSe2 phase served as a charge carrier filter by ionized impurity scattering, with a noticeable bottoming out of carrier mobility and a rapid increase in the Seebeck coefficient as the temperature increased from 423 to 573 K, which properly reduced the large σ and κe while maintaining a high power factor of approximately 10 µW cm-1 K-2 at 773 K. Lattice thermal conductivity was markedly suppressed, and a low total thermal conductivity was obtained with strengthened phonon scattering by the AgSnSe2 phase as a phonon barrier. With the synergistic effects on electrical and thermal transport, a maximum ZT of 0.93 at 773 K was achieved in Cu2Sn0.9Co0.1S3-3 wt% AgSnSe2.

Near-Infrared Trapping by Surface Plasmons in Randomized Platinum-Ceramic Metamaterial for Thermal Barrier Coatings.

As the operation temperature of next generation gas turbine is targeted to be 1800 °C toward a higher efficiency and lower carbon emission, the near-infrared (NIR) thermal radiation becomes a major concern for the durability of the metallic turbine blades. Although thermal barrier coatings (TBCs) are applied to provide thermal insulations, they are translucent to the NIR radiation. It is a major challenge for TBCs to achieve optically thick with limited physical thickness (usually < 1 mm) for effectively shielding the NIR radiation damage. Here, an NIR metamaterial is reported, where a Gd2 Zr2 O7 ceramic matrix is randomly dispersed with microscale Pt (0.53 vol%) nanoparticles with a size of 100-500 nm. Attenuated by the Gd2 Zr2 O7 matrix, a broadband NIR extinction is achieved through the red-shifted plasmon resonance frequencies and higher-order multipole resonances of the Pt nanoparticles. A very high absorption coefficient of ≈3 × 104 m-1 , approaching the Rosseland diffusion limit for a typical coating thickness, minimizes the radiative thermal conductivity to ≈10-2  W m-1 K-1 and successfully shields the radiative heat transfer. This work suggests that constructing a conductor/ceramic metamaterial with tunable plasmonics could be a strategy to shield NIR thermal radiation for high temperature applications.

Robustly Enhanced Seebeck Coefficient in the MXene/Organics/TiS2 Misfit Structure for Flexible Thermoelectrics.

The flexible thermoelectric (TE) generator has emerged as a superior alternative to traditional batteries for powering wearable electronic devices, as it can efficiently convert skin heat into electricity without any safety concerns. MXene, a highly researched two-dimensional material, is known for its exceptional flexibility, hydrophilicity, metallic conductivity, and processability, among other properties, making it a versatile material for a wide range of applications, including supercapacitors, electromagnetic shielding, and sensors. However, the low intrinsic Seebeck coefficient of MXene due to its metallic conducting nature poses a significant challenge to its TE application. Therefore, improving the Seebeck coefficient remains a primary concern. In this regard, a flexible MXene/organics/TiS2 misfit film was synthesized in this work through organic intercalation, exfoliation, and re-assembly techniques. The absolute value of Seebeck coefficient of the misfit film was significantly enhanced to 44.8 µV K-1, which is five times higher than that of the original MXene film. This enhancement is attributed primarily to the weighted effect of the Seebeck coefficient and possibly to energy-filtering effects at the heterogeneous interfaces. Additionally, the power factor of the misfit film was considerably improved to 77.2 µW m-1 K-2, which is 18 times higher than that of the original MXene film. The maximum output power of the TE device constructed of the misfit film was 95 nW at a temperature difference of 40 K, resulting in a power density of 1.18 W m-2, demonstrating the significant potential of this technology for driving low-energy consumption wearable electronics.

Recalcitrant nodular scabies showing excellent response to tofacitinib: five case reports.

Scabies is a contagious skin condition caused by Sarcoptes scabiei, and it is always associated with an intense, unbearable, nocturnal deteriorating itch. Its presentations include classic burrows, erythema, pruritic papules, pustules, vesicles, and inflammatory nodules, with diffuse or localized distribution on the finger webs, wrist flexors, elbows, axillae, buttocks, genitalia, and breasts. Nodular scabies is an uncommon clinical variant of scabies. Its management is still challenging for some patients up to date, although topical, intralesional or systemic corticosteroids, topical calcineurin inhibitors, and crotamiton as well as cryotherapy alone or in different combinations are used. We here report five male patients of nodular scabies, aged between 14 and 25 years, who had classical scabies that had been cured by sulfur ointment for at least 4 weeks except for their itching nodules, and their residual pruritic nodules also failed in previous treatments including antihistamines, topical applying and intralesional injection of steroids as well as topical tacrolimus in different combinations before being recruited to this study. The patients were administered tofacitinib 5 mg, twice a day, which led to excellent and rapid improvement for both lesions and symptoms after 1-4 weeks of treatment, respectively, without any associations. During 6 months of follow-up, only one had re-infection of scabies associated with nodules that were cured by sulfur ointment and tofacitinib again. No adverse reaction was observed. The present results suggested that tofacitinib might be a potential agent for nodular scabies with excellent response.