Analysis of Pre-Driver and Last-Stage Power-Ground-Induced Jitter at Different PVT Corners.

This paper presents the study of power/ground (P/G) supply-induced jitter (PGSIJ) on a cascaded inverter output buffer. The PGSIJ analysis covers the IO buffer transient simulation under P/G supply voltage variation at three process, voltage, and temperature (PVT) corners defined at different working temperatures and distinct P/G DC supply voltages at the pre-driver (i.e., VDD/VSS) and last stage (i.e., VDDQ/VSSQ). Firstly, the induced jitter contributions by the pre-driver, as well as the last, stage are compared and studied. Secondly, the shared and decoupled P/G supply topologies are investigated. The outcomes of these simulation analyses with respect to worst case jitter corners are determined, while highlighting the importance of modeling the pre-driver circuit behavior to include the induced jitter in the input-output buffer information specification (IBIS)-like model. Accordingly, the measured PGSIJ depends on the corners to be analyzed and, therefore, the designer needs to explore the worst-case corner for the driver's technology node and the most supply voltage noise affecting the jitter output for signal and power integrity (SiPI) simulations. Finally, the jitter transfer function sensitivity to the amplitude and frequency/phase variations of the separate and combined impacts of the pre-driver and last stage are explored, while discussing the superposition of the power supply induced jitter (PSIJ) induced by both the driver's IO stages under small signal and large signal supply voltage variations. The linear superposition of the separate PSIJ effects by the pre-driver and last stage depends on the amplitude of the variation of the supply voltage that can drive the transistor to their nonlinear working regions.

Head Trajectory Diagrams for Gait Symmetry Analysis Using a Single Head-Worn IMU.

Gait symmetry analysis plays an important role in the diagnosis and rehabilitation of pathological gait. Recently, wearable devices have also been developed for simple gait analysis solutions. However, measurement in clinical settings can differ from gait in daily life, and simple wearable devices are restricted to a few parameters, providing one-sided trajectories of one arm or leg. Therefore, head-worn devices with sensors (e.g., earbuds) should be considered to analyze gait symmetry because the head sways towards the left and right side depending on steps. This paper proposed new visualization methods using head-worn sensors, able to facilitate gait symmetry analysis outside as well as inside. Data were collected with an inertial measurement unit (IMU) based motion capture system when twelve participants walked on the 400-m running track. From head trajectories on the transverse and frontal plane, three types of diagrams were displayed, and five concepts of parameters were measured for gait symmetry analysis. The mean absolute percentage error (MAPE) of step counting was lower than 0.65%, representing the reliability of measured parameters. The methods enable also left-right step recognition (MAPE ≤ 2.13%). This study can support maintenance and relearning of a balanced healthy gait in various areas with simple and easy-to-use devices.

Impact of Wind Gust on High-Speed Characteristics of Polarization Mode Dispersion in Optical Power Ground Wire Cables.

Polarization mode dispersion is recognized as a key factor limiting optical transmission systems, particularly those fiber links that run at bit rates beyond 10 Gbps. In-line test and characterization of polarization mode dispersion are thus of critical importance to evaluate the quality of installed optical fibers that are in use for high-speed signal traffics. However, polarization-based effects in optical fibers are stochastic and quite sensitive to a range of environmental changes, including optical cable movements. This, in turn, gives rise to undesired variations in light polarization that adversely impair the quality of the signal transmission in the link. In this work, we elaborate on experimental testing and theoretical analysis to asses changes of polarization mode dispersion in optical fibers that are caused by environmental variations, here wind gusts in particular. The study was performed on commercially harnessed optical fibers installed within optical power ground wire cables, taking into account different weather conditions. More specifically, we showed that changes caused by wind gusts significantly influence the differential group delay and the principal state of polarization in those optical fibers. For this, we experimentally measured a number of parameters to characterize light polarization properties. Measurements were carried out on C-band operated fiber-optic link formed by 111-km-long power ground wire cables and 88 spectral channels, with a test time step of 1 min during 12 consecutive days. Variations in differential group delay allowed for sensitive testing of environmental changes with measured maxims up to 10 ps under the worst wind conditions. Moreover, measured parameters were used in a numerical model to assess the quality of transmitted high-bit-rate optical signals as a function of wind conditions. The analysis revealed a negligible impact of wind on a 10 Gbps transmission, while substantial influence was noticed for higher bit rates up to 100 Gbps. These results show promises for efficient sensing of environmental changes and subsequent monitoring of the quality of recently used fiber-optic link infrastructures.

Fabrication and Characterization of Planar-Type Top-Illuminated InP-Based Avalanche Photodetector on Conductive Substrate with Operating Speeds Exceeding 10 Gbps.

This paper presents a high-speed top-illuminated InP-based avalanche photodetector (APD) fabricated on conductive InP-wafer using planar processes. The proposed device was then evaluated in terms of DC and dynamic performance characteristics. The design is based on a separate absorption, grading, charge, and multiplication (SAGCM) epitaxial-structure. An electric field-profile of the SAGCM layers was derived from the epitaxial structure. The punch-through voltage of the SAGCM APD was controlled to within 16⁻17 V, whereas the breakdown voltage (VBR) was controlled to within 28⁻29 V. We obtained dark current of 2.99 nA, capacitance of 0.226 pF, and multiplication gain of 12, when the APD was biased at 0.9 VBR at room temperature. The frequency-response was characterized by comparing the calculated 3-dB cut-off modulation-frequency (f3-dB) and f3-dB values measured under various multiplication gains and modulated incident powers. The time-response of the APD was evaluated by deriving eye-diagrams at 0.9 VBR using pseudorandom non-return to zero codes with a length of 231-1 at 10⁻12.5 Gbps. There was a notable absence of intersymbol-interference, and the signals remained error-free at data-rates of up to 12.5 Gbps. The correlation between the rise-time and modulated-bandwidth demonstrate the suitability of the proposed SAGCM-APD chip for applications involving an optical-receiver at data-rates of >10 Gbps.

A novel dual polarization multiplexing RoF system integrating optical fiber and FSO channel with AMI downlink signals.

Using dual polarization multiplexing alternate mark inversion (AMI) downlink signals, a novel radio over fiber (RoF) system integrating optical fiber and FSO channel is designed to adapt to applications in mountainous areas and other complex terrain areas. Optical heterodyne technology and self-mixing homodyne detection method are used to realize high sensitivity detection of the received signals after 25.1 km channel (including 1 km single-mode fiber and 100 m free space link) transmission. Moreover, polarization multiplexing technology is introduced to exponentially increase the transmission capacity of downlink signals. This scheme not only can be compatible with traditional optical fiber transmission systems, but also support the wireless optical access application of millimeter wave signals in RoF systems.

Ultra-Bend-Resistant 4-Core Simplex Cable Used for Short-Reach Dense Spatial Division Multiplexing Optical Transmission.

We optimized and fabricated an ultra-bend-resistant 4-core simplex cable (SXC) employing 4-core multicore fiber (MCF) suitable for short-reach dense spatial division multiplexing (DSDM) optical transmission in the O-band. The characteristics of transmission loss, macro-bending and cross-talk (XT) between adjacent cores after cabling were firstly clarified. By introducing the trapezoid index and optimizing the cabling process, the maximum values of added XT of 1.17 dB/km due to 10 loops with a bending radius of 6 mm imposed over the 4-core SXC and a macro-bending loss of 0.37 dB/10 turns were, respectively, achieved.P Then, the optical transmission with low bit error rate (BER) was presented using a 100GBASE-LR4 transceiver over the 1.2 km long 4-core SXC. The excellent bending resistance of the 4-core SXC may pave the way for a reduction in space pressure and increase in access density on short-reach optical interconnect (OI) based on DSDM.

Research on high-speed digital optical signal jitter measurement technology based on clock recovery algorithm using eye diagram opening area.

With the rapid development of information technology, high-speed digital optical signal transmission technology has become the core of modern communication networks. However, the increase in transmission rates brings challenges such as noise, distortion, and interference, which affect the accuracy of clock recovery. To address these issues, this study proposes a clock recovery algorithm based on the eye diagram opening area to improve the accuracy and efficiency of high-speed digital optical signal jitter measurement. The proposed method extracts clock information from the signal using the opening area and curvature characteristics of the eye diagram for jitter measurement. Experimental results demonstrate that the clock recovery algorithm based on the eye diagram opening area can stably reconstruct the signal eye diagram and obtain jitter parameters under different optical power conditions. At optical powers of -7.2 dBm, -12.2 dBm, and -17.2 dBm, the Q-factors were 8.8, 7.6, and 4.3, respectively, and the RMS jitter values were 12.2 ps, 13.4 ps, and 21.2 ps, respectively. At optical powers of -2.3 dBm, 0.1 dBm, 2.4 dBm, 4.6 dBm, and 6.0 dBm, the Q-factors were 9.1, 9.3, 9.5, 9.7, and 10.0, respectively, and the average jitter values were 8.9 ps, 8.5 ps, 8.0 ps, 7.5 ps, and 7.0 ps. These results indicate that the proposed algorithm performs excellently under low optical power conditions and maintains high recovery accuracy even when jitter increases at higher optical powers. The clock recovery algorithm based on the eye diagram opening area significantly improves the accuracy and stability of high-speed digital optical signal jitter measurement, enriches the theoretical research of clock recovery algorithms, and shows significant advantages in improving signal transmission quality, reducing bit error rate, and enhancing communication link reliability. The research outcomes provide key technical support for the optimization of modern high-speed optical communication systems.

Performance Analyses of Photonic-Crystal Surface-Emitting Laser: Toward High-Speed Optical Communication.

This study conducts comprehensive performance analyses of a commercial photonic-crystal surface-emitting laser (PCSEL) via small-signal measurement and the bit-error-rate test. Meanwhile, the radio frequency characteristics of the PCSEL are unveiled for the first time. Compared to the vertical-cavity surface-emitting lasers, the PCSEL shows great potential for a broader optical bandwidth that is benefited from the high optical-confinement factor. A maximum bandwidth of around 2.32 GHz is experimentally observed when the PCSEL was biased at 340 mA. Moreover, a theoretical calculation was applied to shed light on the characteristics of the small-signal measurement, providing a deep insight into the corresponding intrinsic response model. The signal transmission capability of the PCSEL was investigated as well. The maximum bit rate and corresponding rise time transmitted at 500 Mbps are 1.2 Gbps and 186.16 ps, respectively. Thus, a high-speed PCSEL can be realised with a shrunk form factor, serving as a promising candidate for the next-generation light sources in high-speed optical communication.