Purification of Polyphenols from Distiller's Grains by Macroporous Resin and Analysis of the Polyphenolic Components.

We aimed to purify polyphenols from distiller's grain extract using macroporous resins and to identify its polyphenolic components. The influence of operational parameters on purification efficiency was investigated. The polyphenolic composition was analyzed by ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) and then quantified by UPLC-MS using authenticated standards. The results showed that the optimal purifying conditions were D101 resin with a dosage of 3 g, four hours adsorption, three hours desorption time, and 60% ethanol as the eluent, producing the highest purification rate of 51%. The purified distiller's grain extract exhibited stronger antioxidant activity than the unpurified extracts, which was assessed using DPPH and ABTS methods (IC50 DPPH = 34.03 and 16.21 µg/mL, respectively; IC50 ABTS = 20.31 and 5.73 µg/mL, respectively). UPLC-MS results indicated that (-)-epicatechin is the major compound found in distiller's grain extract which was quantified as 562.7 µg/g extract, followed by ferulic acid (518.2 µg/g), p-hydroxybenzoic acid (417.7 µg/g), caffeic acid (217.1 µg/g), syringic acid (158.0 µg/g) and quercetin (147.8 µg/g). Two compounds, vanillic acid (66.5 µg/g) and gallic acid (41.4 µg/g), were found in lower concentrations. The findings of this study suggest that purification of polyphenolic compounds from distiller's grain by macroporous resins is feasible, providing a new and effective method for the secondary use of distiller's grain resources.

Enantioseparation and determination of dufulin enantiomers in cucumber and soil by chiral liquid chromatography-tandem mass spectrometry.

A simple and rapid method for enantioselective determination of dufulin in cucumber and soil was developed by liquid chromatography with tandem mass spectrometry. The enantiomers were separated on a Superchiral S-OD chiral cellulose tris(3,5-dimethylphenylcarbamate) column at 20°C, with a mixture of acetonitrile and water (0.1% formic acid; 52:48, v/v) as mobile phase at a flow rate of 0.65 mL/min. The pretreatment conditions were optimized using an orthogonal test, and the optimized method showed good linearity and sensitivity. The limits of detection and limits of quantification of two dufulin enantiomers were 0.006 and 0.02 mg/kg, respectively. The average recoveries of S-enantiomer and R-enantiomer in cucumber and soil were 80.61-99.83% and 80.97-102.96%, respectively, with relative standard deviations of 1.30-9.72%. The method was successfully applied to determine dufulin in real cucumber and soil samples. The results demonstrate that the method could facilitate further research on the differences between individual dufulin enantiomers with respect to metabolites and environmental fate and finally help reveal the complex interactions that exist between dufulin, humans and the environment.

Chiral separation of benzothiazole derivatives of amino acids using capillary zone electrophoresis.

A method for the separation of enantiomers of leucine and phenylalanine benzothiazole derivatives as potential antimicrobial agents was developed using capillary zone electrophoresis with a dual cyclodextrin (CD) system. The best resolution of enantiomers was achieved in 100 mmol/L phosphate background electrolyte (pH 3.5) with the dual CD system consisting of 10 mmol/L of ß-CD with 10 mmol/L of 2-hydroxypropyl-ß-cyclodextrin for leucine derivative and 10 mmol/L of 2-hydroxypropyl-γ-cyclodextrin for phenylalanine derivative, respectively. Under the optimal conditions, the highest enantioresolution of 1.25 was achieved in a noncoated-fused silica capillary at 17°C and 24 kV applied voltage.

Preparation of phosphorylcholine-based hydrophilic monolithic column and application for analysis of drug-related impurities with capillary electrochromatography.

A hydrophilic monolithic CEC column was prepared by thermal copolymerization of zwitterionic monomer 2-methacryloyloxyethyl phosphorylcholine (MPC), pentaerythritol triacrylate (PETA), either methacrylatoethyl trimethyl ammonium chloride (META) or sodium 2-methylpropene-1-sulfonate (MPS) in a polar binary porogen consisting of methanol and THF. A typical hydrophilic interaction LC retention mechanism was observed for low-molecular weight polar compounds including amides, nucleotides, and nucleosides in the separation mode of hydrophilic interaction CEC, when high content of ACN (>60%) was used as the mobile phase. The effect of the electrostatic interaction between the analytes and the stationary phase was found to be negligible. The poly(MPC-co-PETA-co-META or MPS) monolithic columns have an average column efficiency of 40 000 plates/m and displayed with a satisfactory repeatability in terms of migration time and peak areas. Finally, the column was successfully applied to determine the impurities of a positively charged drug pramipexole which are often separated by ion pair RP chromatography due to their high hydrophilicity. All four components can be baseline separated within 5 min with BGE consisting of ACN/20 mM ammonium formate buffer (pH 3.0; 80/20).

Development of a Validated LC Method for Separation of Process-Related Impurities Including the R-Enantiomer of S-Pramipexole on Polysaccharide Chiral Stationary Phases.

Despite the availability of a few methods for individual separation of S-pramipexole from its process-related impurities, no common liquid chromatography (LC) method is reported so far in the literature. The present article describes the development of a single-run LC method for simultaneous determination of S-pramipexole and its enantiomeric and process-related impurities on a Chiralpak AD-H (150 x 4.6 mm, 5µm) column using n-hexane/ethanol/n-butylamine (75:25:0.1 v/v/v) as a mobile phase in an isocratic mode of elution at a flow rate of 1.2 ml/min at 30°C. The chromatographic eluents were monitored at a wavelength of 260 nm using a photodiode array detector. Excellent enantioseparation with good resolutions (Rs ≥ 2.88) and peak shapes (As ≤ 1.21) for all analytes was achieved. The proposed method was validated according to International Conference Harmonization (ICH) guidelines in terms of accuracy, precision, sensitivity, and linearity. Limits of quantification of impurities (0.25-0.55 µg/ml) indicate the highest sensitivity achievable by the proposed method. The method has an advantage of selectivity and suitability for routine determination of not only chiral impurity but also all possible related substances in active pharmaceutical ingredients of S-pramipexole.

Solvent bar microextraction combined with high-performance liquid chromatography for preconcentration and determination of pramipexole in biological samples.

A simple, rapid and sensitive analytical method for preconcentration and determination of pramipexole in different biological samples has been developed using solvent bar microextraction (SBME) combined with HPLC-UV. The target drugs were extracted from 10 mL of basic aqueous sample solution into an organic extracting solvent located inside the pores of a polypropylene hollow fiber, then back-extracted into an acidified aqueous solution in the lumen of the hollow fiber. In order to obtain high extraction efficiency, the effect of different variables on the extraction efficiency was studied simultaneously using an experimental design. The experimental parameters of SBME were optimized using a Box-Behnken design after a Plackett-Burman screening design. Under the optimized conditions, an enrichment factor up to 96 was achieved and the relative standard deviation of the method was 4.64% (n = 5). The linear range was 0.05-2000 µg/L with a correlation coefficient (r) of 0.987. Finally, the applicability of the proposed method was evaluated by extraction and determination of pramipexole in plasma and urine samples. The results indicated that SBME method has excellent clean-up and high preconcentration factor and can serve as a simple and sensitive method for analysis of pramipexole in biological samples.

Determination of benzotriazoles and benzothiazoles in human urine by liquid chromatography-tandem mass spectrometry.

Benzotriazole (BTR) and benzothiazole (BTH) derivatives are used in a wide variety of industrial and consumer products and have been reported to occur in the environment. Owing to a lack of analytical methods, human exposure to BTR and BTH is still unknown. In this study, a liquid chromatography-electrospray ionization tandem mass spectrometry (LC-ESI(+)MS/MS) method was developed for simultaneous determination of five 1,2,3-benzotriazoles and five 1,3-benzothiazoles in human urine. The target benzotriazoles were 1H-benzotriazole, 1-hydroxy-benzotriazole, tolyltriazole, xylyltriazole (or 5,6-dimethyl-1H-benzotriazole), and 5-chloro-benzotriazole, and the target benzothiazoles were benzothiazole, 2-hydroxy-benzothiazole, 2-methylthio-benzothiazole, 2-amino-benzothiazole, and 2-thiocyanomethylthio-benzothiazole. Urine specimens were enzymatically deconjugated with ß-glucuronidase and extracted by a solid-phase extraction (SPE) procedure for the measurement of total concentrations (i.e., free + conjugated forms) of BTRs and BTHs. Additionally, a liquid-liquid extraction (LLE) method was developed for comparison of extraction efficiencies between SPE and LLE. The limits of detection (LODs) ranged from 0.07 (2-amino-benzothiazole) to 4.0 ng/mL (benzothiazole) for the SPE method and from 0.04 (tolyltriazole) to 6.4 ng/mL (benzothiazole) for the LLE method. A total of 100 urine specimens, collected from Athens, Greece, were analyzed by enzymatic deconjugation and SPE. Benzothiazole and tolyltriazole were found frequently, and their concentrations were on the order of a few ng/mL. To our knowledge, this is the first study on the occurrence of 10 BTR and BTH compounds in human urine.

Optimization of a dispersive liquid-liquid microextraction method for the analysis of benzotriazoles and benzothiazoles in water samples.

A simple and rapid dispersive liquid-liquid microextraction method has been developed for the determination of 11 benzotriazoles and benzothiazoles in water samples. Tri-n-butylphosphate (TBP) was used as extractant, thus avoiding the use of toxic water-immiscible chlorinated solvents. The influence of several variables (e.g., type and volume of dispersant and extraction solvents, sample pH, ionic strength, etc.) on the performance of the sample preparation step was systematically evaluated. Analytical determinations were carried out by high-performance liquid chromatography with fluorescence and UV detection and liquid chromatography-electrospray ionization-tandem mass spectrometry. The optimized method exhibited a good precision level with relative standard deviation values between 3.7% and 8.4%. Extraction yields ranging from 67% to 97% were obtained for all of these considered compounds. Finally, the proposed method was successfully applied to the analysis of benzotriazoles and benzothiazoles in real water samples (tap, river, industrial waters, and treated and raw wastewaters).

Development and validation of a chiral capillary electrophoresis method for assay and enantiomeric purity control of pramipexole.

A rapid method for the enantioseparation of pramipexole and its R-enantiomer has been developed by capillary electrophoresis. The influence of chemical and instrumental parameters was investigated including the type and concentration of chiral selectors, buffer composition and pH, co-ions, applied voltage, capillary length and temperature. Optimal separation conditions were obtained using a 50 mM phosphate buffer (pH 2.8) containing 25 mM carboxymethyl-ß-cyclodextrin on a fused-silica capillary. Online UV detection was performed at 262 nm. A voltage of 25 kV was applied, and the capillary temperature was kept at 25°C. Hydrodynamic injection was performed at 3.45 kPa for 5.0 s. The separation of enantiomers was achieved in <6.5 min. The method was further validated in terms of stability of solutions, selectivity, linearity (both pramipexole and R-enantiomer, R(2) >0.995), LOD and LOQ (0.91 and 2.94 µg/mL, respectively), repeatability (RSD<1.5%) and accuracy (pramipexole, 100.4%; R-enantiomer, 100.5%). The proposed method was then applied to two kinds of pramipexole dihydrochloride monohydrate commercially available tablets, immediate release tablets (1.50 and 0.125 mg) and sustained release tablets (0.52 mg), to quantify the main component in the tablets. The amount of distomer could be quantified in bulk sample materials.

Determination of benzotriazole and benzothiazole derivatives in marketed fish by double-vortex-ultrasonic assisted matrix solid-phase dispersion and ultrahigh-performance liquid chromatography-high resolution mass spectrometry.

Benzotriazoles (BTRs) and benzothiazoles (BTs) are two groups of emerging concern and high production volume contaminants. Via the biomagnification of the food web, they could jeopardize human health. In this work, rapid determining the presence of five BTRs and two BTs in marketed fish was performed by a novel double-vortex-ultrasonic assisted matrix solid-phase dispersion (DVUA-MSPD) and UHPLC-electrospray ionization (+)-quadrupole time-of-flight mass spectrometry detection. Unlike traditional MSPD, we simplified the method without the use of mortar/pestle and SPE-column procedures. The DVUA-MSPD factors were screened by a multilevel categorical design, and then optimized by Box-Behnken Design plus with response surface methodology. The limits of quantification were 0.15-2 ng g-1 (dry weight). The satisfactory average recovery ranged from 70% to 93% with RSDs less than 9%. The developed method was successfully applied for the rapid determination of selected BTRs and BTs in fish samples at trace-level.

Identification of a small molecule SIRT2 inhibitor with selective tumor cytotoxicity.

As a member of the class III histone deacetylases, Sirtuin-2 (SIRT2) is critical in cell cycle regulation which makes it a potential target for cancer therapeutics. In this study, we identified a novel SIRT2 inhibitor, AC-93253, with IC(50) of 6 microM in vitro. The compound is selective, inhibiting SIRT2 7.5- and 4-fold more potently than the closely related SIRT1 and SIRT3, respectively. AC-93253 significantly enhanced acetylation of tubulin, p53, and histone H4, confirming SIRT2 and SIRT1 as its cellular targets. AC-93253 as a single agent exhibited submicromolar selective cytotoxicity towards all four tumor cell lines tested with a therapeutic window up to 200-fold, comparing to any of the three normal cell types tested. Results from high content analysis suggested that AC-93253 significantly triggered apoptosis. Taken together, SIRT2 selective inhibitor AC-93253 may serve as a novel chemical scaffold for structure-activity relationship study and future lead development.

Determination of dimethyl fumarate and other potential allergens in desiccant and antimould sachets.

A method for the determination of dimethyl fumarate (DMF), benzothiazole (BT) and tert-butylphenol (TBP) in desiccant and antimould agents employed for protecting consumer products from humidity and mould has been developed. The method is based on ultrasound-assisted extraction (UAE) followed by GC-MS analysis. Parameters that could affect the extraction of the compounds have been optimised using a multivariate approach. In the final conditions, the extraction is performed using only 0.5 or 1 mL ethyl acetate and applying ultrasound energy for 5 min. Simultaneous extractions could also be carried out in 5 min without losing efficiency. The method was validated showing good linearity (R2 >0.995). Both intra- and inter-day precisions were studied at several concentration levels, being satisfactory in all cases (RSD <10%). Recovery was evaluated in four real desiccant samples at different compound concentrations, ranging between 87% and 109%. Limits of detection and quantification were in the low nanogramme per gramme level, thus allowing the determination of DMF at concentrations well below the limit established by the recent EU Directive (0.1 microg/g). The proposed procedure was applied to the determination of the target compounds in several desiccant and antimould samples. Although most of them were simply labelled as "silica gel", more than 70% of the tested samples contained high amounts of DMF, many of them at the high microgram per gramme level. Many samples also showed the presence of the other two potential allergens. These results demonstrate that the content of the "desiccant" sachets and tablets in consumer products does not usually belong with the label of the desiccant, and hence, the high risk of exposition to the powerful allergen DMF and other potentially harmful chemicals through consumer goods should be a matter of concern.

Isolation and Identification of Aryl Hydrocarbon Receptor Modulators in White Button Mushrooms (Agaricus bisporus).

Natural aryl hydrocarbon (AHR) ligands have been identified in food and herbal medicines, and they may exhibit beneficial activity in humans. In this study, white button (WB) feeding significantly decreased AHR target gene expression in the small intestine of both conventional and germ-free mice. High-performance liquid chromatography (HPLC) fractionation and ultra-high-performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) combined with an AHR-responsive cell-based luciferase gene reporter assay were used to isolate and characterize benzothiazole (BT) derivatives and 6-methylisoquinoline (6-MIQ) as AHR modulators from WB mushrooms. The study showed dose-dependent changes of AHR transformation determined by the cell-based luciferase gene reporter assay and transcription of CYP1A1 in human Caco-2 cells by BT derivatives and 6-MIQ. These findings suggested that WB mushroom contains new classes of natural AHR modulators and demonstrated HPLC fractionation and UHPLC-MS/MS combined with a cell-based luciferase gene reporter assay as a useful approach for isolation and characterization of the previously unidentifed AHR modulators from natural products.

A new Met inhibitory-scaffold identified by a focused forward chemical biological screen.

The receptor tyrosine kinase Met is crucial for the genetic program causing cancer progression and metastasis. Its nodal function during aggressiveness and resistance acquisition poses Met inhibition as an obligatory step in anti-cancer targeted therapy. Here, we applied a "Met-focussed" forward chemical biological screen to discover new agents antagonizing Met-triggered biological functions. The identified new scaffold, JLK1360, has a dual mechanism of action towards Met: it impairs Met signalling and also prevents its restoration after degradation. Docking and molecular dynamics provide evidences on the interacting mode of JLK1360 within the Met ATP-binding pocket. Moreover, computational and biochemical studies also highlighted that JLK1360 has a good degree of selectivity towards Met than other RTKs tested. Altogether, these findings demonstrate that the approach we have applied is a powerful strategy to identify compounds with combined properties towards a chosen target. Our studies show how integration of chemistry, biology and computational analysis can provide robust strategies to identify new inhibitory scaffolds suitable for further development of anti-cancer targeted therapies.

[Effect of Temperature on the Performance and Microbial Community Structure in an Integrated Anaerobic Fluidized-bed Membrane Bioreactor Treating Benzothiazole Wastewater].

An integrated anaerobic fluidized-bed membrane bioreactor (IAFMBR) was applied to treat synthetic high-strength benzothiazole wastewater. This study investigated the effect of temperature on the performance, membrane fouling and microbial community structure of IAFMBR. The results showed that decreasing temperature had an adverse effect on the performance and the cycle of membrane fouling. When temperature declined from 35℃ to 15℃, the COD efficiency dropped 7.4%, benzothiazole removal efficiency dropped 49.2%, the accumulation of total VFAs increased 225.66 mg·L-1, and methane yield (in CH4/CODremoved) dropped 0.118 m3·kg-1. The membrane fouling cycle shortened from 5.2 d to 2.5 d. For cake layer, the concentration of soluble microbial product (SMP) increased from 42.47 mg·L-1 to 70.62 mg·L-1, and the extracellular polymeric substance (EPS) content (in VSS) increased from 46.30 mg·g-1 to 82.22 mg·g-1 when the TMP was 15 kPa. For mixed liquor, the concentration of SMP increased from 36.46 mg·L-1 to 69.35 mg·L-1 and the EPS content increased from 47.47 mg·g-1 to 81.63 mg·g-1. Protein was the main component of EPS and SMP, and occurred in proportion of 80%.The microbial community structure showed that the dominant phyla were Firmicutes and Chloroflexi, which accounted for 42.6%-61.0% of the total relative abundance. The genera Clostridium (13.7%), Levilinea (15.2%), and Lactococus (17.9%) dominated with decreasing temperatures. The dominant methanogen was Methanosaeta.

Exoenzymes of Trametes versicolor can metabolize coplanar PCB congeners and hydroxy PCB.

Two fractions containing the oxidase activity toward 2,2'-azinobis (3-ethylbenzothiazoline-6-sulfonate) (ABTS) were obtained using ion-exchange DEAE-Sepharose column chromatography of the culture fluid of white-rot fungus, Trametes versicolor. These two fractions can reduce the level of coplanar PCB congeners (Co-PCBs). The ABTS oxidase in the first fraction passed through the DEAE-Sepharose column. The ABTS oxidase in the second fraction was adsorbed to the column at

Equilibrium and kinetic adsorption study of a cationic dye by a natural adsorbent--silkworm pupa.

In this work the use of silkworm pupa, which is the waste of silk spinning industries has been investigated as an adsorbent for the removal of C.I. Basic Blue 41. The amino acid nature of the pupa provided a reasonable capability for dye removal. Equilibrium adsorption isotherms and kinetics were investigated. The adsorption equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that adsorption behavior of the dye could be described reasonably well by either Langmuir or Freundlich models. The characteristic parameters for each isotherm have been determined. The monolayer adsorption capacity was determined to be 555 mg/g. Kinetic studies indicated that the adsorption follows pseudo-second-order kinetics with a rate constant of 0.0434 and 0.0572 g/min mg for initial dye concentration of 200 mg/l at 20 and 40 degrees C, respectively. Kinetic studies showed that film diffusion and intra-particle diffusion were simultaneously operating during the adsorption process. The rate constant for intra-particle diffusion was estimated to be 1.985 mg/g min(0.5).

Development and validation of a highly sensitive gradient chiral separation of pramipexole in human plasma by LC-MS/MS.

AIM: Development of a high-sensitivity chiral LC-MS/MS method was required to evaluate a combination of pramipexole (S-PPX) and its enantiomer dexpramipexole (R-PPX) in a proposed clinical trial. The previously available methods suffered from low sensitivity for the (S)-enantiomer in the presence of the more abundant (R)-enantiomer. Based on the projected dosing regimen in the clinical trial, a 5000-fold improvement in sensitivity was required for the (S)-enantiomer. METHODOLOGY: Spiked human plasma samples were extracted by liquid-liquid extraction using ethyl acetate and injected onto a CHIRALPAK ID column under pH gradient conditions. CONCLUSION: An improved analytical method was developed and validated with a final LLQ for (S)-PPX of 0.1 ng/ml in the presence of 2000 ng/ml of (R)-PPX.

The cooperative effect of reduced graphene oxide and Triton X-114 on the electromembrane microextraction efficiency of Pramipexole as a model analyte in urine samples.

A new design of electromembrane microextraction coupled with high-performance liquid chromatography was developed for the determination of Pramipexole as a model analyte in urine samples. The presence of reduced graphene oxide in the membrane and Triton X-114 in the donor phase augments the extraction efficiency of Pramipexole by the proposed method. Dispersed reduced graphene oxide in the organic solvent was held in the pores of the fiber wall by capillary forces and sonication. It is possible that the immobilized reduced graphene oxide acts as a sorbent, affording an additional pathway for analyte transportation. Besides, the presence of Triton X-114 in the donor phase promotes effective migration of ionic analytes across the membrane. The parameters influencing the extraction procedure, such as type and concentration of surfactant, type of organic solvent, amount of reduced graphene oxide, sonication time, applied voltage, extraction time, ionic strength, pH of the donor and acceptor solutions, and stirring rate were optimized. The linear working ranges of the method for preconcentration- determination of Pramipexole in water and urine samples were found to be 0.13-1000 and 0.47-1000ngmL-1 with corresponding detection limits of 0.04 and 0.14ngmL-1, respectively. The proposed method allows achieving enrichment factors of 301 and 265 for preconcentration of the analyte in water and urine samples, respectively. The method was successfully applied for the determination of Pramipexole in the urine samples.