In-house validation of an LC-MS method for the multiplexed quantitative determination of total allergenic food in chocolate.

Mass spectrometry has been widely accepted as a confirmatory tool for the sensitive detection of undeclared presence of allergenic ingredients. Multiple methods have been developed so far, achieving different levels of sensitivity and robustness, still lacking harmonization of the analytical validation and impairing comparability of results. In this investigation, a quantitative method has been validated in-house for the determination of six allergenic ingredients (cow's milk, hen's egg, peanut, soybean, hazelnut, and almond) in a chocolate-based matrix. The latter has been produced in a food pilot plant to provide a real and well-characterized matrix for proper assessment of method performance characteristics according to official guidelines. In particular, recent considerations issued by the European Committee for Standardization have been followed to guide a rigorous single-laboratory validation and to feature the main method performance, such as selectivity, linearity, and sensitivity. Synthetic surrogates of the peptide markers have been used both in native and labelled forms in matrix-matched calibration curves as external calibrants and internal standards, respectively. A two-order of magnitude range was investigated, focusing on the low concentration range for proper assessment of the detection and quantification limits (LOD and LOQ) by rigorous calibration approach. Conversion factors for all six allergenic ingredients have been determined for the first time to report the final quantitative information as fraction of total allergenic food protein (TAFP) per mass of food (µgTAFP/gfood), since such a reporting unit is exploitable in allergenic risk assessment plans. The method achieved good sensitivity with LOD values ranging between 0.08 and 0.2 µgTAFP/gfood, for all ingredients besides egg and soybean, whose quantitative markers reported a slightly higher limit (1.1 and 1.2 µgTAFP/gfood, respectively). Different samples of chocolate bar incurred at four defined concentration levels close to the currently available threshold doses have been analyzed to test the quantitative performance of the analytical method, with a proper estimate of the measurement uncertainty from different sources of variability. The sensitivity achieved resulted in compliance with the various threshold doses issued or recommended worldwide.

Chemical Composition of Fat Bloom on Chocolate Products Determined by Combining NMR and HPLC-MS.

To reduce unwanted fat bloom in the manufacturing and storage of chocolates, detailed knowledge of the chemical composition and molecular mobility of the oils and fats contained is required. Although the formation of fat bloom on chocolate products has been studied for many decades with regard to its prevention and reduction, questions on the molecular level still remain to be answered. Chocolate products with nut-based fillings are especially prone to undesirable fat bloom. The chemical composition of fat bloom is thought to be dominated by the triacylglycerides of the chocolate matrix, which migrate to the chocolate's surface and recrystallize there. Migration of oils from the fillings into the chocolate as driving force for fat bloom formation is an additional factor in the discussion. In this work, the migration was studied and confirmed by MRI, while the chemical composition of the fat bloom was measured by NMR spectroscopy and HPLC-MS, revealing the most important triacylglycerides in the fat bloom. The combination of HPLC-MS with NMR spectroscopy at 800 MHz allows for detailed chemical structure determination. A rapid routine was developed combining the two modalities, which was then applied to investigate the aging, the impact of chocolate composition, and the influence of hazelnut fillings processing parameters, such as the degree of roasting and grinding of the nuts or the mixing time, on fat bloom formation.

Challenges and potential for detecting and quantifying titanium dioxide in food.

BACKGROUND: Titanium dioxide (TiO2) is banned in some countries but its use is still permitted in others. The global food supply chain is therefore challenged with the need to use rapid and reliable testing methods to either detect the presence of TiO2 or to quantify its concentration. The goal of this study was to determine the feasibility of using color, texture profile analysis, Raman microscopy, and X-ray fluorescence (XRF) spectroscopy to detect and quantify TiO2 in fillings used in the pastry and confectionery industry. In this study, two types of fillings were investigated: vanilla based and chocolate based. All fillings were prepared in four different variations - without TiO2 and with three concentrations as follows: 0.25 g*kg-1, 0.5 g*kg-1, or 0.75 g*kg-1 TiO2 per sample. The methods were selected for their ability to analyze the samples in a short period of time. RESULTS: All of the methods showed moderate to high potential for detecting TiO2 in the samples. The results reveal how TiO2 affects the food matrix color and texture. Use of Raman microscopy confirms its detectability, although concentrations of TiO2 do not follow a pattern. X-ray fluorescence spectroscopy showed the greatest potential as it can not only detect TiO2 but can also quantify its concentration in the samples. CONCLUSIONS: The highest potential for quantifying the concentration of this food additive was achieved with XRF. © 2024 Society of Chemical Industry.

One-bite-sized 3D printed finger foods, oriented to malnutrition, sarcopenia and frailty prevention in the older people.

BACKGROUND: In this study, innovative chocolate, citrus and mixture flavoured tofu-based nutritionally customised, dysphagia-oriented, comfortably consumed, appetising, one-bite-sized finger foods, oriented to malnutrition, sarcopenia and frailty prevention in older people were created by using 3D printing technology. Developed products were characterised by evaluating chemical composition and physical properties and performing sensory evaluation among geriatric clinic residents (≥60 years). RESULTS: The dietary composition of the developed foods was: 19-21 g (100 g)-1 protein, 6-8 g (100 g)-1 fibre, 8-9 g (100 g)-1 fat, 11 mg (100 g)-1 iron, 14 mg (100 g)-1 zinc, 70 µg (100 g)-1 selenium. Foods were also enriched with branched-chain amino acids, such as leucine, isoleucine and valine. All formulated foods were classified as level 6 by International Dysphagia Diet Standardisation Initiative classification. Chocolate-flavoured food was much harder (4914 g) with lower adhesiveness value (-33.6 g s), compared to the citrus- or mixture-flavoured foods. Older people evaluated all finger foods as very easy handled by hand, soft, easy to swallow, having a moderate flavour intensity and a weak afterfeel. Despite the fact that the chocolate food was evaluated as having the highest hardness and gumminess values by the instrumental method, this difference was not noticeable to the evaluators. However 7% of the participants said that 3D printed foods were sticky to dentures. CONCLUSION: The results suggest that it is possible to create nutrient-dense comfortably consumed 3D printed foods, oriented to malnutrition, sarcopenia and frailty prevention in older people. © 2024 Society of Chemical Industry.

A novel kinetic model for a cocoa waste fermentation to ethanol reaction and its experimental validation.

A non-segregated kinetic model is proposed to describe a fermentation process of agro-industrial residues derived via cocoa (mucilage juice) by Pichia kudriavzevii. The novel proposed hybrid model is based on a multiple coupling reaction mechanisms (structured) to describe the kinetics of substrate consumption, biomass, carbon dioxide, and ethanol, coupled to an unstructured model for the activity enzyme. The parameters of the kinetic model are estimated by non-linear least-squares curve fitting using the Marquardt-Levenberg algorithm. In addition, numerical simulations were compared with the experimental data via residual graphs. The effectiveness of the model was statistically evaluated using dimensionless efficiency coefficients under different initial conditions. A global sensitivity analysis was applied (Fisher's information matrix). The experimental results of the batch reactor showed a maximum ethanol concentration of 29 g/L, with a yield of 0.48 g-ethanol/g-glucose and a productivity of 0.30 g/L h. The method determined that the cell formation coefficient and the specific substrate consumption rate (θ1 and θ2) directly influence most of the states of our system. The proposed scheme is particularly suitable to assist in the rational design of cell factory properties or fermentation processes because it can represent the complex biochemistry in more detail and under different initial experimental conditions; the above reveals that the generated model is robust and can be considered for control and optimization purposes.

Link between Flavor Perception and Volatile Compound Composition of Dark Chocolates Derived from Trinitario Cocoa Beans from Dominican Republic.

The chemical composition of dark chocolate has a significant impact on its complex flavor profile. This study aims to investigate the relationship between the volatile chemical composition and perceived flavor of 54 dark chocolate samples made from Trinitario cocoa beans from the Dominican Republic. The samples were evaluated by a trained panel and analyzed using gas chromatography-mass spectrometry (GC-MS) to identify and quantify the volatile compounds. Predictive models based on a partial least squares regression (PLS) allowed the identification of key compounds for predicting individual sensory attributes. The models were most successful in classifying samples based on the intensity of bitterness and astringency, even though these attributes are mostly linked to non-volatile compounds. Acetaldehyde, dimethyl sulfide, and 2,3-butanediol were found to be key predictors for various sensory attributes, while propylene glycol diacetate was identified as a possible marker for red fruit aroma. The study highlights the potential of using volatile compounds to accurately predict chocolate flavor potential.

Traceability, authenticity and sustainability of cocoa and chocolate products: a challenge for the chocolate industry.

Cocoa beans, the seeds of the tree Theobroma cacao L., are the key raw material for chocolate production that implies an extensive post-harvest process. Chocolate properties can vary depending on cocoa origin, composition and manufacturing procedure, which will give unique sensory properties to the final product. On the other hand, the high global consumption of cocoa products, long recognized as a major source of dietary polyphenols with important health benefits, has increased interest in tracking the geographical origin of cocoa and authenticating chocolate to guarantee product quality and reveal possible commercial fraud. However, the sustainable production of high-quality cocoa is still far from reality, and the cocoa sector continues to face many challenges in this field. This review provides an update on the progress toward the authenticity, traceability and sustainability of cocoa products, issues that chocolate producers still need to resolve.

Heat resistant chocolate development for subtropical and tropical climates: a review.

Heat resistant chocolate (HRC) which can retain the desired texture and mouthfeel in tropical and subtropical climatic conditions has become a major research area in the chocolate industry. Liking of the chocolate products keeps on changing with the geographical conditions of the world due to the availability of ingredients from local resources and consumer's taste preferences. The geographical changes also bring about the change in climatic conditions and as such no chocolates have been formulated to withstand the hot tropical or sub-tropical temperature conditions. Textural issues and various storage related problems faced due to meltability of chocolate in different countries has opened up a broad research field of sustainable HRC manufacturing. Over the years, there are broadly three different approaches (fat modification, sugar structure modification and innovative process approach) to develop the HRC and all these scientific approaches have given different scientific insights about improving the heat resistance characteristics and textural stability of chocolate. There is a lack or coordinated fundamental and applied research related to cocoa butter polymorphism, and thermal-textural issues during product development/storage. This review paper is an attempt to describe the different scientific approaches for developing HRC and how they affect the physical/sensory chocolate attributes.

Development of incurred chocolate bars and broth powder with six fully characterised food allergens as test materials for food allergen analysis.

The design and production of incurred test materials are critical for the development and validation of methods for food allergen analysis. This is because production and processing conditions, together with the food matrix, can modify allergens affecting their structure, extractability and detectability. For the ThRAll project, which aims to develop a mass spectrometry-based reference method for the simultaneous accurate quantification of six allergenic ingredients in two hard to analyse matrices. Two highly processed matrices, chocolate bars and broth powder, were selected to incur with six allergenic ingredients (egg, milk, peanut, soy, hazelnut and almond) at 2, 4, 10 and 40 mg total allergenic protein/kg food matrix using a pilot-scale food manufacturing plant. The allergenic activity of the ingredients incurred was verified using food-allergic patient serum/plasma IgE, the homogeneity of the incurred matrices verified and their stability at 4 °C assessed over at least 30-month storage using appropriate enzyme-linked immunosorbent assays (ELISA). Allergens were found at all levels from the chocolate bar and were homogenously distributed, apart from peanut and soy which could only be determined above 4 mg total allergenic ingredient protein/kg. The homogeneity assessment was restricted to analysis of soy, milk and peanut for the broth powder but nevertheless demonstrated that the allergens were homogeneously distributed. All the allergens tested were found to be stable in the incurred matrices for at least 30 months demonstrating they are suitable for method development.

Effects of cocoa-rich chocolate on cognitive performance in postmenopausal women. A randomised clinical trial.

OBJECTIVES: The aim of this research was to evaluate the effects of adding 10 g of cocoa-rich chocolate (99%) to the habitual diet on cognitive performance in postmenopausal women. METHODS: Following a randomised controlled parallel clinical trial, a total of 140 postmenopausal women aged 50-64 were recruited. The intervention group (n = 73) consumed daily 10 g of chocolate (99% cocoa) in addition to their usual food intake for 6 months, whereas the control group (n = 67) did not receive any intervention. Attention and executive functions, verbal memory, working memory, phonological fluency, category fluency and clinical variables were assessed at baseline and 6 months. RESULTS: Trail Making Test B execution time showed a decreased of -12.08 s (95% CI: -23.99, -0.18; p = 0.047) in the intervention group compared to the control group, after adjusting for age, educational level, time elapsed from the beginning of menopause and daily energy consumption (Cohen's d = -0.343). Attention, immediate or delayed verbal memory, phonological or category fluency, and working memory remained unchanged. CONCLUSIONS: The consumption of cocoa-rich (99%) chocolate in addition to the habitual diet could be related to a slight improvement in cognitive performance regarding cognitive flexibility and processing speed in postmenopausal women, with no changes in the rest of the cognitive performance variables evaluated.Trial registration: This clinical trial has been registered at clinicaltrials.gov as NCT03492983.

Fast Detection of Cadmium in Chocolate by Solid Sampling Electrothermal Vaporization Atomic Absorption Spectrometry and Its Application on Dietary Exposure Risk Assessment.

In this work, a rapid detection method using solid sampling electrothermal vaporization atomic absorption spectrometry (SS-ETV-AAS) was established for cadmium in chocolate. The instrumental system includes a solid sampling ETV unit, a catalytic pyrolysis furnace, an AAS detector, and a gas supply system with only an air pump and a hydrogen generator. Herein, MgO material with 1.0−1.5 mm particle size was first employed to replace the kaolin filler previously used to further shorten the peak width and to thereby improve the sensitivity. With 350 mL/min of air, a chocolate sample was heated for 25 s from 435 to 464 °C to remove water and organic matrices; then, after supplying 240 mL/min hydrogen and turning down air to 120 mL/min, a N2/H2 mixture gas was formed to accelerate Cd vaporization from chocolate residue under 465 to 765 °C. Under the optimized conditions, the detection limit (LOD) was obviously lowered to 70 pg/g (vs. previous 150 pg/g) with R2 > 0.999; the relative standard deviations (RSD) of repeated measurements for real chocolate samples ranged from 1.5% to 6.4%, indicating a favorable precision; and the Cd recoveries were in the range of 93−107%, proving a satisfied accuracy. Thus, the total analysis time is less than 3 min without the sample digestion process. Thereafter, 78 chocolate samples with different brands from 9 producing countries in China market were collected and measured by this proposed method. Based on the measured Cd concentrations, a dietary exposure assessment was performed for Chinese residents, and the target hazard quotient (THQ) values are all less than 1, proving no significant health risk from intaking chocolate cadmium for Chinese residents.

Screening Wild Yeast Isolated from Cocoa Bean Fermentation Using Volatile Compounds Profile.

Yeasts are one of the main ingredients responsible for flavor precursors production associated with sensorial characteristics in chocolate. Using wild yeast isolated from cocoa beans fermentation is emerging as a strategy for developing starter cultures. However, the volatile compounds (VCs) produced by yeasts are not yet known. This study aimed to select wild yeasts with the potential to produce volatile compounds associated with desirable flavor attributes. A total of 150 wild yeasts strains were isolated from the spontaneous cocoa beans fermentation, of which 40 were identified by morphology and physiological features. VCs produced were identified and quantified using SPME-GC-MS and GC-FID and profiles were evaluated statistically by PCA and cluster analysis for the compounds that had a high odor threshold value. Thirty-six VCs produced by these yeasts were identified into six main families, namely esters, alcohols, acids, aldehydes, ketones, and pyrazines. PCA showed the separation of the yeasts into two main clusters. Strains, Y195 and Y246, belong to the first cluster and are the highest producers of alcohols related to floral perceptions. In the second cluster, thirty-three yeasts were grouped by their ability to produce esters. Of all of them, Y110MRS stood out for producing 2-phenyl ethyl acetate and isoamyl acetate associated with fruity perceptions. This screening allowed us to identify yeasts that produced VCs of technological interest and which could be used to develop a starter culture.

Impacts of cocoa pod maturity at harvest and bean fermentation period on the production of chocolate with potential health benefits.

BACKGROUND: Cacao beans are rich sources of polyphenols with an abundance of flavonoids and methylxanthines that have positive influences on human health. The main factors affecting the formation of flavor as well as the chemical and bioactive composition of cacao beans are cacao pod maturity and post-harvest fermentation. The purpose of this research was to evaluate the effects of pod harvest maturity (mature and ripe) and post-fermentation period (1, 3, and 5 days in a controlled temperature environment) measured by pre-harvest maturity indices, post-harvest quality tests, chemical measurements, and organoleptic evaluation. RESULTS: As pods developed, flavonol accumulated while nitrogen content degraded. Mature pods produced beans with a higher flavonol, catechin, and total phenolic content (TPC). As fermentation progressed, the beans' fat, TPC, antioxidant activity, and catechin content increased, regardless of pod maturity at harvest. Free fatty acid (FFA) levels were highest in 5 day fermented beans. The 3 day fermented beans contained significantly higher epicatechin, with lower FFA content. Chocolate made from mature beans with 3 day fermentation was more pleasant as it scored the highest in flavor intensity and complexity and the lowest in acidity and astringency. CONCLUSION: This study suggests that cacao pods harvested at the mature stage with further fermentation for 3 days under controlled temperatures produce specialty beans with potential health benefits. © 2021 Society of Chemical Industry.

Metagenome-Assembled Genomes Contribute to Unraveling of the Microbiome of Cocoa Fermentation.

Metagenomic studies about cocoa fermentation have mainly reported on the analysis of short reads for determination of operational taxonomic units. However, it is also important to determine metagenome-assembled genomes (MAGs), which are genomes deriving from the assembly of metagenomics. For this research, all the cocoa metagenomes from public databases were downloaded, resulting in five data sets: one from Ghana and four from Brazil. In addition, in silico approaches were used to describe putative phenotypes and the metabolic potential of MAGs. A total of 17 high-quality MAGs were recovered from these microbiomes, as follows: (i) for fungi, Yamadazyma tenuis (n = 1); (ii) lactic acid bacteria, Limosilactobacillus fermentum (n = 5), Liquorilactobacillus cacaonum (n = 1), Liquorilactobacillus nagelli (n = 1), Leuconostoc pseudomesenteroides (n = 1), and Lactiplantibacillus plantarum subsp. plantarum (n = 1); (iii) acetic acid bacteria, Acetobacter senegalensis (n = 2) and Kozakia baliensis (n = 1); and (iv) Bacillus subtilis (n = 1), Brevundimonas sp. (n = 2), and Pseudomonas sp. (n = 1). Medium-quality MAGs were also recovered from cocoa microbiomes, including some that, to our knowledge, were not previously detected in this environment (Liquorilactobacillus vini, Komagataeibacter saccharivorans, and Komagataeibacter maltaceti) and others previously described (Fructobacillus pseudoficulneus and Acetobacter pasteurianus). Taken together, the MAGs were useful for providing an additional description of the microbiome of cocoa fermentation, revealing previously overlooked microorganisms, with prediction of key phenotypes and biochemical pathways. IMPORTANCE The production of chocolate starts with the harvesting of cocoa fruits and the spontaneous fermentation of the seeds in a microbial succession that depends on yeasts, lactic acid bacteria, and acetic acid bacteria in order to eliminate bitter and astringent compounds present in the raw material, which will be further roasted and grinded to originate the cocoa powder that will enter the food processing industry. The microbiota of cocoa fermentation is not completely known, and yet it advanced from culture-based studies to the advent of next-generation DNA sequencing, with the generation of a myriad of data that need bioinformatic approaches to be properly analyzed. Although the majority of metagenomic studies have been based on short reads (operational taxonomic units), it is also important to analyze entire genomes to determine more precisely possible ecological roles of different species. Metagenome-assembled genomes (MAGs) are very useful for this purpose; here, MAGs from cocoa fermentation microbiomes are described, and the possible implications of their phenotypic and metabolic potentials are discussed.

Analysis of the California list of pesticides, mycotoxins, and cannabinoids in chocolate using liquid chromatography and low-pressure gas chromatography-based platforms.

Cannabis legalization has led to the development of a variety of cannabis-infused products with edibles being one of the most popular. The state of California has implemented comprehensive cannabis testing regulations requiring the analysis of cannabinoids (potency) and contaminants, such as pesticides and mycotoxins, in any type of cannabis good. In this work, we propose an analytical workflow for the quantification of the California list of pesticides and mycotoxins, as well as six cannabinoids, in chocolate, using 3 mL of solvent for the extraction. For the analysis of pesticides and mycotoxins, clean-up steps employing a C18 solid-phase extraction cartridge and dispersive solid-phase extraction sorbents were implemented. Gas chromatography amenable pesticides were analyzed using low-pressure gas chromatography coupled to tandem mass spectrometry which allowed for a total method run of 12 min. Both liquid chromatography and gas chromatography instrumental methods had the same analysis time, ensuring satisfactory sample throughput. For the determination of cannabinoids, a dilution of the original organic extract collected for pesticides and mycotoxins analysis (and prior to any clean-up step) was used. Excellent results in terms of analytical figures of merit were obtained for all target analytes.

Fluorimetric Analysis of Five Amino Acids in Chocolate: Development and Validation.

Amino acids present ergogenic action, helping to increase, protect, and restore the muscular system of young athletes. Moreover, the encapsulation of five relevant amino acids in chocolate pellet form will appeal to them, facilitating their daily consumption. A reliable HPLC fluorimetric method was developed to detect and quantitatively determine L-Leucine, L-Isoleucine, L-Histidine, L-Valine, and ß-Alanine in chocolate using aniline as an internal standard. Experimental design methodology was used to investigate and optimize the clean-up procedure of the samples. Therefore, three extraction techniques (solid-phase extraction (by two different SPE cartridges) and liquid-solid extraction (LSE)) were compared and evaluated. The LOQ values in chocolate varied from 24 to 118 ng/g (recovery 89.7-95.6%, %RSD < 2.5). Amino acids were pre-column derivatized with o-phthalaldehyde (OPA), while derivatization parameters were thoroughly investigated by experimental design methodology. The analysis was performed by HPLC-fluorescence (emission: λ = 455 nm, excitation: λ = 340 nm) method using a C18 column and a mixture of phosphate buffer (pH = 2.8; 20 mM)-methanol as a mobile phase in gradient elution. The method was validated (r2 > 0.999, %RSD < 2, LOD: 10 ng mL-1 for histidine and leucine, 2 ng mL-1 for alanine and valine, and 4 ng mL-1 for Isoleucine) according to the International Conference on Harmonization guidelines.

White Chocolate with Resistant Starch: Impact on Physical Properties, Dietary Fiber Content and Sensory Characteristics.

Resistant starch (RS) is a part of insoluble dietary fiber, and it could be recognized as a functional food ingredient in some types of confectionery products that lack dietary fiber. Unlike dark and milk chocolate, white chocolate does not contain fat-free cocoa solids rich in dietary fiber. In the present study, 5%, 10%, and 15% of white chocolate were substituted with RS in order to improve the nutritional value of enriched white chocolate. The influence of RS on rheological, textural, and thermal properties of the chocolate fat phase was firstly investigated, and then further influence on physical properties, dietary fiber content, and sensory characteristics of enriched white chocolates were investigated. The obtained results showed that enriched chocolates had increased content of total dietary fiber and reduced total fats and protein content in accordance with the added amount of RS. At the same time, RS increased viscosity and reduced the hardness and volume mean diameter in enriched chocolates in accordance with the added amount. RS improved the nutritional composition of white chocolate by increasing the content of dietary fiber. At the same time, RS did not impair the color and sensory characteristics of enriched white chocolates.

Profile of Volatile Compounds of On-Farm Fermented and Dried Cocoa Beans Inoculated with Saccharomyces cerevisiae KY794742 and Pichia kudriavzevii KY794725.

This study aimed to identify the volatile compounds in the fermented and dried cocoa beans conducted with three distinct inoculants of yeast species due to their high fermentative capacity: Saccharomyces cerevisiae, Pichia kudriavzevii, the mixture in equal proportions 1:1 of both species, and a control fermentation (with no inoculum application). Three starter cultures of yeasts, previously isolated and identified in cocoa fermentation in the municipality of Tomé-Açu, Pará state, Brazil. The seeds with pulp were removed manually and placed in wooden boxes for the fermentation process that lasted from 6 to 7 days. On the last day of fermentation, the almonds were packaged properly and placed to dry (36 °C), followed by preparation for the analysis of volatile compounds by GC-MS technique. In addition to the control fermentation, a high capacity for the formation of desirable compounds in chocolate by the inoculants with P. kudriavzevii was observed, which was confirmed through multivariate analyses, classifying these almonds with the highest content of aldehydes, esters, ketones and alcohols and low concentration of off-flavours. We conclude that the addition of mixed culture starter can be an excellent alternative for cocoa producers, suggesting obtaining cocoa beans with desirable characteristics for chocolate production, as well as creating a product identity for the producing region.

Physicochemical, Antioxidant, Microstructural Properties and Bioaccessibility of Dark Chocolate with Plant Extracts.

In this study, dark chocolates (DCh) containing zinc lactate (ZnL) were enriched with extracts from elderberries (EFrE), elderflowers (EFlE), and chokeberries (ChFrE) to improve their functional properties. Both dried plant extracts and chocolates were analyzed for antioxidant capacity (AC) using four different analytical methods: 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), cupric ion-reducing antioxidant capacity (CUPRAC), and ferric-reducing antioxidant power (FRAP), while total phenolic content (TPC) was determined by Folin-Ciocalteu (F-C) assay. An increase in antioxidant properties of fortified chocolates was found, and the bioaccessibility of their antioxidants was evaluated. The highest AC and TPC were found in ChFrE and chocolate with chokeberries (DCh + ChFrE) before and after simulated in vitro digestion. Bioaccessibility studies indicated that during the simulated digestion the AC of all chocolates reduced significantly, whereas insignificant differences in TPC results were observed between chemical and physiological extracts. Moreover, the influence of plant extracts on physicochemical parameters such as moisture content (MC), fat content (FC), and viscosity of chocolates was estimated. Furthermore, scanning electron microscopy with dispersive energy spectroscopy (SEM-EDS) was used to analyze surface properties and differences in the chemical composition of chocolates without and with additives.

Comparison of the Effects of Conching Parameters on the Contents of Three Dominant Flavan3-ols, Rheological Properties and Sensory Quality in Chocolate Milk Mass Based on Liquor from Unroasted Cocoa Beans.

The content of polyphenols in chocolate depends on many factors related to the properties of raw material and manufacturing parameters. The trend toward developing chocolates made from unroasted cocoa beans encourages research in this area. In addition, modern customers attach great importance to how the food they consume benefits their bodies. One such benefit that consumers value is the preservation of natural antioxidant compounds in food products (e.g., polyphenols). Therefore, in our study we attempted to determine the relationship between variable parameters at the conching stage (i.e., temperature and time of) and the content of dominant polyphenols (i.e.,catechins, epicatechins, and procyanidin B2) in chocolate milk mass (CMM) obtained from unroasted cocoa beans. Increasing the conching temperature from 50 to 60 °C decreased the content of three basic flavan-3-ols. The highest number of these compounds was determined when the process was carried out at 50 °C. However, the time that caused the least degradation of these compounds differed. For catechin, it was 2 h; for epicatechin it was 1 h; and for procyanidin it was 3 h. The influence of both the temperature and conching time on the rheological properties of chocolate milk mass was demonstrated. At 50 °C, the viscosity and the yield stress of the conched mass showed its highest value.