Comparison of the Efficiency of Two Novel Guided Bone Regeneration Devices in the Rabbit Calvarial Model.

BACKGROUND: Creating a secluded large space using guided bone regeneration (GBR) is a novel osteogenesis technique used in the prevention of premature membrane exposure complications. However, this technique is not considered clinically feasible. OBJECTIVES: This study aimed to compare the outcome of the insertion of two novel GBR devices in a rabbit calvarial model in terms of mode of action, simplicity, and amount of new space and bone gained. MATERIALS AND METHODS: The expansible GBR (EGBR) device, composed mainly of a titanium plate, silicone membrane, and activation screw, was inserted beneath the periosteum in the calvarial area of eight rabbits. The smart GBR (SGBR) device, composed of silicone sheets and Nitinol strips, were inserted beneath the periosteum in the calvarial area of another 10 rabbits. Half of each group was sacrificed 2 months after surgery, and the other half was sacrificed after 4 months. RESULTS: Histological and microradiographical analysis showed that, at 2 months, the EGBR device achieved a mean space gain of 207.2 mm3, a mean bone volume of 68.2 mm3, and a mean maximum bone height of 1.9 mm. Values for the same parameters at 4 months were 202.1 mm3, 70.3 mm3, and 1.6 mm, respectively. The SGBR device had significantly higher (P < 0.05) mean space gain (238.2 mm3; 239.5 mm3), bone volume (112.9 mm3, 107.7 mm3), and bone height (2.7 mm; 2.6 mm) than the EGBR device at 2 and 4 months, respectively. CONCLUSION: Both devices proved to be effective in augmenting bone vertically through the application of GBR and soft tissue expansion processes. However, the SGBR device was more efficient in terms of mode of action, simplicity, and amount of bone created in the new space.

Comparison of two reinforcement rings for primary total hip arthroplasty addressing displaced acetabular fractures: a biomechanical analysis.

INTRODUCTION: Aim of this study was to biomechanically compare two different acetabular cup fixation constructs in terms of fracture fixation for displaced acetabular fractures involving the anterior column with hemitransverse fracture under partial and full weight-bearing conditions. METHODS: Two different reinforcement rings designed as cages for primary THA were biomechanically tested in terms of managing a complex acetabular fracture. Single-leg stance cyclic loading was performed to assess fracture gap movement and fragment rotation. Twelve hemi pelvis Sawbones were divided into two groups: primary THA with acetabulum roof reinforcement plate (ARRP) (n = 6) and primary THA with Burch-Schneider reinforcement cage (BSRC) (n = 6). RESULTS: During loading under partial weight-bearing (250 N) fracture gap movement tended to be larger in the BSRC group as compared to the ARRP group. Under full weight-bearing conditions, the ARRP showed 60% significantly less motion (p = 0.035) of the os ilium to os ischii gap compared to BSRC. Fracture gap movements between the os ilium and spina iliaca fragments were significantly reduced by 76% (p = 0.048) for ARRP in contrast to BSRC. The ARRP group also demonstrated significantly less movement in the fracture gaps os ischii to quadrilateral plate (62% reduction, p = 0.009) and quadrilateral plate to spina iliaca (87% reduction, p < 0.001). Significantly less rotational movement of the quadrilateral plate to the os ilium was exhibited by the ARRP group (p = 0.015). CONCLUSIONS: The presented acetabulum roof-reinforcement plate (ARRP) provides stable conditions at the acetabular component with adequate stabilization of a displaced acetabular fracture.

Comparison of the efficacy of a distal clavicular locking plate with and without a suture anchor in the treatment of Neer IIb distal clavicle fractures.

BACKGROUND: To compare the clinical outcomes between the use of a distal clavicular locking plate alone and the combined use of a plate and a coracoclavicular suture anchor in the treatment of Neer IIb distal clavicle fractures and to discuss the application procedure of suture anchors. METHODS: This is a retrospective study. Thirty-four patients with unilateral Neer IIb distal clavicle fractures who underwent open reduction and internal fixation with a distal clavicular locking plate only (16 patients) or with both a plate and a coracoclavicular suture anchor (18 patients) were evaluated. The main observation data included the Constant-Murley Shoulder Function Score (CMS), rate of postoperative complications, and union time. RESULTS: The distal clavicular locking plate and coracoclavicular suture anchor combination group had better outcomes in the Constant-Murley score (94.6 ± 4.5 vs. 90.1 ± 9.5) (P < 0.05) and a shorter union time (13.9 ± 2.3 vs. 16.1 ± 3.0) (P < 0.05) than the locking plate only group did, and the rate of complications showed no significant difference, 16.7% vs. 31.2% (5/16) (P>0.05). CONCLUSIONS: Both methods achieved good results in the treatment of Neer IIb distal clavicle fractures; however, the use of both locking plates and coracoclavicular suture anchors can provide more stability in the early stage after operation than can the use of locking plates alone, which can make the sped of union quicker and result in better clinical outcomes. For elderly patients with comminuted Neer IIb distal clavicle fractures, a locking plate combined with a suture anchor is recommended to provide more stability in the early stage after the operation.

Ex Vivo Biomechanical Comparison of Titanium Locking Plate, Stainless Steel Nonlocking Plate, and Tie-in External Fixator Applied by a Dorsal Approach on Ostectomized Humeri of Pigeons (Columba livia).

To compare the bending strength of a locking plate (LP), nonlocking plate (NLP), and an external skeletal fixator intramedullary pin (ESF-IM) tie-in fixation applied by a dorsal approach in an avian humerus fracture model, 5 left humeri obtained from pigeon (Columba livia) cadavers were randomly assigned to each repair technique (n = 15). The ESF-IM group was repaired with a 0.062-inch intramedullary pin tied-in with two 0.035-inch positive profile transfixation pins using acrylic filled plastic tubing. The LP group was repaired with a dorsally applied titanium 1.6-mm screw 7-hole locking plate (1 bicortical and 2 monocortical screws in each segment). The NLP group was repaired with a dorsally applied 6-hole stainless steel 1.5-mm dynamic compression plate (all bicortical screws). All constructs were applied before complete ostectomy to allow perfect reconstruction. Constructs were cyclically tested nondestructively for 1000 cycles in four-point bending before being tested to failure. Outcome measures included stiffness, strength, and strain energy. All specimens cycled without failure. The ESF-IM specimens were significantly stiffer and stronger than the plated repair groups. Plated constructs had significantly higher strain energies than ESF-IM. LP and NLP were of equal stiffness, strength, and strain energies. This study demonstrated that bending biomechanical properties of the ESF-IM configuration were superior to those of the dorsal plate fixation. Exact properties of fixation required to facilitate avian fracture healing are largely unknown. Further study, including assessments of optimal plate position and configuration, and torsional and in vivo studies in avian species are warranted.

Retrospective evaluation of perioperative and short term clinical outcomes in appendicular long bone skeleton fractures repaired via the string of pearls (SOP) locking plate system.

BACKGROUND: Internal plate fixation and, more recently, locking plate fixation are commonly used in the repair of fractures in small animal surgery. This retrospective study reviewed the use of the String of Pearls locking plate system in the fixation/repair of appendicular long bone skeleton fractures in 31 small animal veterinary patients (33 fractures). RESULTS: Major complications necessitating revision surgery occurred in 7/33 (21%), with implant failure as the inciting cause in all cases. Variables corresponding to an unsuccessful outcome were evaluated, and a correlation was found with plates placed in a bridging manner (placed without rigid anatomic reconstruction, p = 0.02) and length of follow-up (p = 0.01). CONCLUSIONS: The SOP plating system can be used in the repair of appendicular longbone skeletal fractures, however, the authors propose that adjunct fixation, such as intramedullary pin, double plating, or external coaptation would likely improve results and should be considered imperative in cases in which anatomic reconstruction is either not desirable or achievable.

Biomechanical comparison of screw-based zoning of PHILOS and Fx proximal humerus plates.

BACKGROUND: Treatment of proximal humerus fractures with locking plates is associated with complications. We aimed to compare the biomechanical effects of removing screws and blade of a fixed angle locking plate and hybrid blade plate, on a two-part fracture model. METHODS: Forty-five synthetic humeri were divided into nine groups where four were implanted with a hybrid blade plate and the remaining with locking plate, to treat a two-part surgical neck fracture. Plates' head screws and blades were divided into zones based on their distance from fracture site. Two groups acted as a control for each plate and the remaining seven had either a vacant zone or blade swapped with screws. For elastic cantilever bending, humeral head was fixed and the shaft was displaced 5 mm in extension, flexion, valgus and varus direction. Specimens were further loaded in varus direction to investigate their plastic behaviour. RESULTS: In both plates, removal of inferomedial screws or blade led to a significantly larger drop in varus construct stiffness than other zones. In blade plate, insertion of screws in place of blade significantly increased the mean extension, flexion valgus and varus bending stiffness (24.458%/16.623%/19.493%/14.137%). In locking plate, removal of screw zones proximal to the inferomedial screws reduced extension and flexion bending stiffness by 26-33%. CONCLUSIONS: Although medial support improved varus stability, two inferomedial screws were more effective than blade. Proximal screws are important for extension and flexion. Mechanical consequences of screw removal should be considered when deciding the number and choice of screws and blade in clinic.

A new anatomic locking plate for the treatment of posterolateral tibial plateau fractures.

BACKGROUND: Posterolateral tibial plateau fractures have become more common, and their treatment is of great importance to knee function. Additionally, there is no available literature detailing specialized anatomic locking plate for tibial plateau fractures. Therefore, the aim of the study was to evaluate the safety and clinical efficacy of an innovative anatomic locking plate for treatment of posterolateral tibial plateau fractures. METHODS: Between March 2014 and January 2016, 12 patients with posterolateral tibial plateau fracture underwent surgery with the anatomic locking plate for the posterolateral tibial plateau via the posterolateral approach. Relevant operational data for clinical evaluation were collected. RESULTS: The mean follow-up time was 26 months, and the mean age was 35 years for 12 patients. The mean interval between the time of injury and the surgery was 6.1 days. Radiological fracture union was evident in all patients at 12 weeks. During surgery, the blood loss ranged from 100 to 300 mL, and the duration ranged from 55 to 90 min. The Tegner-Lysholm functional score ranged from 85 to 97 at the final follow-up. Moreover, the final Rasmussen functional score ranged from 25 to 29, and Rasmussen anatomical score ranged from 13 to 18. CONCLUSIONS: The newly designed anatomic locking plate for the posterolateral tibial plateau provided adequate fixation along the posterolateral tibial plateau. It proved to be safe and effective in a small-sample-size population (12 patients) during a 12- to 34-month follow-up.

Efficacy of internal fixation with mini plate and internal fixation with hollow screw for Regan-Morrey type II and III ulna coronoid fractures.

BACKGROUND: Ulna coronoid fracture is a complicated injury and occurred in the coronal plane. Undeniably, there is no universally accepted approach for treating ulna coronoid fractures. Therefore, this study aimed at exploring the efficacy of different surgical treatments for Regan-Morrey type II and III ulna coronoid fractures. METHODS: A total of 164 patients with ulna coronoid fractures were admitted and treated in department of orthopedics at Yiwu Central Hospital, the Affiliated Yiwu Hospital of Wenzhou Medical University for retrospective analysis. The baseline features (age, gender, time from injury to surgery and so on) before the surgery and different conditions during the surgery were compared. Following that, the Visual Analogue Scale (VAS) pain score was employed to evaluate the severity of preoperative and postoperative pain experienced by the patients in each group. Afterwards, Broberg and Morrey elbow score was used to evaluate elbow joint function and surgical effect of the patients. Lastly, the postoperative recovery and complications were compared. RESULTS: It was firstly observed that internal fixation with mini plate and hollow screw compelled to lower average operation time and blood loss than Kirschner wire and steel wire suture. Next, the severity of postoperative pain was lessened in comparison with preoperative pain. Afterwards, mini plate and hollow screw improved elbow joint function more notable than Kirschner wire and steel wire suture, and Kirschner wire and steel wire suture resulted in higher incidence of complications and worse postoperative recovery. CONCLUSION: Collectively, this study clarified that for the treatment of Regan-Morrey type II and III ulna coronoid fractures, internal fixation with mini plate and hollow screw has an overall superior surgical effect than internal fixation with Kirschner wire and steel wire suture.

A comparison of zero-profile anchored spacer (ROI-C) and plate fixation in 2-level noncontiguous anterior cervical discectomy and fusion- a retrospective study.

BACKGROUND: Anterior cervical discectomy and fusion (ACDF) is the classic surgical treatment for symptomatic cervical degenerative disc disease (CDDD). However, there is controversy over the best surgical management in patients with two noncontiguous symptomatic levels of CDDD. METHODS: From April 2011 to May 2014, 44 patients with two noncontiguous symptomatic levels of CDDD underwent skip-level ACDFs. In Group NoPlate, 23 cases underwent 2 noncontiguous levels of ACDF using zero-profile anchored spacer; and in Group Plate, 21 cases underwent 2 noncontiguous levels of ACDF using cages and plates. Operation-related paraeters for each group were recorded and compared. Japanese Orthopedic Association (JOA) scores and Neck Disability Index (NDI) scores at preoperation and postoperation were compared with at least a 2-year follow-up. Cervical lordosis was analyzed before surgery, 1 month after surgery, 3 months after surgery, and at final follow-up. RESULTS: Mean follow-up was 35.4 ± 6.5 (range 24-48) months. Significant improvement on the JOA, NDI scores and cervical lordosis was noted in each group (p < 0.05), and there were no significant difference in terms of JOA, NDI scores, cervical lordosis and fusion rate between the two groups (P > 0.05). The operation time in Group NoPlate was significantly shorter than in Group Plate (p < 0.05), and the incidence of dysphagia and adjacent segment degeneration in Group NoPlate was significantly lower than in Group Plate (p < 0.05). CONCLUSIONS: ROI-C and cages with plate fixation were both effective in two-level noncontiguous ACDF, and there were no significant difference in clinical outcomes, fusion rate, and cervical lordosis. However, ROI-C was associated with shorter operative time, lower incidence of dysphagia and adjacent segment degeneration.

Comparison among perfect-C®, zero-P®, and plates with a cage in single-level cervical degenerative disc disease.

BACKGROUND: We intended to analyze the efficacy of a new integrated cage and plate device called Perfect-C for anterior cervical discectomy and fusion (ACDF) to cure single-level cervical degenerative disc disease. METHODS: We enrolled 148 patients who were subjected to single-level ACDF with one of the following three surgical devices: a Perfect-C implant (41 patients), a Zero-P implant (36 patients), or a titanium plate with a polyetheretherketone (PEEK) cage (71 patients). We conducted a retrospective study to compare the clinical and radiological results among the three groups. RESULTS: The length of the operation, intraoperative blood loss, and duration of hospitalization were significantly lower in the Perfect-C group than in the Zero-P and plate-with-cage groups (P < 0.05). At the last follow-up visit, heterotopic ossification (HO) was not observed in any cases (0%) in the Perfect-C and Zero-P groups but was noted in 21 cases (30%) in the plate-with-cage group. The cephalad and caudal plate-to-disc distance (PDD) and the cephalad and caudal PDD/anterior body height (ABH) were significantly greater in the Perfect-C and Zero-P groups than in the plate-with-cage group (P < 0.05). Subsidence occurred in five cases (14%) in the Perfect-C group, in nine cases (25%) in the Zero-P group, and in 15 cases (21%) in the plate-with-cage group. Fusion occurred in 37 cases (90%) in the Perfect-C group, in 31 cases (86%) in the Zero-P group, and in 68 cases (95%) in the plate-with-cage group. CONCLUSIONS: The Perfect-C, Zero-P, and plate-with-cage devices are effective for treating single-level cervical degenerative disc disease. However, the Perfect-C implant has many advantages over both the Zero-P implant and conventional plate-cage treatments. The Perfect-C implant was associated with shorter operation times and hospitalization durations, less blood loss, and lower subsidence rates compared with the Zero-P implant or the titanium plate with a PEEK cage.

Osteosynthesis with Locking Plate for Proximal Humerus Fracture.

Background Approximately 5% of all fractures consists of proximal humeral fractures. In the elderly population, most of these fractures are related to osteoporosis. Internal fixation has led to unpredictable results, especially in patients with osteopenic bone and those with comminuted fractures. Objective To evaluate functional outcome and complications following proximal humerus fracture fixation using locking plate. Method This prospective observational study was conducted at Nepal Medical College and Teaching Hospital from February 2014 to June 2015. We reviewed 35 patients with proximal humerus fractures, who underwent open reduction and internal fixation with locking plate.Functional outcome was evaluated according to the ConstantMurley shoulder assessment. Result Fracture union was achieved in all cases with the mean time to union being 14.6 weeks (11-24 weeks). At the final follow up the mean constant murley score was 73.6 (48-94). There was total 8(22.85%) cases who developed complication. Conclusion Internal fixation with the locking plate for proximal humerus fractures provides stable construct with better functional outcome as it allows early shoulder mobilization.

Evaluation of Anterolateral Plating of Distal Third Tibial Fractures.

Background Distal one-third tibial fractures with or without articular involvement can be difficult to manage. Variety of treatment methods have been suggested for these injuries, including conservative treatment, external fixation with or without limited internal fixation, intramedullary nailing, plate fixation (medial or anterolateral) and more recently minimally invasive plate osteosynthesis (MIPO). All of these techniques have advantages and disadvantages. None of these techniques can be considered the "gold standard" for these injuries. Objective The objective of this prospective study was to evaluate the results of anterolateral plating of these fractures. Method Forty-five fractures of distal third of tibia were treated with open reduction and internal fixation with anterolateral tibial plate from December 2011 to December 2016. All the patients were followed up at least for nine months for the study. Radiological union was finally assessed in nine months. Result All the fractures united within nine months of plating without angulation in sagittal or coronal plane. One patient (2%) had limb length shortening of more than one cm. Full range of motion of ankle and knee joint was achieved compared to the normal side by nine months follow up. 17 (38%) patients developed marginal skin necrosis. Three (7%) patients developed superficial wound infection. These complications were seen more in patients in whom posterior below knee slab was used for pre-operative splintage (as compared to calcaneal traction). Conclusion Hence distal one-third tibial fractures with or without articular involvement can be treated with anterolateral tibial plate.

[Design of distal radius volar locking plates : Anatomical, surgical and biomechanical aspects]. / Design distaler volarer Radiusplatten : Anatomische, operationstechnische und biomechanische Gesichtspunkte.

The operative treatment of unstable distal radius fractures primarily aims for the anatomical reduction of the joint while addressing accompanying injuries. Anatomical reduction, stable fixation and early functional movement of the joint are the three cornerstones of modern treatment concepts of distal radius fractures. Distal radius volar locking plates play a major role in the treatment and rehabilitation of the most commonly occurring fracture in humans. This article outlines the different principles in the current design of available distal radius volar locking plates. The biomechanical aspects, anatomical findings and clinical evaluation that have influenced current design features and trends in new developments of the latest plates are emphasized. This is an ongoing process that is supported through the investigation and feedback of clinical science.

[Biomechanics of distal radius fractures : Basics principles and GPS treatment strategy for locking plate osteosynthesis]. / Biomechanik distaler Radiusfrakturen : Grundlagenverständnis und GPS-Behandlungsstrategie bei winkelstabiler Plattenosteosynthese.

Fractures of the distal radius are most commonly caused by hyperextension injuries of the wrist. Tensile forces and force vectors, strength of impact, bone strength and soft tissue tension create individually different fracture patterns. Metaphyseal comminution, loss of cortical support, ligament avulsion and shear fragments are defining parameters for fracture instability. The dislocation of the articular fragment follows the force vectors of the extrinsic forearm muscles bridging the joint. The goal-plan-standardized (GPS) treatment strategy has proven to be helpful in choosing the ideal individual treatment. It is based on individual patient demands on wrist function and an analysis of fracture instability in computed tomography (CT) scans. The "goal" is a realistic expectation assessed by patient and surgeon. The "plan" includes a benefit-risk analysis and selection of an appropriate treatment modality. The "standardized treatment" of surgical and follow-up treatment is based on biomechanical knowledge. Locking plate osteosynthesis aims to neutralize dislocating force vectors and to allow early active mobility. Unidirectional instability can be indirectly neutralized by palmar locking plate systems. A multidirectional instability can be addressed by multiple plating following the column theory. Distal shear and avulsion fractures may require a fragment-specific osteosynthesis approach.

Radiographic and clinical assessment on the accuracy and complications of C1 anterior lateral mass and C2 anterior pedicle screw placement in the TARP-III procedure: a study of 106 patients.

PURPOSE: To investigate the (1) radiographic and clinical accuracy of C1 anterior lateral mass screw (C1ALMS) and C2 anterior pedicle screw (C2APS) placement in the transoral atlantoaxial reduction plate (TARP)-III procedure, (2) screw insertion-associated clinical complications and (3) fusion status between C1 and C2. METHODS: Radiographic and clinical data were obtained from the electronic medical record system. Studies were carried out to assess the accuracy of C1ALMS and C2APS placement, the screw insertion-associated clinical complications and the fusion status between C1 and C2. Placement of the screws was assessed using the modified All India Institute of Medical Sciences outcome-based classification. RESULTS: Two-hundred and twelve C1ALMS and 207 C2APS in 106 patients were assessed. The ideal accurate rates were 92.0% (195) and 53.1% (110), and the acceptable accurate rates were 97.6% (207) and 87.0% (180), respectively. One patient died postoperatively due to C2 screw misplacement. There were no symptoms of neurologic and vertebral artery injuries in the rest of the patients. 102 patients (97.1%) achieved solid fusion between C1 and C2. No instrumentation failure due to delayed union or nonunion was observed. CONCLUSION: C1ALMS placement in TARP-III procedures appears to be safe. The cortical breach rate of C2APS is high though clinically the neurovascular complication rate is similar to that of posterior atlantoaxial procedures. Advanced navigation strategies may help improve the accuracy of C2APS placement and decrease potential complications.

Mono- versus polyaxial locking plates in distal femur fractures - a biomechanical comparison of the Non-Contact-Bridging- (NCB) and the PERILOC-plate.

BACKGROUND: The aim of this cadaveric study was to compare a polyaxial (NCB®, Zimmer) to a fixed-angle monoaxial locking plate (PERILOC®, Smith & Nephew) in comminuted fractures of the distal femur regarding stability of the construct. Up to date there is no published biomechanical data concerning polyaxial plating in cadaveric distal femurs. METHODS: Fourteen formalin fixed femora were scanned by dual-energy x-ray absorptiometry. As fracture model an unstable supracondylar comminuted fracture was simulated. Fractures were pairwise randomly fixed either with a mono- (group A) or a polyaxial (group B) distal femur plate. The samples were tested in a servohydraulic mechanical testing system starting with an axial loading of 200 N following an increase of 200 N in every step with 500 cycles in every sequence up to a maximum of 2 000 N. The end points were implant failure or relevant loss of reduction. Data records included for each specimen time, number of cycles, axial load and axial displacement. Statistical analysis was performed using the exact Wilcoxon signed rank test. RESULTS: The mean donor age at the time of death was 75 years. The bone mass density (BMD) of the femurs in both groups was comparable and showed no statistically significant differences. Five bones failed before reaching the maximum applied force of 2000 N. Distribution curves of all samples in both groups, showing the plastic deformation in relation to the axial force, showed no statistically significant differences. CONCLUSIONS: Operative stabilization of distal femur fractures can be successfully and equally well achieved using either a monoaxial or a polyaxial locking plate. Polyaxial screw fixation may have advantages if intramedullary implants are present.

Less than full circumferential fusion of a tibial nonunion is sufficient to achieve mechanically valid fusion--proof of concept using a finite element modeling approach.

BACKGROUND: Although minimally invasive approaches are widely used in many areas of orthopedic surgery nonunion therapy remains a domain of open surgery. Some attempts have been made to introduce minimally invasive procedures into nonunion therapy. However, these proof of concept studies showed fusion rates comparable to open approaches never gaining wider acceptance in the clinical community. We hypothesize that knowledge of mechanically relevant regions of a nonunion might reduce the complexity of percutaneous procedures, especially in complex fracture patterns, and further reduce the amount of cancellous bone that needs to be transplanted. The aim of this investigation is to provide a proof of concept concerning the hypothesis that mechanically stable fusion of a nonunion can be achieved with less than full circumferential fusion. METHODS: CT data of an artificial tibia with a complex fracture pattern and anatomical LCP are converted into a finite element mesh. The nonunion area is segmented. The finite element mesh is assigned mechanical properties according to data from the literature. An optimization algorithm is developed that reduces the number of voxels in the non union area until the scaled von Mises stress in the implant reaches 20% of the maximum stress in the implant/bone system that occurs with no fusion in the nonunion area at all. RESULTS: After six iterations of the optimization algorithm the number of voxels in the nonunion area is reduced by 96.4%, i.e. only 3.6% of voxels in the non union area are relevant for load transfer such that the von Mises stress in the implant/bone system does not exceed 20% of the maximal scaled von Mises stress occurring in the system with no fusion in the non union area at all. CONCLUSIONS: The hypothesis that less than full circumferential fusion is necessary for mechanical stability of a nonunion is confirmed. As the model provides only qualitative information the observed reduction of fusion area may not be taken literally but needs to be calibrated in future experiments. However this proof of concept provides the mechanical foundation for further development of minimally invasive approaches to delayed union and nonunion therapy.

Biomechanical testing of a unique built-in expandable anterior spinal internal fixation system.

BACKGROUND: Expandable screws have greater pullout strength than conventional screws. The purpose of this study was to compare the biomechanical stability provided by a new built-in expandable anterior spinal fixation system with that of 2 commonly used anterior fixation systems, the Z-Plate and the Kaneda, in a porcine partial vertebral corpectomy model. METHODS: Eighteen porcine thoracolumbar spine specimens were randomly divided into 3 groups of 6 each. A vertebral wedge osteotomy was performed by removing the anterior 2/3 of the L1 vertebral body and the T15/L1 disc. Vertebrae were fixed with the Z-Plate, Kaneda, or expandable fixation system. The 3-dimensional spinal range of motion (ROM) of specimens in the intact state (prior to osteotomy), injured state (after osteotomy), and after internal fixation were recorded. The pullout strength and maximum torque of common anterior screws, the expandable anterior fixation screw unexpanded, and the expandable anterior fixation screw expanded was tested. RESULTS: After internal fixation, the expandable device and Z-plate system exhibited higher left bending motion than the Kaneda system (5.50° and 5.37° vs. 5.04, p = 0.001 and 0.008, respectively), and the Z-plate and Kaneda groups had significantly higher left axial and right axial rotation ROM as compared to the expandable device group (left axial rotation: 5.23° and 5.02° vs. 4.53°; right axial rotation: 5.23° and 5.08° vs. 4.49°). The maximum insertion torque of the expandable device was significantly greater than of a common screw (5.10 vs. 3.75 Ns). The maximum pullout force of the expandable device expanded was significantly higher than that of the common screw and the expandable device unexpanded (3,035.48 N vs. 1,827.38 N and 2,333.49 N). CONCLUSIONS: The built-in anterior fixation system provides better axial rotational stability as compared to the other 2 systems, and greater maximum torque and pullout strength than a common fixation screw.

Mechanical behaviour of low-cost dynamic compression plates correlates with manufacturing quality standards.

PURPOSE: This study compares the mechanical properties of low-cost stainless steel dynamic compression plates (DCPs) from developing-world manufacturers, adhering to varying manufacturing quality standards, with those of high-cost DCPs manufactured for use in the developed world. METHODS: Standard-design ten-hole DCPs from six developing-world manufacturers and high-cost DCPs from two manufacturers in the developed world were studied. Nine plates from each manufacturer underwent mechanical testing: six in four-point monotonic bending to assess strength and stiffness and three in four-point bending fatigue. Statistical comparisons of the group means of monotonic bending test data were made, and a qualitative comparison was performed to assess failures in fatigue. RESULTS: Low-cost DCPs from manufacturers with at least one manufacturing quality standard had significantly higher bending strength and fewer failures in fatigue than did those from low-cost manufacturers with no recognised quality standards. High-cost DCPs demonstrated greater bending strength than did those in both low-cost groups. There were no differences in stiffness and fatigue failure between high-cost DCPs and those low-cost DCPs with quality standards. However, high-cost DCPs were significantly less stiff and had fewer fatigue failures than low-cost DCPs manufactured without such standards. CONCLUSION: Significant differences were found in the mechanical properties of ten-hole DCP plates from selected manufacturers in the developing and developed worlds. These differences correlated with reported quality certification in the manufacturing process. Mechanical analysis of low-cost implants may provide information useful in determining which manufacturers produce implants with the best potential for benefit relative to cost.

Effect of plate working length on plate stiffness and cyclic fatigue life in a cadaveric femoral fracture gap model stabilized with a 12-hole 2.4 mm locking compression plate.

BACKGROUND: There are several factors that can affect the fatigue life of a bone plate, including the mechanical properties of the plate and the complexity of the fracture. The position of the screws can influence construct stiffness, plate strain and cyclic fatigue of the implants. Studies have not investigated these variables in implants utilized for long bone fracture fixation in dogs and cats. The purpose of the present study was to evaluate the effect of plate working length on construct stiffness, gap motion and resistance to cyclic fatigue of dog femora with a simulated fracture gap stabilized using a 12-hole 2.4 mm locking compression plates (LCP). Femora were plated with 12-hole 2.4 mm LCP using 2 screws per fracture segment (long working length group) or with 12-hole 2.4 mm LCP using 5 screws per fracture segment (a short working length group). RESULTS: Construct stiffness did not differ significantly between stabilization techniques. Implant failure did not occur in any of the plated femora during cycling. Mean ± SD yield load at failure in the short plate working length group was significantly higher than in the long plate working length group. CONCLUSION: In a femoral fracture gap model stabilized with a 2.4 mm LCP applied in contact with the bone, plate working length had no effect on stiffness, gap motion and resistance to fatigue. The short plate working length constructs failed at higher loads; however, yield loads for both the short and long plate working length constructs were within physiologic range.