Stainability and translucency of potassium aluminum sulfate applied computer-aided design and computer-aided manufacturing materials after coffee thermocycling.

OBJECTIVE: The purpose of this in vitro study was to evaluate the effect of potassium aluminum sulfate (alum) application on the stainability and translucency of computer-aided design and computer-aided manufacturing (CAD-CAM) materials after coffee thermocycling (CTC). MATERIALS AND METHODS: Disk-shaped specimens (Ø10 × 1 mm; N = 200) were fabricated by using additively (Crowntec [CT] and Varseo Smile Crown Plus [VS]) and subtractively manufactured (Brilliant Crios [RCR], CEREC Block [FC], and Vita Enamic [VE]) CAD-CAM materials and polished. All specimens were randomly divided into two groups as alum applied and control (n = 10). All specimens were then subjected to CTC (10,000 cycles at 5-55°C) and color coordinates were measured at each time interval. Color differences (ΔE00 ) and relative translucency parameters (RTPs) were calculated and the data were statistically analyzed (a = 0.05). RESULTS: Among tested time intervals, alum applied specimens had their lowest ΔE00 after alum application (p ≤ 0.006), except for FC (p = 0.177). In addition, alum applied RCR had lower ΔE00 values than its control specimens (p = 0.029). Alum applied specimens had their lowest RTP after CTC (p < 0.001) and alum application decreased the RTP of CT (p = 0.010). CTC reduced the RTP of all materials in control groups (p < 0.001). Alum applied CT had higher RTP than its control specimens (p = 0.049). CONCLUSIONS: Alum application's effect on color change varied depending on the material and alum mostly resulted in clinically acceptable changes in translucency. CTC led to unacceptable color and translucency changes based on previously reported threshold values. CLINICAL SIGNIFICANCE: Optical properties of CAD-CAM materials and the sustainability of these properties over time is critical for longevity. Alum may improve the color stability of reinforced composite resin when subjected to long-term coffee consumption.

Biochemical evaluation of the therapeutic effectiveness of honey in oral mucosal ulcers.

The aim of this study was to describe and quantify the therapeutic value of honey in oral mucosal ulcers healing in comparison with Glyceroloxytriester (TGO). We also aimed to biochemically evaluate the healing effects of honey which had been collected from the Blacksea region flora on mucosal ulcers resulting in material loss.Thirty wistar rats (240+/-30 g) were enrolled in this study. Excisional wounds were performed in all rats for animal oral mucosal ulcer model. They were randomly allocated to three groups: group 1 was treated with Apitherapeutic agent or honey (0,1 ml, 2x1), group 2 was treated with TGO (0,1ml, 2x1) locally, Group 3 served as the control group.Following the surgical procedure on day 7, biopsy specimens were taken from right buccal mucosa and on day 14 biopsy specimens were taken from left bucal mucosa in all rats. Afterwards, hydroxy pyroline levels were measured. Data were analyzed statistically.There was no statistically significant difference between Group 1 and 2, and also between Group 2 and 3, but there was statistically significant difference between Group 1 and 3 on day 7. There was no statistically significant difference between Group 1, 2 and 3 on day 14.

Effect of denture base surface pretreatment on microleakage of a silicone-based resilient liner.

STATEMENT OF PROBLEM: Microleakage between resilient liner and denture base resins is a significant clinical problem, often responsible for debonding of the resilient liner from the denture base resin. PURPOSE: This study investigated the effect of 2 surface treatments, airborne-particle abrasion (APA) and wetting with methyl methacrylate monomer (MMA), on microleakage between a silicone-based resilient liner and denture base resin using a gamma camera imaging technique. MATERIAL AND METHODS: Thirty-three specimens, each having 2 plates measuring 40 x 40 x 2 mm, were prepared by packing and processing an acrylic denture base resin (QC-20) into square plates following manufacturer's instructions. Specimens were divided into 3 groups (n=11) as APA-, MMA-, and control-treatment groups. For the APA group, the inner surfaces of both plates were airborne-particle abraded with 250-microm Al 2 O 3 particles and, for the MMA group, surfaces were treated with monomer (QC-20). Control specimens were not surface treated. Following application of an adhesive (Ufi Gel P-specific), a silicone lining material (Ufi Gel P) was prepared and applied to the inner surfaces of all 33 specimens. Eleven size-matched polymethyl methacrylate (PMMA) specimen blocks (40 x 40 x 6 mm) were prepared to calculate the level of residual radioactivity for the denture base itself, the entire outer surface count (OSC). All specimens and PMMA blocks were immersed in a radioactive solution (thallium-201 chloride) for 24 hours. Specimen activities (gamma-ray cts/sec, representing thallium-201 concentration) were then measured using a high-resolution gamma camera. The amount of OSC-subtracted total specimen counts was a direct indicator of the quantity of inward diffusing tracer. The subtracted values were analyzed using a 1-way analysis of variance (ANOVA) and Bonferroni multiple comparison tests (alpha=.05). RESULTS: OSC levels averaged 754 +/- 110 gamma-ray cts/sec. OSC-subtracted APA, control, and MMA values were 5,546 +/- 1,534, 3,392 +/- 738, and 1,405 +/- 392 gamma-ray cts/sec, respectively. All 3 groups were significantly different ( P <.05) from each other. Surface wetting with MMA showed the lowest microleakage values among all specimen groups. CONCLUSION: In terms of microleakage, surface treatment with MMA monomer preceding the adhesive application demonstrated lower values than adhesive application alone. APA pretreatment resulted in 4 times the microleakage found in MMA-treated specimens, and 1.5 times the microleakage of the untreated control. None of the surface pretreatments completely prevented microleakage. Microleakage between the silicone-based resilient liner and denture base resin can be quantitatively determined using the gamma camera imaging technique.