Enhancement of the effects of intermittent parathyroid hormone (1-34) by bone morphogenetic protein in a rat femoral open fracture model.

BACKGROUND: Nonunion in cases of open fracture is common. Both bone morphogenetic protein 2 (BMP-2) and parathyroid hormone (PTH) have been used to enhance bone healing. We investigated the combination of BMP-2 and PTH and examined the effects on a rat model of open femoral fractures. METHODS: Group I (n = 11) was implanted with control carrier. Group II (n = 12) was implanted with carrier containing 1 µg of recombinant human BMP-2 (rhBMP-2). Group III (n = 12) was implanted with carrier alone, followed by injections of PTH 1-34. Group IV (n = 11) was implanted with carrier containing 1 µg of rhBMP-2, followed by injections of PTH 1-34. Group V (n = 11) was implanted with carrier containing 10 µg of rhBMP-2. Group VI (n = 11) was implanted with carrier containing 10 µg of rhBMP-2, followed by injections of PTH 1-34. Rats were euthanized after 8 weeks, and their fractured femurs were explanted and assessed by manual palpation, radiographs, micro-computerized tomography, and histological analysis. RESULTS: Manual palpation tests showed that the fusion rates of groups III (66.7%), IV (63.6%), V (81.8%), and VI (81.8%) were considerably higher than those of group I. Groups V and VI had higher radiographic scores compared to group I. Micro-CT analysis revealed enhanced bone marrow density expressed as bone volume/tissue volume in groups V (61.88 ± 3.16%) and VI (71.14 ± 3.89%) versus group I (58.26 ± 1.86%). A histological analysis indicated that group VI had enhanced remodeling. CONCLUSION: The combination of abundant rhBMP-2 and PTH enhanced bone healing and remodeling of newly formed bone in a rat femoral open fracture model.

Effect of ammonium hexafluorosilicate application for arresting caries treatment on demineralized primary tooth enamel.

Ammonium hexafluorosilicate (AHF) has been applied to arrest caries without discoloration. The purpose of this study was to observe structural and elemental changes of demineralized and AHF applied primary tooth enamel. Enamel from the labial surface of 20 primary canines was divided into an unground side and ground side at the center of the tooth, and demineralized with 35% phosphoric acid for 6 min. The teeth were divided into 4 groups according to a 3-min application of AHF and 1 week of soaking in artificial saliva, as follows: group A (neither AHF nor saliva), group B (only saliva), group C (only AHF), and group D (AHF and saliva), and then subdivided according to whether the enamel was ground or unground. Specimens were analyzed with scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). The data were statistically analyzed using ANOVA and Fisher's PLSD test at α = 0.05. In groups A and B, prism structures were seen, however, in groups C and D, enamel surfaces were covered with spherical particles. Ca/P ratio was significantly higher in groups C and D than in groups A and B. There was no significant difference between ground and unground enamel in the content of any element. The values for F, Na, Mg and Si persents and Ca/P ratio were significantly higher for the enamel surface than for points 10-30 µm beneath the surface. Results of this study suggest the possibility that AHF treatment arrests caries, although further study will be required to confirm this result.

Ability of barrier coat S-PRG coating to arrest artificial enamel lesions in primary teeth.

PURPOSE: To evaluate the effects of a surface pre-reacted glass-ionomer (S-PRG) filled coating material to arrest artificial enamel lesions in primary teeth. METHODS: Buccal and lingual enamel was demineralized in 0.1 M lactic acid buffer solution (pH 4.75) for 5 days and then divided in the PRG-applied and non-PRG areas. Proximal surfaces were used as a control area without demineralization and coating application. Teeth were divided into three groups (n = 4) according to the 1-week immersion in different solutions: Group 1 (distilled water), Group 2 (demineralizing solution) and Group 3 (artificial saliva). Hardness and Young's modulus by nano-indentation test, and elemental contents and ultrastructure by SEM/EDX analysis were obtained. Data were statistically analyzed using ANOVA and Fisher's PLSD at alpha = 0.05. RESULTS: Only for the non-PRG area in Group 1, the hardness and Young's modulus of the demineralized surface enamel were significantly lower than those of the enamel 30-60 microm beneath the surface. Demineralized enamel of non-PRG and PRG-applied areas showed similar SEM views. Only for the non-PRG area in Group 2 and control area in Group 3, the Ca/P of the surface enamel was significantly higher than that of the enamel 5-10 microm beneath the surface. There was no significant difference of the Ca/P among the measuring points from the surface to 10 microm depth of enamel for the PRG applied area in Group 2.

Influence of polishing instruments on the surface texture of resin composites.

OBJECTIVE: There is a need for an ideal polishing system for resin composite restorations. The purpose of this study was to investigate the influence of polishing instruments on the surface texture of light-cured resin composites. METHODS AND MATERIALS: Four polishing systems-Compomaster (Shofu), Silicone Points C Type (Shofu), Super-Snap (Shofu), and Enhance Finishing and Polishing System (Dentsply/DeTrey)-were used to polish the flat surface of cylindrical blocks made of 3 different resin composites: Beautifil (Shofu), Clearfil AP-X (Kuraray Medical), and Lite-Fil II A (Shofu). The average surface roughness (Ra) and surface gloss (Gs60 degrees) were determined. Scanning electron microscopic observations of the polished specimens were made. The polished samples were immersed in a 0.3% acid rhodamine B solution for 1 week, and change in color was determined. RESULTS: The multiple-step systems, Enhance and Super-Snap, resulted in the best surface finishes. A new single-step point, Compomaster, ranked third in surface finish but was significantly better than the older point system, Silicone Points C. The color-staining experiments showed that there were no significant differences between the Compomaster system and the multiple-step systems, which were all significantly better than the older polishing point. CONCLUSION: The newly introduced 1-step polishing point has the ability to polish resin composites as effectively as multistep polishing systems.