Valorization of Spent coffee Grounds: A sustainable resource for Bio-based phase change materials for thermal energy storage.

Spent coffee grounds (SCGs) are waste residues arising from the process of coffee brewing and are usually sent to landfills, causing environmental concerns. SCGs contain a considerable amount of fatty acids and is therefore a promising green alternative bio-based phase change material (PCMs) compared to conventional organic and inorganic PCMs. In this study, the extraction of coffee oil from SCGs was conducted using three different organic solvents-ethanol, acetone, and hexane. The chemical composition, chemical, and thermophysical properties of these coffee oil extracts were studied to evaluate their feasibility as a bio-based PCM. Gas chromatography-mass spectroscopy (GC-MS) analysis indicated that coffee oil contains about 60-80 % of fatty acids while the phase transition temperature of the coffee oil extracts is approximately 4.5 ± 0.72 °C, with latent heat values of 51.15 ± 1.46 J/g as determined by differential scanning calorimetry (DSC). Fourier Transform Infrared Spectroscopy (FTIR) and DSC results of coffee oil extracts after thermal cycling revealed good thermal and chemical stability. An application study to evaluate coffee oil extract as a potential cold therapy modality showed that it can maintain temperatures below normal body temperature for up to 46 min. In conclusion, this work exemplifies the potential of SCGs as a promising green and sustainable resource for bio-based PCMs for low-temperature thermal energy storage applications such as cold-chain transportation and cold therapy.

Preparation and thermal conductivity enhancement of a paraffin wax-based composite phase change material doped with garlic stem biochar microparticles.

The addition of thermally conductive nanomaterials is an effective strategy for increasing the thermal conductivity of phase change materials (PCMs). However, nanomaterials are expensive and may significantly reduce the latent heat capacity of PCMs. In this study, low-cost and eco-friendly biochar microparticles were prepared from garlic stems, a common food waste in Singapore. The thermal properties of paraffin wax (PW) doped with 1, 3, and 5 wt% garlic stem biochar (GSB) microparticles were investigated. The GSB microparticles prepared at 700 °C had three-dimensional porous and two-dimensional flake-like structures, which contributed to the formation of additional heat transfer pathways in the PW. The addition of 5 wt% GSB microparticles enhanced the thermal conductivity of PW by 27.3% and 7.2% in the solid and liquid phases, respectively. The T-history test revealed that the melting and solidification rates of PW improved by 90 and 115 s, respectively. The improved heat transfer performance was mainly ascribed to the high degree of graphitization and the interconnected porous carbon structure of the GSB microparticles. The phase change temperatures of PW were slightly changed upon the addition of GSB microparticles, and the latent heat capacity was only reduced by 6.1%. These results suggest that the GSB microparticles can be used as a potential alternative to other nanoadditives such as metal- and metal oxide-based nanoadditives.

Microfluidic Preparation of Janus Microparticles With Temperature and pH Triggered Degradation Properties.

Based on the phase separation phenomenon in micro-droplets, polymer-lipid Janus particles were prepared on a microfluidic flow focusing chip. Phase separation of droplets was caused by solvent volatilization and Janus morphology was formed under the action of interfacial tension. Because phase change from solid to liquid of the lipid hemisphere could be triggered by physiological temperature, the lipid hemisphere could be used for rapid release of drugs. While the polymer we selected was pH sensitive that the polymer hemisphere could degrade under acidic conditions, making it possible to release drugs in a specific pH environment, such as tumor tissues. Janus particles with different structures were obtained by changing the experimental conditions. To widen the application range of the particles, fatty alcohol and fatty acid-based phase change materials were also employed to prepare the particles, such as 1-tetradecanol, 1-hexadecanol and lauric acid. The melting points of these substances are higher than the physiological temperature, which can be applied in fever triggered drug release or in thermotherapy. The introduction of poly (lactic-co-glycolic acid) enabled the formation of multicompartment particles with three distinct materials. With different degradation properties of each compartment, the particles generated in this work may find applications in programmed and sequential drug release triggered by multiple stimuli.

A Computational Evaluation of the temperature distribution generated by thermal splints designed to treat knee pain.

A 3D modeling study was performed to evaluate the temperature distribution produced due to knee thermal splints to facilitate future investigations into the possible relationship between the temperature distribution and the pain relief related performance of the splints. Water and phase change material (PCM) were used as splint fillers at two different temperatures (42 °C and 44 °C). Free cooling and a temperature-controlled thermal splint were also considered. The study showed that a PCM filled splint or a temperature-controlled splint produced relatively larger and deeper temperature changes compared to the one produced with a water filled splint. With a PCM filled splint it was possible to reach a temperature increase of 1 °C in muscle tissue (42.61 cm3) and not only in fatty tissue.

Characterization of Unripe and Mature Avocado Seed Oil in Different Proportions as Phase Change Materials and Simulation of Their Cooling Storage.

Environmental problems have been associated with energy consumption and waste management. A solution is the development of renewable materials such as organic phase change materials. Characterization of new materials allows knowing their applications and simulations provide an idea of how they can developed. Consequently, this research is focused on the thermal and chemical characterization of five different avocado seed oils depending on the maturity stage of the seed: 100% unripe, 25% mature-75% unripe, 50% mature-50% unripe, 75% mature-25% unripe, and 100% mature. The characterization was performed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The best oil for natural environments corresponded to 100% matured seed with an enthalpy of fusion of 52.93 J·g-1, and a degradation temperature between 241-545 °C. In addition, the FTIR analysis shows that unripe seed oil seems to contain more lipids than a mature one. Furthermore, a simulation with an isothermal box was conducted with the characterized oil with an initial temperature of -14 °C for the isothermal box, -27 °C for the PCM box, and an ambient temperature of 25 °C. The results show that without the PCM the temperature can reach -8 °C and with it is -12 °C after 7 h, proving its application as a cold thermal energy system.

Spent coffee grounds as supporting materials to produce bio-composite PCM with natural waxes.

Novel kinds of bio composite Phase change materials were prepared by the use of bio-wastes. Of the by-products, coffee wastes, which is currently consumed and abandoned as coffee as a drink, was used as the supporting material for PCM. It was found through chemical composition of FTIR of SCBW, SCPW, SCGW and that the coffee wastes were effectively vacuum impregnated into each natural wax. As a result of TGA, the thermal stability of SCBW, SCPW, SCGW and SCNW was checked. In addition, the DSC results were used to determine the heat storage performance of each material. Micro-morphological analysis with FE-SEM showed whether the impregnation was successful. The use of bio-compatible PCM by-products is economical as well as environmentally friendly and is sufficient for building applications in terms of thermal performance compared to other bio-composites.

Mesoporous gold nanoparticles for photothermal controlled anticancer drug delivery.

Aim: To realize the transit and release of cancer drug exactly as well as high drug loading ratio, we reported a biocompatible and temperature responsive controlled drug delivery system based on 3D mesoporous structured Au networks. Materials & methods: Here, we filled the hollow interiors of Au networks with a phase-change material so that the drug release was easily regulated by controlling the temperature only. Results: Thanks to the high near-infrared reflectance absorbance and mesoporous structure, the Au-PEG + lauric acid/doxorubicin system showed a strong photothermal conversion efficiency, high drug-loading ratio (54.2% for doxorubicin) and controlled drug release. Conclusion: This system revealed great advantages in photothermal therapy and chemotherapy, offering an obvious synergistic effect in cancer treatment.

Multifunctional Thermosensitive Liposomes Based on Natural Phase-Change Material: Near-Infrared Light-Triggered Drug Release and Multimodal Imaging-Guided Cancer Combination Therapy.

Multifunctional theranostic nanoplatforms (NPs) in response to environment stimulations for on-demand drug release are highly desirable. Herein, the near-infrared (NIR)-absorbing dye, indocyanine green (ICG), and the antitumor drug, doxorubicin (DOX), were efficiently coencapsulated into the thermosensitive liposomes based on natural phase-change material. Folate and conjugated gadolinium (Gd) chelate-modified liposome shells enhance active targeting and magnetic resonance performance of the NPs while maintaining the size of the NPs. The ICG/DOX-loaded and gadolinium chelate conjugated temperature-sensitive liposome nanoplatforms (ID@TSL-Gd NPs) exhibited NIR-triggered drug release and prominent chemo-, photothermal, and photodynamic therapy properties. With the coencapsulated ICG, DOX, and the conjugated gadolinium chelates, the ID@TSL-Gd NPs can be used for triple-modal imaging (fluorescence/photoacoustic/magnetic resonance imaging)-guided combination tumor therapy (chemotherapy, photothermotherapy, and photodynamic therapy). After tail vein injection, the ID@TSL-Gd NPs accumulated effectively in subcutaneous HeLa tumor of mice. The tumor was effectively suppressed by accurate imaging-guided NIR-triggered phototherapy and chemotherapy, and no tumor regression and side effects were observed. In summary, the prepared ID@TSL-Gd NPs achieved multimodal imaging-guided cancer combination therapy, providing a promising platform for improving diagnosis and treatment of cancer.

Combination cancer treatment through photothermally controlled release of selenous acid from gold nanocages.

Selenite, one of the inorganic forms of selenium, is emerging as an attractive chemotherapeutic agent owing to its selectivity in eradicating cancer cells. Here we demonstrate a new formulation of nanomedicine based on selenous acid, which is mixed with lauric acid (a phase-change material with a melting point around 43 °C) and then loaded into the cavities of Au nanocages. The Au nanocages can serve as a carrier during cell endocytosis and then as a photothermal agent to melt the lauric acid upon the irradiation with a near-infrared laser, triggering the swift release of selenous acid. The photothermal and chemo therapies can also work synergistically, leading to enhanced destruction of cancer cells relative to normal cells. Our systematic study suggests that the impaired mitochondrial function arising from the ROS generated through combination treatment is responsible for the cell death. This study offers an appealing candidate that holds great promise for synergistic cancer treatment.

Drug "Pent-Up" in Hollow Magnetic Prussian Blue Nanoparticles for NIR-Induced Chemo-Photothermal Tumor Therapy with Trimodal Imaging.

The study reports a biocompatible smart drug delivery system based on a doxorubicin (DOX) blending phase-change material of 1-pentadecanol loaded hollow magnetic Prussian blue nanoparticles, resulting in HMNP-PB@Pent@DOX. The system possesses concentration-dependent high thermogenesis (>50 °C) when applying a near-infrared (NIR) laser irradiation only for 5 min. Furthermore, the system realizes near "zero release" of drug and is efficiently triggered by NIR for drug delivery in an "on" and "off" manner, thus inducing cell apoptosis in vitro and in vivo. Moreover, the system clearly indicates tumor site with trimodal imaging of magnetic resonance imaging, photoacoustic tomography imaging, and infrared thermal imaging. Furthermore, the system achieves efficient chemo-photothermal combined tumor therapy in vivo with 808 nm laser irradiation for 5 min at 1.2 W cm-2 , revealing the good tumor inhibition effect comparing with those of chemotherapy or photothermal therapy alone. The system is also confirmed to be biocompatible in regard to the mortality rate.